| Message ID | 1529035270-32513-1-git-send-email-abhinavk@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thu, Jun 14, 2018 at 09:01:10PM -0700, Abhinav Kumar wrote: > Currenty the VCO rate in the 10nm PLL driver relies > on the parent rate which is not configured. > > Configure the VCO rate to 19.2 Mhz as required by > the 10nm PLL driver. > > Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org> Sorry for missing this when it was posted. This is consistent with the other files in pll/, so Reviewed-by: Sean Paul <seanpaul@chromium.org> I'll stuff this in dpu-staging/for-next. Sean > --- > drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c | 4 +++- > 1 file changed, 3 insertions(+), 1 deletion(-) > > diff --git a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c > index c4c37a7..fb485cb 100644 > --- a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c > +++ b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c > @@ -39,6 +39,8 @@ > #define DSI_PIXEL_PLL_CLK 1 > #define NUM_PROVIDED_CLKS 2 > > +#define VCO_REF_CLK_RATE 19200000 > + > struct dsi_pll_regs { > u32 pll_prop_gain_rate; > u32 pll_lockdet_rate; > @@ -316,7 +318,7 @@ static int dsi_pll_10nm_vco_set_rate(struct clk_hw *hw, unsigned long rate, > parent_rate); > > pll_10nm->vco_current_rate = rate; > - pll_10nm->vco_ref_clk_rate = parent_rate; > + pll_10nm->vco_ref_clk_rate = VCO_REF_CLK_RATE; > > dsi_pll_setup_config(pll_10nm); > > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project >
diff --git a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c index c4c37a7..fb485cb 100644 --- a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c +++ b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c @@ -39,6 +39,8 @@ #define DSI_PIXEL_PLL_CLK 1 #define NUM_PROVIDED_CLKS 2 +#define VCO_REF_CLK_RATE 19200000 + struct dsi_pll_regs { u32 pll_prop_gain_rate; u32 pll_lockdet_rate; @@ -316,7 +318,7 @@ static int dsi_pll_10nm_vco_set_rate(struct clk_hw *hw, unsigned long rate, parent_rate); pll_10nm->vco_current_rate = rate; - pll_10nm->vco_ref_clk_rate = parent_rate; + pll_10nm->vco_ref_clk_rate = VCO_REF_CLK_RATE; dsi_pll_setup_config(pll_10nm);
Currenty the VCO rate in the 10nm PLL driver relies on the parent rate which is not configured. Configure the VCO rate to 19.2 Mhz as required by the 10nm PLL driver. Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org> --- drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)