diff mbox series

[v1,1/4] dt-bindings: display: Add DT bindings for LS1028A HDP-TX PHY.

Message ID 20190508103703.40885-1-wen.he_1@nxp.com (mailing list archive)
State New, archived
Headers show
Series [v1,1/4] dt-bindings: display: Add DT bindings for LS1028A HDP-TX PHY. | expand

Commit Message

Wen He May 8, 2019, 10:35 a.m. UTC 
Add DT bindings documentmation for the HDP-TX PHY controller. The describes
which could be found on NXP Layerscape ls1028a platform.

Signed-off-by: Wen He <wen.he_1@nxp.com>
---
 .../devicetree/bindings/display/fsl,hdp.txt   | 56 +++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/fsl,hdp.txt

Comments

Rob Herring (Arm) June 13, 2019, 8:08 p.m. UTC | #1 
On Wed, May 08, 2019 at 10:35:25AM +0000, Wen He wrote:
> Add DT bindings documentmation for the HDP-TX PHY controller. The describes
> which could be found on NXP Layerscape ls1028a platform.

Drop the hard stop (.) from the subject.

> 
> Signed-off-by: Wen He <wen.he_1@nxp.com>
> ---
>  .../devicetree/bindings/display/fsl,hdp.txt   | 56 +++++++++++++++++++
>  1 file changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/fsl,hdp.txt
> 
> diff --git a/Documentation/devicetree/bindings/display/fsl,hdp.txt b/Documentation/devicetree/bindings/display/fsl,hdp.txt
> new file mode 100644
> index 000000000000..36b5687a1261
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/fsl,hdp.txt
> @@ -0,0 +1,56 @@
> +NXP Layerscpae ls1028a HDP-TX PHY Controller
> +============================================
> +
> +The following bindings describe the Cadence HDP TX PHY on ls1028a that
> +offer multi-protocol support of standars such as eDP and Displayport,
> +supports for 25-600MHz pixel clock and up to 4k2k at 60MHz resolution.
> +The HDP transmitter is a Cadence HDP TX controller IP with a companion
> +PHY IP.

I'm confused. This binding covers both blocks or is just one of them?

> +
> +Required properties:
> +  - compatible:   Should be "fsl,ls1028a-dp" for ls1028a.
> +  - reg:          Physical base address and size of the block of registers used
> +  by the processor.
> +  - interrupts:   HDP hotplug in/out detect interrupt number
> +  - clocks:       A list of phandle + clock-specifier pairs, one for each entry
> +  in 'clock-names'
> +  - clock-names:  A list of clock names. It should contain:
> +      - "clk_ipg": inter-Integrated circuit clock
> +      - "clk_core": for the Main Display TX controller clock
> +      - "clk_pxl": for the pixel clock feeding the output PLL of the processor
> +      - "clk_pxl_mux": for the high PerfPLL bypass clock
> +      - "clk_pxl_link": for the link rate pixel clock
> +      - "clk_apb": for the APB interface clock
> +      - "clk_vif": for the Video pixel clock

The 'clk_' part is redundant.

> +
> +Required sub-nodes:
> +  - port: The HDP connection to an encoder output port. The connection
> +    is modelled using the OF graph bindings specified in
> +    Documentation/devicetree/bindings/graph.txt
> +
> +
> +Example:
> +
> +/ {
> +        ...
> +
> +	hdp: display@f200000 {
> +                compatible = "fsl,ls1028a-dp";
> +		reg = <0x0 0xf1f0000 0x0 0xffff>,
> +		    <0x0 0xf200000 0x0 0xfffff>;
> +                interrupts = <0 221 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&sysclk>, <&hdpclk>, <&dpclk>,
> +                         <&dpclk>, <&dpclk>, <&pclk>, <&dpclk>;
> +		clock-names = "clk_ipg", "clk_core", "clk_pxl",
> +                              "clk_pxl_mux", "clk_pxl_link", "clk_apb",
> +                              "clk_vif";
> +
> +		port {
> +			dp1_output: endpoint {
> +				remote-endpoint = <&dp0_input>;
> +			};
> +		};
> +        };
> +
> +        ...
> +};
> -- 
> 2.17.1
>
Wen He June 17, 2019, 1:45 a.m. UTC | #2 
> -----Original Message-----
> From: Rob Herring <robh@kernel.org>
> Sent: 2019年6月14日 4:08
> To: Wen He <wen.he_1@nxp.com>
> Cc: linux-kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org;
> devicetree@vger.kernel.org; shawnguo@kernel.org; Leo Li
> <leoyang.li@nxp.com>
> Subject: [EXT] Re: [v1 1/4] dt-bindings: display: Add DT bindings for LS1028A
> HDP-TX PHY.
> 
> Caution: EXT Email
> 
> On Wed, May 08, 2019 at 10:35:25AM +0000, Wen He wrote:
> > Add DT bindings documentmation for the HDP-TX PHY controller. The
> > describes which could be found on NXP Layerscape ls1028a platform.
> 
> Drop the hard stop (.) from the subject.
> 
> >
> > Signed-off-by: Wen He <wen.he_1@nxp.com>
> > ---
> >  .../devicetree/bindings/display/fsl,hdp.txt   | 56 +++++++++++++++++++
> >  1 file changed, 56 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/display/fsl,hdp.txt
> >
> > diff --git a/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > b/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > new file mode 100644
> > index 000000000000..36b5687a1261
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > @@ -0,0 +1,56 @@
> > +NXP Layerscpae ls1028a HDP-TX PHY Controller
> > +============================================
> > +
> > +The following bindings describe the Cadence HDP TX PHY on ls1028a
> > +that offer multi-protocol support of standars such as eDP and
> > +Displayport, supports for 25-600MHz pixel clock and up to 4k2k at 60MHz
> resolution.
> > +The HDP transmitter is a Cadence HDP TX controller IP with a
> > +companion PHY IP.
> 
> I'm confused. This binding covers both blocks or is just one of them?
> 

Hi Rob,

This binding covers both blocks(HDP TX PHY and HDP TX Controller), 
Because they are belong to the one IP.

> > +
> > +Required properties:
> > +  - compatible:   Should be "fsl,ls1028a-dp" for ls1028a.
> > +  - reg:          Physical base address and size of the block of registers
> used
> > +  by the processor.
> > +  - interrupts:   HDP hotplug in/out detect interrupt number
> > +  - clocks:       A list of phandle + clock-specifier pairs, one for each
> entry
> > +  in 'clock-names'
> > +  - clock-names:  A list of clock names. It should contain:
> > +      - "clk_ipg": inter-Integrated circuit clock
> > +      - "clk_core": for the Main Display TX controller clock
> > +      - "clk_pxl": for the pixel clock feeding the output PLL of the processor
> > +      - "clk_pxl_mux": for the high PerfPLL bypass clock
> > +      - "clk_pxl_link": for the link rate pixel clock
> > +      - "clk_apb": for the APB interface clock
> > +      - "clk_vif": for the Video pixel clock
> 
> The 'clk_' part is redundant.
> 

You mean should I remove these 'clk_' part?

Thanks for the review.

Best Regards,
Wen

> > +
> > +Required sub-nodes:
> > +  - port: The HDP connection to an encoder output port. The connection
> > +    is modelled using the OF graph bindings specified in
> > +    Documentation/devicetree/bindings/graph.txt
> > +
> > +
> > +Example:
> > +
> > +/ {
> > +        ...
> > +
> > +     hdp: display@f200000 {
> > +                compatible = "fsl,ls1028a-dp";
> > +             reg = <0x0 0xf1f0000 0x0 0xffff>,
> > +                 <0x0 0xf200000 0x0 0xfffff>;
> > +                interrupts = <0 221 IRQ_TYPE_LEVEL_HIGH>;
> > +             clocks = <&sysclk>, <&hdpclk>, <&dpclk>,
> > +                         <&dpclk>, <&dpclk>, <&pclk>, <&dpclk>;
> > +             clock-names = "clk_ipg", "clk_core", "clk_pxl",
> > +                              "clk_pxl_mux", "clk_pxl_link", "clk_apb",
> > +                              "clk_vif";
> > +
> > +             port {
> > +                     dp1_output: endpoint {
> > +                             remote-endpoint = <&dp0_input>;
> > +                     };
> > +             };
> > +        };
> > +
> > +        ...
> > +};
> > --
> > 2.17.1
> >
Rob Herring (Arm) June 19, 2019, 2:07 p.m. UTC | #3 
On Sun, Jun 16, 2019 at 7:45 PM Wen He <wen.he_1@nxp.com> wrote:
>
>
>
> > -----Original Message-----
> > From: Rob Herring <robh@kernel.org>
> > Sent: 2019年6月14日 4:08
> > To: Wen He <wen.he_1@nxp.com>
> > Cc: linux-kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org;
> > devicetree@vger.kernel.org; shawnguo@kernel.org; Leo Li
> > <leoyang.li@nxp.com>
> > Subject: [EXT] Re: [v1 1/4] dt-bindings: display: Add DT bindings for LS1028A
> > HDP-TX PHY.
> >
> > Caution: EXT Email
> >
> > On Wed, May 08, 2019 at 10:35:25AM +0000, Wen He wrote:
> > > Add DT bindings documentmation for the HDP-TX PHY controller. The
> > > describes which could be found on NXP Layerscape ls1028a platform.
> >
> > Drop the hard stop (.) from the subject.
> >
> > >
> > > Signed-off-by: Wen He <wen.he_1@nxp.com>
> > > ---
> > >  .../devicetree/bindings/display/fsl,hdp.txt   | 56 +++++++++++++++++++
> > >  1 file changed, 56 insertions(+)
> > >  create mode 100644
> > > Documentation/devicetree/bindings/display/fsl,hdp.txt
> > >
> > > diff --git a/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > > b/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > > new file mode 100644
> > > index 000000000000..36b5687a1261
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > > @@ -0,0 +1,56 @@
> > > +NXP Layerscpae ls1028a HDP-TX PHY Controller
> > > +============================================
> > > +
> > > +The following bindings describe the Cadence HDP TX PHY on ls1028a
> > > +that offer multi-protocol support of standars such as eDP and
> > > +Displayport, supports for 25-600MHz pixel clock and up to 4k2k at 60MHz
> > resolution.
> > > +The HDP transmitter is a Cadence HDP TX controller IP with a
> > > +companion PHY IP.
> >
> > I'm confused. This binding covers both blocks or is just one of them?
> >
>
> Hi Rob,
>
> This binding covers both blocks(HDP TX PHY and HDP TX Controller),
> Because they are belong to the one IP.

In that case, you should also have an output port to a DP connector
node (or DP panel).

Rob
Wen He June 20, 2019, 3:35 a.m. UTC | #4 
> -----Original Message-----
> From: Rob Herring <robh@kernel.org>
> Sent: 2019年6月19日 22:07
> To: Wen He <wen.he_1@nxp.com>
> Cc: linux-kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org;
> devicetree@vger.kernel.org; shawnguo@kernel.org; Leo Li
> <leoyang.li@nxp.com>
> Subject: Re: [EXT] Re: [v1 1/4] dt-bindings: display: Add DT bindings for
> LS1028A HDP-TX PHY.
> 
> Caution: EXT Email
> 
> On Sun, Jun 16, 2019 at 7:45 PM Wen He <wen.he_1@nxp.com> wrote:
> >
> >
> >
> > > -----Original Message-----
> > > From: Rob Herring <robh@kernel.org>
> > > Sent: 2019年6月14日 4:08
> > > To: Wen He <wen.he_1@nxp.com>
> > > Cc: linux-kernel@vger.kernel.org;
> > > linux-arm-kernel@lists.infradead.org;
> > > devicetree@vger.kernel.org; shawnguo@kernel.org; Leo Li
> > > <leoyang.li@nxp.com>
> > > Subject: [EXT] Re: [v1 1/4] dt-bindings: display: Add DT bindings
> > > for LS1028A HDP-TX PHY.
> > >
> > > Caution: EXT Email
> > >
> > > On Wed, May 08, 2019 at 10:35:25AM +0000, Wen He wrote:
> > > > Add DT bindings documentmation for the HDP-TX PHY controller. The
> > > > describes which could be found on NXP Layerscape ls1028a platform.
> > >
> > > Drop the hard stop (.) from the subject.
> > >
> > > >
> > > > Signed-off-by: Wen He <wen.he_1@nxp.com>
> > > > ---
> > > >  .../devicetree/bindings/display/fsl,hdp.txt   | 56
> +++++++++++++++++++
> > > >  1 file changed, 56 insertions(+)
> > > >  create mode 100644
> > > > Documentation/devicetree/bindings/display/fsl,hdp.txt
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > > > b/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > > > new file mode 100644
> > > > index 000000000000..36b5687a1261
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/display/fsl,hdp.txt
> > > > @@ -0,0 +1,56 @@
> > > > +NXP Layerscpae ls1028a HDP-TX PHY Controller
> > > > +============================================
> > > > +
> > > > +The following bindings describe the Cadence HDP TX PHY on ls1028a
> > > > +that offer multi-protocol support of standars such as eDP and
> > > > +Displayport, supports for 25-600MHz pixel clock and up to 4k2k at
> > > > +60MHz
> > > resolution.
> > > > +The HDP transmitter is a Cadence HDP TX controller IP with a
> > > > +companion PHY IP.
> > >
> > > I'm confused. This binding covers both blocks or is just one of them?
> > >
> >
> > Hi Rob,
> >
> > This binding covers both blocks(HDP TX PHY and HDP TX Controller),
> > Because they are belong to the one IP.
> 
> In that case, you should also have an output port to a DP connector node (or
> DP panel).

Hi Rob,

I remember there are included the DP connector node description as see below.

---
Required sub-nodes:
- port

It there should be right?

Best Regards,
Wen

> 
> Rob
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/display/fsl,hdp.txt b/Documentation/devicetree/bindings/display/fsl,hdp.txt
new file mode 100644
index 000000000000..36b5687a1261
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/fsl,hdp.txt
@@ -0,0 +1,56 @@ 
+NXP Layerscpae ls1028a HDP-TX PHY Controller
+============================================
+
+The following bindings describe the Cadence HDP TX PHY on ls1028a that
+offer multi-protocol support of standars such as eDP and Displayport,
+supports for 25-600MHz pixel clock and up to 4k2k at 60MHz resolution.
+The HDP transmitter is a Cadence HDP TX controller IP with a companion
+PHY IP.
+
+Required properties:
+  - compatible:   Should be "fsl,ls1028a-dp" for ls1028a.
+  - reg:          Physical base address and size of the block of registers used
+  by the processor.
+  - interrupts:   HDP hotplug in/out detect interrupt number
+  - clocks:       A list of phandle + clock-specifier pairs, one for each entry
+  in 'clock-names'
+  - clock-names:  A list of clock names. It should contain:
+      - "clk_ipg": inter-Integrated circuit clock
+      - "clk_core": for the Main Display TX controller clock
+      - "clk_pxl": for the pixel clock feeding the output PLL of the processor
+      - "clk_pxl_mux": for the high PerfPLL bypass clock
+      - "clk_pxl_link": for the link rate pixel clock
+      - "clk_apb": for the APB interface clock
+      - "clk_vif": for the Video pixel clock
+
+Required sub-nodes:
+  - port: The HDP connection to an encoder output port. The connection
+    is modelled using the OF graph bindings specified in
+    Documentation/devicetree/bindings/graph.txt
+
+
+Example:
+
+/ {
+        ...
+
+	hdp: display@f200000 {
+                compatible = "fsl,ls1028a-dp";
+		reg = <0x0 0xf1f0000 0x0 0xffff>,
+		    <0x0 0xf200000 0x0 0xfffff>;
+                interrupts = <0 221 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sysclk>, <&hdpclk>, <&dpclk>,
+                         <&dpclk>, <&dpclk>, <&pclk>, <&dpclk>;
+		clock-names = "clk_ipg", "clk_core", "clk_pxl",
+                              "clk_pxl_mux", "clk_pxl_link", "clk_apb",
+                              "clk_vif";
+
+		port {
+			dp1_output: endpoint {
+				remote-endpoint = <&dp0_input>;
+			};
+		};
+        };
+
+        ...
+};