ARM: dts: qcom: Remove Arrow SD600 eval board
diff mbox series

Message ID 1542310510-21964-1-git-send-email-andy.gross@linaro.org
State New, archived
Headers show
Series
  • ARM: dts: qcom: Remove Arrow SD600 eval board
Related show

Commit Message

Andy Gross Nov. 15, 2018, 7:35 p.m. UTC
This patch removes support for the APQ8064 based Arrow SD600 eval
board.  This board was never sold publicly and had very limited
distribution.  As such, we are removing this board and no longer
going to support it.

Signed-off-by: Andy Gross <andy.gross@linaro.org>
---
 arch/arm/boot/dts/Makefile                         |   1 -
 .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi    |  53 ---
 .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 ---------------------
 3 files changed, 469 deletions(-)
 delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
 delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts

Comments

Bjorn Andersson Nov. 15, 2018, 7:45 p.m. UTC | #1
On Thu 15 Nov 11:35 PST 2018, Andy Gross wrote:

> This patch removes support for the APQ8064 based Arrow SD600 eval
> board.  This board was never sold publicly and had very limited
> distribution.  As such, we are removing this board and no longer
> going to support it.
> 
> Signed-off-by: Andy Gross <andy.gross@linaro.org>

Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Regards,
Bjorn

> ---
>  arch/arm/boot/dts/Makefile                         |   1 -
>  .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi    |  53 ---
>  .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 ---------------------
>  3 files changed, 469 deletions(-)
>  delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
>  delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b0e966d..00d6e65 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
>  	ox820-cloudengines-pogoplug-series-3.dtb
>  dtb-$(CONFIG_ARCH_QCOM) += \
>  	qcom-apq8060-dragonboard.dtb \
> -	qcom-apq8064-arrow-sd-600eval.dtb \
>  	qcom-apq8064-cm-qs600.dtb \
>  	qcom-apq8064-ifc6410.dtb \
>  	qcom-apq8064-sony-xperia-yuga.dtb \
> diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> deleted file mode 100644
> index 8df7315..0000000
> --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -&tlmm_pinmux {
> -	card_detect: card-detect {
> -		mux {
> -			pins = "gpio26";
> -			function = "gpio";
> -			bias-disable;
> -		};
> -	};
> -
> -	pcie_pins: pcie-pinmux {
> -		mux {
> -			pins = "gpio27";
> -			function = "gpio";
> -		};
> -		conf {
> -			pins = "gpio27";
> -			drive-strength = <12>;
> -			bias-disable;
> -		};
> -	};
> -
> -	user_leds: user-leds {
> -		mux {
> -			pins = "gpio3", "gpio7", "gpio10", "gpio11";
> -			function = "gpio";
> -		};
> -
> -		conf {
> -			pins = "gpio3", "gpio7", "gpio10", "gpio11";
> -			function = "gpio";
> -			output-low;
> -		};
> -	};
> -
> -	magneto_pins: magneto-pins {
> -		mux {
> -			pins = "gpio31", "gpio48";
> -			function = "gpio";
> -			bias-disable;
> -		};
> -	};
> -};
> -
> -&pm8921_mpps {
> -	mpp_leds: mpp-leds {
> -		pinconf {
> -			pins = "mpp7", "mpp8";
> -			function = "digital";
> -			output-low;
> -		};
> -	};
> -};
> diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> deleted file mode 100644
> index 76b56ea..0000000
> --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> +++ /dev/null
> @@ -1,415 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -#include "qcom-apq8064-v2.0.dtsi"
> -#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/mfd/qcom-rpm.h>
> -
> -/ {
> -	model = "Arrow Electronics, APQ8064 SD_600eval";
> -	compatible = "arrow,sd_600eval", "qcom,apq8064";
> -
> -	aliases {
> -		serial0 = &gsbi7_serial;
> -		serial1 = &gsbi1_serial;
> -		i2c0 = &gsbi2_i2c;
> -		i2c1 = &gsbi3_i2c;
> -		i2c2 = &gsbi4_i2c;
> -		i2c3 = &gsbi7_i2c;
> -		spi0 = &gsbi5_spi;
> -	};
> -
> -	regulators {
> -		compatible = "simple-bus";
> -		vph: regulator-fixed@1 {
> -			compatible = "regulator-fixed";
> -			regulator-min-microvolt = <4500000>;
> -			regulator-max-microvolt = <4500000>;
> -			regulator-name = "VPH";
> -			regulator-type = "voltage";
> -			regulator-boot-on;
> -		};
> -
> -		/* on board fixed 3.3v supply */
> -		vcc3v3: vcc3v3 {
> -			compatible = "regulator-fixed";
> -			regulator-name = "VCC3V3";
> -			regulator-min-microvolt = <3300000>;
> -			regulator-max-microvolt = <3300000>;
> -			regulator-always-on;
> -		};
> -
> -	};
> -
> -	hdmi-out {
> -		compatible = "hdmi-connector";
> -		type = "a";
> -
> -		port {
> -			hdmi_con: endpoint {
> -				remote-endpoint = <&hdmi_out>;
> -			};
> -		};
> -	};
> -
> -	soc {
> -		rpm@108000 {
> -			regulators {
> -				vdd_s1-supply = <&vph>;
> -				vdd_s2-supply = <&vph>;
> -				vdd_s3-supply = <&vph>;
> -				vdd_s4-supply = <&vph>;
> -				vdd_s5-supply = <&vph>;
> -				vdd_s6-supply = <&vph>;
> -				vdd_s7-supply = <&vph>;
> -				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
> -				vdd_l3_l15_l17-supply = <&vph>;
> -				vdd_l4_l14-supply = <&vph>;
> -				vdd_l5_l8_l16-supply = <&vph>;
> -				vdd_l6_l7-supply = <&vph>;
> -				vdd_l9_l11-supply = <&vph>;
> -				vdd_l10_l22-supply = <&vph>;
> -				vdd_l21_l23_l29-supply = <&vph>;
> -				vdd_l24-supply = <&pm8921_s1>;
> -				vdd_l25-supply = <&pm8921_s1>;
> -				vdd_l26-supply = <&pm8921_s7>;
> -				vdd_l27-supply = <&pm8921_s7>;
> -				vdd_l28-supply = <&pm8921_s7>;
> -				vin_lvs1_3_6-supply = <&pm8921_s4>;
> -				vin_lvs2-supply = <&pm8921_s1>;
> -				vin_lvs4_5_7-supply = <&pm8921_s4>;
> -
> -				s1 {
> -					regulator-always-on;
> -					regulator-min-microvolt = <1225000>;
> -					regulator-max-microvolt = <1225000>;
> -					qcom,switch-mode-frequency = <3200000>;
> -					bias-pull-down;
> -				};
> -
> -				s2 {
> -					regulator-min-microvolt = <1300000>;
> -					regulator-max-microvolt = <1300000>;
> -					qcom,switch-mode-frequency = <1600000>;
> -					bias-pull-down;
> -					regulator-always-on;
> -				};
> -
> -				s3 {
> -					regulator-min-microvolt = <1000000>;
> -					regulator-max-microvolt = <1400000>;
> -					qcom,switch-mode-frequency = <4800000>;
> -				};
> -
> -				s4 {
> -					regulator-min-microvolt	= <1800000>;
> -					regulator-max-microvolt	= <1800000>;
> -					qcom,switch-mode-frequency = <1600000>;
> -					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
> -					bias-pull-down;
> -					regulator-always-on;
> -				};
> -
> -				s7 {
> -					regulator-min-microvolt = <1300000>;
> -					regulator-max-microvolt = <1300000>;
> -					qcom,switch-mode-frequency = <3200000>;
> -				 };
> -
> -				l3 {
> -					regulator-min-microvolt = <3050000>;
> -					regulator-max-microvolt = <3300000>;
> -					bias-pull-down;
> -				};
> -
> -				l4 {
> -					regulator-min-microvolt = <1000000>;
> -					regulator-max-microvolt = <1800000>;
> -					bias-pull-down;
> -				};
> -
> -				l5 {
> -					regulator-min-microvolt = <2750000>;
> -					regulator-max-microvolt = <3000000>;
> -					bias-pull-down;
> -					regulator-boot-on;
> -					regulator-always-on;
> -				};
> -
> -				l6 {
> -					regulator-min-microvolt = <2950000>;
> -					regulator-max-microvolt = <2950000>;
> -					bias-pull-down;
> -				};
> -
> -				/**
> -				 * 1.8v required on LS expansion
> -				 * for mezzanine boards
> -				 */
> -				l15 {
> -					regulator-min-microvolt = <1800000>;
> -					regulator-max-microvolt = <1800000>;
> -					regulator-always-on;
> -				};
> -
> -				l23 {
> -					regulator-min-microvolt = <1700000>;
> -					regulator-max-microvolt = <1900000>;
> -					bias-pull-down;
> -				};
> -
> -				lvs6 {
> -					bias-pull-down;
> -				};
> -
> -				lvs7 {
> -					bias-pull-down;
> -				};
> -			};
> -		};
> -
> -		gsbi@12440000 {
> -			status = "okay";
> -			qcom,mode = <GSBI_PROT_UART_W_FC>;
> -			serial@12450000 {
> -				label = "LS-UART1";
> -				status = "okay";
> -				pinctrl-names = "default";
> -				pinctrl-0 = <&gsbi1_uart_4pins>;
> -			};
> -		};
> -
> -		gsbi@12480000 {
> -			status = "okay";
> -			qcom,mode = <GSBI_PROT_I2C>;
> -			i2c@124a0000 {
> -				/* On Low speed expansion and Sensors */
> -				label = "LS-I2C0";
> -				status = "okay";
> -				lis3mdl_mag@1e {
> -					compatible = "st,lis3mdl-magn";
> -					reg = <0x1e>;
> -					vdd-supply = <&vcc3v3>;
> -					vddio-supply = <&pm8921_s4>;
> -					pinctrl-names = "default";
> -					pinctrl-0 = <&magneto_pins>;
> -					interrupt-parent = <&tlmm_pinmux>;
> -
> -					st,drdy-int-pin = <2>;
> -					interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
> -						     <31 IRQ_TYPE_EDGE_RISING>; /* INT */
> -				};
> -			};
> -		};
> -
> -		gsbi@16200000 {
> -			status = "okay";
> -			qcom,mode = <GSBI_PROT_I2C>;
> -			i2c@16280000 {
> -			/* On Low speed expansion */
> -				status = "okay";
> -				label = "LS-I2C1";
> -				clock-frequency = <200000>;
> -				eeprom@52 {
> -					compatible = "atmel,24c128";
> -					reg = <0x52>;
> -					pagesize = <64>;
> -				};
> -			};
> -		};
> -
> -		gsbi@16300000 {
> -			status = "okay";
> -			qcom,mode = <GSBI_PROT_I2C>;
> -			i2c@16380000 {
> -				/* On High speed expansion */
> -				label = "HS-CAM-I2C3";
> -				status = "okay";
> -			};
> -		};
> -
> -		gsbi@1a200000 {
> -			status = "okay";
> -			spi@1a280000 {
> -				/* On Low speed expansion */
> -				label = "LS-SPI0";
> -				status = "okay";
> -			};
> -		};
> -
> -		/* DEBUG UART  */
> -		gsbi@16600000 {
> -			status = "okay";
> -			qcom,mode = <GSBI_PROT_I2C_UART>;
> -			serial@16640000 {
> -				label = "LS-UART0";
> -				status = "okay";
> -				pinctrl-names = "default";
> -				pinctrl-0 = <&gsbi7_uart_2pins>;
> -			};
> -
> -			i2c@16680000 {
> -				/* On High speed expansion */
> -				status = "okay";
> -				label = "HS-CAM-I2C2";
> -			};
> -		};
> -
> -		leds {
> -			pinctrl-names = "default";
> -			pinctrl-0 = <&user_leds>, <&mpp_leds>;
> -
> -			compatible = "gpio-leds";
> -
> -			user-led0 {
> -				label = "user0-led";
> -				gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
> -				linux,default-trigger = "heartbeat";
> -				default-state = "off";
> -			};
> -
> -			user-led1 {
> -				label = "user1-led";
> -				gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
> -				linux,default-trigger = "mmc0";
> -				default-state = "off";
> -			};
> -
> -			user-led2 {
> -				label = "user2-led";
> -				gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
> -				linux,default-trigger = "mmc1";
> -				default-state = "off";
> -			};
> -
> -			user-led3 {
> -				label = "user3-led";
> -				gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
> -				linux,default-trigger = "none";
> -				default-state = "off";
> -			};
> -
> -			wifi-led {
> -				label = "WiFi-led";
> -				gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
> -				default-state = "off";
> -			};
> -
> -			bt-led {
> -				label = "BT-led";
> -				gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
> -				default-state = "off";
> -			};
> -		};
> -
> -		pci@1b500000 {
> -			status = "okay";
> -			vdda-supply = <&pm8921_s3>;
> -			vdda_phy-supply = <&pm8921_lvs6>;
> -			vdda_refclk-supply = <&vcc3v3>;
> -			pinctrl-0 = <&pcie_pins>;
> -			pinctrl-names = "default";
> -			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
> -		};
> -
> -		phy@1b400000 {
> -			status = "okay";
> -		};
> -
> -		sata@29000000 {
> -			status	= "okay";
> -			target-supply	= <&pm8921_lvs7>;
> -		};
> -
> -		/* OTG */
> -		usb@12500000 {
> -			status = "okay";
> -			dr_mode = "peripheral";
> -			ulpi {
> -				phy {
> -					v3p3-supply = <&pm8921_l3>;
> -					v1p8-supply = <&pm8921_l4>;
> -				};
> -			};
> -		};
> -
> -		usb@12520000 {
> -			status = "okay";
> -			dr_mode = "otg";
> -			ulpi {
> -				phy {
> -					v3p3-supply = <&pm8921_l3>;
> -					v1p8-supply = <&pm8921_l23>;
> -				};
> -			};
> -		};
> -
> -		usb@12530000 {
> -			status = "okay";
> -			dr_mode = "otg";
> -			ulpi {
> -				phy {
> -					v3p3-supply = <&pm8921_l3>;
> -					v1p8-supply = <&pm8921_l23>;
> -				};
> -			};
> -		};
> -
> -		amba {
> -			/* eMMC */
> -			sdcc@12400000 {
> -				status = "okay";
> -				vmmc-supply = <&pm8921_l5>;
> -				vqmmc-supply = <&pm8921_s4>;
> -			};
> -
> -			/* External micro SD card */
> -			sdcc@12180000 {
> -				status = "okay";
> -				vmmc-supply = <&pm8921_l6>;
> -				pinctrl-names	= "default";
> -				pinctrl-0	= <&card_detect>;
> -				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
> -			};
> -		};
> -
> -		riva-pil@3204000 {
> -			status = "okay";
> -
> -			pinctrl-names = "default";
> -			pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
> -		};
> -
> -		hdmi-tx@4a00000 {
> -			status = "okay";
> -			core-vdda-supply = <&pm8921_hdmi_switch>;
> -			hdmi-mux-supply = <&vcc3v3>;
> -
> -			hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
> -
> -			ports {
> -				port@1 {
> -					endpoint {
> -						remote-endpoint = <&hdmi_con>;
> -					};
> -				};
> -			};
> -		};
> -
> -		hdmi-phy@4a00400 {
> -			status = "okay";
> -			core-vdda-supply = <&pm8921_hdmi_switch>;
> -		};
> -
> -		mdp@5100000 {
> -			status = "okay";
> -
> -			ports {
> -				port@3 {
> -					endpoint {
> -						remote-endpoint = <&hdmi_in>;
> -					};
> -				};
> -			};
> -		};
> -	};
> -};
> -- 
> 2.7.4
>
Nicolas Dechesne Nov. 18, 2018, 10:32 p.m. UTC | #2
On Thu, Nov 15, 2018 at 8:35 PM Andy Gross <andy.gross@linaro.org> wrote:
>
> This patch removes support for the APQ8064 based Arrow SD600 eval
> board.  This board was never sold publicly and had very limited
> distribution.  As such, we are removing this board and no longer
> going to support it.
>
> Signed-off-by: Andy Gross <andy.gross@linaro.org>

Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>

> ---
>  arch/arm/boot/dts/Makefile                         |   1 -
>  .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi    |  53 ---
>  .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 ---------------------
>  3 files changed, 469 deletions(-)
>  delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
>  delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b0e966d..00d6e65 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
>         ox820-cloudengines-pogoplug-series-3.dtb
>  dtb-$(CONFIG_ARCH_QCOM) += \
>         qcom-apq8060-dragonboard.dtb \
> -       qcom-apq8064-arrow-sd-600eval.dtb \
>         qcom-apq8064-cm-qs600.dtb \
>         qcom-apq8064-ifc6410.dtb \
>         qcom-apq8064-sony-xperia-yuga.dtb \
> diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> deleted file mode 100644
> index 8df7315..0000000
> --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -&tlmm_pinmux {
> -       card_detect: card-detect {
> -               mux {
> -                       pins = "gpio26";
> -                       function = "gpio";
> -                       bias-disable;
> -               };
> -       };
> -
> -       pcie_pins: pcie-pinmux {
> -               mux {
> -                       pins = "gpio27";
> -                       function = "gpio";
> -               };
> -               conf {
> -                       pins = "gpio27";
> -                       drive-strength = <12>;
> -                       bias-disable;
> -               };
> -       };
> -
> -       user_leds: user-leds {
> -               mux {
> -                       pins = "gpio3", "gpio7", "gpio10", "gpio11";
> -                       function = "gpio";
> -               };
> -
> -               conf {
> -                       pins = "gpio3", "gpio7", "gpio10", "gpio11";
> -                       function = "gpio";
> -                       output-low;
> -               };
> -       };
> -
> -       magneto_pins: magneto-pins {
> -               mux {
> -                       pins = "gpio31", "gpio48";
> -                       function = "gpio";
> -                       bias-disable;
> -               };
> -       };
> -};
> -
> -&pm8921_mpps {
> -       mpp_leds: mpp-leds {
> -               pinconf {
> -                       pins = "mpp7", "mpp8";
> -                       function = "digital";
> -                       output-low;
> -               };
> -       };
> -};
> diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> deleted file mode 100644
> index 76b56ea..0000000
> --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> +++ /dev/null
> @@ -1,415 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -#include "qcom-apq8064-v2.0.dtsi"
> -#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/mfd/qcom-rpm.h>
> -
> -/ {
> -       model = "Arrow Electronics, APQ8064 SD_600eval";
> -       compatible = "arrow,sd_600eval", "qcom,apq8064";
> -
> -       aliases {
> -               serial0 = &gsbi7_serial;
> -               serial1 = &gsbi1_serial;
> -               i2c0 = &gsbi2_i2c;
> -               i2c1 = &gsbi3_i2c;
> -               i2c2 = &gsbi4_i2c;
> -               i2c3 = &gsbi7_i2c;
> -               spi0 = &gsbi5_spi;
> -       };
> -
> -       regulators {
> -               compatible = "simple-bus";
> -               vph: regulator-fixed@1 {
> -                       compatible = "regulator-fixed";
> -                       regulator-min-microvolt = <4500000>;
> -                       regulator-max-microvolt = <4500000>;
> -                       regulator-name = "VPH";
> -                       regulator-type = "voltage";
> -                       regulator-boot-on;
> -               };
> -
> -               /* on board fixed 3.3v supply */
> -               vcc3v3: vcc3v3 {
> -                       compatible = "regulator-fixed";
> -                       regulator-name = "VCC3V3";
> -                       regulator-min-microvolt = <3300000>;
> -                       regulator-max-microvolt = <3300000>;
> -                       regulator-always-on;
> -               };
> -
> -       };
> -
> -       hdmi-out {
> -               compatible = "hdmi-connector";
> -               type = "a";
> -
> -               port {
> -                       hdmi_con: endpoint {
> -                               remote-endpoint = <&hdmi_out>;
> -                       };
> -               };
> -       };
> -
> -       soc {
> -               rpm@108000 {
> -                       regulators {
> -                               vdd_s1-supply = <&vph>;
> -                               vdd_s2-supply = <&vph>;
> -                               vdd_s3-supply = <&vph>;
> -                               vdd_s4-supply = <&vph>;
> -                               vdd_s5-supply = <&vph>;
> -                               vdd_s6-supply = <&vph>;
> -                               vdd_s7-supply = <&vph>;
> -                               vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
> -                               vdd_l3_l15_l17-supply = <&vph>;
> -                               vdd_l4_l14-supply = <&vph>;
> -                               vdd_l5_l8_l16-supply = <&vph>;
> -                               vdd_l6_l7-supply = <&vph>;
> -                               vdd_l9_l11-supply = <&vph>;
> -                               vdd_l10_l22-supply = <&vph>;
> -                               vdd_l21_l23_l29-supply = <&vph>;
> -                               vdd_l24-supply = <&pm8921_s1>;
> -                               vdd_l25-supply = <&pm8921_s1>;
> -                               vdd_l26-supply = <&pm8921_s7>;
> -                               vdd_l27-supply = <&pm8921_s7>;
> -                               vdd_l28-supply = <&pm8921_s7>;
> -                               vin_lvs1_3_6-supply = <&pm8921_s4>;
> -                               vin_lvs2-supply = <&pm8921_s1>;
> -                               vin_lvs4_5_7-supply = <&pm8921_s4>;
> -
> -                               s1 {
> -                                       regulator-always-on;
> -                                       regulator-min-microvolt = <1225000>;
> -                                       regulator-max-microvolt = <1225000>;
> -                                       qcom,switch-mode-frequency = <3200000>;
> -                                       bias-pull-down;
> -                               };
> -
> -                               s2 {
> -                                       regulator-min-microvolt = <1300000>;
> -                                       regulator-max-microvolt = <1300000>;
> -                                       qcom,switch-mode-frequency = <1600000>;
> -                                       bias-pull-down;
> -                                       regulator-always-on;
> -                               };
> -
> -                               s3 {
> -                                       regulator-min-microvolt = <1000000>;
> -                                       regulator-max-microvolt = <1400000>;
> -                                       qcom,switch-mode-frequency = <4800000>;
> -                               };
> -
> -                               s4 {
> -                                       regulator-min-microvolt = <1800000>;
> -                                       regulator-max-microvolt = <1800000>;
> -                                       qcom,switch-mode-frequency = <1600000>;
> -                                       qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
> -                                       bias-pull-down;
> -                                       regulator-always-on;
> -                               };
> -
> -                               s7 {
> -                                       regulator-min-microvolt = <1300000>;
> -                                       regulator-max-microvolt = <1300000>;
> -                                       qcom,switch-mode-frequency = <3200000>;
> -                                };
> -
> -                               l3 {
> -                                       regulator-min-microvolt = <3050000>;
> -                                       regulator-max-microvolt = <3300000>;
> -                                       bias-pull-down;
> -                               };
> -
> -                               l4 {
> -                                       regulator-min-microvolt = <1000000>;
> -                                       regulator-max-microvolt = <1800000>;
> -                                       bias-pull-down;
> -                               };
> -
> -                               l5 {
> -                                       regulator-min-microvolt = <2750000>;
> -                                       regulator-max-microvolt = <3000000>;
> -                                       bias-pull-down;
> -                                       regulator-boot-on;
> -                                       regulator-always-on;
> -                               };
> -
> -                               l6 {
> -                                       regulator-min-microvolt = <2950000>;
> -                                       regulator-max-microvolt = <2950000>;
> -                                       bias-pull-down;
> -                               };
> -
> -                               /**
> -                                * 1.8v required on LS expansion
> -                                * for mezzanine boards
> -                                */
> -                               l15 {
> -                                       regulator-min-microvolt = <1800000>;
> -                                       regulator-max-microvolt = <1800000>;
> -                                       regulator-always-on;
> -                               };
> -
> -                               l23 {
> -                                       regulator-min-microvolt = <1700000>;
> -                                       regulator-max-microvolt = <1900000>;
> -                                       bias-pull-down;
> -                               };
> -
> -                               lvs6 {
> -                                       bias-pull-down;
> -                               };
> -
> -                               lvs7 {
> -                                       bias-pull-down;
> -                               };
> -                       };
> -               };
> -
> -               gsbi@12440000 {
> -                       status = "okay";
> -                       qcom,mode = <GSBI_PROT_UART_W_FC>;
> -                       serial@12450000 {
> -                               label = "LS-UART1";
> -                               status = "okay";
> -                               pinctrl-names = "default";
> -                               pinctrl-0 = <&gsbi1_uart_4pins>;
> -                       };
> -               };
> -
> -               gsbi@12480000 {
> -                       status = "okay";
> -                       qcom,mode = <GSBI_PROT_I2C>;
> -                       i2c@124a0000 {
> -                               /* On Low speed expansion and Sensors */
> -                               label = "LS-I2C0";
> -                               status = "okay";
> -                               lis3mdl_mag@1e {
> -                                       compatible = "st,lis3mdl-magn";
> -                                       reg = <0x1e>;
> -                                       vdd-supply = <&vcc3v3>;
> -                                       vddio-supply = <&pm8921_s4>;
> -                                       pinctrl-names = "default";
> -                                       pinctrl-0 = <&magneto_pins>;
> -                                       interrupt-parent = <&tlmm_pinmux>;
> -
> -                                       st,drdy-int-pin = <2>;
> -                                       interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
> -                                                    <31 IRQ_TYPE_EDGE_RISING>; /* INT */
> -                               };
> -                       };
> -               };
> -
> -               gsbi@16200000 {
> -                       status = "okay";
> -                       qcom,mode = <GSBI_PROT_I2C>;
> -                       i2c@16280000 {
> -                       /* On Low speed expansion */
> -                               status = "okay";
> -                               label = "LS-I2C1";
> -                               clock-frequency = <200000>;
> -                               eeprom@52 {
> -                                       compatible = "atmel,24c128";
> -                                       reg = <0x52>;
> -                                       pagesize = <64>;
> -                               };
> -                       };
> -               };
> -
> -               gsbi@16300000 {
> -                       status = "okay";
> -                       qcom,mode = <GSBI_PROT_I2C>;
> -                       i2c@16380000 {
> -                               /* On High speed expansion */
> -                               label = "HS-CAM-I2C3";
> -                               status = "okay";
> -                       };
> -               };
> -
> -               gsbi@1a200000 {
> -                       status = "okay";
> -                       spi@1a280000 {
> -                               /* On Low speed expansion */
> -                               label = "LS-SPI0";
> -                               status = "okay";
> -                       };
> -               };
> -
> -               /* DEBUG UART  */
> -               gsbi@16600000 {
> -                       status = "okay";
> -                       qcom,mode = <GSBI_PROT_I2C_UART>;
> -                       serial@16640000 {
> -                               label = "LS-UART0";
> -                               status = "okay";
> -                               pinctrl-names = "default";
> -                               pinctrl-0 = <&gsbi7_uart_2pins>;
> -                       };
> -
> -                       i2c@16680000 {
> -                               /* On High speed expansion */
> -                               status = "okay";
> -                               label = "HS-CAM-I2C2";
> -                       };
> -               };
> -
> -               leds {
> -                       pinctrl-names = "default";
> -                       pinctrl-0 = <&user_leds>, <&mpp_leds>;
> -
> -                       compatible = "gpio-leds";
> -
> -                       user-led0 {
> -                               label = "user0-led";
> -                               gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
> -                               linux,default-trigger = "heartbeat";
> -                               default-state = "off";
> -                       };
> -
> -                       user-led1 {
> -                               label = "user1-led";
> -                               gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
> -                               linux,default-trigger = "mmc0";
> -                               default-state = "off";
> -                       };
> -
> -                       user-led2 {
> -                               label = "user2-led";
> -                               gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
> -                               linux,default-trigger = "mmc1";
> -                               default-state = "off";
> -                       };
> -
> -                       user-led3 {
> -                               label = "user3-led";
> -                               gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
> -                               linux,default-trigger = "none";
> -                               default-state = "off";
> -                       };
> -
> -                       wifi-led {
> -                               label = "WiFi-led";
> -                               gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
> -                               default-state = "off";
> -                       };
> -
> -                       bt-led {
> -                               label = "BT-led";
> -                               gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
> -                               default-state = "off";
> -                       };
> -               };
> -
> -               pci@1b500000 {
> -                       status = "okay";
> -                       vdda-supply = <&pm8921_s3>;
> -                       vdda_phy-supply = <&pm8921_lvs6>;
> -                       vdda_refclk-supply = <&vcc3v3>;
> -                       pinctrl-0 = <&pcie_pins>;
> -                       pinctrl-names = "default";
> -                       perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
> -               };
> -
> -               phy@1b400000 {
> -                       status = "okay";
> -               };
> -
> -               sata@29000000 {
> -                       status  = "okay";
> -                       target-supply   = <&pm8921_lvs7>;
> -               };
> -
> -               /* OTG */
> -               usb@12500000 {
> -                       status = "okay";
> -                       dr_mode = "peripheral";
> -                       ulpi {
> -                               phy {
> -                                       v3p3-supply = <&pm8921_l3>;
> -                                       v1p8-supply = <&pm8921_l4>;
> -                               };
> -                       };
> -               };
> -
> -               usb@12520000 {
> -                       status = "okay";
> -                       dr_mode = "otg";
> -                       ulpi {
> -                               phy {
> -                                       v3p3-supply = <&pm8921_l3>;
> -                                       v1p8-supply = <&pm8921_l23>;
> -                               };
> -                       };
> -               };
> -
> -               usb@12530000 {
> -                       status = "okay";
> -                       dr_mode = "otg";
> -                       ulpi {
> -                               phy {
> -                                       v3p3-supply = <&pm8921_l3>;
> -                                       v1p8-supply = <&pm8921_l23>;
> -                               };
> -                       };
> -               };
> -
> -               amba {
> -                       /* eMMC */
> -                       sdcc@12400000 {
> -                               status = "okay";
> -                               vmmc-supply = <&pm8921_l5>;
> -                               vqmmc-supply = <&pm8921_s4>;
> -                       };
> -
> -                       /* External micro SD card */
> -                       sdcc@12180000 {
> -                               status = "okay";
> -                               vmmc-supply = <&pm8921_l6>;
> -                               pinctrl-names   = "default";
> -                               pinctrl-0       = <&card_detect>;
> -                               cd-gpios        = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
> -                       };
> -               };
> -
> -               riva-pil@3204000 {
> -                       status = "okay";
> -
> -                       pinctrl-names = "default";
> -                       pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
> -               };
> -
> -               hdmi-tx@4a00000 {
> -                       status = "okay";
> -                       core-vdda-supply = <&pm8921_hdmi_switch>;
> -                       hdmi-mux-supply = <&vcc3v3>;
> -
> -                       hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
> -
> -                       ports {
> -                               port@1 {
> -                                       endpoint {
> -                                               remote-endpoint = <&hdmi_con>;
> -                                       };
> -                               };
> -                       };
> -               };
> -
> -               hdmi-phy@4a00400 {
> -                       status = "okay";
> -                       core-vdda-supply = <&pm8921_hdmi_switch>;
> -               };
> -
> -               mdp@5100000 {
> -                       status = "okay";
> -
> -                       ports {
> -                               port@3 {
> -                                       endpoint {
> -                                               remote-endpoint = <&hdmi_in>;
> -                                       };
> -                               };
> -                       };
> -               };
> -       };
> -};
> --
> 2.7.4
>
Olof Johansson Nov. 18, 2018, 11:29 p.m. UTC | #3
On Thu, Nov 15, 2018 at 11:35 AM Andy Gross <andy.gross@linaro.org> wrote:
>
> This patch removes support for the APQ8064 based Arrow SD600 eval
> board.  This board was never sold publicly and had very limited
> distribution.  As such, we are removing this board and no longer
> going to support it.
>
> Signed-off-by: Andy Gross <andy.gross@linaro.org>

It's currently throwing DTS warnings as well, so if nobody's
interested in keeping it around, this seems OK with me.

Acked-by: Olof Johansson <olof@lixom.net>


-Olof

Patch
diff mbox series

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d..00d6e65 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -783,7 +783,6 @@  dtb-$(CONFIG_ARCH_OXNAS) += \
 	ox820-cloudengines-pogoplug-series-3.dtb
 dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-apq8060-dragonboard.dtb \
-	qcom-apq8064-arrow-sd-600eval.dtb \
 	qcom-apq8064-cm-qs600.dtb \
 	qcom-apq8064-ifc6410.dtb \
 	qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
deleted file mode 100644
index 8df7315..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
+++ /dev/null
@@ -1,53 +0,0 @@ 
-// SPDX-License-Identifier: GPL-2.0
-&tlmm_pinmux {
-	card_detect: card-detect {
-		mux {
-			pins = "gpio26";
-			function = "gpio";
-			bias-disable;
-		};
-	};
-
-	pcie_pins: pcie-pinmux {
-		mux {
-			pins = "gpio27";
-			function = "gpio";
-		};
-		conf {
-			pins = "gpio27";
-			drive-strength = <12>;
-			bias-disable;
-		};
-	};
-
-	user_leds: user-leds {
-		mux {
-			pins = "gpio3", "gpio7", "gpio10", "gpio11";
-			function = "gpio";
-		};
-
-		conf {
-			pins = "gpio3", "gpio7", "gpio10", "gpio11";
-			function = "gpio";
-			output-low;
-		};
-	};
-
-	magneto_pins: magneto-pins {
-		mux {
-			pins = "gpio31", "gpio48";
-			function = "gpio";
-			bias-disable;
-		};
-	};
-};
-
-&pm8921_mpps {
-	mpp_leds: mpp-leds {
-		pinconf {
-			pins = "mpp7", "mpp8";
-			function = "digital";
-			output-low;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
deleted file mode 100644
index 76b56ea..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ /dev/null
@@ -1,415 +0,0 @@ 
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-
-/ {
-	model = "Arrow Electronics, APQ8064 SD_600eval";
-	compatible = "arrow,sd_600eval", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi7_serial;
-		serial1 = &gsbi1_serial;
-		i2c0 = &gsbi2_i2c;
-		i2c1 = &gsbi3_i2c;
-		i2c2 = &gsbi4_i2c;
-		i2c3 = &gsbi7_i2c;
-		spi0 = &gsbi5_spi;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		vph: regulator-fixed@1 {
-			compatible = "regulator-fixed";
-			regulator-min-microvolt = <4500000>;
-			regulator-max-microvolt = <4500000>;
-			regulator-name = "VPH";
-			regulator-type = "voltage";
-			regulator-boot-on;
-		};
-
-		/* on board fixed 3.3v supply */
-		vcc3v3: vcc3v3 {
-			compatible = "regulator-fixed";
-			regulator-name = "VCC3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con: endpoint {
-				remote-endpoint = <&hdmi_out>;
-			};
-		};
-	};
-
-	soc {
-		rpm@108000 {
-			regulators {
-				vdd_s1-supply = <&vph>;
-				vdd_s2-supply = <&vph>;
-				vdd_s3-supply = <&vph>;
-				vdd_s4-supply = <&vph>;
-				vdd_s5-supply = <&vph>;
-				vdd_s6-supply = <&vph>;
-				vdd_s7-supply = <&vph>;
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l3_l15_l17-supply = <&vph>;
-				vdd_l4_l14-supply = <&vph>;
-				vdd_l5_l8_l16-supply = <&vph>;
-				vdd_l6_l7-supply = <&vph>;
-				vdd_l9_l11-supply = <&vph>;
-				vdd_l10_l22-supply = <&vph>;
-				vdd_l21_l23_l29-supply = <&vph>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				 };
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				/**
-				 * 1.8v required on LS expansion
-				 * for mezzanine boards
-				 */
-				l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-
-				lvs7 {
-					bias-pull-down;
-				};
-			};
-		};
-
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_UART_W_FC>;
-			serial@12450000 {
-				label = "LS-UART1";
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi1_uart_4pins>;
-			};
-		};
-
-		gsbi@12480000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@124a0000 {
-				/* On Low speed expansion and Sensors */
-				label = "LS-I2C0";
-				status = "okay";
-				lis3mdl_mag@1e {
-					compatible = "st,lis3mdl-magn";
-					reg = <0x1e>;
-					vdd-supply = <&vcc3v3>;
-					vddio-supply = <&pm8921_s4>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&magneto_pins>;
-					interrupt-parent = <&tlmm_pinmux>;
-
-					st,drdy-int-pin = <2>;
-					interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
-						     <31 IRQ_TYPE_EDGE_RISING>; /* INT */
-				};
-			};
-		};
-
-		gsbi@16200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16280000 {
-			/* On Low speed expansion */
-				status = "okay";
-				label = "LS-I2C1";
-				clock-frequency = <200000>;
-				eeprom@52 {
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					pagesize = <64>;
-				};
-			};
-		};
-
-		gsbi@16300000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16380000 {
-				/* On High speed expansion */
-				label = "HS-CAM-I2C3";
-				status = "okay";
-			};
-		};
-
-		gsbi@1a200000 {
-			status = "okay";
-			spi@1a280000 {
-				/* On Low speed expansion */
-				label = "LS-SPI0";
-				status = "okay";
-			};
-		};
-
-		/* DEBUG UART  */
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				label = "LS-UART0";
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
-
-			i2c@16680000 {
-				/* On High speed expansion */
-				status = "okay";
-				label = "HS-CAM-I2C2";
-			};
-		};
-
-		leds {
-			pinctrl-names = "default";
-			pinctrl-0 = <&user_leds>, <&mpp_leds>;
-
-			compatible = "gpio-leds";
-
-			user-led0 {
-				label = "user0-led";
-				gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "heartbeat";
-				default-state = "off";
-			};
-
-			user-led1 {
-				label = "user1-led";
-				gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "mmc0";
-				default-state = "off";
-			};
-
-			user-led2 {
-				label = "user2-led";
-				gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "mmc1";
-				default-state = "off";
-			};
-
-			user-led3 {
-				label = "user3-led";
-				gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "none";
-				default-state = "off";
-			};
-
-			wifi-led {
-				label = "WiFi-led";
-				gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-
-			bt-led {
-				label = "BT-led";
-				gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-		};
-
-		pci@1b500000 {
-			status = "okay";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&vcc3v3>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
-		};
-
-		phy@1b400000 {
-			status = "okay";
-		};
-
-		sata@29000000 {
-			status	= "okay";
-			target-supply	= <&pm8921_lvs7>;
-		};
-
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "peripheral";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		amba {
-			/* eMMC */
-			sdcc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			/* External micro SD card */
-			sdcc@12180000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l6>;
-				pinctrl-names	= "default";
-				pinctrl-0	= <&card_detect>;
-				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
-			};
-		};
-
-		riva-pil@3204000 {
-			status = "okay";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
-		};
-
-		hdmi-tx@4a00000 {
-			status = "okay";
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-			hdmi-mux-supply = <&vcc3v3>;
-
-			hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
-
-			ports {
-				port@1 {
-					endpoint {
-						remote-endpoint = <&hdmi_con>;
-					};
-				};
-			};
-		};
-
-		hdmi-phy@4a00400 {
-			status = "okay";
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-		};
-
-		mdp@5100000 {
-			status = "okay";
-
-			ports {
-				port@3 {
-					endpoint {
-						remote-endpoint = <&hdmi_in>;
-					};
-				};
-			};
-		};
-	};
-};