@@ -720,79 +720,79 @@ static int af9015_copy_firmware(struct dvb_usb_device *d)
struct af9015_state *state = d_to_priv(d);
struct usb_interface *intf = d->intf;
int ret;
- u8 fw_params[4];
- u8 val, i;
- struct req_t req = {COPY_FIRMWARE, 0, 0x5100, 0, 0, sizeof(fw_params),
- fw_params };
+ unsigned long timeout;
+ u8 val, firmware_info[4];
+ struct req_t req = {COPY_FIRMWARE, 0, 0x5100, 0, 0, 4, firmware_info};
dev_dbg(&intf->dev, "\n");
- fw_params[0] = state->firmware_size >> 8;
- fw_params[1] = state->firmware_size & 0xff;
- fw_params[2] = state->firmware_checksum >> 8;
- fw_params[3] = state->firmware_checksum & 0xff;
+ firmware_info[0] = (state->firmware_size >> 8) & 0xff;
+ firmware_info[1] = (state->firmware_size >> 0) & 0xff;
+ firmware_info[2] = (state->firmware_checksum >> 8) & 0xff;
+ firmware_info[3] = (state->firmware_checksum >> 0) & 0xff;
- ret = af9015_read_reg_i2c(d, state->af9013_i2c_addr[1],
- 0x98be, &val);
+ /* Check whether firmware is already running */
+ ret = af9015_read_reg_i2c(d, state->af9013_i2c_addr[1], 0x98be, &val);
if (ret)
- goto error;
- else
- dev_dbg(&intf->dev, "firmware status %02x\n", val);
+ goto err;
- if (val == 0x0c) /* fw is running, no need for download */
- goto exit;
+ dev_dbg(&intf->dev, "firmware status %02x\n", val);
- /* set I2C master clock to fast (to speed up firmware copy) */
- ret = af9015_write_reg(d, 0xd416, 0x04); /* 0x04 * 400ns */
- if (ret)
- goto error;
+ if (val == 0x0c)
+ return 0;
- msleep(50);
+ /* Set i2c clock to 625kHz to speed up firmware copy */
+ ret = af9015_write_reg(d, 0xd416, 0x04);
+ if (ret)
+ goto err;
- /* copy firmware */
+ /* Copy firmware from master demod to slave demod */
ret = af9015_ctrl_msg(d, &req);
- if (ret)
+ if (ret) {
dev_err(&intf->dev, "firmware copy cmd failed %d\n", ret);
+ goto err;
+ }
- dev_dbg(&intf->dev, "firmware copy done\n");
-
- /* set I2C master clock back to normal */
- ret = af9015_write_reg(d, 0xd416, 0x14); /* 0x14 * 400ns */
+ /* Set i2c clock to 125kHz */
+ ret = af9015_write_reg(d, 0xd416, 0x14);
if (ret)
- goto error;
+ goto err;
- /* request boot firmware */
- ret = af9015_write_reg_i2c(d, state->af9013_i2c_addr[1],
- 0xe205, 1);
- dev_dbg(&intf->dev, "firmware boot cmd status %d\n", ret);
+ /* Boot firmware */
+ ret = af9015_write_reg_i2c(d, state->af9013_i2c_addr[1], 0xe205, 0x01);
if (ret)
- goto error;
+ goto err;
- for (i = 0; i < 15; i++) {
- msleep(100);
+ /* Poll firmware ready */
+ for (val = 0x00, timeout = jiffies + msecs_to_jiffies(1000);
+ !time_after(jiffies, timeout) && val != 0x0c && val != 0x04;) {
+ msleep(20);
- /* check firmware status */
+ /* Check firmware status. 0c=OK, 04=fail */
ret = af9015_read_reg_i2c(d, state->af9013_i2c_addr[1],
- 0x98be, &val);
- dev_dbg(&intf->dev, "firmware status cmd status %d, firmware status %02x\n",
- ret, val);
+ 0x98be, &val);
if (ret)
- goto error;
+ goto err;
- if (val == 0x0c || val == 0x04) /* success or fail */
- break;
+ dev_dbg(&intf->dev, "firmware status %02x\n", val);
}
+ dev_dbg(&intf->dev, "firmware boot took %u ms\n",
+ jiffies_to_msecs(jiffies) - (jiffies_to_msecs(timeout) - 1000));
+
if (val == 0x04) {
- ret = -ETIMEDOUT;
+ ret = -ENODEV;
dev_err(&intf->dev, "firmware did not run\n");
+ goto err;
} else if (val != 0x0c) {
ret = -ETIMEDOUT;
dev_err(&intf->dev, "firmware boot timeout\n");
+ goto err;
}
-error:
-exit:
+ return 0;
+err:
+ dev_dbg(&intf->dev, "failed %d\n", ret);
return ret;
}
Small improvements. Signed-off-by: Antti Palosaari <crope@iki.fi> --- drivers/media/usb/dvb-usb-v2/af9015.c | 88 +++++++++++++++++------------------ 1 file changed, 44 insertions(+), 44 deletions(-)