diff mbox

[RFC,3/6] hwmon: Add support for RPi voltage sensor

Message ID 1526477827-10859-4-git-send-email-stefan.wahren@i2se.com (mailing list archive)
State New, archived
Headers show

Commit Message

Stefan Wahren May 16, 2018, 1:37 p.m. UTC
Currently there is no easy way to detect under-voltage conditions on a remote
Raspberry Pi. This hwmon driver retrieves the state of the under-voltage sensor
via mailbox interface. The handling based on Noralf's modifications to the
downstream firmware driver. In case of an under-voltage condition only an entry
is written to the kernel log.

CC: "Noralf Trønnes" <noralf@tronnes.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
 drivers/hwmon/Kconfig             |  10 ++
 drivers/hwmon/Makefile            |   1 +
 drivers/hwmon/raspberrypi-hwmon.c | 207 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 218 insertions(+)
 create mode 100644 drivers/hwmon/raspberrypi-hwmon.c

Comments

Robin Murphy May 16, 2018, 1:51 p.m. UTC | #1
Hi Stefan,

On 16/05/18 14:37, Stefan Wahren wrote:
> Currently there is no easy way to detect under-voltage conditions on a remote
> Raspberry Pi. This hwmon driver retrieves the state of the under-voltage sensor
> via mailbox interface. The handling based on Noralf's modifications to the
> downstream firmware driver. In case of an under-voltage condition only an entry
> is written to the kernel log.
> 
> CC: "Noralf Trønnes" <noralf@tronnes.org>
> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
> ---
>   drivers/hwmon/Kconfig             |  10 ++
>   drivers/hwmon/Makefile            |   1 +
>   drivers/hwmon/raspberrypi-hwmon.c | 207 ++++++++++++++++++++++++++++++++++++++
>   3 files changed, 218 insertions(+)
>   create mode 100644 drivers/hwmon/raspberrypi-hwmon.c
> 
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 768aed5..7f935cf 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -1298,6 +1298,16 @@ config SENSORS_PWM_FAN
>   	  This driver can also be built as a module.  If so, the module
>   	  will be called pwm-fan.
>   
> +config SENSORS_RASPBERRYPI_HWMON
> +	tristate "Raspberry Pi voltage monitor"
> +	depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)

Since RASPBERRYPI_FIRMWARE already implies ARCH_BCM2835 (via 
BCM2835_MBOX), this is just a very roundabout way to say:

	depends on RASPBERRYPI_FIRMWARE || COMPILE_TEST

Robin.

> +	help
> +	  If you say yes here you get support for voltage sensor on the
> +	  Raspberry Pi.
> +
> +	  This driver can also be built as a module. If so, the module
> +	  will be called raspberrypi-hwmon.
> +
>   config SENSORS_SHT15
>   	tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
>   	depends on GPIOLIB || COMPILE_TEST
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index e7d52a3..a929770 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -141,6 +141,7 @@ obj-$(CONFIG_SENSORS_PC87427)	+= pc87427.o
>   obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
>   obj-$(CONFIG_SENSORS_POWR1220)  += powr1220.o
>   obj-$(CONFIG_SENSORS_PWM_FAN)	+= pwm-fan.o
> +obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON)	+= raspberrypi-hwmon.o
>   obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
>   obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
>   obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
> diff --git a/drivers/hwmon/raspberrypi-hwmon.c b/drivers/hwmon/raspberrypi-hwmon.c
> new file mode 100644
> index 0000000..2003f6c
> --- /dev/null
> +++ b/drivers/hwmon/raspberrypi-hwmon.c
> @@ -0,0 +1,207 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Raspberry Pi voltage sensor driver
> + *
> + * Based on firmware/raspberrypi.c by Noralf Trønnes
> + *
> + * Copyright (C) 2018 Stefan Wahren <stefan.wahren@i2se.com>
> + */
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/hwmon.h>
> +#include <linux/hwmon-sysfs.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/workqueue.h>
> +#include <soc/bcm2835/raspberrypi-firmware.h>
> +
> +#define UNDERVOLTAGE_STICKY_BIT	BIT(16)
> +
> +struct rpi_hwmon_data {
> +	struct device *hwmon_dev;
> +	struct rpi_firmware *fw;
> +	u32 last_throttled;
> +	struct delayed_work get_values_poll_work;
> +};
> +
> +static void rpi_firmware_get_throttled(struct rpi_hwmon_data *data)
> +{
> +	u32 new_uv, old_uv, value;
> +	int ret;
> +
> +	/* Clear sticky bits */
> +	value = 0xffff;
> +
> +	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> +				    &value, sizeof(value));
> +	if (ret) {
> +		dev_err_once(data->hwmon_dev, "%s: Failed to get throttled (%d)\n",
> +			     __func__, ret);
> +		return;
> +	}
> +
> +	new_uv = value & UNDERVOLTAGE_STICKY_BIT;
> +	old_uv = data->last_throttled & UNDERVOLTAGE_STICKY_BIT;
> +	data->last_throttled = value;
> +
> +	if (new_uv == old_uv)
> +		return;
> +
> +	if (new_uv)
> +		dev_crit(data->hwmon_dev, "Under-voltage detected! (0x%08x)\n",
> +			 value);
> +	else
> +		dev_info(data->hwmon_dev, "Voltage normalised (0x%08x)\n",
> +			 value);
> +
> +	sysfs_notify(&data->hwmon_dev->kobj, NULL, "in0_lcrit_alarm");
> +}
> +
> +static void get_values_poll(struct work_struct *work)
> +{
> +	struct rpi_hwmon_data *data;
> +
> +	data = container_of(work, struct rpi_hwmon_data,
> +			    get_values_poll_work.work);
> +
> +	rpi_firmware_get_throttled(data);
> +
> +	/*
> +	 * We can't run faster than the sticky shift (100ms) since we get
> +	 * flipping in the sticky bits that are cleared.
> +	 */
> +	schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> +}
> +
> +static int rpi_read(struct device *dev, enum hwmon_sensor_types type,
> +		    u32 attr, int channel, long *val)
> +{
> +	struct rpi_hwmon_data *data = dev_get_drvdata(dev);
> +
> +	if (type != hwmon_in)
> +		return -EOPNOTSUPP;
> +
> +	if (attr != hwmon_in_lcrit_alarm)
> +		return -EOPNOTSUPP;
> +
> +	if (channel)
> +		return -EOPNOTSUPP;
> +
> +	*val = !!(data->last_throttled & UNDERVOLTAGE_STICKY_BIT);
> +	return 0;
> +}
> +
> +static umode_t rpi_is_visible(const void *_data, enum hwmon_sensor_types type,
> +			      u32 attr, int channel)
> +{
> +	if (type != hwmon_in)
> +		return 0;
> +
> +	if (attr != hwmon_in_lcrit_alarm)
> +		return 0;
> +
> +	if (channel)
> +		return 0;
> +
> +	return 0444;
> +}
> +
> +static const u32 rpi_in_config[] = {
> +	HWMON_I_LCRIT_ALARM,
> +	0
> +};
> +
> +static const struct hwmon_channel_info rpi_in = {
> +	.type = hwmon_in,
> +	.config = rpi_in_config,
> +};
> +
> +static const struct hwmon_channel_info *rpi_info[] = {
> +	&rpi_in,
> +	NULL
> +};
> +
> +static const struct hwmon_ops rpi_hwmon_ops = {
> +	.is_visible = rpi_is_visible,
> +	.read = rpi_read,
> +};
> +
> +static const struct hwmon_chip_info rpi_chip_info = {
> +	.ops = &rpi_hwmon_ops,
> +	.info = rpi_info,
> +};
> +
> +static int rpi_hwmon_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct device_node *fw_node;
> +	struct rpi_hwmon_data *data;
> +	int ret;
> +
> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> +	if (!data)
> +		return -ENOMEM;
> +
> +	fw_node = of_get_parent(dev->of_node);
> +	if (!fw_node) {
> +		dev_err(dev, "Missing firmware node\n");
> +		return -ENOENT;
> +	}
> +
> +	data->fw = rpi_firmware_get(fw_node);
> +	of_node_put(fw_node);
> +	if (!data->fw)
> +		return -EPROBE_DEFER;
> +
> +	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> +				    &data->last_throttled,
> +				    sizeof(data->last_throttled));
> +	if (ret) {
> +		dev_info(dev, "Firmware doesn't support GET_THROTTLED\n");
> +		return -EOPNOTSUPP;
> +	}
> +
> +	data->hwmon_dev = devm_hwmon_device_register_with_info(dev, "rpi_volt",
> +							       data,
> +							       &rpi_chip_info,
> +							       NULL);
> +
> +	INIT_DELAYED_WORK(&data->get_values_poll_work, get_values_poll);
> +	platform_set_drvdata(pdev, data);
> +
> +	if (!PTR_ERR_OR_ZERO(data->hwmon_dev))
> +		schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> +
> +	return PTR_ERR_OR_ZERO(data->hwmon_dev);
> +}
> +
> +static int rpi_hwmon_remove(struct platform_device *pdev)
> +{
> +	struct rpi_hwmon_data *data = platform_get_drvdata(pdev);
> +
> +	cancel_delayed_work_sync(&data->get_values_poll_work);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id rpi_hwmon_of_match[] = {
> +	{ .compatible = "raspberrypi,bcm2835-hwmon", },
> +	{ /* sentinel */},
> +};
> +MODULE_DEVICE_TABLE(of, rpi_hwmon_of_match);
> +
> +static struct platform_driver rpi_hwmon_driver = {
> +	.probe = rpi_hwmon_probe,
> +	.remove = rpi_hwmon_remove,
> +	.driver = {
> +		.name = "raspberrypi-hwmon",
> +		.of_match_table = rpi_hwmon_of_match,
> +	},
> +};
> +module_platform_driver(rpi_hwmon_driver);
> +
> +MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
> +MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
> +MODULE_LICENSE("GPL v2");
>
Guenter Roeck May 16, 2018, 6:05 p.m. UTC | #2
On Wed, May 16, 2018 at 02:51:49PM +0100, Robin Murphy wrote:
> Hi Stefan,
> 
> On 16/05/18 14:37, Stefan Wahren wrote:
> >Currently there is no easy way to detect under-voltage conditions on a remote
> >Raspberry Pi. This hwmon driver retrieves the state of the under-voltage sensor
> >via mailbox interface. The handling based on Noralf's modifications to the
> >downstream firmware driver. In case of an under-voltage condition only an entry
> >is written to the kernel log.
> >
> >CC: "Noralf Trønnes" <noralf@tronnes.org>
> >Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
> >---
> >  drivers/hwmon/Kconfig             |  10 ++
> >  drivers/hwmon/Makefile            |   1 +
> >  drivers/hwmon/raspberrypi-hwmon.c | 207 ++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 218 insertions(+)
> >  create mode 100644 drivers/hwmon/raspberrypi-hwmon.c
> >
> >diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> >index 768aed5..7f935cf 100644
> >--- a/drivers/hwmon/Kconfig
> >+++ b/drivers/hwmon/Kconfig
> >@@ -1298,6 +1298,16 @@ config SENSORS_PWM_FAN
> >  	  This driver can also be built as a module.  If so, the module
> >  	  will be called pwm-fan.
> >+config SENSORS_RASPBERRYPI_HWMON
> >+	tristate "Raspberry Pi voltage monitor"
> >+	depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
> 
> Since RASPBERRYPI_FIRMWARE already implies ARCH_BCM2835 (via BCM2835_MBOX),
> this is just a very roundabout way to say:
> 
> 	depends on RASPBERRYPI_FIRMWARE || COMPILE_TEST
> 
That would permit SENSORS_RASPBERRYPI_HWMON=y combined with
RASPBERRYPI_FIRMWARE=m, which AFAICS would result in a build error
because include/soc/bcm2835/raspberrypi-firmware.h uses IS_ENABLED()
and not IS_REACHABLE().

Guenter

> Robin.
> 
> >+	help
> >+	  If you say yes here you get support for voltage sensor on the
> >+	  Raspberry Pi.
> >+
> >+	  This driver can also be built as a module. If so, the module
> >+	  will be called raspberrypi-hwmon.
> >+
> >  config SENSORS_SHT15
> >  	tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
> >  	depends on GPIOLIB || COMPILE_TEST
> >diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> >index e7d52a3..a929770 100644
> >--- a/drivers/hwmon/Makefile
> >+++ b/drivers/hwmon/Makefile
> >@@ -141,6 +141,7 @@ obj-$(CONFIG_SENSORS_PC87427)	+= pc87427.o
> >  obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
> >  obj-$(CONFIG_SENSORS_POWR1220)  += powr1220.o
> >  obj-$(CONFIG_SENSORS_PWM_FAN)	+= pwm-fan.o
> >+obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON)	+= raspberrypi-hwmon.o
> >  obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
> >  obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
> >  obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
> >diff --git a/drivers/hwmon/raspberrypi-hwmon.c b/drivers/hwmon/raspberrypi-hwmon.c
> >new file mode 100644
> >index 0000000..2003f6c
> >--- /dev/null
> >+++ b/drivers/hwmon/raspberrypi-hwmon.c
> >@@ -0,0 +1,207 @@
> >+// SPDX-License-Identifier: GPL-2.0+
> >+/*
> >+ * Raspberry Pi voltage sensor driver
> >+ *
> >+ * Based on firmware/raspberrypi.c by Noralf Trønnes
> >+ *
> >+ * Copyright (C) 2018 Stefan Wahren <stefan.wahren@i2se.com>
> >+ */
> >+#include <linux/device.h>
> >+#include <linux/err.h>
> >+#include <linux/hwmon.h>
> >+#include <linux/hwmon-sysfs.h>
> >+#include <linux/module.h>
> >+#include <linux/of_device.h>
> >+#include <linux/platform_device.h>
> >+#include <linux/slab.h>
> >+#include <linux/workqueue.h>
> >+#include <soc/bcm2835/raspberrypi-firmware.h>
> >+
> >+#define UNDERVOLTAGE_STICKY_BIT	BIT(16)
> >+
> >+struct rpi_hwmon_data {
> >+	struct device *hwmon_dev;
> >+	struct rpi_firmware *fw;
> >+	u32 last_throttled;
> >+	struct delayed_work get_values_poll_work;
> >+};
> >+
> >+static void rpi_firmware_get_throttled(struct rpi_hwmon_data *data)
> >+{
> >+	u32 new_uv, old_uv, value;
> >+	int ret;
> >+
> >+	/* Clear sticky bits */
> >+	value = 0xffff;
> >+
> >+	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> >+				    &value, sizeof(value));
> >+	if (ret) {
> >+		dev_err_once(data->hwmon_dev, "%s: Failed to get throttled (%d)\n",
> >+			     __func__, ret);
> >+		return;
> >+	}
> >+
> >+	new_uv = value & UNDERVOLTAGE_STICKY_BIT;
> >+	old_uv = data->last_throttled & UNDERVOLTAGE_STICKY_BIT;
> >+	data->last_throttled = value;
> >+
> >+	if (new_uv == old_uv)
> >+		return;
> >+
> >+	if (new_uv)
> >+		dev_crit(data->hwmon_dev, "Under-voltage detected! (0x%08x)\n",
> >+			 value);
> >+	else
> >+		dev_info(data->hwmon_dev, "Voltage normalised (0x%08x)\n",
> >+			 value);
> >+
> >+	sysfs_notify(&data->hwmon_dev->kobj, NULL, "in0_lcrit_alarm");
> >+}
> >+
> >+static void get_values_poll(struct work_struct *work)
> >+{
> >+	struct rpi_hwmon_data *data;
> >+
> >+	data = container_of(work, struct rpi_hwmon_data,
> >+			    get_values_poll_work.work);
> >+
> >+	rpi_firmware_get_throttled(data);
> >+
> >+	/*
> >+	 * We can't run faster than the sticky shift (100ms) since we get
> >+	 * flipping in the sticky bits that are cleared.
> >+	 */
> >+	schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> >+}
> >+
> >+static int rpi_read(struct device *dev, enum hwmon_sensor_types type,
> >+		    u32 attr, int channel, long *val)
> >+{
> >+	struct rpi_hwmon_data *data = dev_get_drvdata(dev);
> >+
> >+	if (type != hwmon_in)
> >+		return -EOPNOTSUPP;
> >+
> >+	if (attr != hwmon_in_lcrit_alarm)
> >+		return -EOPNOTSUPP;
> >+
> >+	if (channel)
> >+		return -EOPNOTSUPP;
> >+
> >+	*val = !!(data->last_throttled & UNDERVOLTAGE_STICKY_BIT);
> >+	return 0;
> >+}
> >+
> >+static umode_t rpi_is_visible(const void *_data, enum hwmon_sensor_types type,
> >+			      u32 attr, int channel)
> >+{
> >+	if (type != hwmon_in)
> >+		return 0;
> >+
> >+	if (attr != hwmon_in_lcrit_alarm)
> >+		return 0;
> >+
> >+	if (channel)
> >+		return 0;
> >+
> >+	return 0444;
> >+}
> >+
> >+static const u32 rpi_in_config[] = {
> >+	HWMON_I_LCRIT_ALARM,
> >+	0
> >+};
> >+
> >+static const struct hwmon_channel_info rpi_in = {
> >+	.type = hwmon_in,
> >+	.config = rpi_in_config,
> >+};
> >+
> >+static const struct hwmon_channel_info *rpi_info[] = {
> >+	&rpi_in,
> >+	NULL
> >+};
> >+
> >+static const struct hwmon_ops rpi_hwmon_ops = {
> >+	.is_visible = rpi_is_visible,
> >+	.read = rpi_read,
> >+};
> >+
> >+static const struct hwmon_chip_info rpi_chip_info = {
> >+	.ops = &rpi_hwmon_ops,
> >+	.info = rpi_info,
> >+};
> >+
> >+static int rpi_hwmon_probe(struct platform_device *pdev)
> >+{
> >+	struct device *dev = &pdev->dev;
> >+	struct device_node *fw_node;
> >+	struct rpi_hwmon_data *data;
> >+	int ret;
> >+
> >+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> >+	if (!data)
> >+		return -ENOMEM;
> >+
> >+	fw_node = of_get_parent(dev->of_node);
> >+	if (!fw_node) {
> >+		dev_err(dev, "Missing firmware node\n");
> >+		return -ENOENT;
> >+	}
> >+
> >+	data->fw = rpi_firmware_get(fw_node);
> >+	of_node_put(fw_node);
> >+	if (!data->fw)
> >+		return -EPROBE_DEFER;
> >+
> >+	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> >+				    &data->last_throttled,
> >+				    sizeof(data->last_throttled));
> >+	if (ret) {
> >+		dev_info(dev, "Firmware doesn't support GET_THROTTLED\n");
> >+		return -EOPNOTSUPP;
> >+	}
> >+
> >+	data->hwmon_dev = devm_hwmon_device_register_with_info(dev, "rpi_volt",
> >+							       data,
> >+							       &rpi_chip_info,
> >+							       NULL);
> >+
> >+	INIT_DELAYED_WORK(&data->get_values_poll_work, get_values_poll);
> >+	platform_set_drvdata(pdev, data);
> >+
> >+	if (!PTR_ERR_OR_ZERO(data->hwmon_dev))
> >+		schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> >+
> >+	return PTR_ERR_OR_ZERO(data->hwmon_dev);
> >+}
> >+
> >+static int rpi_hwmon_remove(struct platform_device *pdev)
> >+{
> >+	struct rpi_hwmon_data *data = platform_get_drvdata(pdev);
> >+
> >+	cancel_delayed_work_sync(&data->get_values_poll_work);
> >+
> >+	return 0;
> >+}
> >+
> >+static const struct of_device_id rpi_hwmon_of_match[] = {
> >+	{ .compatible = "raspberrypi,bcm2835-hwmon", },
> >+	{ /* sentinel */},
> >+};
> >+MODULE_DEVICE_TABLE(of, rpi_hwmon_of_match);
> >+
> >+static struct platform_driver rpi_hwmon_driver = {
> >+	.probe = rpi_hwmon_probe,
> >+	.remove = rpi_hwmon_remove,
> >+	.driver = {
> >+		.name = "raspberrypi-hwmon",
> >+		.of_match_table = rpi_hwmon_of_match,
> >+	},
> >+};
> >+module_platform_driver(rpi_hwmon_driver);
> >+
> >+MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
> >+MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
> >+MODULE_LICENSE("GPL v2");
> >
> --
> To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
Guenter Roeck May 16, 2018, 6:21 p.m. UTC | #3
On Wed, May 16, 2018 at 03:37:04PM +0200, Stefan Wahren wrote:
> Currently there is no easy way to detect under-voltage conditions on a remote
> Raspberry Pi. This hwmon driver retrieves the state of the under-voltage sensor
> via mailbox interface. The handling based on Noralf's modifications to the
> downstream firmware driver. In case of an under-voltage condition only an entry
> is written to the kernel log.
> 

My major concern is how this is displayed with the 'sensors' command.
Can you test and report ?

Of course, it would be much better if the firmware would also report
the actual voltage, but I guess we can't have everything.

More comments inline.

Thanks,
Guenter

> CC: "Noralf Trønnes" <noralf@tronnes.org>
> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
> ---
>  drivers/hwmon/Kconfig             |  10 ++
>  drivers/hwmon/Makefile            |   1 +
>  drivers/hwmon/raspberrypi-hwmon.c | 207 ++++++++++++++++++++++++++++++++++++++

Please also provide Documentation/hwmon/raspberrypi-hwmon.

>  3 files changed, 218 insertions(+)
>  create mode 100644 drivers/hwmon/raspberrypi-hwmon.c
> 
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 768aed5..7f935cf 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -1298,6 +1298,16 @@ config SENSORS_PWM_FAN
>  	  This driver can also be built as a module.  If so, the module
>  	  will be called pwm-fan.
>  
> +config SENSORS_RASPBERRYPI_HWMON
> +	tristate "Raspberry Pi voltage monitor"
> +	depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
> +	help
> +	  If you say yes here you get support for voltage sensor on the
> +	  Raspberry Pi.
> +
> +	  This driver can also be built as a module. If so, the module
> +	  will be called raspberrypi-hwmon.
> +
>  config SENSORS_SHT15
>  	tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
>  	depends on GPIOLIB || COMPILE_TEST
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index e7d52a3..a929770 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -141,6 +141,7 @@ obj-$(CONFIG_SENSORS_PC87427)	+= pc87427.o
>  obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
>  obj-$(CONFIG_SENSORS_POWR1220)  += powr1220.o
>  obj-$(CONFIG_SENSORS_PWM_FAN)	+= pwm-fan.o
> +obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON)	+= raspberrypi-hwmon.o
>  obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
>  obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
>  obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
> diff --git a/drivers/hwmon/raspberrypi-hwmon.c b/drivers/hwmon/raspberrypi-hwmon.c
> new file mode 100644
> index 0000000..2003f6c
> --- /dev/null
> +++ b/drivers/hwmon/raspberrypi-hwmon.c
> @@ -0,0 +1,207 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Raspberry Pi voltage sensor driver
> + *
> + * Based on firmware/raspberrypi.c by Noralf Trønnes
> + *
> + * Copyright (C) 2018 Stefan Wahren <stefan.wahren@i2se.com>
> + */
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/hwmon.h>
> +#include <linux/hwmon-sysfs.h>

Unnecessary include

> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/workqueue.h>
> +#include <soc/bcm2835/raspberrypi-firmware.h>
> +
> +#define UNDERVOLTAGE_STICKY_BIT	BIT(16)
> +
> +struct rpi_hwmon_data {
> +	struct device *hwmon_dev;
> +	struct rpi_firmware *fw;
> +	u32 last_throttled;
> +	struct delayed_work get_values_poll_work;
> +};
> +
> +static void rpi_firmware_get_throttled(struct rpi_hwmon_data *data)
> +{
> +	u32 new_uv, old_uv, value;
> +	int ret;
> +
> +	/* Clear sticky bits */

Please make more explicit that this is a request/command sent to the firmware.

> +	value = 0xffff;
> +
> +	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> +				    &value, sizeof(value));
> +	if (ret) {
> +		dev_err_once(data->hwmon_dev, "%s: Failed to get throttled (%d)\n",
> +			     __func__, ret);

The function name seems unnecessary.

> +		return;
> +	}
> +
> +	new_uv = value & UNDERVOLTAGE_STICKY_BIT;
> +	old_uv = data->last_throttled & UNDERVOLTAGE_STICKY_BIT;
> +	data->last_throttled = value;
> +
> +	if (new_uv == old_uv)
> +		return;
> +
> +	if (new_uv)
> +		dev_crit(data->hwmon_dev, "Under-voltage detected! (0x%08x)\n",
> +			 value);
> +	else
> +		dev_info(data->hwmon_dev, "Voltage normalised (0x%08x)\n",
> +			 value);

What value do those hex values provide to the user ?

> +
> +	sysfs_notify(&data->hwmon_dev->kobj, NULL, "in0_lcrit_alarm");
> +}
> +
> +static void get_values_poll(struct work_struct *work)
> +{
> +	struct rpi_hwmon_data *data;
> +
> +	data = container_of(work, struct rpi_hwmon_data,
> +			    get_values_poll_work.work);
> +
> +	rpi_firmware_get_throttled(data);
> +
> +	/*
> +	 * We can't run faster than the sticky shift (100ms) since we get
> +	 * flipping in the sticky bits that are cleared.
> +	 */
> +	schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> +}
> +
> +static int rpi_read(struct device *dev, enum hwmon_sensor_types type,
> +		    u32 attr, int channel, long *val)
> +{
> +	struct rpi_hwmon_data *data = dev_get_drvdata(dev);
> +
> +	if (type != hwmon_in)
> +		return -EOPNOTSUPP;
> +
> +	if (attr != hwmon_in_lcrit_alarm)
> +		return -EOPNOTSUPP;
> +
> +	if (channel)
> +		return -EOPNOTSUPP;
> +
There is only one channel, one attribute, and one type supported.
As such, the checks are unnecessary.

> +	*val = !!(data->last_throttled & UNDERVOLTAGE_STICKY_BIT);
> +	return 0;
> +}
> +
> +static umode_t rpi_is_visible(const void *_data, enum hwmon_sensor_types type,
> +			      u32 attr, int channel)
> +{
> +	if (type != hwmon_in)
> +		return 0;
> +
> +	if (attr != hwmon_in_lcrit_alarm)
> +		return 0;
> +
> +	if (channel)
> +		return 0;

Same as above. In the list below, there is not a single conditional attribute.
Given that, the checks should be unnecessary, and it should be sufficient to
just return 0444.

> +
> +	return 0444;
> +}
> +
> +static const u32 rpi_in_config[] = {
> +	HWMON_I_LCRIT_ALARM,
> +	0
> +};
> +
> +static const struct hwmon_channel_info rpi_in = {
> +	.type = hwmon_in,
> +	.config = rpi_in_config,
> +};
> +
> +static const struct hwmon_channel_info *rpi_info[] = {
> +	&rpi_in,
> +	NULL
> +};
> +
> +static const struct hwmon_ops rpi_hwmon_ops = {
> +	.is_visible = rpi_is_visible,
> +	.read = rpi_read,
> +};
> +
> +static const struct hwmon_chip_info rpi_chip_info = {
> +	.ops = &rpi_hwmon_ops,
> +	.info = rpi_info,
> +};
> +
> +static int rpi_hwmon_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct device_node *fw_node;
> +	struct rpi_hwmon_data *data;
> +	int ret;
> +
> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> +	if (!data)
> +		return -ENOMEM;
> +
> +	fw_node = of_get_parent(dev->of_node);
> +	if (!fw_node) {
> +		dev_err(dev, "Missing firmware node\n");
> +		return -ENOENT;
> +	}
> +
> +	data->fw = rpi_firmware_get(fw_node);
> +	of_node_put(fw_node);
> +	if (!data->fw)
> +		return -EPROBE_DEFER;
> +
> +	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> +				    &data->last_throttled,
> +				    sizeof(data->last_throttled));
> +	if (ret) {
> +		dev_info(dev, "Firmware doesn't support GET_THROTTLED\n");

If this is an error -> dev_err().

> +		return -EOPNOTSUPP;

or return -ENODEV.

> +	}
> +
> +	data->hwmon_dev = devm_hwmon_device_register_with_info(dev, "rpi_volt",
> +							       data,
> +							       &rpi_chip_info,
> +							       NULL);
> +
> +	INIT_DELAYED_WORK(&data->get_values_poll_work, get_values_poll);
> +	platform_set_drvdata(pdev, data);
> +
> +	if (!PTR_ERR_OR_ZERO(data->hwmon_dev))
> +		schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> +
> +	return PTR_ERR_OR_ZERO(data->hwmon_dev);
> +}
> +
> +static int rpi_hwmon_remove(struct platform_device *pdev)
> +{
> +	struct rpi_hwmon_data *data = platform_get_drvdata(pdev);
> +
> +	cancel_delayed_work_sync(&data->get_values_poll_work);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id rpi_hwmon_of_match[] = {
> +	{ .compatible = "raspberrypi,bcm2835-hwmon", },
> +	{ /* sentinel */},
> +};
> +MODULE_DEVICE_TABLE(of, rpi_hwmon_of_match);
> +
> +static struct platform_driver rpi_hwmon_driver = {
> +	.probe = rpi_hwmon_probe,
> +	.remove = rpi_hwmon_remove,
> +	.driver = {
> +		.name = "raspberrypi-hwmon",
> +		.of_match_table = rpi_hwmon_of_match,
> +	},
> +};
> +module_platform_driver(rpi_hwmon_driver);
> +
> +MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
> +MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.7.4
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
Robin Murphy May 16, 2018, 6:23 p.m. UTC | #4
On 16/05/18 19:05, Guenter Roeck wrote:
> On Wed, May 16, 2018 at 02:51:49PM +0100, Robin Murphy wrote:
>> Hi Stefan,
>>
>> On 16/05/18 14:37, Stefan Wahren wrote:
>>> Currently there is no easy way to detect under-voltage conditions on a remote
>>> Raspberry Pi. This hwmon driver retrieves the state of the under-voltage sensor
>>> via mailbox interface. The handling based on Noralf's modifications to the
>>> downstream firmware driver. In case of an under-voltage condition only an entry
>>> is written to the kernel log.
>>>
>>> CC: "Noralf Trønnes" <noralf@tronnes.org>
>>> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
>>> ---
>>>   drivers/hwmon/Kconfig             |  10 ++
>>>   drivers/hwmon/Makefile            |   1 +
>>>   drivers/hwmon/raspberrypi-hwmon.c | 207 ++++++++++++++++++++++++++++++++++++++
>>>   3 files changed, 218 insertions(+)
>>>   create mode 100644 drivers/hwmon/raspberrypi-hwmon.c
>>>
>>> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
>>> index 768aed5..7f935cf 100644
>>> --- a/drivers/hwmon/Kconfig
>>> +++ b/drivers/hwmon/Kconfig
>>> @@ -1298,6 +1298,16 @@ config SENSORS_PWM_FAN
>>>   	  This driver can also be built as a module.  If so, the module
>>>   	  will be called pwm-fan.
>>> +config SENSORS_RASPBERRYPI_HWMON
>>> +	tristate "Raspberry Pi voltage monitor"
>>> +	depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
>>
>> Since RASPBERRYPI_FIRMWARE already implies ARCH_BCM2835 (via BCM2835_MBOX),
>> this is just a very roundabout way to say:
>>
>> 	depends on RASPBERRYPI_FIRMWARE || COMPILE_TEST
>>
> That would permit SENSORS_RASPBERRYPI_HWMON=y combined with
> RASPBERRYPI_FIRMWARE=m, which AFAICS would result in a build error
> because include/soc/bcm2835/raspberrypi-firmware.h uses IS_ENABLED()
> and not IS_REACHABLE().

But that's only possible when COMPILE_TEST=y, where in any case there 
are stub definitions for the #else case in that header which should 
still be enough to build with, right? (and if not, that's probably its 
own bug)

Nobody's expecting COMPILE_TEST configs to actually boot and work 
perfectly, are they?

Robin.
Stefan Wahren May 16, 2018, 7:59 p.m. UTC | #5
Hi Guenter,

> Guenter Roeck <linux@roeck-us.net> hat am 16. Mai 2018 um 20:21 geschrieben:
> 
> 
> On Wed, May 16, 2018 at 03:37:04PM +0200, Stefan Wahren wrote:
> > Currently there is no easy way to detect under-voltage conditions on a remote
> > Raspberry Pi. This hwmon driver retrieves the state of the under-voltage sensor
> > via mailbox interface. The handling based on Noralf's modifications to the
> > downstream firmware driver. In case of an under-voltage condition only an entry
> > is written to the kernel log.
> > 
> 
> My major concern is how this is displayed with the 'sensors' command.
> Can you test and report ?

I get the following output:
rpi_volt-isa-0000
Adapter: ISA adapter
in0:              N/A  

> 
> Of course, it would be much better if the firmware would also report
> the actual voltage, but I guess we can't have everything.

I think this isn't possible because the hardware only provide a binary value (GPIO).

> 
> More comments inline.
> 
> Thanks,
> Guenter
> 
> > CC: "Noralf Trønnes" <noralf@tronnes.org>
> > Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
> > ---
> >  drivers/hwmon/Kconfig             |  10 ++
> >  drivers/hwmon/Makefile            |   1 +
> >  drivers/hwmon/raspberrypi-hwmon.c | 207 ++++++++++++++++++++++++++++++++++++++
> 
> Please also provide Documentation/hwmon/raspberrypi-hwmon.
> 
> >  3 files changed, 218 insertions(+)
> >  create mode 100644 drivers/hwmon/raspberrypi-hwmon.c
> > 
> > diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> > index 768aed5..7f935cf 100644
> > --- a/drivers/hwmon/Kconfig
> > +++ b/drivers/hwmon/Kconfig
> > @@ -1298,6 +1298,16 @@ config SENSORS_PWM_FAN
> >  	  This driver can also be built as a module.  If so, the module
> >  	  will be called pwm-fan.
> >  
> > +config SENSORS_RASPBERRYPI_HWMON
> > +	tristate "Raspberry Pi voltage monitor"
> > +	depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
> > +	help
> > +	  If you say yes here you get support for voltage sensor on the
> > +	  Raspberry Pi.
> > +
> > +	  This driver can also be built as a module. If so, the module
> > +	  will be called raspberrypi-hwmon.
> > +
> >  config SENSORS_SHT15
> >  	tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
> >  	depends on GPIOLIB || COMPILE_TEST
> > diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> > index e7d52a3..a929770 100644
> > --- a/drivers/hwmon/Makefile
> > +++ b/drivers/hwmon/Makefile
> > @@ -141,6 +141,7 @@ obj-$(CONFIG_SENSORS_PC87427)	+= pc87427.o
> >  obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
> >  obj-$(CONFIG_SENSORS_POWR1220)  += powr1220.o
> >  obj-$(CONFIG_SENSORS_PWM_FAN)	+= pwm-fan.o
> > +obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON)	+= raspberrypi-hwmon.o
> >  obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
> >  obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
> >  obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
> > diff --git a/drivers/hwmon/raspberrypi-hwmon.c b/drivers/hwmon/raspberrypi-hwmon.c
> > new file mode 100644
> > index 0000000..2003f6c
> > --- /dev/null
> > +++ b/drivers/hwmon/raspberrypi-hwmon.c
> > @@ -0,0 +1,207 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Raspberry Pi voltage sensor driver
> > + *
> > + * Based on firmware/raspberrypi.c by Noralf Trønnes
> > + *
> > + * Copyright (C) 2018 Stefan Wahren <stefan.wahren@i2se.com>
> > + */
> > +#include <linux/device.h>
> > +#include <linux/err.h>
> > +#include <linux/hwmon.h>
> > +#include <linux/hwmon-sysfs.h>
> 
> Unnecessary include
> 
> > +#include <linux/module.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/slab.h>
> > +#include <linux/workqueue.h>
> > +#include <soc/bcm2835/raspberrypi-firmware.h>
> > +
> > +#define UNDERVOLTAGE_STICKY_BIT	BIT(16)
> > +
> > +struct rpi_hwmon_data {
> > +	struct device *hwmon_dev;
> > +	struct rpi_firmware *fw;
> > +	u32 last_throttled;
> > +	struct delayed_work get_values_poll_work;
> > +};
> > +
> > +static void rpi_firmware_get_throttled(struct rpi_hwmon_data *data)
> > +{
> > +	u32 new_uv, old_uv, value;
> > +	int ret;
> > +
> > +	/* Clear sticky bits */
> 
> Please make more explicit that this is a request/command sent to the firmware.
> 
> > +	value = 0xffff;
> > +
> > +	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> > +				    &value, sizeof(value));
> > +	if (ret) {
> > +		dev_err_once(data->hwmon_dev, "%s: Failed to get throttled (%d)\n",
> > +			     __func__, ret);
> 
> The function name seems unnecessary.
> 
> > +		return;
> > +	}
> > +
> > +	new_uv = value & UNDERVOLTAGE_STICKY_BIT;
> > +	old_uv = data->last_throttled & UNDERVOLTAGE_STICKY_BIT;
> > +	data->last_throttled = value;
> > +
> > +	if (new_uv == old_uv)
> > +		return;
> > +
> > +	if (new_uv)
> > +		dev_crit(data->hwmon_dev, "Under-voltage detected! (0x%08x)\n",
> > +			 value);
> > +	else
> > +		dev_info(data->hwmon_dev, "Voltage normalised (0x%08x)\n",
> > +			 value);
> 
> What value do those hex values provide to the user ?

The actual definition of the bits can be found in the commit log of patch #1. But this isn't very helpful for an end user.

> 
> > +
> > +	sysfs_notify(&data->hwmon_dev->kobj, NULL, "in0_lcrit_alarm");
> > +}
> > +
> > +static void get_values_poll(struct work_struct *work)
> > +{
> > +	struct rpi_hwmon_data *data;
> > +
> > +	data = container_of(work, struct rpi_hwmon_data,
> > +			    get_values_poll_work.work);
> > +
> > +	rpi_firmware_get_throttled(data);
> > +
> > +	/*
> > +	 * We can't run faster than the sticky shift (100ms) since we get
> > +	 * flipping in the sticky bits that are cleared.
> > +	 */
> > +	schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> > +}
> > +
> > +static int rpi_read(struct device *dev, enum hwmon_sensor_types type,
> > +		    u32 attr, int channel, long *val)
> > +{
> > +	struct rpi_hwmon_data *data = dev_get_drvdata(dev);
> > +
> > +	if (type != hwmon_in)
> > +		return -EOPNOTSUPP;
> > +
> > +	if (attr != hwmon_in_lcrit_alarm)
> > +		return -EOPNOTSUPP;
> > +
> > +	if (channel)
> > +		return -EOPNOTSUPP;
> > +
> There is only one channel, one attribute, and one type supported.
> As such, the checks are unnecessary.
> 
> > +	*val = !!(data->last_throttled & UNDERVOLTAGE_STICKY_BIT);
> > +	return 0;
> > +}
> > +
> > +static umode_t rpi_is_visible(const void *_data, enum hwmon_sensor_types type,
> > +			      u32 attr, int channel)
> > +{
> > +	if (type != hwmon_in)
> > +		return 0;
> > +
> > +	if (attr != hwmon_in_lcrit_alarm)
> > +		return 0;
> > +
> > +	if (channel)
> > +		return 0;
> 
> Same as above. In the list below, there is not a single conditional attribute.
> Given that, the checks should be unnecessary, and it should be sufficient to
> just return 0444.
> 
> > +
> > +	return 0444;
> > +}
> > +
> > +static const u32 rpi_in_config[] = {
> > +	HWMON_I_LCRIT_ALARM,
> > +	0
> > +};
> > +
> > +static const struct hwmon_channel_info rpi_in = {
> > +	.type = hwmon_in,
> > +	.config = rpi_in_config,
> > +};
> > +
> > +static const struct hwmon_channel_info *rpi_info[] = {
> > +	&rpi_in,
> > +	NULL
> > +};
> > +
> > +static const struct hwmon_ops rpi_hwmon_ops = {
> > +	.is_visible = rpi_is_visible,
> > +	.read = rpi_read,
> > +};
> > +
> > +static const struct hwmon_chip_info rpi_chip_info = {
> > +	.ops = &rpi_hwmon_ops,
> > +	.info = rpi_info,
> > +};
> > +
> > +static int rpi_hwmon_probe(struct platform_device *pdev)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct device_node *fw_node;
> > +	struct rpi_hwmon_data *data;
> > +	int ret;
> > +
> > +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> > +	if (!data)
> > +		return -ENOMEM;
> > +
> > +	fw_node = of_get_parent(dev->of_node);
> > +	if (!fw_node) {
> > +		dev_err(dev, "Missing firmware node\n");
> > +		return -ENOENT;
> > +	}
> > +
> > +	data->fw = rpi_firmware_get(fw_node);
> > +	of_node_put(fw_node);
> > +	if (!data->fw)
> > +		return -EPROBE_DEFER;
> > +
> > +	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> > +				    &data->last_throttled,
> > +				    sizeof(data->last_throttled));
> > +	if (ret) {
> > +		dev_info(dev, "Firmware doesn't support GET_THROTTLED\n");
> 
> If this is an error -> dev_err().

I wasn't sure. If the firmware is too old, we cannot provide this feature and it's a waste of resources to load this driver. On the other side i don't want to confuse people this is something bad.

Stefan

> 
> > +		return -EOPNOTSUPP;
> 
> or return -ENODEV.
> 
> > +	}
> > +
> > +	data->hwmon_dev = devm_hwmon_device_register_with_info(dev, "rpi_volt",
> > +							       data,
> > +							       &rpi_chip_info,
> > +							       NULL);
> > +
> > +	INIT_DELAYED_WORK(&data->get_values_poll_work, get_values_poll);
> > +	platform_set_drvdata(pdev, data);
> > +
> > +	if (!PTR_ERR_OR_ZERO(data->hwmon_dev))
> > +		schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> > +
> > +	return PTR_ERR_OR_ZERO(data->hwmon_dev);
> > +}
> > +
> > +static int rpi_hwmon_remove(struct platform_device *pdev)
> > +{
> > +	struct rpi_hwmon_data *data = platform_get_drvdata(pdev);
> > +
> > +	cancel_delayed_work_sync(&data->get_values_poll_work);
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct of_device_id rpi_hwmon_of_match[] = {
> > +	{ .compatible = "raspberrypi,bcm2835-hwmon", },
> > +	{ /* sentinel */},
> > +};
> > +MODULE_DEVICE_TABLE(of, rpi_hwmon_of_match);
> > +
> > +static struct platform_driver rpi_hwmon_driver = {
> > +	.probe = rpi_hwmon_probe,
> > +	.remove = rpi_hwmon_remove,
> > +	.driver = {
> > +		.name = "raspberrypi-hwmon",
> > +		.of_match_table = rpi_hwmon_of_match,
> > +	},
> > +};
> > +module_platform_driver(rpi_hwmon_driver);
> > +
> > +MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
> > +MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
> > +MODULE_LICENSE("GPL v2");
> > -- 
> > 2.7.4
> > 
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Guenter Roeck May 17, 2018, 4:43 p.m. UTC | #6
On Wed, May 16, 2018 at 09:59:01PM +0200, Stefan Wahren wrote:
> Hi Guenter,
> 
> > Guenter Roeck <linux@roeck-us.net> hat am 16. Mai 2018 um 20:21 geschrieben:
> > 
> > 
> > On Wed, May 16, 2018 at 03:37:04PM +0200, Stefan Wahren wrote:
> > > Currently there is no easy way to detect under-voltage conditions on a remote
> > > Raspberry Pi. This hwmon driver retrieves the state of the under-voltage sensor
> > > via mailbox interface. The handling based on Noralf's modifications to the
> > > downstream firmware driver. In case of an under-voltage condition only an entry
> > > is written to the kernel log.
> > > 
> > 
> > My major concern is how this is displayed with the 'sensors' command.
> > Can you test and report ?
> 
> I get the following output:
> rpi_volt-isa-0000
> Adapter: ISA adapter
> in0:              N/A  
> 
Ok, that works.

> > 
> > Of course, it would be much better if the firmware would also report
> > the actual voltage, but I guess we can't have everything.
> 
> I think this isn't possible because the hardware only provide a binary value (GPIO).
> 
> > 
> > More comments inline.
> > 
> > Thanks,
> > Guenter
> > 
> > > CC: "Noralf Trønnes" <noralf@tronnes.org>
> > > Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
> > > ---
> > >  drivers/hwmon/Kconfig             |  10 ++
> > >  drivers/hwmon/Makefile            |   1 +
> > >  drivers/hwmon/raspberrypi-hwmon.c | 207 ++++++++++++++++++++++++++++++++++++++
> > 
> > Please also provide Documentation/hwmon/raspberrypi-hwmon.
> > 
> > >  3 files changed, 218 insertions(+)
> > >  create mode 100644 drivers/hwmon/raspberrypi-hwmon.c
> > > 
> > > diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> > > index 768aed5..7f935cf 100644
> > > --- a/drivers/hwmon/Kconfig
> > > +++ b/drivers/hwmon/Kconfig
> > > @@ -1298,6 +1298,16 @@ config SENSORS_PWM_FAN
> > >  	  This driver can also be built as a module.  If so, the module
> > >  	  will be called pwm-fan.
> > >  
> > > +config SENSORS_RASPBERRYPI_HWMON
> > > +	tristate "Raspberry Pi voltage monitor"
> > > +	depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
> > > +	help
> > > +	  If you say yes here you get support for voltage sensor on the
> > > +	  Raspberry Pi.
> > > +
> > > +	  This driver can also be built as a module. If so, the module
> > > +	  will be called raspberrypi-hwmon.
> > > +
> > >  config SENSORS_SHT15
> > >  	tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
> > >  	depends on GPIOLIB || COMPILE_TEST
> > > diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> > > index e7d52a3..a929770 100644
> > > --- a/drivers/hwmon/Makefile
> > > +++ b/drivers/hwmon/Makefile
> > > @@ -141,6 +141,7 @@ obj-$(CONFIG_SENSORS_PC87427)	+= pc87427.o
> > >  obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
> > >  obj-$(CONFIG_SENSORS_POWR1220)  += powr1220.o
> > >  obj-$(CONFIG_SENSORS_PWM_FAN)	+= pwm-fan.o
> > > +obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON)	+= raspberrypi-hwmon.o
> > >  obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
> > >  obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
> > >  obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
> > > diff --git a/drivers/hwmon/raspberrypi-hwmon.c b/drivers/hwmon/raspberrypi-hwmon.c
> > > new file mode 100644
> > > index 0000000..2003f6c
> > > --- /dev/null
> > > +++ b/drivers/hwmon/raspberrypi-hwmon.c
> > > @@ -0,0 +1,207 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Raspberry Pi voltage sensor driver
> > > + *
> > > + * Based on firmware/raspberrypi.c by Noralf Trønnes
> > > + *
> > > + * Copyright (C) 2018 Stefan Wahren <stefan.wahren@i2se.com>
> > > + */
> > > +#include <linux/device.h>
> > > +#include <linux/err.h>
> > > +#include <linux/hwmon.h>
> > > +#include <linux/hwmon-sysfs.h>
> > 
> > Unnecessary include
> > 
> > > +#include <linux/module.h>
> > > +#include <linux/of_device.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/slab.h>
> > > +#include <linux/workqueue.h>
> > > +#include <soc/bcm2835/raspberrypi-firmware.h>
> > > +
> > > +#define UNDERVOLTAGE_STICKY_BIT	BIT(16)
> > > +
> > > +struct rpi_hwmon_data {
> > > +	struct device *hwmon_dev;
> > > +	struct rpi_firmware *fw;
> > > +	u32 last_throttled;
> > > +	struct delayed_work get_values_poll_work;
> > > +};
> > > +
> > > +static void rpi_firmware_get_throttled(struct rpi_hwmon_data *data)
> > > +{
> > > +	u32 new_uv, old_uv, value;
> > > +	int ret;
> > > +
> > > +	/* Clear sticky bits */
> > 
> > Please make more explicit that this is a request/command sent to the firmware.
> > 
> > > +	value = 0xffff;
> > > +
> > > +	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> > > +				    &value, sizeof(value));
> > > +	if (ret) {
> > > +		dev_err_once(data->hwmon_dev, "%s: Failed to get throttled (%d)\n",
> > > +			     __func__, ret);
> > 
> > The function name seems unnecessary.
> > 
> > > +		return;
> > > +	}
> > > +
> > > +	new_uv = value & UNDERVOLTAGE_STICKY_BIT;
> > > +	old_uv = data->last_throttled & UNDERVOLTAGE_STICKY_BIT;
> > > +	data->last_throttled = value;
> > > +
> > > +	if (new_uv == old_uv)
> > > +		return;
> > > +
> > > +	if (new_uv)
> > > +		dev_crit(data->hwmon_dev, "Under-voltage detected! (0x%08x)\n",
> > > +			 value);
> > > +	else
> > > +		dev_info(data->hwmon_dev, "Voltage normalised (0x%08x)\n",
> > > +			 value);
> > 
> > What value do those hex values provide to the user ?
> 
> The actual definition of the bits can be found in the commit log of patch #1. But this isn't very helpful for an end user.
> 
I would suggest to drop the value from the log.

> > 
> > > +
> > > +	sysfs_notify(&data->hwmon_dev->kobj, NULL, "in0_lcrit_alarm");
> > > +}
> > > +
> > > +static void get_values_poll(struct work_struct *work)
> > > +{
> > > +	struct rpi_hwmon_data *data;
> > > +
> > > +	data = container_of(work, struct rpi_hwmon_data,
> > > +			    get_values_poll_work.work);
> > > +
> > > +	rpi_firmware_get_throttled(data);
> > > +
> > > +	/*
> > > +	 * We can't run faster than the sticky shift (100ms) since we get
> > > +	 * flipping in the sticky bits that are cleared.
> > > +	 */
> > > +	schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> > > +}
> > > +
> > > +static int rpi_read(struct device *dev, enum hwmon_sensor_types type,
> > > +		    u32 attr, int channel, long *val)
> > > +{
> > > +	struct rpi_hwmon_data *data = dev_get_drvdata(dev);
> > > +
> > > +	if (type != hwmon_in)
> > > +		return -EOPNOTSUPP;
> > > +
> > > +	if (attr != hwmon_in_lcrit_alarm)
> > > +		return -EOPNOTSUPP;
> > > +
> > > +	if (channel)
> > > +		return -EOPNOTSUPP;
> > > +
> > There is only one channel, one attribute, and one type supported.
> > As such, the checks are unnecessary.
> > 
> > > +	*val = !!(data->last_throttled & UNDERVOLTAGE_STICKY_BIT);
> > > +	return 0;
> > > +}
> > > +
> > > +static umode_t rpi_is_visible(const void *_data, enum hwmon_sensor_types type,
> > > +			      u32 attr, int channel)
> > > +{
> > > +	if (type != hwmon_in)
> > > +		return 0;
> > > +
> > > +	if (attr != hwmon_in_lcrit_alarm)
> > > +		return 0;
> > > +
> > > +	if (channel)
> > > +		return 0;
> > 
> > Same as above. In the list below, there is not a single conditional attribute.
> > Given that, the checks should be unnecessary, and it should be sufficient to
> > just return 0444.
> > 
> > > +
> > > +	return 0444;
> > > +}
> > > +
> > > +static const u32 rpi_in_config[] = {
> > > +	HWMON_I_LCRIT_ALARM,
> > > +	0
> > > +};
> > > +
> > > +static const struct hwmon_channel_info rpi_in = {
> > > +	.type = hwmon_in,
> > > +	.config = rpi_in_config,
> > > +};
> > > +
> > > +static const struct hwmon_channel_info *rpi_info[] = {
> > > +	&rpi_in,
> > > +	NULL
> > > +};
> > > +
> > > +static const struct hwmon_ops rpi_hwmon_ops = {
> > > +	.is_visible = rpi_is_visible,
> > > +	.read = rpi_read,
> > > +};
> > > +
> > > +static const struct hwmon_chip_info rpi_chip_info = {
> > > +	.ops = &rpi_hwmon_ops,
> > > +	.info = rpi_info,
> > > +};
> > > +
> > > +static int rpi_hwmon_probe(struct platform_device *pdev)
> > > +{
> > > +	struct device *dev = &pdev->dev;
> > > +	struct device_node *fw_node;
> > > +	struct rpi_hwmon_data *data;
> > > +	int ret;
> > > +
> > > +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> > > +	if (!data)
> > > +		return -ENOMEM;
> > > +
> > > +	fw_node = of_get_parent(dev->of_node);
> > > +	if (!fw_node) {
> > > +		dev_err(dev, "Missing firmware node\n");
> > > +		return -ENOENT;
> > > +	}
> > > +
> > > +	data->fw = rpi_firmware_get(fw_node);
> > > +	of_node_put(fw_node);
> > > +	if (!data->fw)
> > > +		return -EPROBE_DEFER;
> > > +
> > > +	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
> > > +				    &data->last_throttled,
> > > +				    sizeof(data->last_throttled));
> > > +	if (ret) {
> > > +		dev_info(dev, "Firmware doesn't support GET_THROTTLED\n");
> > 
> > If this is an error -> dev_err().
> 
> I wasn't sure. If the firmware is too old, we cannot provide this feature and it's a waste of resources to load this driver. On the other side i don't want to confuse people this is something bad.
> 
Then I would suggest to return -ENODEV.

Guenter

> Stefan
> 
> > 
> > > +		return -EOPNOTSUPP;
> > 
> > or return -ENODEV.
> > 
> > > +	}
> > > +
> > > +	data->hwmon_dev = devm_hwmon_device_register_with_info(dev, "rpi_volt",
> > > +							       data,
> > > +							       &rpi_chip_info,
> > > +							       NULL);
> > > +
> > > +	INIT_DELAYED_WORK(&data->get_values_poll_work, get_values_poll);
> > > +	platform_set_drvdata(pdev, data);
> > > +
> > > +	if (!PTR_ERR_OR_ZERO(data->hwmon_dev))
> > > +		schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
> > > +
> > > +	return PTR_ERR_OR_ZERO(data->hwmon_dev);
> > > +}
> > > +
> > > +static int rpi_hwmon_remove(struct platform_device *pdev)
> > > +{
> > > +	struct rpi_hwmon_data *data = platform_get_drvdata(pdev);
> > > +
> > > +	cancel_delayed_work_sync(&data->get_values_poll_work);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static const struct of_device_id rpi_hwmon_of_match[] = {
> > > +	{ .compatible = "raspberrypi,bcm2835-hwmon", },
> > > +	{ /* sentinel */},
> > > +};
> > > +MODULE_DEVICE_TABLE(of, rpi_hwmon_of_match);
> > > +
> > > +static struct platform_driver rpi_hwmon_driver = {
> > > +	.probe = rpi_hwmon_probe,
> > > +	.remove = rpi_hwmon_remove,
> > > +	.driver = {
> > > +		.name = "raspberrypi-hwmon",
> > > +		.of_match_table = rpi_hwmon_of_match,
> > > +	},
> > > +};
> > > +module_platform_driver(rpi_hwmon_driver);
> > > +
> > > +MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
> > > +MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
> > > +MODULE_LICENSE("GPL v2");
> > > -- 
> > > 2.7.4
> > > 
> > > --
> > > To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in
> > > the body of a message to majordomo@vger.kernel.org
> > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > 
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Eric Anholt May 17, 2018, 5:25 p.m. UTC | #7
Guenter Roeck <linux@roeck-us.net> writes:

> On Wed, May 16, 2018 at 09:59:01PM +0200, Stefan Wahren wrote:
>> Hi Guenter,
>> 
>> > Guenter Roeck <linux@roeck-us.net> hat am 16. Mai 2018 um 20:21 geschrieben:
>> > 
>> > 
>> > On Wed, May 16, 2018 at 03:37:04PM +0200, Stefan Wahren wrote:
>> > > Currently there is no easy way to detect under-voltage conditions on a remote
>> > > Raspberry Pi. This hwmon driver retrieves the state of the under-voltage sensor
>> > > via mailbox interface. The handling based on Noralf's modifications to the
>> > > downstream firmware driver. In case of an under-voltage condition only an entry
>> > > is written to the kernel log.
>> > > 
>> > 
>> > My major concern is how this is displayed with the 'sensors' command.
>> > Can you test and report ?
>> 
>> I get the following output:
>> rpi_volt-isa-0000
>> Adapter: ISA adapter
>> in0:              N/A  
>> 
> Ok, that works.

Thanks for the quick review on this, Guenter!  This driver is going to
help save a lot of people debugging time on rpis in the upstream kernel.
diff mbox

Patch

diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 768aed5..7f935cf 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1298,6 +1298,16 @@  config SENSORS_PWM_FAN
 	  This driver can also be built as a module.  If so, the module
 	  will be called pwm-fan.
 
+config SENSORS_RASPBERRYPI_HWMON
+	tristate "Raspberry Pi voltage monitor"
+	depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
+	help
+	  If you say yes here you get support for voltage sensor on the
+	  Raspberry Pi.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called raspberrypi-hwmon.
+
 config SENSORS_SHT15
 	tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
 	depends on GPIOLIB || COMPILE_TEST
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index e7d52a3..a929770 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -141,6 +141,7 @@  obj-$(CONFIG_SENSORS_PC87427)	+= pc87427.o
 obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
 obj-$(CONFIG_SENSORS_POWR1220)  += powr1220.o
 obj-$(CONFIG_SENSORS_PWM_FAN)	+= pwm-fan.o
+obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON)	+= raspberrypi-hwmon.o
 obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
 obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
 obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
diff --git a/drivers/hwmon/raspberrypi-hwmon.c b/drivers/hwmon/raspberrypi-hwmon.c
new file mode 100644
index 0000000..2003f6c
--- /dev/null
+++ b/drivers/hwmon/raspberrypi-hwmon.c
@@ -0,0 +1,207 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Raspberry Pi voltage sensor driver
+ *
+ * Based on firmware/raspberrypi.c by Noralf Trønnes
+ *
+ * Copyright (C) 2018 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+#include <soc/bcm2835/raspberrypi-firmware.h>
+
+#define UNDERVOLTAGE_STICKY_BIT	BIT(16)
+
+struct rpi_hwmon_data {
+	struct device *hwmon_dev;
+	struct rpi_firmware *fw;
+	u32 last_throttled;
+	struct delayed_work get_values_poll_work;
+};
+
+static void rpi_firmware_get_throttled(struct rpi_hwmon_data *data)
+{
+	u32 new_uv, old_uv, value;
+	int ret;
+
+	/* Clear sticky bits */
+	value = 0xffff;
+
+	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
+				    &value, sizeof(value));
+	if (ret) {
+		dev_err_once(data->hwmon_dev, "%s: Failed to get throttled (%d)\n",
+			     __func__, ret);
+		return;
+	}
+
+	new_uv = value & UNDERVOLTAGE_STICKY_BIT;
+	old_uv = data->last_throttled & UNDERVOLTAGE_STICKY_BIT;
+	data->last_throttled = value;
+
+	if (new_uv == old_uv)
+		return;
+
+	if (new_uv)
+		dev_crit(data->hwmon_dev, "Under-voltage detected! (0x%08x)\n",
+			 value);
+	else
+		dev_info(data->hwmon_dev, "Voltage normalised (0x%08x)\n",
+			 value);
+
+	sysfs_notify(&data->hwmon_dev->kobj, NULL, "in0_lcrit_alarm");
+}
+
+static void get_values_poll(struct work_struct *work)
+{
+	struct rpi_hwmon_data *data;
+
+	data = container_of(work, struct rpi_hwmon_data,
+			    get_values_poll_work.work);
+
+	rpi_firmware_get_throttled(data);
+
+	/*
+	 * We can't run faster than the sticky shift (100ms) since we get
+	 * flipping in the sticky bits that are cleared.
+	 */
+	schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
+}
+
+static int rpi_read(struct device *dev, enum hwmon_sensor_types type,
+		    u32 attr, int channel, long *val)
+{
+	struct rpi_hwmon_data *data = dev_get_drvdata(dev);
+
+	if (type != hwmon_in)
+		return -EOPNOTSUPP;
+
+	if (attr != hwmon_in_lcrit_alarm)
+		return -EOPNOTSUPP;
+
+	if (channel)
+		return -EOPNOTSUPP;
+
+	*val = !!(data->last_throttled & UNDERVOLTAGE_STICKY_BIT);
+	return 0;
+}
+
+static umode_t rpi_is_visible(const void *_data, enum hwmon_sensor_types type,
+			      u32 attr, int channel)
+{
+	if (type != hwmon_in)
+		return 0;
+
+	if (attr != hwmon_in_lcrit_alarm)
+		return 0;
+
+	if (channel)
+		return 0;
+
+	return 0444;
+}
+
+static const u32 rpi_in_config[] = {
+	HWMON_I_LCRIT_ALARM,
+	0
+};
+
+static const struct hwmon_channel_info rpi_in = {
+	.type = hwmon_in,
+	.config = rpi_in_config,
+};
+
+static const struct hwmon_channel_info *rpi_info[] = {
+	&rpi_in,
+	NULL
+};
+
+static const struct hwmon_ops rpi_hwmon_ops = {
+	.is_visible = rpi_is_visible,
+	.read = rpi_read,
+};
+
+static const struct hwmon_chip_info rpi_chip_info = {
+	.ops = &rpi_hwmon_ops,
+	.info = rpi_info,
+};
+
+static int rpi_hwmon_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *fw_node;
+	struct rpi_hwmon_data *data;
+	int ret;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	fw_node = of_get_parent(dev->of_node);
+	if (!fw_node) {
+		dev_err(dev, "Missing firmware node\n");
+		return -ENOENT;
+	}
+
+	data->fw = rpi_firmware_get(fw_node);
+	of_node_put(fw_node);
+	if (!data->fw)
+		return -EPROBE_DEFER;
+
+	ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
+				    &data->last_throttled,
+				    sizeof(data->last_throttled));
+	if (ret) {
+		dev_info(dev, "Firmware doesn't support GET_THROTTLED\n");
+		return -EOPNOTSUPP;
+	}
+
+	data->hwmon_dev = devm_hwmon_device_register_with_info(dev, "rpi_volt",
+							       data,
+							       &rpi_chip_info,
+							       NULL);
+
+	INIT_DELAYED_WORK(&data->get_values_poll_work, get_values_poll);
+	platform_set_drvdata(pdev, data);
+
+	if (!PTR_ERR_OR_ZERO(data->hwmon_dev))
+		schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
+
+	return PTR_ERR_OR_ZERO(data->hwmon_dev);
+}
+
+static int rpi_hwmon_remove(struct platform_device *pdev)
+{
+	struct rpi_hwmon_data *data = platform_get_drvdata(pdev);
+
+	cancel_delayed_work_sync(&data->get_values_poll_work);
+
+	return 0;
+}
+
+static const struct of_device_id rpi_hwmon_of_match[] = {
+	{ .compatible = "raspberrypi,bcm2835-hwmon", },
+	{ /* sentinel */},
+};
+MODULE_DEVICE_TABLE(of, rpi_hwmon_of_match);
+
+static struct platform_driver rpi_hwmon_driver = {
+	.probe = rpi_hwmon_probe,
+	.remove = rpi_hwmon_remove,
+	.driver = {
+		.name = "raspberrypi-hwmon",
+		.of_match_table = rpi_hwmon_of_match,
+	},
+};
+module_platform_driver(rpi_hwmon_driver);
+
+MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
+MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
+MODULE_LICENSE("GPL v2");