[v1,1/3] thermal: rockchip: add pinctrl control
diff mbox series

Message ID 1554100985-11385-2-git-send-email-zhangqing@rock-chips.com
State Superseded
Delegated to: Eduardo Valentin
Headers show
Series
  • thermal: rockchip: fix up thermal driver
Related show

Commit Message

elaine.zhang April 1, 2019, 6:43 a.m. UTC
Based on the TSADC Tshut mode to select pinctrl,
instead of setting pinctrl based on architecture
(Not depends on pinctrl setting by "init" or "default").
And it requires setting the tshut polarity before select pinctrl.

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
---
 drivers/thermal/rockchip_thermal.c | 61 +++++++++++++++++++++++++++++++-------
 1 file changed, 50 insertions(+), 11 deletions(-)

Comments

Daniel Lezcano April 4, 2019, 3:03 a.m. UTC | #1
On 01/04/2019 08:43, Elaine Zhang wrote:
> Based on the TSADC Tshut mode to select pinctrl,
> instead of setting pinctrl based on architecture
> (Not depends on pinctrl setting by "init" or "default").
> And it requires setting the tshut polarity before select pinctrl.

I'm not sure to fully read the description. Can you rephrase/elaborate
the changelog?

> Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
> ---
>  drivers/thermal/rockchip_thermal.c | 61 +++++++++++++++++++++++++++++++-------
>  1 file changed, 50 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/thermal/rockchip_thermal.c b/drivers/thermal/rockchip_thermal.c
> index 9c7643d62ed7..faa6c7792155 100644
> --- a/drivers/thermal/rockchip_thermal.c
> +++ b/drivers/thermal/rockchip_thermal.c
> @@ -34,7 +34,7 @@
>   */
>  enum tshut_mode {
>  	TSHUT_MODE_CRU = 0,
> -	TSHUT_MODE_GPIO,
> +	TSHUT_MODE_OTP,

Why do you change the enum name? The impact on the patch is much higher,
no ?

>  };
>  
>  /**
> @@ -172,6 +172,9 @@ struct rockchip_thermal_data {
>  	int tshut_temp;
>  	enum tshut_mode tshut_mode;
>  	enum tshut_polarity tshut_polarity;
> +	struct pinctrl *pinctrl;
> +	struct pinctrl_state *gpio_state;
> +	struct pinctrl_state *otp_state;
>  };
>  
>  /**
> @@ -807,7 +810,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>  	u32 val;
>  
>  	val = readl_relaxed(regs + TSADCV2_INT_EN);
> -	if (mode == TSHUT_MODE_GPIO) {
> +	if (mode == TSHUT_MODE_OTP) {
>  		val &= ~TSADCV2_SHUT_2CRU_SRC_EN(chn);
>  		val |= TSADCV2_SHUT_2GPIO_SRC_EN(chn);
>  	} else {
> @@ -822,7 +825,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>  	.chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
>  	.chn_num = 1, /* one channel for tsadc */
>  
> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>  	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>  	.tshut_temp = 95000,
>  
> @@ -846,7 +849,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>  	.chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
>  	.chn_num = 1, /* one channel for tsadc */
>  
> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>  	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>  	.tshut_temp = 95000,
>  
> @@ -871,7 +874,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>  	.chn_id[SENSOR_GPU] = 2, /* gpu sensor is channel 2 */
>  	.chn_num = 2, /* two channels for tsadc */
>  
> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>  	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>  	.tshut_temp = 95000,
>  
> @@ -919,7 +922,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>  	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
>  	.chn_num = 2, /* two channels for tsadc */
>  
> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>  	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>  	.tshut_temp = 95000,
>  
> @@ -944,7 +947,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>  	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
>  	.chn_num = 2, /* two channels for tsadc */
>  
> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>  	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>  	.tshut_temp = 95000,
>  
> @@ -969,7 +972,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>  	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
>  	.chn_num = 2, /* two channels for tsadc */
>  
> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>  	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>  	.tshut_temp = 95000,
>  
> @@ -1080,6 +1083,20 @@ static int rockchip_thermal_get_temp(void *_sensor, int *out_temp)
>  	.set_trips = rockchip_thermal_set_trips,
>  };
>  
> +static void thermal_pinctrl_select_otp(struct rockchip_thermal_data *thermal)
> +{
> +	if (!IS_ERR(thermal->pinctrl) && !IS_ERR_OR_NULL(thermal->otp_state))
> +		pinctrl_select_state(thermal->pinctrl,
> +				     thermal->otp_state);
> +}
> +
> +static void thermal_pinctrl_select_gpio(struct rockchip_thermal_data *thermal)
> +{
> +	if (!IS_ERR(thermal->pinctrl) && !IS_ERR_OR_NULL(thermal->gpio_state))
> +		pinctrl_select_state(thermal->pinctrl,
> +				     thermal->gpio_state);
> +}

You should not have to create a couple of specific functions just to
check the pinctrl pointers are set. The caller should do that.

>  static int rockchip_configure_from_dt(struct device *dev,
>  				      struct device_node *np,
>  				      struct rockchip_thermal_data *thermal)
> @@ -1103,7 +1120,7 @@ static int rockchip_configure_from_dt(struct device *dev,
>  	if (of_property_read_u32(np, "rockchip,hw-tshut-mode", &tshut_mode)) {
>  		dev_warn(dev,
>  			 "Missing tshut mode property, using default (%s)\n",
> -			 thermal->chip->tshut_mode == TSHUT_MODE_GPIO ?
> +			 thermal->chip->tshut_mode == TSHUT_MODE_OTP ?
>  				"gpio" : "cru");
>  		thermal->tshut_mode = thermal->chip->tshut_mode;
>  	} else {
> @@ -1242,6 +1259,8 @@ static int rockchip_thermal_probe(struct platform_device *pdev)
>  		return error;
>  	}
>  
> +	thermal->chip->control(thermal->regs, false);
> +
>  	error = clk_prepare_enable(thermal->clk);
>  	if (error) {
>  		dev_err(&pdev->dev, "failed to enable converter clock: %d\n",
> @@ -1267,6 +1286,24 @@ static int rockchip_thermal_probe(struct platform_device *pdev)
>  	thermal->chip->initialize(thermal->grf, thermal->regs,
>  				  thermal->tshut_polarity);
>  
> +	if (thermal->tshut_mode == TSHUT_MODE_OTP) {
> +		thermal->pinctrl = devm_pinctrl_get(&pdev->dev);
> +		if (IS_ERR(thermal->pinctrl))
> +			dev_err(&pdev->dev, "failed to find thermal pinctrl\n");
> +
> +		thermal->gpio_state = pinctrl_lookup_state(thermal->pinctrl,
> +							   "gpio");
> +		if (IS_ERR_OR_NULL(thermal->gpio_state))
> +			dev_err(&pdev->dev, "failed to find thermal gpio state\n");
> +
> +		thermal->otp_state = pinctrl_lookup_state(thermal->pinctrl,
> +							  "otpout");
> +		if (IS_ERR_OR_NULL(thermal->otp_state))
> +			dev_err(&pdev->dev, "failed to find thermal otpout state\n");

What is the meaning for the rest of the code if the lookup fails for any
of those ?

> +		thermal_pinctrl_select_otp(thermal);
> +	}
> +
>  	for (i = 0; i < thermal->chip->chn_num; i++) {
>  		error = rockchip_thermal_register_sensor(pdev, thermal,
>  						&thermal->sensors[i],
> @@ -1338,7 +1375,8 @@ static int __maybe_unused rockchip_thermal_suspend(struct device *dev)
>  	clk_disable(thermal->pclk);
>  	clk_disable(thermal->clk);
>  
> -	pinctrl_pm_select_sleep_state(dev);
> +	if (thermal->tshut_mode == TSHUT_MODE_OTP)
> +		thermal_pinctrl_select_gpio(thermal);
>  
>  	return 0;
>  }
> @@ -1383,7 +1421,8 @@ static int __maybe_unused rockchip_thermal_resume(struct device *dev)
>  	for (i = 0; i < thermal->chip->chn_num; i++)
>  		rockchip_thermal_toggle_sensor(&thermal->sensors[i], true);
>  
> -	pinctrl_pm_select_default_state(dev);
> +	if (thermal->tshut_mode == TSHUT_MODE_OTP)
> +		thermal_pinctrl_select_otp(thermal);
>  
>  	return 0;
>  }
>
elaine.zhang April 11, 2019, 7:46 a.m. UTC | #2
hi,

在 2019/4/4 上午11:03, Daniel Lezcano 写道:
> On 01/04/2019 08:43, Elaine Zhang wrote:
>> Based on the TSADC Tshut mode to select pinctrl,
>> instead of setting pinctrl based on architecture
>> (Not depends on pinctrl setting by "init" or "default").
>> And it requires setting the tshut polarity before select pinctrl.
> I'm not sure to fully read the description. Can you rephrase/elaborate
> the changelog?
Example:
         tsadc: tsadc@ff250000 {
                     compatible = "rockchip,rk3328-tsadc";
                     .....
                 pinctrl-names = "init", "default", "sleep";
                     pinctrl-0 = <&otp_gpio>;
                     pinctrl-1 = <&otp_out>;
                     pinctrl-2 = <&otp_gpio>;
                     status = "disabled";
                 .....
             };
         &tsadc {
                 rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
                 status = "okay";
         };
     Application on the product, hope tsadc overtemperature reset cru to 
restart.
     But when pinctrl is initialized, it will setting pinctrl by "init" 
and "default".
     So the pinctrl will set iomux to "otp_out", which may be make 
system crash.
     tsadc gpio iomux:
     "otp_gpio" : just normal gpio, keep default level.
     "otp_out" : tsadc shut down io, when overtemperature,this io may be 
trigger high
     level or low level(depend on the tsadc polarity).

     After correction:
     if rockchip,hw-tshut-mode = <0>; (tsadc overtemperature reset cru 
to restart)
     select pinctrl to otp_gpio
     if rockchip,hw-tshut-mode = <1>;(tsadc overtemperature IO triggers 
output at high or low levels)
     select pinctrl to otp_out.
     Actively select iomux based on rockchip,hw-tshut-mode,
     rather than relying on the pinctrl framework to select iomux.
>> Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
>> ---
>>   drivers/thermal/rockchip_thermal.c | 61 +++++++++++++++++++++++++++++++-------
>>   1 file changed, 50 insertions(+), 11 deletions(-)
>>
>> diff --git a/drivers/thermal/rockchip_thermal.c b/drivers/thermal/rockchip_thermal.c
>> index 9c7643d62ed7..faa6c7792155 100644
>> --- a/drivers/thermal/rockchip_thermal.c
>> +++ b/drivers/thermal/rockchip_thermal.c
>> @@ -34,7 +34,7 @@
>>    */
>>   enum tshut_mode {
>>   	TSHUT_MODE_CRU = 0,
>> -	TSHUT_MODE_GPIO,
>> +	TSHUT_MODE_OTP,
> Why do you change the enum name? The impact on the patch is much higher,
> no ?

I just want to make it a little bit more intuitive to understand the 
definition of mode.

TSHUT_MODE_CRU: pinctrl select iomux to otp_gpio,the io is normal io.
TSHUT_MODE_OTP: pinctrl select iomux to otp_out, the io is tsadc shut io.

>
>>   };
>>   
>>   /**
>> @@ -172,6 +172,9 @@ struct rockchip_thermal_data {
>>   	int tshut_temp;
>>   	enum tshut_mode tshut_mode;
>>   	enum tshut_polarity tshut_polarity;
>> +	struct pinctrl *pinctrl;
>> +	struct pinctrl_state *gpio_state;
>> +	struct pinctrl_state *otp_state;
>>   };
>>   
>>   /**
>> @@ -807,7 +810,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>>   	u32 val;
>>   
>>   	val = readl_relaxed(regs + TSADCV2_INT_EN);
>> -	if (mode == TSHUT_MODE_GPIO) {
>> +	if (mode == TSHUT_MODE_OTP) {
>>   		val &= ~TSADCV2_SHUT_2CRU_SRC_EN(chn);
>>   		val |= TSADCV2_SHUT_2GPIO_SRC_EN(chn);
>>   	} else {
>> @@ -822,7 +825,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>>   	.chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
>>   	.chn_num = 1, /* one channel for tsadc */
>>   
>> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
>> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>>   	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>>   	.tshut_temp = 95000,
>>   
>> @@ -846,7 +849,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>>   	.chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
>>   	.chn_num = 1, /* one channel for tsadc */
>>   
>> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
>> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>>   	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>>   	.tshut_temp = 95000,
>>   
>> @@ -871,7 +874,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>>   	.chn_id[SENSOR_GPU] = 2, /* gpu sensor is channel 2 */
>>   	.chn_num = 2, /* two channels for tsadc */
>>   
>> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
>> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>>   	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>>   	.tshut_temp = 95000,
>>   
>> @@ -919,7 +922,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>>   	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
>>   	.chn_num = 2, /* two channels for tsadc */
>>   
>> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
>> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>>   	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>>   	.tshut_temp = 95000,
>>   
>> @@ -944,7 +947,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>>   	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
>>   	.chn_num = 2, /* two channels for tsadc */
>>   
>> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
>> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>>   	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>>   	.tshut_temp = 95000,
>>   
>> @@ -969,7 +972,7 @@ static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
>>   	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
>>   	.chn_num = 2, /* two channels for tsadc */
>>   
>> -	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
>> +	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
>>   	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
>>   	.tshut_temp = 95000,
>>   
>> @@ -1080,6 +1083,20 @@ static int rockchip_thermal_get_temp(void *_sensor, int *out_temp)
>>   	.set_trips = rockchip_thermal_set_trips,
>>   };
>>   
>> +static void thermal_pinctrl_select_otp(struct rockchip_thermal_data *thermal)
>> +{
>> +	if (!IS_ERR(thermal->pinctrl) && !IS_ERR_OR_NULL(thermal->otp_state))
>> +		pinctrl_select_state(thermal->pinctrl,
>> +				     thermal->otp_state);
>> +}
>> +
>> +static void thermal_pinctrl_select_gpio(struct rockchip_thermal_data *thermal)
>> +{
>> +	if (!IS_ERR(thermal->pinctrl) && !IS_ERR_OR_NULL(thermal->gpio_state))
>> +		pinctrl_select_state(thermal->pinctrl,
>> +				     thermal->gpio_state);
>> +}
> You should not have to create a couple of specific functions just to
> check the pinctrl pointers are set. The caller should do that.
Because there are several places where the call is made,create a couple 
of specific functions reduce a lot of duplicated code.
>
>>   static int rockchip_configure_from_dt(struct device *dev,
>>   				      struct device_node *np,
>>   				      struct rockchip_thermal_data *thermal)
>> @@ -1103,7 +1120,7 @@ static int rockchip_configure_from_dt(struct device *dev,
>>   	if (of_property_read_u32(np, "rockchip,hw-tshut-mode", &tshut_mode)) {
>>   		dev_warn(dev,
>>   			 "Missing tshut mode property, using default (%s)\n",
>> -			 thermal->chip->tshut_mode == TSHUT_MODE_GPIO ?
>> +			 thermal->chip->tshut_mode == TSHUT_MODE_OTP ?
>>   				"gpio" : "cru");
>>   		thermal->tshut_mode = thermal->chip->tshut_mode;
>>   	} else {
>> @@ -1242,6 +1259,8 @@ static int rockchip_thermal_probe(struct platform_device *pdev)
>>   		return error;
>>   	}
>>   
>> +	thermal->chip->control(thermal->regs, false);
>> +
>>   	error = clk_prepare_enable(thermal->clk);
>>   	if (error) {
>>   		dev_err(&pdev->dev, "failed to enable converter clock: %d\n",
>> @@ -1267,6 +1286,24 @@ static int rockchip_thermal_probe(struct platform_device *pdev)
>>   	thermal->chip->initialize(thermal->grf, thermal->regs,
>>   				  thermal->tshut_polarity);
>>   
>> +	if (thermal->tshut_mode == TSHUT_MODE_OTP) {
>> +		thermal->pinctrl = devm_pinctrl_get(&pdev->dev);
>> +		if (IS_ERR(thermal->pinctrl))
>> +			dev_err(&pdev->dev, "failed to find thermal pinctrl\n");
>> +
>> +		thermal->gpio_state = pinctrl_lookup_state(thermal->pinctrl,
>> +							   "gpio");
>> +		if (IS_ERR_OR_NULL(thermal->gpio_state))
>> +			dev_err(&pdev->dev, "failed to find thermal gpio state\n");
>> +
>> +		thermal->otp_state = pinctrl_lookup_state(thermal->pinctrl,
>> +							  "otpout");
>> +		if (IS_ERR_OR_NULL(thermal->otp_state))
>> +			dev_err(&pdev->dev, "failed to find thermal otpout state\n");
> What is the meaning for the rest of the code if the lookup fails for any
> of those ?
If the lookup fails for any of those, The pinctrl is no longer set and 
remains in its default state(otp_gpio normal io).
>
>> +		thermal_pinctrl_select_otp(thermal);
>> +	}
>> +
>>   	for (i = 0; i < thermal->chip->chn_num; i++) {
>>   		error = rockchip_thermal_register_sensor(pdev, thermal,
>>   						&thermal->sensors[i],
>> @@ -1338,7 +1375,8 @@ static int __maybe_unused rockchip_thermal_suspend(struct device *dev)
>>   	clk_disable(thermal->pclk);
>>   	clk_disable(thermal->clk);
>>   
>> -	pinctrl_pm_select_sleep_state(dev);
>> +	if (thermal->tshut_mode == TSHUT_MODE_OTP)
>> +		thermal_pinctrl_select_gpio(thermal);
>>   
>>   	return 0;
>>   }
>> @@ -1383,7 +1421,8 @@ static int __maybe_unused rockchip_thermal_resume(struct device *dev)
>>   	for (i = 0; i < thermal->chip->chn_num; i++)
>>   		rockchip_thermal_toggle_sensor(&thermal->sensors[i], true);
>>   
>> -	pinctrl_pm_select_default_state(dev);
>> +	if (thermal->tshut_mode == TSHUT_MODE_OTP)
>> +		thermal_pinctrl_select_otp(thermal);
>>   
>>   	return 0;
>>   }
>>
>
Daniel Lezcano April 16, 2019, 10:12 a.m. UTC | #3
Hi Elaine,

On 11/04/2019 09:46, elaine.zhang wrote:
> hi,
> 
> 在 2019/4/4 上午11:03, Daniel Lezcano 写道:
>> On 01/04/2019 08:43, Elaine Zhang wrote:
>>> Based on the TSADC Tshut mode to select pinctrl,
>>> instead of setting pinctrl based on architecture
>>> (Not depends on pinctrl setting by "init" or "default").
>>> And it requires setting the tshut polarity before select pinctrl.
>> I'm not sure to fully read the description. Can you rephrase/elaborate
>> the changelog?
> Example:
>         tsadc: tsadc@ff250000 {
>                     compatible = "rockchip,rk3328-tsadc";
>                     .....
>                 pinctrl-names = "init", "default", "sleep";
>                     pinctrl-0 = <&otp_gpio>;
>                     pinctrl-1 = <&otp_out>;
>                     pinctrl-2 = <&otp_gpio>;
>                     status = "disabled";
>                 .....
>             };
>         &tsadc {
>                 rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
>                 status = "okay";
>         };
>     Application on the product, hope tsadc overtemperature reset cru to
> restart.
>     But when pinctrl is initialized, it will setting pinctrl by "init"
> and "default".
>     So the pinctrl will set iomux to "otp_out", which may be make system
> crash.

why?

>     tsadc gpio iomux:
>     "otp_gpio" : just normal gpio, keep default level.
>     "otp_out" : tsadc shut down io, when overtemperature,this io may be
> trigger high
>     level or low level(depend on the tsadc polarity).
> 
>     After correction:
>     if rockchip,hw-tshut-mode = <0>; (tsadc overtemperature reset cru to
> restart)
>     select pinctrl to otp_gpio
>     if rockchip,hw-tshut-mode = <1>;(tsadc overtemperature IO triggers
> output at high or low levels)
>     select pinctrl to otp_out.
>     Actively select iomux based on rockchip,hw-tshut-mode,
>     rather than relying on the pinctrl framework to select iomux.

Let me rephrase it and tell me if I understood correctly:

"When the temperature sensor mode is set to 0, it will automatically
reset the board via the Clock-Reset-Unit (CRU) if the over temperature
threshold is reached. However, when the pinctrl initializes, it does a
transition to "otp_out" which may lead the SoC to crash (why?)

Explicitly use the pinctrl to set/unset the right mode instead of
relying on the pinctrl init mode"

So this patch is a fix and it must contain the Fixes: ... tag.


>>> Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
>>> ---
>>>   drivers/thermal/rockchip_thermal.c | 61
>>> +++++++++++++++++++++++++++++++-------
>>>   1 file changed, 50 insertions(+), 11 deletions(-)
>>>
>>> diff --git a/drivers/thermal/rockchip_thermal.c
>>> b/drivers/thermal/rockchip_thermal.c
>>> index 9c7643d62ed7..faa6c7792155 100644
>>> --- a/drivers/thermal/rockchip_thermal.c
>>> +++ b/drivers/thermal/rockchip_thermal.c
>>> @@ -34,7 +34,7 @@
>>>    */
>>>   enum tshut_mode {
>>>       TSHUT_MODE_CRU = 0,
>>> -    TSHUT_MODE_GPIO,
>>> +    TSHUT_MODE_OTP,
>> Why do you change the enum name? The impact on the patch is much higher,
>> no ?
> 
> I just want to make it a little bit more intuitive to understand the
> definition of mode.
> 
> TSHUT_MODE_CRU: pinctrl select iomux to otp_gpio,the io is normal io.
> TSHUT_MODE_OTP: pinctrl select iomux to otp_out, the io is tsadc shut io.

I understand, but at the end the changes for this patch are counter
intuitive, so it is preferable to keep it as is so we can review the
important part.

[ ... ]

>>>   +static void thermal_pinctrl_select_otp(struct
>>> rockchip_thermal_data *thermal)
>>> +{
>>> +    if (!IS_ERR(thermal->pinctrl) &&
>>> !IS_ERR_OR_NULL(thermal->otp_state))
>>> +        pinctrl_select_state(thermal->pinctrl,
>>> +                     thermal->otp_state);
>>> +}
>>> +
>>> +static void thermal_pinctrl_select_gpio(struct rockchip_thermal_data
>>> *thermal)
>>> +{
>>> +    if (!IS_ERR(thermal->pinctrl) &&
>>> !IS_ERR_OR_NULL(thermal->gpio_state))
>>> +        pinctrl_select_state(thermal->pinctrl,
>>> +                     thermal->gpio_state);
>>> +}
>> You should not have to create a couple of specific functions just to
>> check the pinctrl pointers are set. The caller should do that.
> Because there are several places where the call is made,create a couple
> of specific functions reduce a lot of duplicated code.

No, that does not reduce a lot of duplicated code, it hides the fact
there is no control from the caller. See the comments below.

[ ... ]

>>>   static int rockchip_configure_from_dt(struct device *dev,
>>>                         struct device_node *np,
>>>                         struct rockchip_thermal_data *thermal)
>>> @@ -1103,7 +1120,7 @@ static int rockchip_configure_from_dt(struct
>>> device *dev,
>>>       if (of_property_read_u32(np, "rockchip,hw-tshut-mode",
>>> &tshut_mode)) {
>>>           dev_warn(dev,
>>>                "Missing tshut mode property, using default (%s)\n",
>>> -             thermal->chip->tshut_mode == TSHUT_MODE_GPIO ?
>>> +             thermal->chip->tshut_mode == TSHUT_MODE_OTP ?
>>>                   "gpio" : "cru");
>>>           thermal->tshut_mode = thermal->chip->tshut_mode;
>>>       } else {
>>> @@ -1242,6 +1259,8 @@ static int rockchip_thermal_probe(struct
>>> platform_device *pdev)
>>>           return error;
>>>       }
>>>   +    thermal->chip->control(thermal->regs, false);
>>> +
>>>       error = clk_prepare_enable(thermal->clk);
>>>       if (error) {
>>>           dev_err(&pdev->dev, "failed to enable converter clock: %d\n",
>>> @@ -1267,6 +1286,24 @@ static int rockchip_thermal_probe(struct
>>> platform_device *pdev)
>>>       thermal->chip->initialize(thermal->grf, thermal->regs,
>>>                     thermal->tshut_polarity);
>>>   +    if (thermal->tshut_mode == TSHUT_MODE_OTP) {
>>> +        thermal->pinctrl = devm_pinctrl_get(&pdev->dev);
>>> +        if (IS_ERR(thermal->pinctrl))
>>> +            dev_err(&pdev->dev, "failed to find thermal pinctrl\n");
>>> +
>>> +        thermal->gpio_state = pinctrl_lookup_state(thermal->pinctrl,
>>> +                               "gpio");

panic if devm_pinctrl_get fails.

>>> +        if (IS_ERR_OR_NULL(thermal->gpio_state))
>>> +            dev_err(&pdev->dev, "failed to find thermal gpio state\n");
>>> +
>>> +        thermal->otp_state = pinctrl_lookup_state(thermal->pinctrl,
>>> +                              "otpout");
>>> +        if (IS_ERR_OR_NULL(thermal->otp_state))
>>> +            dev_err(&pdev->dev, "failed to find thermal otpout
>>> state\n");
>> What is the meaning for the rest of the code if the lookup fails for any
>> of those ?
> If the lookup fails for any of those, The pinctrl is no longer set and
> remains in its default state(otp_gpio normal io).
>>
>>> +        thermal_pinctrl_select_otp(thermal);
>>> +    }
>>> +

It is pointless to have a otp_state and a gpio_state field. Just use one
as the configuration tells you which lookup to do.

In case of error, just bail out. It is pointless to continue with a
broken configuration.

	thermal->pinctrl = devm_pinctrl_get(&pdev->dev);
	if (IS_ERR(thermal->pinctrl)) {
		dev_err(&pdev->dev, "....");
		return PTR_ERR(thermal->pinctrl);
	}

	thermal->pinctrl_state =
		pinctrl_lookup_state(thermal->pinctrl,
			thermal->tshut_mode == TSHUT_MODE_OTP ?
			"otp" : "gpio");

	if (IS_ERR_OR_NULL(thermal->pinctrl_state)) {
		dev_err(&pdev->dev, "....");
		return -EINVAL;
	}


No need to use the thermal_pinctrl_select_otp/gpio wrappers, just
replace them with:

pinctrl_select_state(thermal->pinctrl, thermal->pinctrl_state);

and use it unconditionally.


>>>       for (i = 0; i < thermal->chip->chn_num; i++) {
>>>           error = rockchip_thermal_register_sensor(pdev, thermal,
>>>                           &thermal->sensors[i],
>>> @@ -1338,7 +1375,8 @@ static int __maybe_unused
>>> rockchip_thermal_suspend(struct device *dev)
>>>       clk_disable(thermal->pclk);
>>>       clk_disable(thermal->clk);
>>>   -    pinctrl_pm_select_sleep_state(dev);
>>> +    if (thermal->tshut_mode == TSHUT_MODE_OTP)
>>> +        thermal_pinctrl_select_gpio(thermal);
>>>         return 0;
>>>   }
>>> @@ -1383,7 +1421,8 @@ static int __maybe_unused
>>> rockchip_thermal_resume(struct device *dev)
>>>       for (i = 0; i < thermal->chip->chn_num; i++)
>>>           rockchip_thermal_toggle_sensor(&thermal->sensors[i], true);
>>>   -    pinctrl_pm_select_default_state(dev);
>>> +    if (thermal->tshut_mode == TSHUT_MODE_OTP)
>>> +        thermal_pinctrl_select_otp(thermal);
>>>         return 0;
>>>   }
>>>
>>
> 
>
elaine.zhang April 17, 2019, 3:22 a.m. UTC | #4
hi,

在 2019/4/16 下午6:12, Daniel Lezcano 写道:
> Hi Elaine,
>
> On 11/04/2019 09:46, elaine.zhang wrote:
>> hi,
>>
>> 在 2019/4/4 上午11:03, Daniel Lezcano 写道:
>>> On 01/04/2019 08:43, Elaine Zhang wrote:
>>>> Based on the TSADC Tshut mode to select pinctrl,
>>>> instead of setting pinctrl based on architecture
>>>> (Not depends on pinctrl setting by "init" or "default").
>>>> And it requires setting the tshut polarity before select pinctrl.
>>> I'm not sure to fully read the description. Can you rephrase/elaborate
>>> the changelog?
>> Example:
>>          tsadc: tsadc@ff250000 {
>>                      compatible = "rockchip,rk3328-tsadc";
>>                      .....
>>                  pinctrl-names = "init", "default", "sleep";
>>                      pinctrl-0 = <&otp_gpio>;
>>                      pinctrl-1 = <&otp_out>;
>>                      pinctrl-2 = <&otp_gpio>;
>>                      status = "disabled";
>>                  .....
>>              };
>>          &tsadc {
>>                  rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
>>                  status = "okay";
>>          };
>>      Application on the product, hope tsadc overtemperature reset cru to
>> restart.
>>      But when pinctrl is initialized, it will setting pinctrl by "init"
>> and "default".
>>      So the pinctrl will set iomux to "otp_out", which may be make system
>> crash.
> why?
This "otp_out" IO may be connected to the RESET circuit on the hardware. 
If the IO is in the wrong state, it will trigger RESET (similar to the 
effect of pressing the RESET button), which will cause the system to 
restart all the time.
>
>>      tsadc gpio iomux:
>>      "otp_gpio" : just normal gpio, keep default level.
>>      "otp_out" : tsadc shut down io, when overtemperature,this io may be
>> trigger high
>>      level or low level(depend on the tsadc polarity).
>>
>>      After correction:
>>      if rockchip,hw-tshut-mode = <0>; (tsadc overtemperature reset cru to
>> restart)
>>      select pinctrl to otp_gpio
>>      if rockchip,hw-tshut-mode = <1>;(tsadc overtemperature IO triggers
>> output at high or low levels)
>>      select pinctrl to otp_out.
>>      Actively select iomux based on rockchip,hw-tshut-mode,
>>      rather than relying on the pinctrl framework to select iomux.
> Let me rephrase it and tell me if I understood correctly:
>
> "When the temperature sensor mode is set to 0, it will automatically
> reset the board via the Clock-Reset-Unit (CRU) if the over temperature
> threshold is reached. However, when the pinctrl initializes, it does a
> transition to "otp_out" which may lead the SoC to crash (why?)
>
> Explicitly use the pinctrl to set/unset the right mode instead of
> relying on the pinctrl init mode"
This explanation is correct.
>
> So this patch is a fix and it must contain the Fixes: ... tag.
OK, I'll fix that in the v2.
>
>
>>>> Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
>>>> ---
>>>>    drivers/thermal/rockchip_thermal.c | 61
>>>> +++++++++++++++++++++++++++++++-------
>>>>    1 file changed, 50 insertions(+), 11 deletions(-)
>>>>
>>>> diff --git a/drivers/thermal/rockchip_thermal.c
>>>> b/drivers/thermal/rockchip_thermal.c
>>>> index 9c7643d62ed7..faa6c7792155 100644
>>>> --- a/drivers/thermal/rockchip_thermal.c
>>>> +++ b/drivers/thermal/rockchip_thermal.c
>>>> @@ -34,7 +34,7 @@
>>>>     */
>>>>    enum tshut_mode {
>>>>        TSHUT_MODE_CRU = 0,
>>>> -    TSHUT_MODE_GPIO,
>>>> +    TSHUT_MODE_OTP,
>>> Why do you change the enum name? The impact on the patch is much higher,
>>> no ?
>> I just want to make it a little bit more intuitive to understand the
>> definition of mode.
>>
>> TSHUT_MODE_CRU: pinctrl select iomux to otp_gpio,the io is normal io.
>> TSHUT_MODE_OTP: pinctrl select iomux to otp_out, the io is tsadc shut io.
> I understand, but at the end the changes for this patch are counter
> intuitive, so it is preferable to keep it as is so we can review the
> important part.
>
> [ ... ]
OK, keep the enum name. I'll fix it in the V2.
>
>>>>    +static void thermal_pinctrl_select_otp(struct
>>>> rockchip_thermal_data *thermal)
>>>> +{
>>>> +    if (!IS_ERR(thermal->pinctrl) &&
>>>> !IS_ERR_OR_NULL(thermal->otp_state))
>>>> +        pinctrl_select_state(thermal->pinctrl,
>>>> +                     thermal->otp_state);
>>>> +}
>>>> +
>>>> +static void thermal_pinctrl_select_gpio(struct rockchip_thermal_data
>>>> *thermal)
>>>> +{
>>>> +    if (!IS_ERR(thermal->pinctrl) &&
>>>> !IS_ERR_OR_NULL(thermal->gpio_state))
>>>> +        pinctrl_select_state(thermal->pinctrl,
>>>> +                     thermal->gpio_state);
>>>> +}
>>> You should not have to create a couple of specific functions just to
>>> check the pinctrl pointers are set. The caller should do that.
>> Because there are several places where the call is made,create a couple
>> of specific functions reduce a lot of duplicated code.
> No, that does not reduce a lot of duplicated code, it hides the fact
> there is no control from the caller. See the comments below.
>
> [ ... ]
OK, I'll fix it in the V2.
>
>>>>    static int rockchip_configure_from_dt(struct device *dev,
>>>>                          struct device_node *np,
>>>>                          struct rockchip_thermal_data *thermal)
>>>> @@ -1103,7 +1120,7 @@ static int rockchip_configure_from_dt(struct
>>>> device *dev,
>>>>        if (of_property_read_u32(np, "rockchip,hw-tshut-mode",
>>>> &tshut_mode)) {
>>>>            dev_warn(dev,
>>>>                 "Missing tshut mode property, using default (%s)\n",
>>>> -             thermal->chip->tshut_mode == TSHUT_MODE_GPIO ?
>>>> +             thermal->chip->tshut_mode == TSHUT_MODE_OTP ?
>>>>                    "gpio" : "cru");
>>>>            thermal->tshut_mode = thermal->chip->tshut_mode;
>>>>        } else {
>>>> @@ -1242,6 +1259,8 @@ static int rockchip_thermal_probe(struct
>>>> platform_device *pdev)
>>>>            return error;
>>>>        }
>>>>    +    thermal->chip->control(thermal->regs, false);
>>>> +
>>>>        error = clk_prepare_enable(thermal->clk);
>>>>        if (error) {
>>>>            dev_err(&pdev->dev, "failed to enable converter clock: %d\n",
>>>> @@ -1267,6 +1286,24 @@ static int rockchip_thermal_probe(struct
>>>> platform_device *pdev)
>>>>        thermal->chip->initialize(thermal->grf, thermal->regs,
>>>>                      thermal->tshut_polarity);
>>>>    +    if (thermal->tshut_mode == TSHUT_MODE_OTP) {
>>>> +        thermal->pinctrl = devm_pinctrl_get(&pdev->dev);
>>>> +        if (IS_ERR(thermal->pinctrl))
>>>> +            dev_err(&pdev->dev, "failed to find thermal pinctrl\n");
>>>> +
>>>> +        thermal->gpio_state = pinctrl_lookup_state(thermal->pinctrl,
>>>> +                               "gpio");
> panic if devm_pinctrl_get fails.
OK, It's good advice. I'll fix it in the V2.
>
>>>> +        if (IS_ERR_OR_NULL(thermal->gpio_state))
>>>> +            dev_err(&pdev->dev, "failed to find thermal gpio state\n");
>>>> +
>>>> +        thermal->otp_state = pinctrl_lookup_state(thermal->pinctrl,
>>>> +                              "otpout");
>>>> +        if (IS_ERR_OR_NULL(thermal->otp_state))
>>>> +            dev_err(&pdev->dev, "failed to find thermal otpout
>>>> state\n");
>>> What is the meaning for the rest of the code if the lookup fails for any
>>> of those ?
>> If the lookup fails for any of those, The pinctrl is no longer set and
>> remains in its default state(otp_gpio normal io).
>>>> +        thermal_pinctrl_select_otp(thermal);
>>>> +    }
>>>> +
> It is pointless to have a otp_state and a gpio_state field. Just use one
> as the configuration tells you which lookup to do.
>
> In case of error, just bail out. It is pointless to continue with a
> broken configuration.
If the DST node is not modified synchronously, which may cause the 
rockchip_thermal driver probe failed.
Should I ignore this?
>
> 	thermal->pinctrl = devm_pinctrl_get(&pdev->dev);
> 	if (IS_ERR(thermal->pinctrl)) {
> 		dev_err(&pdev->dev, "....");
> 		return PTR_ERR(thermal->pinctrl);
> 	}
>
> 	thermal->pinctrl_state =
> 		pinctrl_lookup_state(thermal->pinctrl,
> 			thermal->tshut_mode == TSHUT_MODE_OTP ?
> 			"otp" : "gpio");
>
> 	if (IS_ERR_OR_NULL(thermal->pinctrl_state)) {
> 		dev_err(&pdev->dev, "....");
> 		return -EINVAL;
> 	}
>
>
> No need to use the thermal_pinctrl_select_otp/gpio wrappers, just
> replace them with:
>
> pinctrl_select_state(thermal->pinctrl, thermal->pinctrl_state);
>
> and use it unconditionally.
OK. I'll fix it in the V2.
>
>
>>>>        for (i = 0; i < thermal->chip->chn_num; i++) {
>>>>            error = rockchip_thermal_register_sensor(pdev, thermal,
>>>>                            &thermal->sensors[i],
>>>> @@ -1338,7 +1375,8 @@ static int __maybe_unused
>>>> rockchip_thermal_suspend(struct device *dev)
>>>>        clk_disable(thermal->pclk);
>>>>        clk_disable(thermal->clk);
>>>>    -    pinctrl_pm_select_sleep_state(dev);
>>>> +    if (thermal->tshut_mode == TSHUT_MODE_OTP)
>>>> +        thermal_pinctrl_select_gpio(thermal);
>>>>          return 0;
>>>>    }
>>>> @@ -1383,7 +1421,8 @@ static int __maybe_unused
>>>> rockchip_thermal_resume(struct device *dev)
>>>>        for (i = 0; i < thermal->chip->chn_num; i++)
>>>>            rockchip_thermal_toggle_sensor(&thermal->sensors[i], true);
>>>>    -    pinctrl_pm_select_default_state(dev);
>>>> +    if (thermal->tshut_mode == TSHUT_MODE_OTP)
>>>> +        thermal_pinctrl_select_otp(thermal);
>>>>          return 0;
>>>>    }
>>>>
>>
>

Patch
diff mbox series

diff --git a/drivers/thermal/rockchip_thermal.c b/drivers/thermal/rockchip_thermal.c
index 9c7643d62ed7..faa6c7792155 100644
--- a/drivers/thermal/rockchip_thermal.c
+++ b/drivers/thermal/rockchip_thermal.c
@@ -34,7 +34,7 @@ 
  */
 enum tshut_mode {
 	TSHUT_MODE_CRU = 0,
-	TSHUT_MODE_GPIO,
+	TSHUT_MODE_OTP,
 };
 
 /**
@@ -172,6 +172,9 @@  struct rockchip_thermal_data {
 	int tshut_temp;
 	enum tshut_mode tshut_mode;
 	enum tshut_polarity tshut_polarity;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state *gpio_state;
+	struct pinctrl_state *otp_state;
 };
 
 /**
@@ -807,7 +810,7 @@  static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
 	u32 val;
 
 	val = readl_relaxed(regs + TSADCV2_INT_EN);
-	if (mode == TSHUT_MODE_GPIO) {
+	if (mode == TSHUT_MODE_OTP) {
 		val &= ~TSADCV2_SHUT_2CRU_SRC_EN(chn);
 		val |= TSADCV2_SHUT_2GPIO_SRC_EN(chn);
 	} else {
@@ -822,7 +825,7 @@  static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
 	.chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
 	.chn_num = 1, /* one channel for tsadc */
 
-	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
+	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
 	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
 	.tshut_temp = 95000,
 
@@ -846,7 +849,7 @@  static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
 	.chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
 	.chn_num = 1, /* one channel for tsadc */
 
-	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
+	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
 	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
 	.tshut_temp = 95000,
 
@@ -871,7 +874,7 @@  static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
 	.chn_id[SENSOR_GPU] = 2, /* gpu sensor is channel 2 */
 	.chn_num = 2, /* two channels for tsadc */
 
-	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
+	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
 	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
 	.tshut_temp = 95000,
 
@@ -919,7 +922,7 @@  static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
 	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
 	.chn_num = 2, /* two channels for tsadc */
 
-	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
+	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
 	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
 	.tshut_temp = 95000,
 
@@ -944,7 +947,7 @@  static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
 	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
 	.chn_num = 2, /* two channels for tsadc */
 
-	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
+	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
 	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
 	.tshut_temp = 95000,
 
@@ -969,7 +972,7 @@  static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
 	.chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
 	.chn_num = 2, /* two channels for tsadc */
 
-	.tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
+	.tshut_mode = TSHUT_MODE_OTP, /* default TSHUT via GPIO give PMIC */
 	.tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
 	.tshut_temp = 95000,
 
@@ -1080,6 +1083,20 @@  static int rockchip_thermal_get_temp(void *_sensor, int *out_temp)
 	.set_trips = rockchip_thermal_set_trips,
 };
 
+static void thermal_pinctrl_select_otp(struct rockchip_thermal_data *thermal)
+{
+	if (!IS_ERR(thermal->pinctrl) && !IS_ERR_OR_NULL(thermal->otp_state))
+		pinctrl_select_state(thermal->pinctrl,
+				     thermal->otp_state);
+}
+
+static void thermal_pinctrl_select_gpio(struct rockchip_thermal_data *thermal)
+{
+	if (!IS_ERR(thermal->pinctrl) && !IS_ERR_OR_NULL(thermal->gpio_state))
+		pinctrl_select_state(thermal->pinctrl,
+				     thermal->gpio_state);
+}
+
 static int rockchip_configure_from_dt(struct device *dev,
 				      struct device_node *np,
 				      struct rockchip_thermal_data *thermal)
@@ -1103,7 +1120,7 @@  static int rockchip_configure_from_dt(struct device *dev,
 	if (of_property_read_u32(np, "rockchip,hw-tshut-mode", &tshut_mode)) {
 		dev_warn(dev,
 			 "Missing tshut mode property, using default (%s)\n",
-			 thermal->chip->tshut_mode == TSHUT_MODE_GPIO ?
+			 thermal->chip->tshut_mode == TSHUT_MODE_OTP ?
 				"gpio" : "cru");
 		thermal->tshut_mode = thermal->chip->tshut_mode;
 	} else {
@@ -1242,6 +1259,8 @@  static int rockchip_thermal_probe(struct platform_device *pdev)
 		return error;
 	}
 
+	thermal->chip->control(thermal->regs, false);
+
 	error = clk_prepare_enable(thermal->clk);
 	if (error) {
 		dev_err(&pdev->dev, "failed to enable converter clock: %d\n",
@@ -1267,6 +1286,24 @@  static int rockchip_thermal_probe(struct platform_device *pdev)
 	thermal->chip->initialize(thermal->grf, thermal->regs,
 				  thermal->tshut_polarity);
 
+	if (thermal->tshut_mode == TSHUT_MODE_OTP) {
+		thermal->pinctrl = devm_pinctrl_get(&pdev->dev);
+		if (IS_ERR(thermal->pinctrl))
+			dev_err(&pdev->dev, "failed to find thermal pinctrl\n");
+
+		thermal->gpio_state = pinctrl_lookup_state(thermal->pinctrl,
+							   "gpio");
+		if (IS_ERR_OR_NULL(thermal->gpio_state))
+			dev_err(&pdev->dev, "failed to find thermal gpio state\n");
+
+		thermal->otp_state = pinctrl_lookup_state(thermal->pinctrl,
+							  "otpout");
+		if (IS_ERR_OR_NULL(thermal->otp_state))
+			dev_err(&pdev->dev, "failed to find thermal otpout state\n");
+
+		thermal_pinctrl_select_otp(thermal);
+	}
+
 	for (i = 0; i < thermal->chip->chn_num; i++) {
 		error = rockchip_thermal_register_sensor(pdev, thermal,
 						&thermal->sensors[i],
@@ -1338,7 +1375,8 @@  static int __maybe_unused rockchip_thermal_suspend(struct device *dev)
 	clk_disable(thermal->pclk);
 	clk_disable(thermal->clk);
 
-	pinctrl_pm_select_sleep_state(dev);
+	if (thermal->tshut_mode == TSHUT_MODE_OTP)
+		thermal_pinctrl_select_gpio(thermal);
 
 	return 0;
 }
@@ -1383,7 +1421,8 @@  static int __maybe_unused rockchip_thermal_resume(struct device *dev)
 	for (i = 0; i < thermal->chip->chn_num; i++)
 		rockchip_thermal_toggle_sensor(&thermal->sensors[i], true);
 
-	pinctrl_pm_select_default_state(dev);
+	if (thermal->tshut_mode == TSHUT_MODE_OTP)
+		thermal_pinctrl_select_otp(thermal);
 
 	return 0;
 }