Message ID | 20180524160051.29966-6-bgodavar@codeaurora.org (mailing list archive) |
---|---|
State | Superseded, archived |
Delegated to: | Andy Gross |
Headers | show |
Hi Balakrishna, Thank you for the patch! Perhaps something to improve: [auto build test WARNING on bluetooth-next/master] [cannot apply to bluetooth/master v4.17-rc6] [if your patch is applied to the wrong git tree, please drop us a note to help improve the system] url: https://github.com/0day-ci/linux/commits/Balakrishna-Godavarthi/Enable-Bluetooth-functionality-for-WCN3990/20180527-135618 base: https://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next.git master config: x86_64-randconfig-x005-201821 (attached as .config) compiler: gcc-7 (Debian 7.3.0-16) 7.3.0 reproduce: # save the attached .config to linux build tree make ARCH=x86_64 All warnings (new ones prefixed by >>): In file included from drivers/bluetooth/btqca.c:26:0: >> drivers/bluetooth/btqca.h:130:34: warning: 'struct hci_uart' declared inside parameter list will not be visible outside of this definition or declaration int qca_btsoc_power_setup(struct hci_uart *hu, bool on); ^~~~~~~~ vim +130 drivers/bluetooth/btqca.h 129 > 130 int qca_btsoc_power_setup(struct hci_uart *hu, bool on); 131 int qca_btsoc_shutdown(struct hci_dev *hdev); 132 --- 0-DAY kernel test infrastructure Open Source Technology Center https://lists.01.org/pipermail/kbuild-all Intel Corporation
Hi Balakrishna, Thank you for the patch! Perhaps something to improve: [auto build test WARNING on bluetooth-next/master] [cannot apply to bluetooth/master v4.17-rc6] [if your patch is applied to the wrong git tree, please drop us a note to help improve the system] url: https://github.com/0day-ci/linux/commits/Balakrishna-Godavarthi/Enable-Bluetooth-functionality-for-WCN3990/20180527-135618 base: https://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next.git master config: i386-randconfig-b0-05271406 (attached as .config) compiler: gcc-4.9 (Debian 4.9.4-2) 4.9.4 reproduce: # save the attached .config to linux build tree make ARCH=i386 All warnings (new ones prefixed by >>): In file included from drivers/bluetooth/btqca.c:26:0: >> drivers/bluetooth/btqca.h:130:34: warning: 'struct hci_uart' declared inside parameter list int qca_btsoc_power_setup(struct hci_uart *hu, bool on); ^ >> drivers/bluetooth/btqca.h:130:34: warning: its scope is only this definition or declaration, which is probably not what you want vim +130 drivers/bluetooth/btqca.h 129 > 130 int qca_btsoc_power_setup(struct hci_uart *hu, bool on); 131 int qca_btsoc_shutdown(struct hci_dev *hdev); 132 --- 0-DAY kernel test infrastructure Open Source Technology Center https://lists.01.org/pipermail/kbuild-all Intel Corporation
On Thu, May 24, 2018 at 09:30:51PM +0530, Balakrishna Godavarthi wrote: > Add support to set voltage/current of various regulators > to power up/down Bluetooth chip wcn3990. > > Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> > --- > > Changes in v6: > * Hooked up qca_power to qca_serdev. > * renamed all the naming inconsistency functions with qca_* > * leveraged common code of ROME for wcn3990. > * created wrapper functions for re-usable blocks. > * updated function of _*regulator_enable and _*regualtor_disable. > * removed redundant comments and functions. > * addressed review comments. > > Changes in v5: > * updated regulator vddpa min_uV to 1304000. > * addressed review comments. > > Changes in v4: > * Segregated the changes of btqca from hci_qca > * rebased all changes on top of bluetooth-next. > * addressed review comments. > --- > > ... > > diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c > index cb1034998040..e235be0e5202 100644 > --- a/drivers/bluetooth/hci_qca.c > +++ b/drivers/bluetooth/hci_qca.c > ... > +static void qca_set_init_speed(struct hci_uart *hu) > +{ > + unsigned int speed = 0; > > - /* Setup initial baudrate */ > - speed = 0; > if (hu->init_speed) > speed = hu->init_speed; > else if (hu->proto->init_speed) > @@ -946,29 +1015,136 @@ static int qca_setup(struct hci_uart *hu) > > if (speed) > host_set_baudrate(hu, speed); > +} > + > +static int qca_set_operating_speed(struct hci_uart *hu, u32 *qca_baudrate) > +{ This is a bit convoluted, with the function setting the speed and returning it. I would suggest a qca_get_oper_speed() and qca_get_init_speed(), and just have them return the value instead of passing it through a pointer. You could then have a qca_set_speed() which converts the baudrate to the value the chip understands, calls qca_set_baudrate() and host_set_baudrate() > +static int qca_setup(struct hci_uart *hu) > +{ > + struct hci_dev *hdev = hu->hdev; > + struct qca_data *qca = hu->priv; > + struct qca_serdev *qcadev; > + unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200; > + int ret; > + int soc_ver; > + > + qcadev = serdev_device_get_drvdata(hu->serdev); > + > + switch (qcadev->btsoc_type) { > + case BTQCA_CHEROKEE: > + bt_dev_dbg(hdev, "setting up wcn3990"); > + /* Patch downloading has to be done without IBS mode */ > + clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); > + qca_set_init_speed(hu); > + hci_uart_set_flow_control(hu, true); > + ret = qca_send_vendor_cmd(hdev, CHEROKEE_POWERON_PULSE); > + if (ret) { > + bt_dev_err(hdev, "failed to send power on command"); > + return ret; > + } > + > + /* Close and re-open the port */ As mentioned earlier, this comment doesn't provide any useful information, it's evident from the code. Rather explain *why* the close/open is needed. > + serdev_device_close(hu->serdev); > + ret = serdev_device_open(hu->serdev); > + if (ret) { > + bt_dev_err(hdev, "failed to open port"); > + return ret; > + } > + > + qca_set_init_speed(hu); > + hci_uart_set_flow_control(hu, false); > + msleep(100); Which step makes the delay necessary? I guess it's not enabling flow control but probably sending the power on command. If that is correct the delay should be done after the corresponding command. > + ret = qca_patch_ver_req(hdev, &soc_ver); > + if (ret < 0 || soc_ver == 0) { > + bt_dev_err(hdev, "Failed to get version 0x%x", ret); Probably better: "Failed to get version: %d" since ret contains an errno and the problem wasn't that we couldn't get "version 0x<errno>". > + return ret; > + } > + > + bt_dev_info(hdev, "wcn3990 controller version 0x%08x", soc_ver); > + hci_uart_set_flow_control(hu, true); Repeatedly switching on and off of flow control is a bit noisy, I wonder if it could be hidden in a wrapper. From the code it seems that flow control is disabled (true) for init speed and and enabled (false) for operating speed. If this is correct the hci_uart_set_flow_control() calls could be moved inside qca_set_oper/init_speed(). struct qca_serdev could have a flag indicating if flow control is supported at all to skip the hci_uart_set_flow_control() calls for Rome. Just an idea, no objections if you prefer to leave it as is and Marcel is ok with it. > + ret = qca_set_operating_speed(hu, &qca_baudrate); > + if (ret) > + return ret; > + hci_uart_set_flow_control(hu, false); > + /* Setup patch and NVM configurations */ > + ret = qca_uart_setup_cherokee(hdev, qca_baudrate, &soc_ver); > + > + break; > + > + default: > + bt_dev_info(hdev, "ROME setup"); > + > + /* Patch downloading has to be done without IBS mode */ > + clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); > + > + /* Setup initial baudrate */ > + speed = 0; > + if (hu->init_speed) > + speed = hu->init_speed; > + else if (hu->proto->init_speed) > + speed = hu->proto->init_speed; If you introduce helpers to determine the init/oper speed these should also be used here. Probably best to do this in a separate patch. > + > + if (speed) > + host_set_baudrate(hu, speed); > + > + /* Setup user speed if needed */ > + speed = 0; > + if (hu->oper_speed) > + speed = hu->oper_speed; > + else if (hu->proto->oper_speed) > + speed = hu->proto->oper_speed; ditto > +static void qca_disable_regulator(struct qca_vreg vregs, > + struct regulator *regulator) > +{ > + /* Disable the regulator if requested by user > + * or when fault to enable any regulator. > + */ This comment is not useful. The following code simply disables the regulator, why this is done is a question of the caller. > + regulator_disable(regulator); > + regulator_set_voltage(regulator, 0, vregs.max_uV); > + if (vregs.load_uA) > + regulator_set_load(regulator, 0); > + > +} > + > +int qca_btsoc_power_setup(struct hci_uart *hu, bool on) > +{ > + struct qca_vreg *vregs; > + struct regulator_bulk_data *vreg_bulk; > + struct qca_serdev *qcadev; > + int i, num_vregs, ret = 0; > + > + qcadev = serdev_device_get_drvdata(hu->serdev); > + if (!qcadev || !qcadev->bt_power || !qcadev->bt_power->vreg_data || > + !qcadev->bt_power->vreg_bulk) > + return -EINVAL; > + > + vregs = qcadev->bt_power->vreg_data->vregs; > + vreg_bulk = qcadev->bt_power->vreg_bulk; > + num_vregs = qcadev->bt_power->vreg_data->num_vregs; > + BT_DBG("on: %d", on); > + if (on && !qcadev->bt_power->vregs_on) { > + for (i = 0; i < num_vregs; i++) { > + ret = qca_enable_regulator(vregs[i], > + vreg_bulk[i].consumer); > + if (ret) > + break; > + } > + /* regulators failed */ Comment is not useful, BT_ERR below leaves things clear. > + if (ret) { > + BT_ERR("failed to enable regulator:%s", vregs[i].name); > + /* turn off regulators which are enabled */ > + for (i = i - 1; i >= 0; i--) > + qca_disable_regulator(vregs[i], > + vreg_bulk[i].consumer); > + } else { > + qcadev->bt_power->vregs_on = true; > + } > + } else if (!on && qcadev->bt_power->vregs_on) { > + /* turn off regulator in reverse order */ > + i = qcadev->bt_power->vreg_data->num_vregs - 1; > + for ( ; i >= 0; i--) > + qca_disable_regulator(vregs[i], vreg_bulk[i].consumer); > + qcadev->bt_power->vregs_on = false; > + } > + > + return ret; > +} > + > +static int qca_init_regulators(struct qca_power *qca, > + const struct qca_vreg *vregs, size_t num_vregs) > +{ > + int i; > + > + qca->vreg_bulk = devm_kzalloc(qca->dev, num_vregs * > + sizeof(struct regulator_bulk_data), > + GFP_KERNEL); > + if (!qca->vreg_bulk) > + return -ENOMEM; > + > + for (i = 0; i < num_vregs; i++) > + qca->vreg_bulk[i].supply = vregs[i].name; > + > + return devm_regulator_bulk_get(qca->dev, num_vregs, qca->vreg_bulk); > +} > + > static int qca_serdev_probe(struct serdev_device *serdev) > { > struct qca_serdev *qcadev; > + const struct qca_vreg_data *data; > int err; > > qcadev = devm_kzalloc(&serdev->dev, sizeof(*qcadev), GFP_KERNEL); > @@ -1014,34 +1301,72 @@ static int qca_serdev_probe(struct serdev_device *serdev) > return -ENOMEM; > > qcadev->serdev_hu.serdev = serdev; > + data = of_device_get_match_data(&serdev->dev); > + if (data && data->soc_type == BTQCA_CHEROKEE) > + qcadev->btsoc_type = BTQCA_CHEROKEE; > + else > + qcadev->btsoc_type = BTQCA_ROME; > + > serdev_device_set_drvdata(serdev, qcadev); > + if (qcadev->btsoc_type == BTQCA_CHEROKEE) { > + qcadev->bt_power = devm_kzalloc(&serdev->dev, > + sizeof(struct qca_power), > + GFP_KERNEL); > + if (!qcadev->bt_power) > + return -ENOMEM; > + > + qcadev->bt_power->dev = &serdev->dev; > + qcadev->bt_power->vreg_data = data; > + err = qca_init_regulators(qcadev->bt_power, data->vregs, > + data->num_vregs); > + if (err) { > + BT_ERR("Failed to init regulators:%d", err); > + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); > + devm_kfree(&serdev->dev, qcadev->bt_power); Not necessary, the memory is allocated with devm_kzalloc(&serdev->dev, ...), therefore it is freed if probe() fails. > + goto out; > + } > > - qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable", > - GPIOD_OUT_LOW); > - if (IS_ERR(qcadev->bt_en)) { > - dev_err(&serdev->dev, "failed to acquire enable gpio\n"); > - return PTR_ERR(qcadev->bt_en); > - } > + qcadev->bt_power->vregs_on = false; > + device_property_read_u32(&serdev->dev, "max-speed", > + &qcadev->oper_speed); > + if (!qcadev->oper_speed) > + BT_INFO("UART will pick default operating speed"); > + err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); > + if (err) { > + BT_ERR("wcn3990 serdev registration failed"); > + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); > + devm_kfree(&serdev->dev, qcadev->bt_power); no need to free memory. > + goto out; > + } > + } else { > + qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable", > + GPIOD_OUT_LOW); > + if (IS_ERR(qcadev->bt_en)) { > + dev_err(&serdev->dev, "failed to acquire enable gpio\n"); > + return PTR_ERR(qcadev->bt_en); > + } > > - qcadev->susclk = devm_clk_get(&serdev->dev, NULL); > - if (IS_ERR(qcadev->susclk)) { > - dev_err(&serdev->dev, "failed to acquire clk\n"); > - return PTR_ERR(qcadev->susclk); > - } > + qcadev->susclk = devm_clk_get(&serdev->dev, NULL); > + if (IS_ERR(qcadev->susclk)) { > + dev_err(&serdev->dev, "failed to acquire clk\n"); > + return PTR_ERR(qcadev->susclk); > + } > > - err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ); > - if (err) > - return err; > + err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ); > + if (err) > + return err; > > - err = clk_prepare_enable(qcadev->susclk); > - if (err) > - return err; > + err = clk_prepare_enable(qcadev->susclk); > + if (err) > + return err; > > - err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); > - if (err) > - clk_disable_unprepare(qcadev->susclk); > + err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); > + if (err) > + clk_disable_unprepare(qcadev->susclk); > + } > + > +out: return err; > > - return err; > } > > static void qca_serdev_remove(struct serdev_device *serdev) > @@ -1050,11 +1375,17 @@ static void qca_serdev_remove(struct serdev_device *serdev) > > hci_uart_unregister_device(&qcadev->serdev_hu); > > - clk_disable_unprepare(qcadev->susclk); > + if (qcadev->btsoc_type == BTQCA_CHEROKEE) { > + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); > + devm_kfree(&serdev->dev, qcadev->bt_power); no need to free memory -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
HI Matthias, Pls find my comments inline. On 2018-05-29 23:11, Matthias Kaehlcke wrote: > On Thu, May 24, 2018 at 09:30:51PM +0530, Balakrishna Godavarthi wrote: >> Add support to set voltage/current of various regulators >> to power up/down Bluetooth chip wcn3990. >> >> Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> >> --- >> >> Changes in v6: >> * Hooked up qca_power to qca_serdev. >> * renamed all the naming inconsistency functions with qca_* >> * leveraged common code of ROME for wcn3990. >> * created wrapper functions for re-usable blocks. >> * updated function of _*regulator_enable and _*regualtor_disable. >> * removed redundant comments and functions. >> * addressed review comments. >> >> Changes in v5: >> * updated regulator vddpa min_uV to 1304000. >> * addressed review comments. >> >> Changes in v4: >> * Segregated the changes of btqca from hci_qca >> * rebased all changes on top of bluetooth-next. >> * addressed review comments. >> --- >> >> ... >> >> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c >> index cb1034998040..e235be0e5202 100644 >> --- a/drivers/bluetooth/hci_qca.c >> +++ b/drivers/bluetooth/hci_qca.c >> ... >> +static void qca_set_init_speed(struct hci_uart *hu) >> +{ >> + unsigned int speed = 0; >> >> - /* Setup initial baudrate */ >> - speed = 0; >> if (hu->init_speed) >> speed = hu->init_speed; >> else if (hu->proto->init_speed) >> @@ -946,29 +1015,136 @@ static int qca_setup(struct hci_uart *hu) >> >> if (speed) >> host_set_baudrate(hu, speed); >> +} >> + >> +static int qca_set_operating_speed(struct hci_uart *hu, u32 >> *qca_baudrate) >> +{ > > This is a bit convoluted, with the function setting the speed and > returning it. I would suggest a qca_get_oper_speed() and > qca_get_init_speed(), and just have them return the value instead of > passing it through a pointer. You could then have a qca_set_speed() > which converts the baudrate to the value the chip understands, calls > qca_set_baudrate() and host_set_baudrate() > [Bala]: will update. >> +static int qca_setup(struct hci_uart *hu) >> +{ >> + struct hci_dev *hdev = hu->hdev; >> + struct qca_data *qca = hu->priv; >> + struct qca_serdev *qcadev; >> + unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200; >> + int ret; >> + int soc_ver; >> + >> + qcadev = serdev_device_get_drvdata(hu->serdev); >> + >> + switch (qcadev->btsoc_type) { >> + case BTQCA_CHEROKEE: >> + bt_dev_dbg(hdev, "setting up wcn3990"); >> + /* Patch downloading has to be done without IBS mode */ >> + clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); >> + qca_set_init_speed(hu); >> + hci_uart_set_flow_control(hu, true); >> + ret = qca_send_vendor_cmd(hdev, CHEROKEE_POWERON_PULSE); >> + if (ret) { >> + bt_dev_err(hdev, "failed to send power on command"); >> + return ret; >> + } >> + >> + /* Close and re-open the port */ > > As mentioned earlier, this comment doesn't provide any useful > information, it's evident from the code. Rather explain *why* the > close/open is needed. > >> + serdev_device_close(hu->serdev); >> + ret = serdev_device_open(hu->serdev); >> + if (ret) { >> + bt_dev_err(hdev, "failed to open port"); >> + return ret; >> + } >> + >> + qca_set_init_speed(hu); >> + hci_uart_set_flow_control(hu, false); >> + msleep(100); > > Which step makes the delay necessary? I guess it's not enabling flow > control but probably sending the power on command. If that is correct > the delay should be done after the corresponding command. > >> + ret = qca_patch_ver_req(hdev, &soc_ver); >> + if (ret < 0 || soc_ver == 0) { >> + bt_dev_err(hdev, "Failed to get version 0x%x", ret); > > Probably better: "Failed to get version: %d" since ret contains an > errno and the problem wasn't that we couldn't get "version 0x<errno>". > >> + return ret; >> + } >> + >> + bt_dev_info(hdev, "wcn3990 controller version 0x%08x", soc_ver); >> + hci_uart_set_flow_control(hu, true); > > Repeatedly switching on and off of flow control is a bit noisy, I > wonder if it could be hidden in a wrapper. From the code it seems that > flow control is disabled (true) for init speed and and enabled (false) > for operating speed. If this is correct the hci_uart_set_flow_control() > calls could be moved inside qca_set_oper/init_speed(). struct > qca_serdev > could have a flag indicating if flow control is supported at all to > skip the hci_uart_set_flow_control() calls for Rome. > > Just an idea, no objections if you prefer to leave it as is and Marcel > is ok with it. > [Bala]: will update. >> + ret = qca_set_operating_speed(hu, &qca_baudrate); >> + if (ret) >> + return ret; >> + hci_uart_set_flow_control(hu, false); >> + /* Setup patch and NVM configurations */ >> + ret = qca_uart_setup_cherokee(hdev, qca_baudrate, &soc_ver); >> + >> + break; >> + >> + default: >> + bt_dev_info(hdev, "ROME setup"); >> + >> + /* Patch downloading has to be done without IBS mode */ >> + clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); >> + >> + /* Setup initial baudrate */ >> + speed = 0; >> + if (hu->init_speed) >> + speed = hu->init_speed; >> + else if (hu->proto->init_speed) >> + speed = hu->proto->init_speed; > > If you introduce helpers to determine the init/oper speed these should > also be used here. Probably best to do this in a separate patch. > [Bala]: will update ROME related stuff in other patch. >> + >> + if (speed) >> + host_set_baudrate(hu, speed); >> + >> + /* Setup user speed if needed */ >> + speed = 0; >> + if (hu->oper_speed) >> + speed = hu->oper_speed; >> + else if (hu->proto->oper_speed) >> + speed = hu->proto->oper_speed; > > ditto > [Bala]: will update. >> +static void qca_disable_regulator(struct qca_vreg vregs, >> + struct regulator *regulator) >> +{ >> + /* Disable the regulator if requested by user >> + * or when fault to enable any regulator. >> + */ > > This comment is not useful. The following code simply disables the > regulator, why this is done is a question of the caller. > [Bala]: will update. >> + regulator_disable(regulator); >> + regulator_set_voltage(regulator, 0, vregs.max_uV); >> + if (vregs.load_uA) >> + regulator_set_load(regulator, 0); >> + >> +} >> + >> +int qca_btsoc_power_setup(struct hci_uart *hu, bool on) >> +{ >> + struct qca_vreg *vregs; >> + struct regulator_bulk_data *vreg_bulk; >> + struct qca_serdev *qcadev; >> + int i, num_vregs, ret = 0; >> + >> + qcadev = serdev_device_get_drvdata(hu->serdev); >> + if (!qcadev || !qcadev->bt_power || !qcadev->bt_power->vreg_data || >> + !qcadev->bt_power->vreg_bulk) >> + return -EINVAL; >> + >> + vregs = qcadev->bt_power->vreg_data->vregs; >> + vreg_bulk = qcadev->bt_power->vreg_bulk; >> + num_vregs = qcadev->bt_power->vreg_data->num_vregs; >> + BT_DBG("on: %d", on); >> + if (on && !qcadev->bt_power->vregs_on) { >> + for (i = 0; i < num_vregs; i++) { >> + ret = qca_enable_regulator(vregs[i], >> + vreg_bulk[i].consumer); >> + if (ret) >> + break; >> + } >> + /* regulators failed */ > > Comment is not useful, BT_ERR below leaves things clear. [Bala]: will update. > >> + if (ret) { >> + BT_ERR("failed to enable regulator:%s", vregs[i].name); >> + /* turn off regulators which are enabled */ >> + for (i = i - 1; i >= 0; i--) >> + qca_disable_regulator(vregs[i], >> + vreg_bulk[i].consumer); >> + } else { >> + qcadev->bt_power->vregs_on = true; >> + } >> + } else if (!on && qcadev->bt_power->vregs_on) { >> + /* turn off regulator in reverse order */ >> + i = qcadev->bt_power->vreg_data->num_vregs - 1; >> + for ( ; i >= 0; i--) >> + qca_disable_regulator(vregs[i], vreg_bulk[i].consumer); >> + qcadev->bt_power->vregs_on = false; >> + } >> + >> + return ret; >> +} >> + >> +static int qca_init_regulators(struct qca_power *qca, >> + const struct qca_vreg *vregs, size_t num_vregs) >> +{ >> + int i; >> + >> + qca->vreg_bulk = devm_kzalloc(qca->dev, num_vregs * >> + sizeof(struct regulator_bulk_data), >> + GFP_KERNEL); >> + if (!qca->vreg_bulk) >> + return -ENOMEM; >> + >> + for (i = 0; i < num_vregs; i++) >> + qca->vreg_bulk[i].supply = vregs[i].name; >> + >> + return devm_regulator_bulk_get(qca->dev, num_vregs, qca->vreg_bulk); >> +} >> + >> static int qca_serdev_probe(struct serdev_device *serdev) >> { >> struct qca_serdev *qcadev; >> + const struct qca_vreg_data *data; >> int err; >> >> qcadev = devm_kzalloc(&serdev->dev, sizeof(*qcadev), GFP_KERNEL); >> @@ -1014,34 +1301,72 @@ static int qca_serdev_probe(struct >> serdev_device *serdev) >> return -ENOMEM; >> >> qcadev->serdev_hu.serdev = serdev; >> + data = of_device_get_match_data(&serdev->dev); >> + if (data && data->soc_type == BTQCA_CHEROKEE) >> + qcadev->btsoc_type = BTQCA_CHEROKEE; >> + else >> + qcadev->btsoc_type = BTQCA_ROME; >> + >> serdev_device_set_drvdata(serdev, qcadev); >> + if (qcadev->btsoc_type == BTQCA_CHEROKEE) { >> + qcadev->bt_power = devm_kzalloc(&serdev->dev, >> + sizeof(struct qca_power), >> + GFP_KERNEL); >> + if (!qcadev->bt_power) >> + return -ENOMEM; >> + >> + qcadev->bt_power->dev = &serdev->dev; >> + qcadev->bt_power->vreg_data = data; >> + err = qca_init_regulators(qcadev->bt_power, data->vregs, >> + data->num_vregs); >> + if (err) { >> + BT_ERR("Failed to init regulators:%d", err); >> + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); >> + devm_kfree(&serdev->dev, qcadev->bt_power); > > Not necessary, the memory is allocated with devm_kzalloc(&serdev->dev, > ...), therefore it is freed if probe() fails. [Bala]: will update. > >> + goto out; >> + } >> >> - qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable", >> - GPIOD_OUT_LOW); >> - if (IS_ERR(qcadev->bt_en)) { >> - dev_err(&serdev->dev, "failed to acquire enable gpio\n"); >> - return PTR_ERR(qcadev->bt_en); >> - } >> + qcadev->bt_power->vregs_on = false; >> + device_property_read_u32(&serdev->dev, "max-speed", >> + &qcadev->oper_speed); >> + if (!qcadev->oper_speed) >> + BT_INFO("UART will pick default operating speed"); >> + err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); >> + if (err) { >> + BT_ERR("wcn3990 serdev registration failed"); >> + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); >> + devm_kfree(&serdev->dev, qcadev->bt_power); > > no need to free memory. [Bala]: will update. > >> + goto out; >> + } >> + } else { >> + qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable", >> + GPIOD_OUT_LOW); >> + if (IS_ERR(qcadev->bt_en)) { >> + dev_err(&serdev->dev, "failed to acquire enable gpio\n"); >> + return PTR_ERR(qcadev->bt_en); >> + } >> >> - qcadev->susclk = devm_clk_get(&serdev->dev, NULL); >> - if (IS_ERR(qcadev->susclk)) { >> - dev_err(&serdev->dev, "failed to acquire clk\n"); >> - return PTR_ERR(qcadev->susclk); >> - } >> + qcadev->susclk = devm_clk_get(&serdev->dev, NULL); >> + if (IS_ERR(qcadev->susclk)) { >> + dev_err(&serdev->dev, "failed to acquire clk\n"); >> + return PTR_ERR(qcadev->susclk); >> + } >> >> - err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ); >> - if (err) >> - return err; >> + err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ); >> + if (err) >> + return err; >> >> - err = clk_prepare_enable(qcadev->susclk); >> - if (err) >> - return err; >> + err = clk_prepare_enable(qcadev->susclk); >> + if (err) >> + return err; >> >> - err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); >> - if (err) >> - clk_disable_unprepare(qcadev->susclk); >> + err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); >> + if (err) >> + clk_disable_unprepare(qcadev->susclk); >> + } >> + >> +out: return err; >> >> - return err; >> } >> >> static void qca_serdev_remove(struct serdev_device *serdev) >> @@ -1050,11 +1375,17 @@ static void qca_serdev_remove(struct >> serdev_device *serdev) >> >> hci_uart_unregister_device(&qcadev->serdev_hu); >> >> - clk_disable_unprepare(qcadev->susclk); >> + if (qcadev->btsoc_type == BTQCA_CHEROKEE) { >> + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); >> + devm_kfree(&serdev->dev, qcadev->bt_power); > > no need to free memory [Bala]: will update. Thanks for reviewing will update the about comments in next patch set.
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h index e93e0660cf6c..2e551b029970 100644 --- a/drivers/bluetooth/btqca.h +++ b/drivers/bluetooth/btqca.h @@ -37,6 +37,9 @@ #define EDL_TAG_ID_HCI (17) #define EDL_TAG_ID_DEEP_SLEEP (27) +#define CHEROKEE_POWERON_PULSE 0xFC +#define CHEROKEE_POWEROFF_PULSE 0xC0 + enum qca_bardrate { QCA_BAUDRATE_115200 = 0, QCA_BAUDRATE_57600, @@ -124,6 +127,9 @@ struct tlv_type_hdr { __u8 data[0]; } __packed; +int qca_btsoc_power_setup(struct hci_uart *hu, bool on); +int qca_btsoc_shutdown(struct hci_dev *hdev); + #if IS_ENABLED(CONFIG_BT_QCA) int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr); diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c index cb1034998040..e235be0e5202 100644 --- a/drivers/bluetooth/hci_qca.c +++ b/drivers/bluetooth/hci_qca.c @@ -5,7 +5,7 @@ * protocol extension to H4. * * Copyright (C) 2007 Texas Instruments, Inc. - * Copyright (c) 2010, 2012 The Linux Foundation. All rights reserved. + * Copyright (c) 2010, 2012, 2018 The Linux Foundation. All rights reserved. * * Acknowledgements: * This file is based on hci_ll.c, which was... @@ -31,9 +31,14 @@ #include <linux/kernel.h> #include <linux/clk.h> #include <linux/debugfs.h> +#include <linux/delay.h> +#include <linux/device.h> #include <linux/gpio/consumer.h> #include <linux/mod_devicetable.h> #include <linux/module.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/regulator/consumer.h> #include <linux/serdev.h> #include <net/bluetooth/bluetooth.h> @@ -119,10 +124,48 @@ struct qca_data { u64 votes_off; }; +enum qca_btsoc_type { + BTQCA_INVALID = -1, + BTQCA_AR3002, + BTQCA_ROME, + BTQCA_CHEROKEE +}; + +/* + * Voltage regulator information required for configuring the + * QCA Bluetooth chipset + */ +struct qca_vreg { + const char *name; + unsigned int min_uV; + unsigned int max_uV; + unsigned int load_uA; +}; + +struct qca_vreg_data { + enum qca_btsoc_type soc_type; + struct qca_vreg *vregs; + size_t num_vregs; +}; + +/* + * Platform data for the QCA Bluetooth power driver. + */ +struct qca_power { + struct device *dev; + const struct qca_vreg_data *vreg_data; + struct regulator_bulk_data *vreg_bulk; + bool vregs_on; +}; + struct qca_serdev { struct hci_uart serdev_hu; struct gpio_desc *bt_en; struct clk *susclk; + enum qca_btsoc_type btsoc_type; + struct qca_power *bt_power; + u32 init_speed; + u32 oper_speed; }; static void __serial_clock_on(struct tty_struct *tty) @@ -402,6 +445,7 @@ static int qca_open(struct hci_uart *hu) { struct qca_serdev *qcadev; struct qca_data *qca; + int ret = 0; BT_DBG("hu %p qca_open", hu); @@ -463,13 +507,19 @@ static int qca_open(struct hci_uart *hu) serdev_device_open(hu->serdev); qcadev = serdev_device_get_drvdata(hu->serdev); - gpiod_set_value_cansleep(qcadev->bt_en, 1); + if (qcadev->btsoc_type == BTQCA_CHEROKEE) { + hu->init_speed = qcadev->init_speed; + hu->oper_speed = qcadev->oper_speed; + ret = qca_btsoc_power_setup(hu, true); + } else { + gpiod_set_value_cansleep(qcadev->bt_en, 1); + } } BT_DBG("HCI_UART_QCA open, tx_idle_delay=%u, wake_retrans=%u", qca->tx_idle_delay, qca->wake_retrans); - return 0; + return ret; } static void qca_debugfs_init(struct hci_dev *hdev) @@ -552,7 +602,10 @@ static int qca_close(struct hci_uart *hu) serdev_device_close(hu->serdev); qcadev = serdev_device_get_drvdata(hu->serdev); - gpiod_set_value_cansleep(qcadev->bt_en, 0); + if (qcadev->btsoc_type == BTQCA_CHEROKEE) + qca_btsoc_shutdown(hu->hdev); + else + gpiod_set_value_cansleep(qcadev->bt_en, 0); } kfree_skb(qca->rx_skb); @@ -925,20 +978,36 @@ static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed) hci_uart_set_baudrate(hu, speed); } -static int qca_setup(struct hci_uart *hu) +static int qca_send_vendor_cmd(struct hci_dev *hdev, u8 cmd) { - struct hci_dev *hdev = hu->hdev; + struct hci_uart *hu = hci_get_drvdata(hdev); struct qca_data *qca = hu->priv; - unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200; - int ret; + struct sk_buff *skb; - bt_dev_info(hdev, "ROME setup"); + bt_dev_dbg(hdev, "sending command %02x to SoC", cmd); - /* Patch downloading has to be done without IBS mode */ - clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); + skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL); + if (!skb) { + bt_dev_err(hdev, "Failed to allocate memory for skb packet"); + return -ENOMEM; + } + + skb_put_data(skb, &cmd, sizeof(cmd)); + hci_skb_pkt_type(skb) = HCI_COMMAND_PKT; + + skb_queue_tail(&qca->txq, skb); + hci_uart_tx_wakeup(hu); + + /* Wait for 100 uS for SoC to settle down */ + usleep_range(100, 200); + + return 0; +} + +static void qca_set_init_speed(struct hci_uart *hu) +{ + unsigned int speed = 0; - /* Setup initial baudrate */ - speed = 0; if (hu->init_speed) speed = hu->init_speed; else if (hu->proto->init_speed) @@ -946,29 +1015,136 @@ static int qca_setup(struct hci_uart *hu) if (speed) host_set_baudrate(hu, speed); +} + +static int qca_set_operating_speed(struct hci_uart *hu, u32 *qca_baudrate) +{ + unsigned int speed = 0; + int ret; - /* Setup user speed if needed */ - speed = 0; if (hu->oper_speed) speed = hu->oper_speed; else if (hu->proto->oper_speed) speed = hu->proto->oper_speed; if (speed) { - qca_baudrate = qca_get_baudrate_value(speed); - - bt_dev_info(hdev, "Set UART speed to %d", speed); - ret = qca_set_baudrate(hdev, qca_baudrate); + *qca_baudrate = qca_get_baudrate_value(speed); + bt_dev_info(hu->hdev, "Set UART speed to %d", speed); + ret = qca_set_baudrate(hu->hdev, *qca_baudrate); if (ret) { - bt_dev_err(hdev, "Failed to change the baud rate (%d)", + bt_dev_err(hu->hdev, "Failed to change the baud rate (%d)", ret); return ret; } host_set_baudrate(hu, speed); } - /* Setup patch / NVM configurations */ - ret = qca_uart_setup_rome(hdev, qca_baudrate); + return ret; +} + +int qca_btsoc_shutdown(struct hci_dev *hdev) +{ + struct hci_uart *hu = hci_get_drvdata(hdev); + + /* change host baud rate before sending power off command */ + host_set_baudrate(hu, 2400); + qca_send_vendor_cmd(hdev, CHEROKEE_POWEROFF_PULSE); + /* turn off btsoc */ + return qca_btsoc_power_setup(hu, false); +} + +static int qca_setup(struct hci_uart *hu) +{ + struct hci_dev *hdev = hu->hdev; + struct qca_data *qca = hu->priv; + struct qca_serdev *qcadev; + unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200; + int ret; + int soc_ver; + + qcadev = serdev_device_get_drvdata(hu->serdev); + + switch (qcadev->btsoc_type) { + case BTQCA_CHEROKEE: + bt_dev_dbg(hdev, "setting up wcn3990"); + /* Patch downloading has to be done without IBS mode */ + clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); + qca_set_init_speed(hu); + hci_uart_set_flow_control(hu, true); + ret = qca_send_vendor_cmd(hdev, CHEROKEE_POWERON_PULSE); + if (ret) { + bt_dev_err(hdev, "failed to send power on command"); + return ret; + } + + /* Close and re-open the port */ + serdev_device_close(hu->serdev); + ret = serdev_device_open(hu->serdev); + if (ret) { + bt_dev_err(hdev, "failed to open port"); + return ret; + } + + qca_set_init_speed(hu); + hci_uart_set_flow_control(hu, false); + msleep(100); + ret = qca_patch_ver_req(hdev, &soc_ver); + if (ret < 0 || soc_ver == 0) { + bt_dev_err(hdev, "Failed to get version 0x%x", ret); + return ret; + } + + bt_dev_info(hdev, "wcn3990 controller version 0x%08x", soc_ver); + hci_uart_set_flow_control(hu, true); + ret = qca_set_operating_speed(hu, &qca_baudrate); + if (ret) + return ret; + hci_uart_set_flow_control(hu, false); + /* Setup patch and NVM configurations */ + ret = qca_uart_setup_cherokee(hdev, qca_baudrate, &soc_ver); + + break; + + default: + bt_dev_info(hdev, "ROME setup"); + + /* Patch downloading has to be done without IBS mode */ + clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); + + /* Setup initial baudrate */ + speed = 0; + if (hu->init_speed) + speed = hu->init_speed; + else if (hu->proto->init_speed) + speed = hu->proto->init_speed; + + if (speed) + host_set_baudrate(hu, speed); + + /* Setup user speed if needed */ + speed = 0; + if (hu->oper_speed) + speed = hu->oper_speed; + else if (hu->proto->oper_speed) + speed = hu->proto->oper_speed; + + if (speed) { + qca_baudrate = qca_get_baudrate_value(speed); + + bt_dev_info(hdev, "Set UART speed to %d", speed); + ret = qca_set_baudrate(hdev, qca_baudrate); + if (ret) { + bt_dev_err(hdev, "Failed to change the baud rate (%d)", + ret); + return ret; + } + host_set_baudrate(hu, speed); + } + + /* Setup patch / NVM configurations */ + ret = qca_uart_setup_rome(hdev, qca_baudrate); + } + if (!ret) { set_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags); qca_debugfs_init(hdev); @@ -1004,9 +1180,120 @@ static struct hci_uart_proto qca_proto = { .dequeue = qca_dequeue, }; +static const struct qca_vreg_data qca_cherokee_data = { + .soc_type = BTQCA_CHEROKEE, + .vregs = (struct qca_vreg []) { + { "vddio", 1352000, 1352000, 0 }, + { "vddxtal", 1904000, 2040000, 0 }, + { "vddcore", 1800000, 1800000, 1 }, + { "vddpa", 1304000, 1304000, 1 }, + { "vddldo", 3000000, 3312000, 1 }, + }, + .num_vregs = 5, +}; + +static int qca_enable_regulator(struct qca_vreg vregs, + struct regulator *regulator) +{ + int ret; + + ret = regulator_set_voltage(regulator, vregs.min_uV, + vregs.max_uV); + if (ret) + goto out; + + if (vregs.load_uA) + ret = regulator_set_load(regulator, + vregs.load_uA); + + if (ret) + goto out; + + ret = regulator_enable(regulator); + +out: + return ret; + +} + +static void qca_disable_regulator(struct qca_vreg vregs, + struct regulator *regulator) +{ + /* Disable the regulator if requested by user + * or when fault to enable any regulator. + */ + regulator_disable(regulator); + regulator_set_voltage(regulator, 0, vregs.max_uV); + if (vregs.load_uA) + regulator_set_load(regulator, 0); + +} + +int qca_btsoc_power_setup(struct hci_uart *hu, bool on) +{ + struct qca_vreg *vregs; + struct regulator_bulk_data *vreg_bulk; + struct qca_serdev *qcadev; + int i, num_vregs, ret = 0; + + qcadev = serdev_device_get_drvdata(hu->serdev); + if (!qcadev || !qcadev->bt_power || !qcadev->bt_power->vreg_data || + !qcadev->bt_power->vreg_bulk) + return -EINVAL; + + vregs = qcadev->bt_power->vreg_data->vregs; + vreg_bulk = qcadev->bt_power->vreg_bulk; + num_vregs = qcadev->bt_power->vreg_data->num_vregs; + BT_DBG("on: %d", on); + if (on && !qcadev->bt_power->vregs_on) { + for (i = 0; i < num_vregs; i++) { + ret = qca_enable_regulator(vregs[i], + vreg_bulk[i].consumer); + if (ret) + break; + } + /* regulators failed */ + if (ret) { + BT_ERR("failed to enable regulator:%s", vregs[i].name); + /* turn off regulators which are enabled */ + for (i = i - 1; i >= 0; i--) + qca_disable_regulator(vregs[i], + vreg_bulk[i].consumer); + } else { + qcadev->bt_power->vregs_on = true; + } + } else if (!on && qcadev->bt_power->vregs_on) { + /* turn off regulator in reverse order */ + i = qcadev->bt_power->vreg_data->num_vregs - 1; + for ( ; i >= 0; i--) + qca_disable_regulator(vregs[i], vreg_bulk[i].consumer); + qcadev->bt_power->vregs_on = false; + } + + return ret; +} + +static int qca_init_regulators(struct qca_power *qca, + const struct qca_vreg *vregs, size_t num_vregs) +{ + int i; + + qca->vreg_bulk = devm_kzalloc(qca->dev, num_vregs * + sizeof(struct regulator_bulk_data), + GFP_KERNEL); + if (!qca->vreg_bulk) + return -ENOMEM; + + for (i = 0; i < num_vregs; i++) + qca->vreg_bulk[i].supply = vregs[i].name; + + return devm_regulator_bulk_get(qca->dev, num_vregs, qca->vreg_bulk); +} + static int qca_serdev_probe(struct serdev_device *serdev) { struct qca_serdev *qcadev; + const struct qca_vreg_data *data; int err; qcadev = devm_kzalloc(&serdev->dev, sizeof(*qcadev), GFP_KERNEL); @@ -1014,34 +1301,72 @@ static int qca_serdev_probe(struct serdev_device *serdev) return -ENOMEM; qcadev->serdev_hu.serdev = serdev; + data = of_device_get_match_data(&serdev->dev); + if (data && data->soc_type == BTQCA_CHEROKEE) + qcadev->btsoc_type = BTQCA_CHEROKEE; + else + qcadev->btsoc_type = BTQCA_ROME; + serdev_device_set_drvdata(serdev, qcadev); + if (qcadev->btsoc_type == BTQCA_CHEROKEE) { + qcadev->bt_power = devm_kzalloc(&serdev->dev, + sizeof(struct qca_power), + GFP_KERNEL); + if (!qcadev->bt_power) + return -ENOMEM; + + qcadev->bt_power->dev = &serdev->dev; + qcadev->bt_power->vreg_data = data; + err = qca_init_regulators(qcadev->bt_power, data->vregs, + data->num_vregs); + if (err) { + BT_ERR("Failed to init regulators:%d", err); + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); + devm_kfree(&serdev->dev, qcadev->bt_power); + goto out; + } - qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable", - GPIOD_OUT_LOW); - if (IS_ERR(qcadev->bt_en)) { - dev_err(&serdev->dev, "failed to acquire enable gpio\n"); - return PTR_ERR(qcadev->bt_en); - } + qcadev->bt_power->vregs_on = false; + device_property_read_u32(&serdev->dev, "max-speed", + &qcadev->oper_speed); + if (!qcadev->oper_speed) + BT_INFO("UART will pick default operating speed"); + err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); + if (err) { + BT_ERR("wcn3990 serdev registration failed"); + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); + devm_kfree(&serdev->dev, qcadev->bt_power); + goto out; + } + } else { + qcadev->bt_en = devm_gpiod_get(&serdev->dev, "enable", + GPIOD_OUT_LOW); + if (IS_ERR(qcadev->bt_en)) { + dev_err(&serdev->dev, "failed to acquire enable gpio\n"); + return PTR_ERR(qcadev->bt_en); + } - qcadev->susclk = devm_clk_get(&serdev->dev, NULL); - if (IS_ERR(qcadev->susclk)) { - dev_err(&serdev->dev, "failed to acquire clk\n"); - return PTR_ERR(qcadev->susclk); - } + qcadev->susclk = devm_clk_get(&serdev->dev, NULL); + if (IS_ERR(qcadev->susclk)) { + dev_err(&serdev->dev, "failed to acquire clk\n"); + return PTR_ERR(qcadev->susclk); + } - err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ); - if (err) - return err; + err = clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ); + if (err) + return err; - err = clk_prepare_enable(qcadev->susclk); - if (err) - return err; + err = clk_prepare_enable(qcadev->susclk); + if (err) + return err; - err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); - if (err) - clk_disable_unprepare(qcadev->susclk); + err = hci_uart_register_device(&qcadev->serdev_hu, &qca_proto); + if (err) + clk_disable_unprepare(qcadev->susclk); + } + +out: return err; - return err; } static void qca_serdev_remove(struct serdev_device *serdev) @@ -1050,11 +1375,17 @@ static void qca_serdev_remove(struct serdev_device *serdev) hci_uart_unregister_device(&qcadev->serdev_hu); - clk_disable_unprepare(qcadev->susclk); + if (qcadev->btsoc_type == BTQCA_CHEROKEE) { + devm_kfree(&serdev->dev, qcadev->bt_power->vreg_bulk); + devm_kfree(&serdev->dev, qcadev->bt_power); + } else { + clk_disable_unprepare(qcadev->susclk); + } } static const struct of_device_id qca_bluetooth_of_match[] = { { .compatible = "qcom,qca6174-bt" }, + { .compatible = "qcom,wcn3990-bt", .data = &qca_cherokee_data}, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
Add support to set voltage/current of various regulators to power up/down Bluetooth chip wcn3990. Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> --- Changes in v6: * Hooked up qca_power to qca_serdev. * renamed all the naming inconsistency functions with qca_* * leveraged common code of ROME for wcn3990. * created wrapper functions for re-usable blocks. * updated function of _*regulator_enable and _*regualtor_disable. * removed redundant comments and functions. * addressed review comments. Changes in v5: * updated regulator vddpa min_uV to 1304000. * addressed review comments. Changes in v4: * Segregated the changes of btqca from hci_qca * rebased all changes on top of bluetooth-next. * addressed review comments. --- drivers/bluetooth/btqca.h | 6 + drivers/bluetooth/hci_qca.c | 419 ++++++++++++++++++++++++++++++++---- 2 files changed, 381 insertions(+), 44 deletions(-)