| Message ID | 1532971214-17962-4-git-send-email-jacopo@jmondi.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | drm: rcar-du: Rework clock configuration | expand |
Hi Jacopo, Thank you for the patch. On Monday, 30 July 2018 20:20:14 EEST Jacopo Mondi wrote: > DU channels not equipped with a DPLL use an internal (aka SoC provided) or > external clock source combined with an internal divider to generate the > desired output dot clock frequency. > > The current clock selection procedure does not fully exploit the ability > of external clock sources to generate the exact dot clock frequency by > themselves, but relies instead on tuning the internal DU clock divider > only, resulting in a less precise clock generation process. > > When possible, and desirable, ask the external clock source for the exact > output dot clock frequency, and test all available clock sources (internally > generated clock, externally generated clock rounded to the closest possible > frequency, and not rounded externally generated clock) to better > approximate the desired output dot clock. I don't think you need to care about the "not rounded externally generated clock" (which incidentally isn't really about rounding, but about requesting a specific rate), for two reasons. The first one is that I don't think using whatever rate is currently programmed for the external clock will lead to a better result. There's no real reason why the current external rate would be better, other than possibly just chance, and I don't think we should rely on chance. The second reason is that it would lead to a non-deterministic behaviour. The system will boot with a default clock rate for the external source, but as soon as you set a mode, that rate could change, and will never revert back to the default. The second mode you will set will thus depend for its clock selection on the modes previously set, generating all kind of bugs difficult to reproduce. > This patch specifically targets platforms (like Salvator-X[S] and ULCBs) > where the DU's input dotclock.in is generated by the versaclock VC5 clock > source, which is capable of generating the exact rate the DU needs as pixel > clock output. > > This patch fixes higher resolution modes wich requires an high pixel clock > output currently not working on non-HDMI DU channel (as VGA 1920x1080@60Hz). > > Fixes: 1b30dbde8 "drm: rcar-du: Add support for external pixel clock" > > Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> > --- > drivers/gpu/drm/rcar-du/rcar_du_crtc.c | 96 ++++++++++++++++++++++++------ > 1 file changed, 73 insertions(+), 23 deletions(-) > > diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c > b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c index 4d7907c..0dfb28ff 100644 > --- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c > +++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c > @@ -207,12 +207,12 @@ static void rcar_du_crtc_set_display_timing(struct > rcar_du_crtc *rcrtc) { > const struct drm_display_mode *mode = &rcrtc->crtc.state->adjusted_mode; > struct rcar_du_device *rcdu = rcrtc->group->dev; > - unsigned long mode_clock = mode->clock * 1000; > + unsigned long mode_pixelclock = mode->clock * 1000; > u32 dsmr; > u32 escr; > > if (rcdu->info->dpll_ch & (1 << rcrtc->index)) { > - unsigned long target = mode_clock; > + unsigned long target = mode_pixelclock; > struct dpll_info dpll = { 0 }; > unsigned long extclk; > u32 dpllcr; > @@ -258,42 +258,92 @@ static void rcar_du_crtc_set_display_timing(struct > rcar_du_crtc *rcrtc) > > escr = ESCR_DCLKSEL_DCLKIN | div; > } else { > - unsigned long clk; > + struct du_clkin_desc { > + unsigned long dist; > + unsigned long rate; > + struct clk *clk; > + u32 escr; > + } du_clkins[3]; > + struct du_clkin_desc *du_clkin = du_clkins; > + struct du_clkin_desc *clkin_best; > + unsigned long best = -1UL; > + unsigned long pixelclock; > + unsigned long cpgrate; > u32 div; > > /* > * Compute the clock divisor and select the internal or external > * dot clock based on the requested frequency. > */ > - clk = clk_get_rate(rcrtc->clock); > - div = DIV_ROUND_CLOSEST(clk, mode_clock); > - div = clamp(div, 1U, 64U) - 1; > + cpgrate = clk_get_rate(rcrtc->clock); > + div = clamp(DIV_ROUND_CLOSEST(cpgrate, mode_pixelclock), > + 1UL, 64UL) - 1; > + pixelclock = cpgrate / (div + 1); > > - escr = ESCR_DCLKSEL_CLKS | div; > + du_clkin->dist = abs(pixelclock - mode_pixelclock); > + du_clkin->escr = ESCR_DCLKSEL_CLKS | div; > + du_clkin->clk = rcrtc->clock; > + du_clkin->rate = cpgrate; > + clkin_best = du_clkin; > > if (rcrtc->extclock) { > - unsigned long extclk; > + unsigned long roundrate; > unsigned long extrate; > - unsigned long rate; > - u32 extdiv; > - > - extclk = clk_get_rate(rcrtc->extclock); > - extdiv = DIV_ROUND_CLOSEST(extclk, mode_clock); > - extdiv = clamp(extdiv, 1U, 64U) - 1; > > - extrate = extclk / (extdiv + 1); > - rate = clk / (div + 1); > - > - if (abs((long)extrate - (long)mode_clock) < > - abs((long)rate - (long)mode_clock)) > - escr = ESCR_DCLKSEL_DCLKIN | extdiv; > + /* > + * If an external clock source is present ask it > + * for the exact dot clock rate, and test all possible > + * combinations (internal, external rounded, external > + * not rounded) to achieve the best possible clock > + * accuracy. > + */ > + extrate = clk_get_rate(rcrtc->extclock); > + roundrate = clk_round_rate(rcrtc->extclock, > + mode_pixelclock); > + > + if (roundrate == mode_pixelclock) { > + /* We can't do better than this... */ > + clk_set_rate(rcrtc->extclock, roundrate); > + escr = ESCR_DCLKSEL_DCLKIN; > + goto set_escr; > + } > > - dev_dbg(rcrtc->group->dev->dev, > - "mode clock %lu extrate %lu rate %lu ESCR 0x%08x\n", > - mode_clock, extrate, rate, escr); > + /* Test the external clock 'plain' rate. */ > + du_clkin++; > + div = clamp(DIV_ROUND_CLOSEST(extrate, mode_pixelclock), > + 1UL, 64UL) - 1; > + pixelclock = extrate / (div + 1); > + du_clkin->dist = abs(pixelclock - mode_pixelclock); > + du_clkin->escr = ESCR_DCLKSEL_DCLKIN | div; > + du_clkin->clk = rcrtc->extclock; > + du_clkin->rate = extrate; If we remove this option, there will only be two options to compare, and I think it would then be possible to keep the current code structure to simplify this patch. > + /* Test the external clock 'rounded' rate. */ > + du_clkin++; > + div = clamp(DIV_ROUND_CLOSEST(roundrate, mode_pixelclock), > + 1UL, 64UL) - 1; > + pixelclock = roundrate / (div + 1); > + du_clkin->dist = abs(pixelclock - mode_pixelclock); > + du_clkin->escr = ESCR_DCLKSEL_DCLKIN | div; > + du_clkin->clk = rcrtc->extclock; > + du_clkin->rate = roundrate; > + > + /* Find out the best approximation we got. */ > + for (; du_clkin >= du_clkins; --du_clkin) { > + if (du_clkin->dist < best) { > + best = du_clkin->dist; > + clkin_best = du_clkin; > + } > + } > + clk_set_rate(clkin_best->clk, clkin_best->rate); > } > + > + escr = clkin_best->escr; > } > > +set_escr: > + dev_err(rcrtc->group->dev->dev, "%s: ESCR 0x%08x\n", __func__, escr); > + > rcar_du_group_write(rcrtc->group, rcrtc->index % 2 ? ESCR2 : ESCR, > escr); > rcar_du_group_write(rcrtc->group, rcrtc->index % 2 ? OTAR2 : OTAR, 0);
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c index 4d7907c..0dfb28ff 100644 --- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c +++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c @@ -207,12 +207,12 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc) { const struct drm_display_mode *mode = &rcrtc->crtc.state->adjusted_mode; struct rcar_du_device *rcdu = rcrtc->group->dev; - unsigned long mode_clock = mode->clock * 1000; + unsigned long mode_pixelclock = mode->clock * 1000; u32 dsmr; u32 escr; if (rcdu->info->dpll_ch & (1 << rcrtc->index)) { - unsigned long target = mode_clock; + unsigned long target = mode_pixelclock; struct dpll_info dpll = { 0 }; unsigned long extclk; u32 dpllcr; @@ -258,42 +258,92 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc) escr = ESCR_DCLKSEL_DCLKIN | div; } else { - unsigned long clk; + struct du_clkin_desc { + unsigned long dist; + unsigned long rate; + struct clk *clk; + u32 escr; + } du_clkins[3]; + struct du_clkin_desc *du_clkin = du_clkins; + struct du_clkin_desc *clkin_best; + unsigned long best = -1UL; + unsigned long pixelclock; + unsigned long cpgrate; u32 div; /* * Compute the clock divisor and select the internal or external * dot clock based on the requested frequency. */ - clk = clk_get_rate(rcrtc->clock); - div = DIV_ROUND_CLOSEST(clk, mode_clock); - div = clamp(div, 1U, 64U) - 1; + cpgrate = clk_get_rate(rcrtc->clock); + div = clamp(DIV_ROUND_CLOSEST(cpgrate, mode_pixelclock), + 1UL, 64UL) - 1; + pixelclock = cpgrate / (div + 1); - escr = ESCR_DCLKSEL_CLKS | div; + du_clkin->dist = abs(pixelclock - mode_pixelclock); + du_clkin->escr = ESCR_DCLKSEL_CLKS | div; + du_clkin->clk = rcrtc->clock; + du_clkin->rate = cpgrate; + clkin_best = du_clkin; if (rcrtc->extclock) { - unsigned long extclk; + unsigned long roundrate; unsigned long extrate; - unsigned long rate; - u32 extdiv; - - extclk = clk_get_rate(rcrtc->extclock); - extdiv = DIV_ROUND_CLOSEST(extclk, mode_clock); - extdiv = clamp(extdiv, 1U, 64U) - 1; - extrate = extclk / (extdiv + 1); - rate = clk / (div + 1); - - if (abs((long)extrate - (long)mode_clock) < - abs((long)rate - (long)mode_clock)) - escr = ESCR_DCLKSEL_DCLKIN | extdiv; + /* + * If an external clock source is present ask it + * for the exact dot clock rate, and test all possible + * combinations (internal, external rounded, external + * not rounded) to achieve the best possible clock + * accuracy. + */ + extrate = clk_get_rate(rcrtc->extclock); + roundrate = clk_round_rate(rcrtc->extclock, + mode_pixelclock); + + if (roundrate == mode_pixelclock) { + /* We can't do better than this... */ + clk_set_rate(rcrtc->extclock, roundrate); + escr = ESCR_DCLKSEL_DCLKIN; + goto set_escr; + } - dev_dbg(rcrtc->group->dev->dev, - "mode clock %lu extrate %lu rate %lu ESCR 0x%08x\n", - mode_clock, extrate, rate, escr); + /* Test the external clock 'plain' rate. */ + du_clkin++; + div = clamp(DIV_ROUND_CLOSEST(extrate, mode_pixelclock), + 1UL, 64UL) - 1; + pixelclock = extrate / (div + 1); + du_clkin->dist = abs(pixelclock - mode_pixelclock); + du_clkin->escr = ESCR_DCLKSEL_DCLKIN | div; + du_clkin->clk = rcrtc->extclock; + du_clkin->rate = extrate; + + /* Test the external clock 'rounded' rate. */ + du_clkin++; + div = clamp(DIV_ROUND_CLOSEST(roundrate, mode_pixelclock), + 1UL, 64UL) - 1; + pixelclock = roundrate / (div + 1); + du_clkin->dist = abs(pixelclock - mode_pixelclock); + du_clkin->escr = ESCR_DCLKSEL_DCLKIN | div; + du_clkin->clk = rcrtc->extclock; + du_clkin->rate = roundrate; + + /* Find out the best approximation we got. */ + for (; du_clkin >= du_clkins; --du_clkin) { + if (du_clkin->dist < best) { + best = du_clkin->dist; + clkin_best = du_clkin; + } + } + clk_set_rate(clkin_best->clk, clkin_best->rate); } + + escr = clkin_best->escr; } +set_escr: + dev_err(rcrtc->group->dev->dev, "%s: ESCR 0x%08x\n", __func__, escr); + rcar_du_group_write(rcrtc->group, rcrtc->index % 2 ? ESCR2 : ESCR, escr); rcar_du_group_write(rcrtc->group, rcrtc->index % 2 ? OTAR2 : OTAR, 0);
DU channels not equipped with a DPLL use an internal (aka SoC provided) or external clock source combined with an internal divider to generate the desired output dot clock frequency. The current clock selection procedure does not fully exploit the ability of external clock sources to generate the exact dot clock frequency by themselves, but relies instead on tuning the internal DU clock divider only, resulting in a less precise clock generation process. When possible, and desirable, ask the external clock source for the exact output dot clock frequency, and test all available clock sources (internally generated clock, externally generated clock rounded to the closest possible frequency, and not rounded externally generated clock) to better approximate the desired output dot clock. This patch specifically targets platforms (like Salvator-X[S] and ULCBs) where the DU's input dotclock.in is generated by the versaclock VC5 clock source, which is capable of generating the exact rate the DU needs as pixel clock output. This patch fixes higher resolution modes wich requires an high pixel clock output currently not working on non-HDMI DU channel (as VGA 1920x1080@60Hz). Fixes: 1b30dbde8 "drm: rcar-du: Add support for external pixel clock" Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> --- drivers/gpu/drm/rcar-du/rcar_du_crtc.c | 96 ++++++++++++++++++++++++++-------- 1 file changed, 73 insertions(+), 23 deletions(-)