| Message ID | 20190510164940.13496-3-jbrunet@baylibre.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: meson: g12a: add network support | expand |
Hi Jerome, On Fri, May 10, 2019 at 6:49 PM Jerome Brunet <jbrunet@baylibre.com> wrote: > > Add the ethernet pinctrl settings for RMII, RGMII and internal phy leds > > Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> > --- > arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 37 +++++++++++++++++++++ > 1 file changed, 37 insertions(+) > > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi > index a32db09809f7..fe0f73730525 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi > +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi > @@ -206,6 +206,43 @@ > }; > }; > > + eth_leds_pins: eth-leds { > + mux { > + groups = "eth_link_led", > + "eth_act_led"; > + function = "eth"; > + bias-disable; > + }; > + }; > + > + eth_rmii_pins: eth-rmii { > + mux { > + groups = "eth_mdio", > + "eth_mdc", > + "eth_rgmii_rx_clk", > + "eth_rx_dv", > + "eth_rxd0", > + "eth_rxd1", > + "eth_txen", > + "eth_txd0", > + "eth_txd1"; > + function = "eth"; > + bias-disable; > + }; > + }; > + > + eth_rgmii_pins: eth-rgmii { > + mux { > + groups = "eth_rxd2_rgmii", > + "eth_rxd3_rgmii", > + "eth_rgmii_tx_clk", > + "eth_txd2_rgmii", > + "eth_txd3_rgmii"; > + function = "eth"; > + bias-disable; > + }; > + }; it seems that the group definition is incomplete (missing things like eth_mdc, eth_rx_dv, ...) we could also mix the eth_rmii_pins and eth_rgmii_pins in a board.dts (maybe that was your idea in the first place?): phy-mode = "rgmii"; pinctrl-0 = <ð_rmii_pins>, <ð_rgmii_pins>; pinctrl-names = "default"; however, in this case I would prefer if "eth_rmii_pins" was named only "eth_pins" (following mostly what Amlogic does with the pin group naming: eth_* for pins that are valid in both, rmii and rgmii mode and eth*rgmii* for pins that are only valid in rgmii mode) Regards Martin
On Sat, 2019-05-11 at 19:06 +0200, Martin Blumenstingl wrote: > Hi Jerome, > > On Fri, May 10, 2019 at 6:49 PM Jerome Brunet <jbrunet@baylibre.com> wrote: > > Add the ethernet pinctrl settings for RMII, RGMII and internal phy leds > > > > Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> > > --- > > arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 37 +++++++++++++++++++++ > > 1 file changed, 37 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi > > index a32db09809f7..fe0f73730525 100644 > > --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi > > +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi > > @@ -206,6 +206,43 @@ > > }; > > }; > > > > + eth_leds_pins: eth-leds { > > + mux { > > + groups = "eth_link_led", > > + "eth_act_led"; > > + function = "eth"; > > + bias-disable; > > + }; > > + }; > > + > > + eth_rmii_pins: eth-rmii { > > + mux { > > + groups = "eth_mdio", > > + "eth_mdc", > > + "eth_rgmii_rx_clk", > > + "eth_rx_dv", > > + "eth_rxd0", > > + "eth_rxd1", > > + "eth_txen", > > + "eth_txd0", > > + "eth_txd1"; > > + function = "eth"; > > + bias-disable; > > + }; > > + }; > > + > > + eth_rgmii_pins: eth-rgmii { > > + mux { > > + groups = "eth_rxd2_rgmii", > > + "eth_rxd3_rgmii", > > + "eth_rgmii_tx_clk", > > + "eth_txd2_rgmii", > > + "eth_txd3_rgmii"; > > + function = "eth"; > > + bias-disable; > > + }; > > + }; > it seems that the group definition is incomplete (missing things like > eth_mdc, eth_rx_dv, ...) > > we could also mix the eth_rmii_pins and eth_rgmii_pins in a board.dts > (maybe that was your idea in the first place?): yes that's the idea > phy-mode = "rgmii"; > pinctrl-0 = <ð_rmii_pins>, <ð_rgmii_pins>; > pinctrl-names = "default"; > however, in this case I would prefer if "eth_rmii_pins" was named only > "eth_pins" (following mostly what Amlogic does with the pin group > naming: eth_* for pins that are valid in both, rmii and rgmii mode and > eth*rgmii* for pins that are only valid in rgmii mode) I can't say I share your preference. I let Kevin decide what he wants. > > > Regards > Martin
Jerome Brunet <jbrunet@baylibre.com> writes: > On Sat, 2019-05-11 at 19:06 +0200, Martin Blumenstingl wrote: >> Hi Jerome, >> >> On Fri, May 10, 2019 at 6:49 PM Jerome Brunet <jbrunet@baylibre.com> wrote: >> > Add the ethernet pinctrl settings for RMII, RGMII and internal phy leds >> > >> > Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> >> > --- >> > arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 37 +++++++++++++++++++++ >> > 1 file changed, 37 insertions(+) >> > >> > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi >> > index a32db09809f7..fe0f73730525 100644 >> > --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi >> > +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi >> > @@ -206,6 +206,43 @@ >> > }; >> > }; >> > >> > + eth_leds_pins: eth-leds { >> > + mux { >> > + groups = "eth_link_led", >> > + "eth_act_led"; >> > + function = "eth"; >> > + bias-disable; >> > + }; >> > + }; >> > + >> > + eth_rmii_pins: eth-rmii { >> > + mux { >> > + groups = "eth_mdio", >> > + "eth_mdc", >> > + "eth_rgmii_rx_clk", >> > + "eth_rx_dv", >> > + "eth_rxd0", >> > + "eth_rxd1", >> > + "eth_txen", >> > + "eth_txd0", >> > + "eth_txd1"; >> > + function = "eth"; >> > + bias-disable; >> > + }; >> > + }; >> > + >> > + eth_rgmii_pins: eth-rgmii { >> > + mux { >> > + groups = "eth_rxd2_rgmii", >> > + "eth_rxd3_rgmii", >> > + "eth_rgmii_tx_clk", >> > + "eth_txd2_rgmii", >> > + "eth_txd3_rgmii"; >> > + function = "eth"; >> > + bias-disable; >> > + }; >> > + }; >> it seems that the group definition is incomplete (missing things like >> eth_mdc, eth_rx_dv, ...) >> >> we could also mix the eth_rmii_pins and eth_rgmii_pins in a board.dts >> (maybe that was your idea in the first place?): > > yes that's the idea > >> phy-mode = "rgmii"; >> pinctrl-0 = <ð_rmii_pins>, <ð_rgmii_pins>; >> pinctrl-names = "default"; >> however, in this case I would prefer if "eth_rmii_pins" was named only >> "eth_pins" (following mostly what Amlogic does with the pin group >> naming: eth_* for pins that are valid in both, rmii and rgmii mode and >> eth*rgmii* for pins that are only valid in rgmii mode) > > I can't say I share your preference. I let Kevin decide what he wants. > It seems we've gone the eth_pins route for meson-gxl.dtsi, so I'd prefer to be consistent with that. Kevin
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi index a32db09809f7..fe0f73730525 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi @@ -206,6 +206,43 @@ }; }; + eth_leds_pins: eth-leds { + mux { + groups = "eth_link_led", + "eth_act_led"; + function = "eth"; + bias-disable; + }; + }; + + eth_rmii_pins: eth-rmii { + mux { + groups = "eth_mdio", + "eth_mdc", + "eth_rgmii_rx_clk", + "eth_rx_dv", + "eth_rxd0", + "eth_rxd1", + "eth_txen", + "eth_txd0", + "eth_txd1"; + function = "eth"; + bias-disable; + }; + }; + + eth_rgmii_pins: eth-rgmii { + mux { + groups = "eth_rxd2_rgmii", + "eth_rxd3_rgmii", + "eth_rgmii_tx_clk", + "eth_txd2_rgmii", + "eth_txd3_rgmii"; + function = "eth"; + bias-disable; + }; + }; + hdmitx_ddc_pins: hdmitx_ddc { mux { groups = "hdmitx_sda",
Add the ethernet pinctrl settings for RMII, RGMII and internal phy leds Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 37 +++++++++++++++++++++ 1 file changed, 37 insertions(+)