| Message ID | 1525295174-15995-3-git-send-email-mgautam@codeaurora.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
Hi, On Wed, May 2, 2018 at 2:06 PM, Manu Gautam <mgautam@codeaurora.org> wrote: > QMP PHY for USB/PCIE requires pipe_clk for locking of > retime buffers at the pipe interface. Driver checks for > PHY_STATUS without enabling pipe_clk due to which > phy_init() fails with initialization timeout. > Though pipe_clk is output from PHY (after PLL is programmed > during initialization sequence) to GCC clock_ctl and then fed > back to PHY but for PHY_STATUS register to reflect successful > initialization pipe_clk from GCC must be present. > Since, clock driver now ignores status_check for pipe_clk on > clk_enable/disable, driver can safely enable/disable pipe_clk > from phy_init/exit. > > Signed-off-by: Manu Gautam <mgautam@codeaurora.org> > --- > drivers/phy/qualcomm/phy-qcom-qmp.c | 22 ++++++++-------------- > 1 file changed, 8 insertions(+), 14 deletions(-) Given the agreement with Stephen Boyd that we'll just BRANCH_HALT_SKIP for now, this all looks good to me. Reviewed-by: Douglas Anderson <dianders@chromium.org> -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c index 6470c5d..fddb1c9 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c @@ -793,19 +793,6 @@ static void qcom_qmp_phy_configure(void __iomem *base, } } -static int qcom_qmp_phy_poweron(struct phy *phy) -{ - struct qmp_phy *qphy = phy_get_drvdata(phy); - struct qcom_qmp *qmp = qphy->qmp; - int ret; - - ret = clk_prepare_enable(qphy->pipe_clk); - if (ret) - dev_err(qmp->dev, "pipe_clk enable failed, err=%d\n", ret); - - return ret; -} - static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp) { const struct qmp_phy_cfg *cfg = qmp->cfg; @@ -974,6 +961,12 @@ static int qcom_qmp_phy_init(struct phy *phy) } } + ret = clk_prepare_enable(qphy->pipe_clk); + if (ret) { + dev_err(qmp->dev, "pipe_clk enable failed err=%d\n", ret); + goto err_clk_enable; + } + /* Tx, Rx, and PCS configurations */ qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num); /* Configuration for other LANE for USB-DP combo PHY */ @@ -1019,6 +1012,8 @@ static int qcom_qmp_phy_init(struct phy *phy) return ret; err_pcs_ready: + clk_disable_unprepare(qphy->pipe_clk); +err_clk_enable: if (cfg->has_lane_rst) reset_control_assert(qphy->lane_rst); err_lane_rst: @@ -1283,7 +1278,6 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) static const struct phy_ops qcom_qmp_phy_gen_ops = { .init = qcom_qmp_phy_init, .exit = qcom_qmp_phy_exit, - .power_on = qcom_qmp_phy_poweron, .set_mode = qcom_qmp_phy_set_mode, .owner = THIS_MODULE, };
QMP PHY for USB/PCIE requires pipe_clk for locking of retime buffers at the pipe interface. Driver checks for PHY_STATUS without enabling pipe_clk due to which phy_init() fails with initialization timeout. Though pipe_clk is output from PHY (after PLL is programmed during initialization sequence) to GCC clock_ctl and then fed back to PHY but for PHY_STATUS register to reflect successful initialization pipe_clk from GCC must be present. Since, clock driver now ignores status_check for pipe_clk on clk_enable/disable, driver can safely enable/disable pipe_clk from phy_init/exit. Signed-off-by: Manu Gautam <mgautam@codeaurora.org> --- drivers/phy/qualcomm/phy-qcom-qmp.c | 22 ++++++++-------------- 1 file changed, 8 insertions(+), 14 deletions(-)