diff mbox series

[2/2] ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin

Message ID 20181211194251.12988-2-martyn.welch@collabora.com (mailing list archive)
State New, archived
Headers show
Series [1/2] dt-bindings: Add vendor prefix for Catalyst Semiconductor | expand

Commit Message

Martyn Welch Dec. 11, 2018, 7:42 p.m. UTC
The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an
i.MX6UL or i.MX6ULL SOM and various add-on boards.

The following adds support for the "Full Featured" version of the Segin,
which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation
module.

Its hardware specifications are:

 * 512MB DDR3 memory
 * 512MB NAND flash
 * Dual 10/100 Ethernet
 * USB Host and USB OTG
 * RS232
 * MicroSD external storage
 * Audio, RS232, I2C, SPI, CAN headers
 * Further I/O options via A/V and Expansion headers

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>

---

 arch/arm/boot/dts/Makefile                    |   1 +
 arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi   | 152 ++++++++
 .../boot/dts/imx6ul-phytec-peb-eval-01.dtsi   |  55 +++
 .../dts/imx6ul-phytec-phyboard-segin-full.dts | 103 ++++++
 .../dts/imx6ul-phytec-phyboard-segin.dtsi     | 341 ++++++++++++++++++
 5 files changed, 652 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi
 create mode 100644 arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi
 create mode 100644 arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts
 create mode 100644 arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi

Comments

Shawn Guo Jan. 10, 2019, 8:07 a.m. UTC | #1
On Tue, Dec 11, 2018 at 07:42:51PM +0000, Martyn Welch wrote:
> The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an
> i.MX6UL or i.MX6ULL SOM and various add-on boards.
> 
> The following adds support for the "Full Featured" version of the Segin,
> which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation
> module.
> 
> Its hardware specifications are:
> 
>  * 512MB DDR3 memory
>  * 512MB NAND flash
>  * Dual 10/100 Ethernet
>  * USB Host and USB OTG
>  * RS232
>  * MicroSD external storage
>  * Audio, RS232, I2C, SPI, CAN headers
>  * Further I/O options via A/V and Expansion headers
> 
> Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
> 
> ---
> 
>  arch/arm/boot/dts/Makefile                    |   1 +
>  arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi   | 152 ++++++++
>  .../boot/dts/imx6ul-phytec-peb-eval-01.dtsi   |  55 +++
>  .../dts/imx6ul-phytec-phyboard-segin-full.dts | 103 ++++++
>  .../dts/imx6ul-phytec-phyboard-segin.dtsi     | 341 ++++++++++++++++++
>  5 files changed, 652 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi
>  create mode 100644 arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi
>  create mode 100644 arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts
>  create mode 100644 arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b0e966d625b9..6ca286f6b37c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -557,6 +557,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
>  	imx6ul-liteboard.dtb \
>  	imx6ul-opos6uldev.dtb \
>  	imx6ul-pico-hobbit.dtb \
> +	imx6ul-phytec-phyboard-segin-full.dtb \
>  	imx6ul-tx6ul-0010.dtb \
>  	imx6ul-tx6ul-0011.dtb \
>  	imx6ul-tx6ul-mainboard.dtb \
> diff --git a/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi b/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi
> new file mode 100644
> index 000000000000..ede24105044f
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi
> @@ -0,0 +1,152 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> + * Author: Christian Hemp <c.hemp@phytec.de>
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include "imx6ul.dtsi"
> +
> +/ {
> +
> +	model = "Phytec phyCORE i.MX6 UltraLite";
> +	compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
> +
> +	chosen {
> +		stdout-path = &uart1;
> +	};
> +
> +

One newline is enough.

> +	/*
> +	 * Set the minimum memory size here and
> +	 * let the bootloader set the real size.
> +	 */
> +	memory {
> +		reg = <0x80000000 0x8000000>;
> +	};
> +
> +	gpio_leds_som: somleds {

leds for node name?

> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpioleds_som>;
> +		compatible = "gpio-leds";
> +		status = "okay";

The okay status is generally used to flip the disabled devices.

> +
> +		som_green {

led-green?

> +			label = "phycore:green";
> +			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
> +};
> +
> +&fec1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet1>;
> +	phy-mode = "rmii";
> +	phy-handle = <&ethphy0>;
> +	status = "okay";
> +
> +	mdio: mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@1 {
> +			reg = <1>;
> +			interrupt-parent = <&gpio1>;
> +			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> +			micrel,led-mode = <1>;
> +			clocks = <&clks IMX6UL_CLK_ENET_REF>;
> +			clock-names = "rmii-ref";
> +		};
> +	};
> +};
> +
> +&gpmi {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_gpmi_nand>;
> +	nand-on-flash-bbt;
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 =<&pinctrl_i2c1>;
> +	clock-frequency = <100000>;
> +	status = "okay";
> +
> +	eeprom@52 {
> +		compatible = "catalyst,24c32", "atmel,24c32";
> +		reg = <0x52>;
> +	};
> +};
> +
> +&snvs_poweroff {
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +
> +	pinctrl_enet1: enet1grp {
> +		fsl,pins = <
> +			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
> +			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
> +			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
> +			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
> +			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
> +			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
> +			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
> +			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
> +			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
> +			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
> +			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x17059
> +		>;
> +	};
> +
> +	pinctrl_gpioleds_som: gpioledssomgrp {
> +		fsl,pins = <MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x0b0b0>;
> +	};
> +
> +	pinctrl_gpmi_nand: gpminandgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x0b0b1
> +			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x0b0b1
> +			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0x0b0b1
> +			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x0b000
> +			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x0b0b1
> +			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x0b0b1
> +			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x0b0b1
> +			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x0b0b1
> +			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x0b0b1
> +			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x0b0b1
> +			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x0b0b1
> +			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x0b0b1
> +			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x0b0b1
> +			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0x0b0b1
> +			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x0b0b1
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2cgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL	0x4001b8b0
> +			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA	0x4001b8b0
> +		>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
> +			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
> +		>;
> +	};
> +
> +};
> diff --git a/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi b/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi
> new file mode 100644
> index 000000000000..e7d115b0ff80
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi
> @@ -0,0 +1,55 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2016 PHYTEC Messtechnik
> + * Author: Christian Hemp <c.hemp@phytec.de>
> + */
> +
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	gpio_keys: gpio-keys {
> +		compatible = "gpio-key";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_keys>;
> +		status = "disabled";
> +
> +		power {
> +			label = "Power Button";
> +			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_POWER>;
> +			gpio-key,wakeup;

The property is deprecated.  Use wakeup-source instead.

> +		};
> +	};
> +
> +	user_leds: user_leds {

leds.

> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_user_leds>;
> +		status = "disabled";
> +
> +		user_led_yellow {

led-yellow

> +			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "default-on";
> +		};
> +
> +		user_led_red {

led-red.

> +			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "default-on";
> +		};
> +	};
> +};
> +
> +&iomuxc {
> +	pinctrl_gpio_keys: gpio_keysgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x79
> +		>;
> +	};
> +
> +	pinctrl_user_leds: user_ledsgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0x79
> +			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x79
> +		>;
> +	};
> +};
> diff --git a/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts
> new file mode 100644
> index 000000000000..4bee97a4e950
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts
> @@ -0,0 +1,103 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> + * Author: Christian Hemp <c.hemp@phytec.de>
> + */
> +
> +/dts-v1/;
> +#include "imx6ul-phytec-pcl063.dtsi"
> +#include "imx6ul-phytec-phyboard-segin.dtsi"
> +#include "imx6ul-phytec-peb-eval-01.dtsi"
> +
> +/ {
> +
> +	model = "Phytec phyBOARD-Segin i.MX6 UltraLite Full Featured";
> +	compatible = "phytec,imx6ul-pbacd10", "phytec,imx6ul-pcl063",
> +		     "fsl,imx6ul";
> +};
> +
> +&adc1 {
> +	status = "okay";
> +};
> +
> +&can1 {
> +	status = "okay";
> +};
> +
> +&codec {
> +	status = "okay";
> +};
> +
> +&fec2 {
> +	status = "okay";
> +};
> +
> +&i2c_rtc {
> +	status = "okay";
> +};
> +
> +&reg_can1_en {
> +	status = "okay";
> +};
> +
> +&reg_sound_1v8 {
> +	status = "okay";
> +};
> +
> +&reg_sound_3v3 {
> +	status = "okay";
> +};
> +
> +&sai2 {
> +	status = "okay";
> +};
> +
> +&sound {
> +	status = "okay";
> +};
> +
> +&uart5 {
> +	status = "okay";
> +};
> +
> +&usbotg1 {
> +	status = "okay";
> +};
> +
> +&usbotg2 {
> +	status = "okay";
> +};
> +
> +&usdhc1 {
> +	status = "okay";
> +};
> +
> +

One newline.

> +&ecspi3 {

Sort the node properly.  The only exception could be iomuxc node with
lots of pin data.

> +	status = "okay";

We usually put status at the end of property list.

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi3>;
> +

Unnecessary newline.

> +	fsl,spi-num-chipselects=<0>;

Obsolete property.

> +	cs-gpios = <0>;

Invalid GPIO specifier.

> +
> +	spidev@0 {
> +		compatible = "spidev";
> +		spi-max-frequency = <20000000>;
> +		reg = <0>;
> +	};
> +
> +};
> +
> +

One newline.

> +&iomuxc {
> +	pinctrl_ecspi3: ecspi3grp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b0
> +			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b0
> +			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b0
> +			MX6UL_PAD_UART2_TX_DATA__ECSPI3_SS0 0x10b0
> +		>;
> +	};
> +};
> +
> diff --git a/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi
> new file mode 100644
> index 000000000000..3e59f49ce5cc
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi
> @@ -0,0 +1,341 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> + * Author: Christian Hemp <c.hemp@phytec.de>
> + */
> +
> +/ {
> +
> +	model = "Phytec phyBOARD-Segin i.MX6 UltraLite";
> +	compatible = "phytec,imx6ul-pbacd-10", "phytec,imx6ul-pcl063",
> +		     "fsl,imx6ul";
> +
> +	aliases {
> +		rtc0 = &i2c_rtc;
> +		rtc1 = &snvs_rtc;
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";

Drop this container node and put the regulator node directly under root
with unique name.

	reg_xxx: regulator-xxx {
		...
	};

> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		reg_sound_1v8: regulator@1 {
> +			compatible = "regulator-fixed";
> +			reg = <1>;
> +			regulator-name = "i2s-audio-1v8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			status = "disabled";
> +		};
> +
> +		reg_sound_3v3: regulator@2 {
> +			compatible = "regulator-fixed";
> +			reg = <2>;
> +			regulator-name = "i2s-audio-3v3";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			status = "disabled";
> +		};
> +
> +		reg_can1_en: regulator@3 {
> +			compatible = "regulator-fixed";
> +			reg = <3>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&princtrl_flexcan1_en>;
> +			regulator-name = "Can";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +			status = "disabled";
> +		};
> +
> +		reg_adc1_vref_3v3: regulator@5 {
> +			compatible = "regulator-fixed";
> +			regulator-name = "vref-3v3";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +		};
> +	};
> +
> +	sound: sound {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,name = "phyBOARD-Segin-TLV320AIC3007";
> +		simple-audio-card,format = "i2s";
> +		simple-audio-card,bitclock-master = <&dailink_master>;
> +		simple-audio-card,frame-master = <&dailink_master>;
> +		simple-audio-card,widgets =
> +			"Line", "Line In",
> +			"Line", "Line Out",
> +			"Speaker", "Speaker";
> +		simple-audio-card,routing =
> +			"Line Out", "LLOUT",
> +			"Line Out", "RLOUT",
> +			"Speaker", "SPOP",
> +			"Speaker", "SPOM",
> +			"LINE1L", "Line In",
> +			"LINE1R", "Line In";
> +		status = "disabled";
> +
> +		simple-audio-card,cpu {
> +			sound-dai = <&sai2>;
> +		};
> +
> +		dailink_master: simple-audio-card,codec {
> +			sound-dai = <&codec>;
> +			clocks = <&clks IMX6UL_CLK_SAI2>;
> +		};
> +	};
> +
> +};
> +
> +&can1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan1>;
> +	xceiver-supply = <&reg_can1_en>;
> +	status = "disabled";
> +};
> +
> +&clks {
> +	assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
> +	assigned-clock-rates = <786432000>;
> +};
> +
> +&fec2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet2>;
> +	phy-mode = "rmii";
> +	phy-handle = <&ethphy1>;
> +	status = "disabled";
> +};
> +
> +&i2c1 {
> +	codec: tlv320@18 {
> +		compatible = "ti,tlv320aic3007";
> +		#sound-dai-cells = <0>;
> +		reg = <0x18>;
> +

Drop the newline.

> +		AVDD-supply = <&reg_sound_3v3>;
> +		IOVDD-supply = <&reg_sound_3v3>;
> +		DRVDD-supply = <&reg_sound_3v3>;
> +		DVDD-supply = <&reg_sound_1v8>;
> +		status = "disabled";
> +	};
> +
> +	stmpe: stmpe@44 {
> +		compatible = "st,stmpe811";
> +		reg = <0x44>;
> +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-parent = <&gpio5>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_stmpe>;
> +		status = "disabled";
> +
> +		stmpe_touchscreen {

touchscreen

> +			compatible = "st,stmpe-ts";
> +			st,sample-time = <4>;
> +			st,mod-12b = <1>;
> +			st,ref-sel = <0>;
> +			st,adc-freq = <1>;
> +			st,ave-ctrl = <1>;
> +			st,touch-det-delay = <2>;
> +			st,settling = <2>;
> +			st,fraction-z = <7>;
> +			st,i-drive = <1>;
> +			touchscreen-inverted-x = <1>;
> +			touchscreen-inverted-y = <1>;
> +		};
> +	};
> +
> +	i2c_rtc: rtc@68 {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_rtc_int>;
> +		compatible = "microcrystal,rv4162";
> +		reg = <0x68>;
> +		interrupt-parent = <&gpio5>;
> +		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
> +		status = "disabled";
> +	};
> +};
> +
> +&mdio {
> +	ethphy1: ethernet-phy@2 {
> +		reg = <2>;
> +		micrel,led-mode = <1>;
> +		clocks = <&clks IMX6UL_CLK_ENET2_REF>;
> +		clock-names = "rmii-ref";
> +	};
> +};
> +
> +&pwm3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm3>;
> +	status = "disabled";
> +};
> +
> +&sai2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_sai2>;
> +	assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
> +			<&clks IMX6UL_CLK_SAI2>;
> +	assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
> +	assigned-clock-rates = <0>, <19200000>;
> +	fsl,sai-mclk-direction-output;
> +	status = "disabled";
> +};
> +
> +&uart5 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart5>;
> +	uart-has-rtscts;
> +	status = "disabled";
> +};
> +
> +&usbotg1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb_otg1_id>;
> +	dr_mode = "otg";
> +	status = "disabled";
> +};
> +
> +&usbotg2 {
> +	dr_mode = "host";
> +	disable-over-current;
> +	status = "disabled";
> +};
> +
> +&usdhc1 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> +	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
> +	no-1-8-v;
> +	keep-power-in-suspend;
> +	wakeup-source;
> +	status = "disabled";
> +};
> +
> +&adc1 {

Sort it properly.

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_adc1>;
> +	vref-supply = <&reg_adc1_vref_3v3>;
> +	status = "disabled";

Put it at the end of properties.

> +	/*
> +	 * driver can not separate a specific channel so we request 4 channels
> +	 * here - we need only the fourth channel
> +	 */
> +	num-channels = <4>;
> +};
> +
> +&iomuxc {
> +	pinctrl_enet2: enet2grp {
> +		fsl,pins = <
> +			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
> +			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
> +			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
> +			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
> +			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
> +			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
> +			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
> +			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
> +		>;
> +	};
> +
> +	pinctrl_flexcan1: flexcan1 {
> +		fsl,pins = <
> +			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x0b0b0
> +			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x0b0b0
> +		>;
> +	};
> +
> +	princtrl_flexcan1_en: flexcan1engrp {
> +		fsl,pins = <
> +			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x17059
> +		>;
> +	};
> +
> +	pinctrl_pwm3: pwm3grp {
> +		fsl,pins = <
> +			MX6UL_PAD_GPIO1_IO04__PWM3_OUT	0x0b0b0
> +		>;
> +	};
> +
> +	pinctrl_rtc_int: rtcintgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17059
> +		>;
> +	};
> +
> +	pinctrl_sai2: sai2grp {
> +		fsl,pins = <
> +			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
> +			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
> +			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x11088
> +			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x11088
> +			MX6UL_PAD_JTAG_TMS__SAI2_MCLK		0x17088
> +		>;
> +	};
> +
> +	pinctrl_stmpe: stmpegrp {
> +		fsl,pins = <
> +			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
> +		>;
> +	};
> +
> +	pinctrl_uart5: uart5grp {
> +		fsl,pins = <
> +			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
> +			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
> +			MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS	0x1b0b1
> +			MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_usb_otg1_id: usbotg1idgrp {
> +		fsl,pins = <
> +			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
> +		>;
> +	};
> +
> +	pinctrl_usdhc1: usdhc1grp {
> +		fsl,pins = <
> +			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
> +			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
> +			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
> +			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
> +			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
> +			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
> +			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> +		fsl,pins = <
> +			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
> +			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
> +			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
> +			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
> +			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
> +			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
> +		>;
> +	};
> +
> +	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> +		fsl,pins = <
> +			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
> +			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
> +			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
> +			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
> +			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
> +			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
> +		>;
> +	};
> +
> +	pinctrl_adc1: adc1grp {

Sort it properly.

Shawn

> +		fsl,pins = <
> +			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
> +		>;
> +	};
> +};
> -- 
> 2.19.2
>
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d625b9..6ca286f6b37c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -557,6 +557,7 @@  dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-liteboard.dtb \
 	imx6ul-opos6uldev.dtb \
 	imx6ul-pico-hobbit.dtb \
+	imx6ul-phytec-phyboard-segin-full.dtb \
 	imx6ul-tx6ul-0010.dtb \
 	imx6ul-tx6ul-0011.dtb \
 	imx6ul-tx6ul-mainboard.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi b/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi
new file mode 100644
index 000000000000..ede24105044f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-phytec-pcl063.dtsi
@@ -0,0 +1,152 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx6ul.dtsi"
+
+/ {
+
+	model = "Phytec phyCORE i.MX6 UltraLite";
+	compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+
+	/*
+	 * Set the minimum memory size here and
+	 * let the bootloader set the real size.
+	 */
+	memory {
+		reg = <0x80000000 0x8000000>;
+	};
+
+	gpio_leds_som: somleds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioleds_som>;
+		compatible = "gpio-leds";
+		status = "okay";
+
+		som_green {
+			label = "phycore:green";
+			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			reg = <1>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <1>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 =<&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "catalyst,24c32", "atmel,24c32";
+		reg = <0x52>;
+	};
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x17059
+		>;
+	};
+
+	pinctrl_gpioleds_som: gpioledssomgrp {
+		fsl,pins = <MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x0b0b0>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x0b0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x0b0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0x0b0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x0b000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x0b0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x0b0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x0b0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x0b0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x0b0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x0b0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x0b0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x0b0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x0b0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0x0b0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x0b0b1
+		>;
+	};
+
+	pinctrl_i2c1: i2cgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL	0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+};
diff --git a/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi b/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi
new file mode 100644
index 000000000000..e7d115b0ff80
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-phytec-peb-eval-01.dtsi
@@ -0,0 +1,55 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	gpio_keys: gpio-keys {
+		compatible = "gpio-key";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "disabled";
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			gpio-key,wakeup;
+		};
+	};
+
+	user_leds: user_leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_user_leds>;
+		status = "disabled";
+
+		user_led_yellow {
+			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		user_led_red {
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio_keys: gpio_keysgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x79
+		>;
+	};
+
+	pinctrl_user_leds: user_ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0x79
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x79
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts
new file mode 100644
index 000000000000..4bee97a4e950
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin-full.dts
@@ -0,0 +1,103 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ul-phytec-pcl063.dtsi"
+#include "imx6ul-phytec-phyboard-segin.dtsi"
+#include "imx6ul-phytec-peb-eval-01.dtsi"
+
+/ {
+
+	model = "Phytec phyBOARD-Segin i.MX6 UltraLite Full Featured";
+	compatible = "phytec,imx6ul-pbacd10", "phytec,imx6ul-pcl063",
+		     "fsl,imx6ul";
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&fec2 {
+	status = "okay";
+};
+
+&i2c_rtc {
+	status = "okay";
+};
+
+&reg_can1_en {
+	status = "okay";
+};
+
+&reg_sound_1v8 {
+	status = "okay";
+};
+
+&reg_sound_3v3 {
+	status = "okay";
+};
+
+&sai2 {
+	status = "okay";
+};
+
+&sound {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbotg1 {
+	status = "okay";
+};
+
+&usbotg2 {
+	status = "okay";
+};
+
+&usdhc1 {
+	status = "okay";
+};
+
+
+&ecspi3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+
+	fsl,spi-num-chipselects=<0>;
+	cs-gpios = <0>;
+
+	spidev@0 {
+		compatible = "spidev";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+
+};
+
+
+&iomuxc {
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b0
+			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b0
+			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b0
+			MX6UL_PAD_UART2_TX_DATA__ECSPI3_SS0 0x10b0
+		>;
+	};
+};
+
diff --git a/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi
new file mode 100644
index 000000000000..3e59f49ce5cc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-phytec-phyboard-segin.dtsi
@@ -0,0 +1,341 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/ {
+
+	model = "Phytec phyBOARD-Segin i.MX6 UltraLite";
+	compatible = "phytec,imx6ul-pbacd-10", "phytec,imx6ul-pcl063",
+		     "fsl,imx6ul";
+
+	aliases {
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_sound_1v8: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "i2s-audio-1v8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			status = "disabled";
+		};
+
+		reg_sound_3v3: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "i2s-audio-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			status = "disabled";
+		};
+
+		reg_can1_en: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&princtrl_flexcan1_en>;
+			regulator-name = "Can";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			status = "disabled";
+		};
+
+		reg_adc1_vref_3v3: regulator@5 {
+			compatible = "regulator-fixed";
+			regulator-name = "vref-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "phyBOARD-Segin-TLV320AIC3007";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,widgets =
+			"Line", "Line In",
+			"Line", "Line Out",
+			"Speaker", "Speaker";
+		simple-audio-card,routing =
+			"Line Out", "LLOUT",
+			"Line Out", "RLOUT",
+			"Speaker", "SPOP",
+			"Speaker", "SPOM",
+			"LINE1L", "Line In",
+			"LINE1R", "Line In";
+		status = "disabled";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			sound-dai = <&codec>;
+			clocks = <&clks IMX6UL_CLK_SAI2>;
+		};
+	};
+
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_en>;
+	status = "disabled";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <786432000>;
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "disabled";
+};
+
+&i2c1 {
+	codec: tlv320@18 {
+		compatible = "ti,tlv320aic3007";
+		#sound-dai-cells = <0>;
+		reg = <0x18>;
+
+		AVDD-supply = <&reg_sound_3v3>;
+		IOVDD-supply = <&reg_sound_3v3>;
+		DRVDD-supply = <&reg_sound_3v3>;
+		DVDD-supply = <&reg_sound_1v8>;
+		status = "disabled";
+	};
+
+	stmpe: stmpe@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio5>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stmpe>;
+		status = "disabled";
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+			touchscreen-inverted-x = <1>;
+			touchscreen-inverted-y = <1>;
+		};
+	};
+
+	i2c_rtc: rtc@68 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		status = "disabled";
+	};
+};
+
+&mdio {
+	ethphy1: ethernet-phy@2 {
+		reg = <2>;
+		micrel,led-mode = <1>;
+		clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+		clock-names = "rmii-ref";
+	};
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "disabled";
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
+			<&clks IMX6UL_CLK_SAI2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <0>, <19200000>;
+	fsl,sai-mclk-direction-output;
+	status = "disabled";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	status = "disabled";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "disabled";
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc1>;
+	vref-supply = <&reg_adc1_vref_3v3>;
+	status = "disabled";
+	/*
+	 * driver can not separate a specific channel so we request 4 channels
+	 * here - we need only the fourth channel
+	 */
+	num-channels = <4>;
+};
+
+&iomuxc {
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1 {
+		fsl,pins = <
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x0b0b0
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x0b0b0
+		>;
+	};
+
+	princtrl_flexcan1_en: flexcan1engrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x17059
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__PWM3_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17059
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x11088
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x11088
+			MX6UL_PAD_JTAG_TMS__SAI2_MCLK		0x17088
+		>;
+	};
+
+	pinctrl_stmpe: stmpegrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
+			MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS	0x1b0b1
+			MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_adc1: adc1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+		>;
+	};
+};