[v3,03/10] drm: bridge: thc63: Report input bus mode through bridge timings
diff mbox series

Message ID 20190528141234.15425-4-laurent.pinchart+renesas@ideasonboard.com
State New
Delegated to: Kieran Bingham
Headers show
Series
  • R-Car DU: LVDS dual-link mode support
Related show

Commit Message

Laurent Pinchart May 28, 2019, 2:12 p.m. UTC
Set a drm_bridge_timings in the drm_bridge, and use it to report the
input bus mode (single-link or dual-link). The other fields of the
timings structure are kept to 0 as they do not apply to LVDS buses.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
Changes since v1:

- Ignore disabled remote device
---
 drivers/gpu/drm/bridge/thc63lvd1024.c | 54 +++++++++++++++++++++------
 1 file changed, 43 insertions(+), 11 deletions(-)

Comments

Kieran Bingham June 7, 2019, 10:51 p.m. UTC | #1
Hi Laurent,

On 28/05/2019 15:12, Laurent Pinchart wrote:
> Set a drm_bridge_timings in the drm_bridge, and use it to report the
> input bus mode (single-link or dual-link). The other fields of the
> timings structure are kept to 0 as they do not apply to LVDS buses.
> 
> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

> ---
> Changes since v1:
> 
> - Ignore disabled remote device
> ---
>  drivers/gpu/drm/bridge/thc63lvd1024.c | 54 +++++++++++++++++++++------
>  1 file changed, 43 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/thc63lvd1024.c b/drivers/gpu/drm/bridge/thc63lvd1024.c
> index b083a740565c..709dd28b43d6 100644
> --- a/drivers/gpu/drm/bridge/thc63lvd1024.c
> +++ b/drivers/gpu/drm/bridge/thc63lvd1024.c
> @@ -31,6 +31,8 @@ struct thc63_dev {
>  
>  	struct drm_bridge bridge;
>  	struct drm_bridge *next;
> +
> +	struct drm_bridge_timings timings;

These are just input timings right?

>  };
>  
>  static inline struct thc63_dev *to_thc63(struct drm_bridge *bridge)
> @@ -48,15 +50,28 @@ static int thc63_attach(struct drm_bridge *bridge)
>  static enum drm_mode_status thc63_mode_valid(struct drm_bridge *bridge,
>  					const struct drm_display_mode *mode)
>  {
> +	struct thc63_dev *thc63 = to_thc63(bridge);
> +	unsigned int min_freq;
> +	unsigned int max_freq;
> +
>  	/*
> -	 * The THC63LVD1024 clock frequency range is 8 to 135 MHz in single-in
> -	 * mode. Note that the limits are different in dual-in, single-out mode,
> -	 * and will need to be adjusted accordingly.
> +	 * The THC63LVD1024 pixel rate range is 8 to 135 MHz in all modes but
> +	 * dual-in, single-out where it is 40 to 150 MHz. As dual-in, dual-out

That comma is unfortunate, and makes me read the sentence as "in all
modes but dual-in, ... ... single out where it is 40 to 150 mhz (as if
we should single out the device for it's behaviour between 40 to 150mhz).

Perhaps we could enclose the mode in single quotes to denote that it is
a single description:

   ... in all modes but 'dual-in, single-out' where it ...

> +	 * isn't supported by the driver yet, simply derive the limits from the
> +	 * input mode.
>  	 */
> -	if (mode->clock < 8000)
> +	if (thc63->timings.dual_link) {
> +		min_freq = 40000;
> +		max_freq = 150000;
> +	} else {
> +		min_freq = 8000;
> +		max_freq = 135000;
> +	}
> +
> +	if (mode->clock < min_freq)
>  		return MODE_CLOCK_LOW;
>  
> -	if (mode->clock > 135000)
> +	if (mode->clock > max_freq)
>  		return MODE_CLOCK_HIGH;
>  
>  	return MODE_OK;
> @@ -101,19 +116,19 @@ static const struct drm_bridge_funcs thc63_bridge_func = {
>  
>  static int thc63_parse_dt(struct thc63_dev *thc63)
>  {
> -	struct device_node *thc63_out;
> +	struct device_node *endpoint;
>  	struct device_node *remote;
>  
> -	thc63_out = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> -						  THC63_RGB_OUT0, -1);
> -	if (!thc63_out) {
> +	endpoint = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> +						 THC63_RGB_OUT0, -1);
> +	if (!endpoint) {
>  		dev_err(thc63->dev, "Missing endpoint in port@%u\n",
>  			THC63_RGB_OUT0);
>  		return -ENODEV;
>  	}
>  
> -	remote = of_graph_get_remote_port_parent(thc63_out);
> -	of_node_put(thc63_out);
> +	remote = of_graph_get_remote_port_parent(endpoint);
> +	of_node_put(endpoint);
>  	if (!remote) {
>  		dev_err(thc63->dev, "Endpoint in port@%u unconnected\n",
>  			THC63_RGB_OUT0);
> @@ -132,6 +147,22 @@ static int thc63_parse_dt(struct thc63_dev *thc63)
>  	if (!thc63->next)
>  		return -EPROBE_DEFER;
>  
> +	endpoint = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> +						 THC63_LVDS_IN1, -1);
> +	if (endpoint) {
> +		remote = of_graph_get_remote_port_parent(endpoint);
> +		of_node_put(endpoint);
> +
> +		if (remote) {
> +			if (of_device_is_available(remote))
> +				thc63->timings.dual_link = true;
> +			of_node_put(remote);
> +		}
> +	}
> +
> +	dev_dbg(thc63->dev, "operating in %s-link mode\n",
> +		thc63->timings.dual_link ? "dual" : "single");
> +
>  	return 0;
>  }
>  
> @@ -188,6 +219,7 @@ static int thc63_probe(struct platform_device *pdev)
>  	thc63->bridge.driver_private = thc63;
>  	thc63->bridge.of_node = pdev->dev.of_node;
>  	thc63->bridge.funcs = &thc63_bridge_func;
> +	thc63->bridge.timings = &thc63->timings;
>  
>  	drm_bridge_add(&thc63->bridge);
>  
>
Neil Armstrong July 30, 2019, 12:13 p.m. UTC | #2
On 28/05/2019 16:12, Laurent Pinchart wrote:
> Set a drm_bridge_timings in the drm_bridge, and use it to report the
> input bus mode (single-link or dual-link). The other fields of the
> timings structure are kept to 0 as they do not apply to LVDS buses.
> 
> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> ---
> Changes since v1:
> 
> - Ignore disabled remote device
> ---
>  drivers/gpu/drm/bridge/thc63lvd1024.c | 54 +++++++++++++++++++++------
>  1 file changed, 43 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/thc63lvd1024.c b/drivers/gpu/drm/bridge/thc63lvd1024.c
> index b083a740565c..709dd28b43d6 100644
> --- a/drivers/gpu/drm/bridge/thc63lvd1024.c
> +++ b/drivers/gpu/drm/bridge/thc63lvd1024.c
> @@ -31,6 +31,8 @@ struct thc63_dev {
>  
>  	struct drm_bridge bridge;
>  	struct drm_bridge *next;
> +
> +	struct drm_bridge_timings timings;
>  };
>  
>  static inline struct thc63_dev *to_thc63(struct drm_bridge *bridge)
> @@ -48,15 +50,28 @@ static int thc63_attach(struct drm_bridge *bridge)
>  static enum drm_mode_status thc63_mode_valid(struct drm_bridge *bridge,
>  					const struct drm_display_mode *mode)
>  {
> +	struct thc63_dev *thc63 = to_thc63(bridge);
> +	unsigned int min_freq;
> +	unsigned int max_freq;
> +
>  	/*
> -	 * The THC63LVD1024 clock frequency range is 8 to 135 MHz in single-in
> -	 * mode. Note that the limits are different in dual-in, single-out mode,
> -	 * and will need to be adjusted accordingly.
> +	 * The THC63LVD1024 pixel rate range is 8 to 135 MHz in all modes but
> +	 * dual-in, single-out where it is 40 to 150 MHz. As dual-in, dual-out
> +	 * isn't supported by the driver yet, simply derive the limits from the
> +	 * input mode.
>  	 */
> -	if (mode->clock < 8000)
> +	if (thc63->timings.dual_link) {
> +		min_freq = 40000;
> +		max_freq = 150000;
> +	} else {
> +		min_freq = 8000;
> +		max_freq = 135000;
> +	}
> +
> +	if (mode->clock < min_freq)
>  		return MODE_CLOCK_LOW;
>  
> -	if (mode->clock > 135000)
> +	if (mode->clock > max_freq)
>  		return MODE_CLOCK_HIGH;
>  
>  	return MODE_OK;
> @@ -101,19 +116,19 @@ static const struct drm_bridge_funcs thc63_bridge_func = {
>  
>  static int thc63_parse_dt(struct thc63_dev *thc63)
>  {
> -	struct device_node *thc63_out;
> +	struct device_node *endpoint;
>  	struct device_node *remote;
>  
> -	thc63_out = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> -						  THC63_RGB_OUT0, -1);
> -	if (!thc63_out) {
> +	endpoint = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> +						 THC63_RGB_OUT0, -1);
> +	if (!endpoint) {
>  		dev_err(thc63->dev, "Missing endpoint in port@%u\n",
>  			THC63_RGB_OUT0);
>  		return -ENODEV;
>  	}
>  
> -	remote = of_graph_get_remote_port_parent(thc63_out);
> -	of_node_put(thc63_out);
> +	remote = of_graph_get_remote_port_parent(endpoint);
> +	of_node_put(endpoint);
>  	if (!remote) {
>  		dev_err(thc63->dev, "Endpoint in port@%u unconnected\n",
>  			THC63_RGB_OUT0);
> @@ -132,6 +147,22 @@ static int thc63_parse_dt(struct thc63_dev *thc63)
>  	if (!thc63->next)
>  		return -EPROBE_DEFER;
>  
> +	endpoint = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> +						 THC63_LVDS_IN1, -1);
> +	if (endpoint) {
> +		remote = of_graph_get_remote_port_parent(endpoint);
> +		of_node_put(endpoint);
> +
> +		if (remote) {
> +			if (of_device_is_available(remote))
> +				thc63->timings.dual_link = true;
> +			of_node_put(remote);
> +		}
> +	}
> +
> +	dev_dbg(thc63->dev, "operating in %s-link mode\n",
> +		thc63->timings.dual_link ? "dual" : "single");
> +
>  	return 0;
>  }
>  
> @@ -188,6 +219,7 @@ static int thc63_probe(struct platform_device *pdev)
>  	thc63->bridge.driver_private = thc63;
>  	thc63->bridge.of_node = pdev->dev.of_node;
>  	thc63->bridge.funcs = &thc63_bridge_func;
> +	thc63->bridge.timings = &thc63->timings;
>  
>  	drm_bridge_add(&thc63->bridge);
>  
> 

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

Patch
diff mbox series

diff --git a/drivers/gpu/drm/bridge/thc63lvd1024.c b/drivers/gpu/drm/bridge/thc63lvd1024.c
index b083a740565c..709dd28b43d6 100644
--- a/drivers/gpu/drm/bridge/thc63lvd1024.c
+++ b/drivers/gpu/drm/bridge/thc63lvd1024.c
@@ -31,6 +31,8 @@  struct thc63_dev {
 
 	struct drm_bridge bridge;
 	struct drm_bridge *next;
+
+	struct drm_bridge_timings timings;
 };
 
 static inline struct thc63_dev *to_thc63(struct drm_bridge *bridge)
@@ -48,15 +50,28 @@  static int thc63_attach(struct drm_bridge *bridge)
 static enum drm_mode_status thc63_mode_valid(struct drm_bridge *bridge,
 					const struct drm_display_mode *mode)
 {
+	struct thc63_dev *thc63 = to_thc63(bridge);
+	unsigned int min_freq;
+	unsigned int max_freq;
+
 	/*
-	 * The THC63LVD1024 clock frequency range is 8 to 135 MHz in single-in
-	 * mode. Note that the limits are different in dual-in, single-out mode,
-	 * and will need to be adjusted accordingly.
+	 * The THC63LVD1024 pixel rate range is 8 to 135 MHz in all modes but
+	 * dual-in, single-out where it is 40 to 150 MHz. As dual-in, dual-out
+	 * isn't supported by the driver yet, simply derive the limits from the
+	 * input mode.
 	 */
-	if (mode->clock < 8000)
+	if (thc63->timings.dual_link) {
+		min_freq = 40000;
+		max_freq = 150000;
+	} else {
+		min_freq = 8000;
+		max_freq = 135000;
+	}
+
+	if (mode->clock < min_freq)
 		return MODE_CLOCK_LOW;
 
-	if (mode->clock > 135000)
+	if (mode->clock > max_freq)
 		return MODE_CLOCK_HIGH;
 
 	return MODE_OK;
@@ -101,19 +116,19 @@  static const struct drm_bridge_funcs thc63_bridge_func = {
 
 static int thc63_parse_dt(struct thc63_dev *thc63)
 {
-	struct device_node *thc63_out;
+	struct device_node *endpoint;
 	struct device_node *remote;
 
-	thc63_out = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
-						  THC63_RGB_OUT0, -1);
-	if (!thc63_out) {
+	endpoint = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
+						 THC63_RGB_OUT0, -1);
+	if (!endpoint) {
 		dev_err(thc63->dev, "Missing endpoint in port@%u\n",
 			THC63_RGB_OUT0);
 		return -ENODEV;
 	}
 
-	remote = of_graph_get_remote_port_parent(thc63_out);
-	of_node_put(thc63_out);
+	remote = of_graph_get_remote_port_parent(endpoint);
+	of_node_put(endpoint);
 	if (!remote) {
 		dev_err(thc63->dev, "Endpoint in port@%u unconnected\n",
 			THC63_RGB_OUT0);
@@ -132,6 +147,22 @@  static int thc63_parse_dt(struct thc63_dev *thc63)
 	if (!thc63->next)
 		return -EPROBE_DEFER;
 
+	endpoint = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
+						 THC63_LVDS_IN1, -1);
+	if (endpoint) {
+		remote = of_graph_get_remote_port_parent(endpoint);
+		of_node_put(endpoint);
+
+		if (remote) {
+			if (of_device_is_available(remote))
+				thc63->timings.dual_link = true;
+			of_node_put(remote);
+		}
+	}
+
+	dev_dbg(thc63->dev, "operating in %s-link mode\n",
+		thc63->timings.dual_link ? "dual" : "single");
+
 	return 0;
 }
 
@@ -188,6 +219,7 @@  static int thc63_probe(struct platform_device *pdev)
 	thc63->bridge.driver_private = thc63;
 	thc63->bridge.of_node = pdev->dev.of_node;
 	thc63->bridge.funcs = &thc63_bridge_func;
+	thc63->bridge.timings = &thc63->timings;
 
 	drm_bridge_add(&thc63->bridge);