diff mbox series

[v4,1/3] Input: edt-ft5x06 - Add support for regulator

Message ID 20180725073410.730-2-mylene.josserand@bootlin.com (mailing list archive)
State Changes Requested
Headers show
Series sun8i-a83t: Add touchscreen support on TBS A711 | expand

Commit Message

Mylène Josserand July 25, 2018, 7:34 a.m. UTC
Add the support of regulator to use it as VCC source.

Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/input/touchscreen/edt-ft5x06.txt      |  1 +
 drivers/input/touchscreen/edt-ft5x06.c             | 43 ++++++++++++++++++++++
 2 files changed, 44 insertions(+)

Comments

Dmitry Torokhov July 26, 2018, 12:47 a.m. UTC | #1
Hi Mylène,

On Wed, Jul 25, 2018 at 09:34:08AM +0200, Mylène Josserand wrote:
> Add the support of regulator to use it as VCC source.
> 
> Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
>  .../bindings/input/touchscreen/edt-ft5x06.txt      |  1 +
>  drivers/input/touchscreen/edt-ft5x06.c             | 43 ++++++++++++++++++++++
>  2 files changed, 44 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> index 025cf8c9324a..48e975b9c1aa 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> @@ -30,6 +30,7 @@ Required properties:
>  Optional properties:
>   - reset-gpios: GPIO specification for the RESET input
>   - wake-gpios:  GPIO specification for the WAKE input
> + - vcc-supply:  Regulator that supplies the touchscreen
>  
>   - pinctrl-names: should be "default"
>   - pinctrl-0:   a phandle pointing to the pin settings for the
> diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> index 1e18ca0d1b4e..dcde719094f7 100644
> --- a/drivers/input/touchscreen/edt-ft5x06.c
> +++ b/drivers/input/touchscreen/edt-ft5x06.c
> @@ -39,6 +39,7 @@
>  #include <linux/input/mt.h>
>  #include <linux/input/touchscreen.h>
>  #include <linux/of_device.h>
> +#include <linux/regulator/consumer.h>
>  
>  #define WORK_REGISTER_THRESHOLD		0x00
>  #define WORK_REGISTER_REPORT_RATE	0x08
> @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
>  	struct touchscreen_properties prop;
>  	u16 num_x;
>  	u16 num_y;
> +	struct regulator *vcc;
>  
>  	struct gpio_desc *reset_gpio;
>  	struct gpio_desc *wake_gpio;
> @@ -963,6 +965,13 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
>  	}
>  }
>  
> +static void edt_ft5x06_disable_regulator(void *arg)
> +{
> +	struct edt_ft5x06_ts_data *data = arg;
> +
> +	regulator_disable(data->vcc);
> +}
> +
>  static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  					 const struct i2c_device_id *id)
>  {
> @@ -991,6 +1000,28 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
>  
>  	tsdata->max_support_points = chip_data->max_support_points;
>  
> +	tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> +	if (IS_ERR(tsdata->vcc)) {
> +		error = PTR_ERR(tsdata->vcc);
> +		if (error != -EPROBE_DEFER)
> +			dev_err(&client->dev, "failed to request regulator: %d\n",
> +				error);
> +		return error;
> +	}
> +
> +	error = regulator_enable(tsdata->vcc);
> +	if (error < 0) {
> +		dev_err(&client->dev, "failed to enable vcc: %d\n",
> +			error);
> +		return error;
> +	}

It is better to put the chip into reset and then power up the regulatori
and take it out of the reset, rather than power up and then toggle reset
on and off.

> +
> +	error = devm_add_action_or_reset(&client->dev,
> +					 edt_ft5x06_disable_regulator,
> +					 tsdata);
> +	if (error)
> +		return error;
> +
>  	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
>  						     "reset", GPIOD_OUT_HIGH);
>  	if (IS_ERR(tsdata->reset_gpio)) {
> @@ -1120,9 +1151,12 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
>  static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
>  {
>  	struct i2c_client *client = to_i2c_client(dev);
> +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
>  
>  	if (device_may_wakeup(dev))
>  		enable_irq_wake(client->irq);
> +	else
> +		regulator_disable(tsdata->vcc);
>  
>  	return 0;
>  }
> @@ -1130,9 +1164,18 @@ static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
>  static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
>  {
>  	struct i2c_client *client = to_i2c_client(dev);
> +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> +	int ret;
>  
>  	if (device_may_wakeup(dev))
>  		disable_irq_wake(client->irq);
> +	else {
> +		ret = regulator_enable(tsdata->vcc);
> +		if (ret < 0) {
> +			dev_err(dev, "failed to enable vcc: %d\n", ret);
> +			return ret;
> +		}
> +	}

I believe I mentioned in other review that once you powered up the
device, you need to restore its settings, include switching to factory
mode, if it was in factory mode, and restoring threshold/gain/offset
settings.

Thanks.
Mylène Josserand Aug. 7, 2018, 6:59 a.m. UTC | #2
Hello Dmitry,

Thank you again for the review.

On Wed, 25 Jul 2018 17:47:32 -0700
Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:

> Hi Mylène,
> 
> On Wed, Jul 25, 2018 at 09:34:08AM +0200, Mylène Josserand wrote:
> > Add the support of regulator to use it as VCC source.
> > 
> > Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
> > Reviewed-by: Rob Herring <robh@kernel.org>
> > ---
> >  .../bindings/input/touchscreen/edt-ft5x06.txt      |  1 +
> >  drivers/input/touchscreen/edt-ft5x06.c             | 43 ++++++++++++++++++++++
> >  2 files changed, 44 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > index 025cf8c9324a..48e975b9c1aa 100644
> > --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > @@ -30,6 +30,7 @@ Required properties:
> >  Optional properties:
> >   - reset-gpios: GPIO specification for the RESET input
> >   - wake-gpios:  GPIO specification for the WAKE input
> > + - vcc-supply:  Regulator that supplies the touchscreen
> >  
> >   - pinctrl-names: should be "default"
> >   - pinctrl-0:   a phandle pointing to the pin settings for the
> > diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> > index 1e18ca0d1b4e..dcde719094f7 100644
> > --- a/drivers/input/touchscreen/edt-ft5x06.c
> > +++ b/drivers/input/touchscreen/edt-ft5x06.c
> > @@ -39,6 +39,7 @@
> >  #include <linux/input/mt.h>
> >  #include <linux/input/touchscreen.h>
> >  #include <linux/of_device.h>
> > +#include <linux/regulator/consumer.h>
> >  
> >  #define WORK_REGISTER_THRESHOLD		0x00
> >  #define WORK_REGISTER_REPORT_RATE	0x08
> > @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
> >  	struct touchscreen_properties prop;
> >  	u16 num_x;
> >  	u16 num_y;
> > +	struct regulator *vcc;
> >  
> >  	struct gpio_desc *reset_gpio;
> >  	struct gpio_desc *wake_gpio;
> > @@ -963,6 +965,13 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
> >  	}
> >  }
> >  
> > +static void edt_ft5x06_disable_regulator(void *arg)
> > +{
> > +	struct edt_ft5x06_ts_data *data = arg;
> > +
> > +	regulator_disable(data->vcc);
> > +}
> > +
> >  static int edt_ft5x06_ts_probe(struct i2c_client *client,
> >  					 const struct i2c_device_id *id)
> >  {
> > @@ -991,6 +1000,28 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> >  
> >  	tsdata->max_support_points = chip_data->max_support_points;
> >  
> > +	tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> > +	if (IS_ERR(tsdata->vcc)) {
> > +		error = PTR_ERR(tsdata->vcc);
> > +		if (error != -EPROBE_DEFER)
> > +			dev_err(&client->dev, "failed to request regulator: %d\n",
> > +				error);
> > +		return error;
> > +	}
> > +
> > +	error = regulator_enable(tsdata->vcc);
> > +	if (error < 0) {
> > +		dev_err(&client->dev, "failed to enable vcc: %d\n",
> > +			error);
> > +		return error;
> > +	}  
> 
> It is better to put the chip into reset and then power up the regulatori
> and take it out of the reset, rather than power up and then toggle reset
> on and off.

okay, thanks, I will update it.

> 
> > +
> > +	error = devm_add_action_or_reset(&client->dev,
> > +					 edt_ft5x06_disable_regulator,
> > +					 tsdata);
> > +	if (error)
> > +		return error;
> > +
> >  	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
> >  						     "reset", GPIOD_OUT_HIGH);
> >  	if (IS_ERR(tsdata->reset_gpio)) {
> > @@ -1120,9 +1151,12 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
> >  static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> >  {
> >  	struct i2c_client *client = to_i2c_client(dev);
> > +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> >  
> >  	if (device_may_wakeup(dev))
> >  		enable_irq_wake(client->irq);
> > +	else
> > +		regulator_disable(tsdata->vcc);
> >  
> >  	return 0;
> >  }
> > @@ -1130,9 +1164,18 @@ static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> >  static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
> >  {
> >  	struct i2c_client *client = to_i2c_client(dev);
> > +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > +	int ret;
> >  
> >  	if (device_may_wakeup(dev))
> >  		disable_irq_wake(client->irq);
> > +	else {
> > +		ret = regulator_enable(tsdata->vcc);
> > +		if (ret < 0) {
> > +			dev_err(dev, "failed to enable vcc: %d\n", ret);
> > +			return ret;
> > +		}
> > +	}  
> 
> I believe I mentioned in other review that once you powered up the
> device, you need to restore its settings, include switching to factory
> mode, if it was in factory mode, and restoring threshold/gain/offset
> settings.

Yes, I will update the driver with that but as I told you in a previous
mail, I can't test the suspend/resume :(

Best regards,
Dmitry Torokhov Aug. 23, 2018, 12:48 a.m. UTC | #3
On Tue, Aug 07, 2018 at 08:59:44AM +0200, Mylène Josserand wrote:
> Hello Dmitry,
> 
> Thank you again for the review.
> 
> On Wed, 25 Jul 2018 17:47:32 -0700
> Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:
> 
> > Hi Mylène,
> > 
> > On Wed, Jul 25, 2018 at 09:34:08AM +0200, Mylène Josserand wrote:
> > > Add the support of regulator to use it as VCC source.
> > > 
> > > Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
> > > Reviewed-by: Rob Herring <robh@kernel.org>
> > > ---
> > >  .../bindings/input/touchscreen/edt-ft5x06.txt      |  1 +
> > >  drivers/input/touchscreen/edt-ft5x06.c             | 43 ++++++++++++++++++++++
> > >  2 files changed, 44 insertions(+)
> > > 
> > > diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > index 025cf8c9324a..48e975b9c1aa 100644
> > > --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> > > @@ -30,6 +30,7 @@ Required properties:
> > >  Optional properties:
> > >   - reset-gpios: GPIO specification for the RESET input
> > >   - wake-gpios:  GPIO specification for the WAKE input
> > > + - vcc-supply:  Regulator that supplies the touchscreen
> > >  
> > >   - pinctrl-names: should be "default"
> > >   - pinctrl-0:   a phandle pointing to the pin settings for the
> > > diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
> > > index 1e18ca0d1b4e..dcde719094f7 100644
> > > --- a/drivers/input/touchscreen/edt-ft5x06.c
> > > +++ b/drivers/input/touchscreen/edt-ft5x06.c
> > > @@ -39,6 +39,7 @@
> > >  #include <linux/input/mt.h>
> > >  #include <linux/input/touchscreen.h>
> > >  #include <linux/of_device.h>
> > > +#include <linux/regulator/consumer.h>
> > >  
> > >  #define WORK_REGISTER_THRESHOLD		0x00
> > >  #define WORK_REGISTER_REPORT_RATE	0x08
> > > @@ -91,6 +92,7 @@ struct edt_ft5x06_ts_data {
> > >  	struct touchscreen_properties prop;
> > >  	u16 num_x;
> > >  	u16 num_y;
> > > +	struct regulator *vcc;
> > >  
> > >  	struct gpio_desc *reset_gpio;
> > >  	struct gpio_desc *wake_gpio;
> > > @@ -963,6 +965,13 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
> > >  	}
> > >  }
> > >  
> > > +static void edt_ft5x06_disable_regulator(void *arg)
> > > +{
> > > +	struct edt_ft5x06_ts_data *data = arg;
> > > +
> > > +	regulator_disable(data->vcc);
> > > +}
> > > +
> > >  static int edt_ft5x06_ts_probe(struct i2c_client *client,
> > >  					 const struct i2c_device_id *id)
> > >  {
> > > @@ -991,6 +1000,28 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
> > >  
> > >  	tsdata->max_support_points = chip_data->max_support_points;
> > >  
> > > +	tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
> > > +	if (IS_ERR(tsdata->vcc)) {
> > > +		error = PTR_ERR(tsdata->vcc);
> > > +		if (error != -EPROBE_DEFER)
> > > +			dev_err(&client->dev, "failed to request regulator: %d\n",
> > > +				error);
> > > +		return error;
> > > +	}
> > > +
> > > +	error = regulator_enable(tsdata->vcc);
> > > +	if (error < 0) {
> > > +		dev_err(&client->dev, "failed to enable vcc: %d\n",
> > > +			error);
> > > +		return error;
> > > +	}  
> > 
> > It is better to put the chip into reset and then power up the regulatori
> > and take it out of the reset, rather than power up and then toggle reset
> > on and off.
> 
> okay, thanks, I will update it.
> 
> > 
> > > +
> > > +	error = devm_add_action_or_reset(&client->dev,
> > > +					 edt_ft5x06_disable_regulator,
> > > +					 tsdata);
> > > +	if (error)
> > > +		return error;
> > > +
> > >  	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
> > >  						     "reset", GPIOD_OUT_HIGH);
> > >  	if (IS_ERR(tsdata->reset_gpio)) {
> > > @@ -1120,9 +1151,12 @@ static int edt_ft5x06_ts_remove(struct i2c_client *client)
> > >  static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> > >  {
> > >  	struct i2c_client *client = to_i2c_client(dev);
> > > +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > >  
> > >  	if (device_may_wakeup(dev))
> > >  		enable_irq_wake(client->irq);
> > > +	else
> > > +		regulator_disable(tsdata->vcc);
> > >  
> > >  	return 0;
> > >  }
> > > @@ -1130,9 +1164,18 @@ static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
> > >  static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
> > >  {
> > >  	struct i2c_client *client = to_i2c_client(dev);
> > > +	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
> > > +	int ret;
> > >  
> > >  	if (device_may_wakeup(dev))
> > >  		disable_irq_wake(client->irq);
> > > +	else {
> > > +		ret = regulator_enable(tsdata->vcc);
> > > +		if (ret < 0) {
> > > +			dev_err(dev, "failed to enable vcc: %d\n", ret);
> > > +			return ret;
> > > +		}
> > > +	}  
> > 
> > I believe I mentioned in other review that once you powered up the
> > device, you need to restore its settings, include switching to factory
> > mode, if it was in factory mode, and restoring threshold/gain/offset
> > settings.
> 
> Yes, I will update the driver with that but as I told you in a previous
> mail, I can't test the suspend/resume :(

I wonder if Simon or Lothar or Franklin could help us with it (CCed). If
not, then we'll have to go by review only.

Thanks.
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
index 025cf8c9324a..48e975b9c1aa 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
@@ -30,6 +30,7 @@  Required properties:
 Optional properties:
  - reset-gpios: GPIO specification for the RESET input
  - wake-gpios:  GPIO specification for the WAKE input
+ - vcc-supply:  Regulator that supplies the touchscreen
 
  - pinctrl-names: should be "default"
  - pinctrl-0:   a phandle pointing to the pin settings for the
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index 1e18ca0d1b4e..dcde719094f7 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -39,6 +39,7 @@ 
 #include <linux/input/mt.h>
 #include <linux/input/touchscreen.h>
 #include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
 
 #define WORK_REGISTER_THRESHOLD		0x00
 #define WORK_REGISTER_REPORT_RATE	0x08
@@ -91,6 +92,7 @@  struct edt_ft5x06_ts_data {
 	struct touchscreen_properties prop;
 	u16 num_x;
 	u16 num_y;
+	struct regulator *vcc;
 
 	struct gpio_desc *reset_gpio;
 	struct gpio_desc *wake_gpio;
@@ -963,6 +965,13 @@  edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
 	}
 }
 
+static void edt_ft5x06_disable_regulator(void *arg)
+{
+	struct edt_ft5x06_ts_data *data = arg;
+
+	regulator_disable(data->vcc);
+}
+
 static int edt_ft5x06_ts_probe(struct i2c_client *client,
 					 const struct i2c_device_id *id)
 {
@@ -991,6 +1000,28 @@  static int edt_ft5x06_ts_probe(struct i2c_client *client,
 
 	tsdata->max_support_points = chip_data->max_support_points;
 
+	tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
+	if (IS_ERR(tsdata->vcc)) {
+		error = PTR_ERR(tsdata->vcc);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev, "failed to request regulator: %d\n",
+				error);
+		return error;
+	}
+
+	error = regulator_enable(tsdata->vcc);
+	if (error < 0) {
+		dev_err(&client->dev, "failed to enable vcc: %d\n",
+			error);
+		return error;
+	}
+
+	error = devm_add_action_or_reset(&client->dev,
+					 edt_ft5x06_disable_regulator,
+					 tsdata);
+	if (error)
+		return error;
+
 	tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
 						     "reset", GPIOD_OUT_HIGH);
 	if (IS_ERR(tsdata->reset_gpio)) {
@@ -1120,9 +1151,12 @@  static int edt_ft5x06_ts_remove(struct i2c_client *client)
 static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
+	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
 
 	if (device_may_wakeup(dev))
 		enable_irq_wake(client->irq);
+	else
+		regulator_disable(tsdata->vcc);
 
 	return 0;
 }
@@ -1130,9 +1164,18 @@  static int __maybe_unused edt_ft5x06_ts_suspend(struct device *dev)
 static int __maybe_unused edt_ft5x06_ts_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
+	struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
+	int ret;
 
 	if (device_may_wakeup(dev))
 		disable_irq_wake(client->irq);
+	else {
+		ret = regulator_enable(tsdata->vcc);
+		if (ret < 0) {
+			dev_err(dev, "failed to enable vcc: %d\n", ret);
+			return ret;
+		}
+	}
 
 	return 0;
 }