[v4,1/7] clk: bcm2835: remove pllb
diff mbox series

Message ID 20190612182500.4097-2-nsaenzjulienne@suse.de
State New, archived
Delegated to: viresh kumar
Headers show
Series
  • cpufreq support for Raspberry Pi
Related show

Commit Message

Nicolas Saenz Julienne June 12, 2019, 6:24 p.m. UTC
Raspberry Pi's firmware controls this pll, we should use the firmware
interface to access it.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Eric Anholt <eric@anholt.net>
---

Changes since v1:
  - Add comment to explain why pllb isn't there anymore

 drivers/clk/bcm/clk-bcm2835.c | 28 ++++------------------------
 1 file changed, 4 insertions(+), 24 deletions(-)

Comments

Stephen Boyd June 25, 2019, 11:04 p.m. UTC | #1
Quoting Nicolas Saenz Julienne (2019-06-12 11:24:53)
> Raspberry Pi's firmware controls this pll, we should use the firmware
> interface to access it.
> 
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
> Acked-by: Eric Anholt <eric@anholt.net>
> ---

Applied to clk-next

Patch
diff mbox series

diff --git a/drivers/clk/bcm/clk-bcm2835.c b/drivers/clk/bcm/clk-bcm2835.c
index 770bb01f523e..867ae3c20041 100644
--- a/drivers/clk/bcm/clk-bcm2835.c
+++ b/drivers/clk/bcm/clk-bcm2835.c
@@ -1651,30 +1651,10 @@  static const struct bcm2835_clk_desc clk_desc_array[] = {
 		.fixed_divider = 1,
 		.flags = CLK_SET_RATE_PARENT),
 
-	/* PLLB is used for the ARM's clock. */
-	[BCM2835_PLLB]		= REGISTER_PLL(
-		.name = "pllb",
-		.cm_ctrl_reg = CM_PLLB,
-		.a2w_ctrl_reg = A2W_PLLB_CTRL,
-		.frac_reg = A2W_PLLB_FRAC,
-		.ana_reg_base = A2W_PLLB_ANA0,
-		.reference_enable_mask = A2W_XOSC_CTRL_PLLB_ENABLE,
-		.lock_mask = CM_LOCK_FLOCKB,
-
-		.ana = &bcm2835_ana_default,
-
-		.min_rate = 600000000u,
-		.max_rate = 3000000000u,
-		.max_fb_rate = BCM2835_MAX_FB_RATE),
-	[BCM2835_PLLB_ARM]	= REGISTER_PLL_DIV(
-		.name = "pllb_arm",
-		.source_pll = "pllb",
-		.cm_reg = CM_PLLB,
-		.a2w_reg = A2W_PLLB_ARM,
-		.load_mask = CM_PLLB_LOADARM,
-		.hold_mask = CM_PLLB_HOLDARM,
-		.fixed_divider = 1,
-		.flags = CLK_SET_RATE_PARENT),
+	/*
+	 * PLLB is used for the ARM's clock. Controlled by firmware, see
+	 * clk-raspberrypi.c.
+	 */
 
 	/*
 	 * PLLC is the core PLL, used to drive the core VPU clock.