[v2] arm64: dts: rockchip: add support for ROC-RK3399-PC board
diff mbox series

Message ID 1532916721-24117-1-git-send-email-djw@t-chip.com.cn
State New
Headers show
Series
  • [v2] arm64: dts: rockchip: add support for ROC-RK3399-PC board
Related show

Commit Message

Levin Du July 30, 2018, 2:12 a.m. UTC
From: Levin Du <djw@t-chip.com.cn>

ROC-RK3399-PC is a power efficient 4GB LPDDR4 single board
computer with USB 3.0 and Gigabit Ethernet in a form factor
compatible with the Raspberry Pi. It is based on the Rockchip
RK3399 SoC, powered by the Type-C port.

The devicetree currently supports peripherals of:

- Ethernet
- HDMI
- SD Card
- UART2 debug
- Type-C
- eMMC

USB3 in Type-C port currently only works with normal orientation,
not flip one.

Signed-off-by: Levin Du <djw@t-chip.com.cn>

---

Changes in v2:
- remove custom brightness-levels (use calculated one in pwm_bl driver)
- remove redundant 'dr_mode="otg"' in usbdrd_dwc3_0

Changes in v1:
- remove bootargs
- use interpolation for brightness level
- add vcc_vbus_typec1 regulator
- fix phy-supply of u2phy0_otg and u2phy1_otg
- remove vcc_hub_en dummy regualtor
- add hub_rst (changed to output high) to pinctrl status of vcc5v0_host
- remove vsel-gpios props in fan53xx
- remove mp8859 in i2c
- fusb302: fix interrupt setting
- fusb302: add vbus-supply
- remove extcon in tcphy0 and tcphy1
- remove #sound-dai-cells in i2s*
- use RK_PXX style bit number for cd-gpios in SDMMC
- clean commented status lines

 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm64/boot/dts/rockchip/Makefile              |   1 +
 arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts     | 682 +++++++++++++++++++++
 3 files changed, 687 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts

Comments

Rob Herring July 31, 2018, 8:51 p.m. UTC | #1
On Mon, Jul 30, 2018 at 10:12:01AM +0800, djw@t-chip.com.cn wrote:
> From: Levin Du <djw@t-chip.com.cn>
> 
> ROC-RK3399-PC is a power efficient 4GB LPDDR4 single board
> computer with USB 3.0 and Gigabit Ethernet in a form factor
> compatible with the Raspberry Pi. It is based on the Rockchip
> RK3399 SoC, powered by the Type-C port.
> 
> The devicetree currently supports peripherals of:
> 
> - Ethernet
> - HDMI
> - SD Card
> - UART2 debug
> - Type-C
> - eMMC
> 
> USB3 in Type-C port currently only works with normal orientation,
> not flip one.
> 
> Signed-off-by: Levin Du <djw@t-chip.com.cn>
> 
> ---
> 
> Changes in v2:
> - remove custom brightness-levels (use calculated one in pwm_bl driver)
> - remove redundant 'dr_mode="otg"' in usbdrd_dwc3_0
> 
> Changes in v1:
> - remove bootargs
> - use interpolation for brightness level
> - add vcc_vbus_typec1 regulator
> - fix phy-supply of u2phy0_otg and u2phy1_otg
> - remove vcc_hub_en dummy regualtor
> - add hub_rst (changed to output high) to pinctrl status of vcc5v0_host
> - remove vsel-gpios props in fan53xx
> - remove mp8859 in i2c
> - fusb302: fix interrupt setting
> - fusb302: add vbus-supply
> - remove extcon in tcphy0 and tcphy1
> - remove #sound-dai-cells in i2s*
> - use RK_PXX style bit number for cd-gpios in SDMMC
> - clean commented status lines
> 
>  Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
>  arch/arm64/boot/dts/rockchip/Makefile              |   1 +
>  arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts     | 682 +++++++++++++++++++++
>  3 files changed, 687 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts

Reviewed-by: Rob Herring <robh@kernel.org>
Heiko Stübner Aug. 1, 2018, 11:57 a.m. UTC | #2
Am Montag, 30. Juli 2018, 04:12:01 CEST schrieb djw@t-chip.com.cn:
> From: Levin Du <djw@t-chip.com.cn>
> 
> ROC-RK3399-PC is a power efficient 4GB LPDDR4 single board
> computer with USB 3.0 and Gigabit Ethernet in a form factor
> compatible with the Raspberry Pi. It is based on the Rockchip
> RK3399 SoC, powered by the Type-C port.
> 
> The devicetree currently supports peripherals of:
> 
> - Ethernet
> - HDMI
> - SD Card
> - UART2 debug
> - Type-C
> - eMMC
> 
> USB3 in Type-C port currently only works with normal orientation,
> not flip one.
> 
> Signed-off-by: Levin Du <djw@t-chip.com.cn>

applied with Rob's review-tag.

Might still make it into 4.19 but also may have to wait for 4.20


Heiko

Patch
diff mbox series

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index acfd3c7..ab5fde8 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -59,6 +59,10 @@  Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
 
+- Firefly ROC-RK3399-PC board:
+    Required root node properties:
+      - compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
+
 - ChipSPARK PopMetal-RK3288 board:
     Required root node properties:
       - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index b0092d9..06028db 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -14,5 +14,6 @@  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-bob.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
new file mode 100644
index 0000000..13dc99c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
@@ -0,0 +1,682 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
+ */
+
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+	model = "Firefly ROC-RK3399-PC Board";
+	compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm0 0 25000 0>;
+	};
+
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk808 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+
+		/*
+		 * On the module itself this is one of these (depending
+		 * on the actual card populated):
+		 * - SDIO_RESET_L_WL_REG_ON
+		 * - PDN (power down when low)
+		 */
+		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_vbus_typec0: vcc-vbus-typec0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_vbus_typec0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	/*
+	 * should be placed inside mp8859, but not until mp8859 has
+	 * its own dt-binding.
+	 */
+	vcc12v_sys: mp8859-dcdc1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		vin-supply = <&vcc_vbus_typec0>;
+	};
+
+	/* switched by pmic_sleep */
+	vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8_s3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc12v_sys>;
+	};
+
+	/* Actually 3 regulators (host0, 1, 2) controlled by the same gpio */
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en &hub_rst>;
+		regulator-name = "vcc5v0_host";
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_vbus_typec1: vcc-vbus-typec1 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_vbus_typec1_en>;
+		regulator-name = "vcc_vbus_typec1";
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_sys: vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_sys>;
+	};
+
+	vdd_log: vdd-log {
+		compatible = "pwm-regulator";
+		pwms = <&pwm2 0 25000 1>;
+		regulator-name = "vdd_log";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1400000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_RMII_SRC>;
+	assigned-clock-parents = <&clkin_gmac>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x28>;
+	rx_delay = <0x11>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec>;
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <168>;
+	i2c-scl-falling-time-ns = <4>;
+	status = "okay";
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		vcc10-supply = <&vcc3v3_sys>;
+		vcc11-supply = <&vcc3v3_sys>;
+		vcc12-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc1v8_pmu>;
+
+		regulators {
+			vdd_center: DCDC_REG1 {
+				regulator-name = "vdd_center";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_l: DCDC_REG2 {
+				regulator-name = "vdd_cpu_l";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_codec: LDO_REG1 {
+				regulator-name = "vcca1v8_codec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_hdmi: LDO_REG2 {
+				regulator-name = "vcc1v8_hdmi";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_pmu: LDO_REG3 {
+				regulator-name = "vcc1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_sdio: LDO_REG4 {
+				regulator-name = "vcc_sdio";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3000000>;
+				};
+			};
+
+			vcca3v0_codec: LDO_REG5 {
+				regulator-name = "vcca3v0_codec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v5: LDO_REG6 {
+				regulator-name = "vcc_1v5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1500000>;
+				};
+			};
+
+			vcca0v9_hdmi: LDO_REG7 {
+				regulator-name = "vcca0v9_hdmi";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v0: LDO_REG8 {
+				regulator-name = "vcc_3v0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3000000>;
+				};
+			};
+
+			vcc3v3_s3: vcc_lan: SWITCH_REG1 {
+				regulator-name = "vcc3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_s0: SWITCH_REG2 {
+				regulator-name = "vcc3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel1_gpio>;
+		regulator-name = "vdd_cpu_b";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc3v3_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_gpio>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc3v3_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c1 {
+	i2c-scl-rising-time-ns = <300>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
+&i2c3 {
+	i2c-scl-rising-time-ns = <450>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
+&i2c4 {
+	i2c-scl-rising-time-ns = <600>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	fusb1: usb-typec@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&fusb1_int>;
+		vbus-supply = <&vcc_vbus_typec1>;
+		status = "okay";
+	};
+};
+
+&i2c7 {
+	i2c-scl-rising-time-ns = <600>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	fusb0: usb-typec@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&fusb0_int>;
+		vbus-supply = <&vcc_vbus_typec0>;
+		status = "okay";
+	};
+};
+
+&i2s0 {
+	rockchip,playback-channels = <8>;
+	rockchip,capture-channels = <8>;
+	status = "okay";
+};
+
+&i2s1 {
+	rockchip,playback-channels = <2>;
+	rockchip,capture-channels = <2>;
+	status = "okay";
+};
+
+&i2s2 {
+	status = "okay";
+};
+
+&io_domains {
+	status = "okay";
+
+	bt656-supply = <&vcc_3v0>;
+	audio-supply = <&vcca1v8_codec>;
+	sdmmc-supply = <&vcc_sdio>;
+	gpio1830-supply = <&vcc_3v0>;
+};
+
+&pmu_io_domains {
+	pmu1830-supply = <&vcc_3v0>;
+	status = "okay";
+};
+
+&pinctrl {
+	lcd-panel {
+		lcd_panel_reset: lcd-panel-reset {
+			rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		vsel1_gpio: vsel1-gpio {
+			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_gpio: vsel2-gpio {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		hub_rst: hub-rst {
+			rockchip,pins = \
+				<2 RK_PA4 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	usb-typec {
+		vcc_vbus_typec1_en: vcc-vbus-typec1-en {
+			rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	fusb30x {
+		fusb0_int: fusb0-int {
+			rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		fusb1_int: fusb1-int {
+			rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca1v8_s3>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	non-removable;
+	status = "okay";
+};
+
+&tcphy0 {
+	status = "okay";
+};
+
+&tcphy1 {
+	status = "okay";
+};
+
+&tsadc {
+	/* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-mode = <1>;
+	/* tshut polarity 0:LOW 1:HIGH */
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+
+	u2phy0_otg: otg-port {
+		phy-supply = <&vcc_vbus_typec0>;
+		status = "okay";
+	};
+
+	u2phy0_host: host-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+};
+
+&u2phy1 {
+	status = "okay";
+
+	u2phy1_otg: otg-port {
+		phy-supply = <&vcc_vbus_typec1>;
+		status = "okay";
+	};
+
+	u2phy1_host: host-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usbdrd3_0 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	status = "okay";
+};
+
+&usbdrd3_1 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};