@@ -22,6 +22,11 @@ Optional properties:
2: Use JD1_2 pin for jack-detect
3: Use JD2 pin for jack-detect
+- realtek,jack-detect-not-inverted
+ bool. Normal jack-detect switches give an inverted (active-low) signal,
+ set this bool in the rare case you've a jack-detect switch which is not
+ inverted.
+
- realtek,over-current-threshold-microamp
u32, micbias over-current detection threshold in µA, valid values are
600, 1500 and 2000µA.
@@ -1645,7 +1645,10 @@ static bool rt5651_jack_inserted(struct snd_soc_component *component)
break;
}
- return val == 0;
+ if (rt5651->jd_active_high)
+ return val != 0;
+ else
+ return val == 0;
}
/* Jack detect and button-press timings */
@@ -1868,20 +1871,47 @@ static void rt5651_enable_jack_detect(struct snd_soc_component *component,
case RT5651_JD1_1:
snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD1_1);
- snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
- RT5651_JD1_1_IRQ_EN, RT5651_JD1_1_IRQ_EN);
+ /* active-low is normal, set inv flag for active-high */
+ if (rt5651->jd_active_high)
+ snd_soc_component_update_bits(component,
+ RT5651_IRQ_CTRL1,
+ RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV,
+ RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV);
+ else
+ snd_soc_component_update_bits(component,
+ RT5651_IRQ_CTRL1,
+ RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV,
+ RT5651_JD1_1_IRQ_EN);
break;
case RT5651_JD1_2:
snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD1_2);
- snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
- RT5651_JD1_2_IRQ_EN, RT5651_JD1_2_IRQ_EN);
+ /* active-low is normal, set inv flag for active-high */
+ if (rt5651->jd_active_high)
+ snd_soc_component_update_bits(component,
+ RT5651_IRQ_CTRL1,
+ RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV,
+ RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV);
+ else
+ snd_soc_component_update_bits(component,
+ RT5651_IRQ_CTRL1,
+ RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV,
+ RT5651_JD1_2_IRQ_EN);
break;
case RT5651_JD2:
snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD2);
- snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
- RT5651_JD2_IRQ_EN, RT5651_JD2_IRQ_EN);
+ /* active-low is normal, set inv flag for active-high */
+ if (rt5651->jd_active_high)
+ snd_soc_component_update_bits(component,
+ RT5651_IRQ_CTRL1,
+ RT5651_JD2_IRQ_EN | RT5651_JD2_INV,
+ RT5651_JD2_IRQ_EN | RT5651_JD2_INV);
+ else
+ snd_soc_component_update_bits(component,
+ RT5651_IRQ_CTRL1,
+ RT5651_JD2_IRQ_EN | RT5651_JD2_INV,
+ RT5651_JD2_IRQ_EN);
break;
default:
dev_err(component->dev, "Currently only JD1_1 / JD1_2 / JD2 are supported\n");
@@ -1986,6 +2016,9 @@ static void rt5651_apply_properties(struct snd_soc_component *component)
"realtek,jack-detect-source", &val) == 0)
rt5651->jd_src = val;
+ if (device_property_read_bool(component->dev, "realtek,jack-detect-not-inverted"))
+ rt5651->jd_active_high = true;
+
/*
* Testing on various boards has shown that good defaults for the OVCD
* threshold and scale-factor are 2000µA and 0.75. For an effective
@@ -2083,6 +2083,7 @@ struct rt5651_priv {
int release_count;
int poll_count;
unsigned int jd_src;
+ bool jd_active_high;
unsigned int ovcd_th;
unsigned int ovcd_sf;
Some boards use a jack-receptacle with a switch which reports the jack-inserted status as active-high, rather then the standard active-low reporting most jacks use. This commit adds support for it. This is activated by a boolean "realtek,jack-detect-not-inverted" device-property. The not-inverted in the device-property name, rather then active-high, was chosen to keep the device-property naming consistent with the rt5640 codec driver. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- .../devicetree/bindings/sound/rt5651.txt | 5 ++ sound/soc/codecs/rt5651.c | 47 ++++++++++++++++--- sound/soc/codecs/rt5651.h | 1 + 3 files changed, 46 insertions(+), 7 deletions(-)