diff mbox series

[1/2] mmc: mediatek: fix SDIO IRQ interrupt handle flow

Message ID 1560489970-30467-1-git-send-email-jjian.zhou@mediatek.com (mailing list archive)
State New, archived
Headers show
Series [1/2] mmc: mediatek: fix SDIO IRQ interrupt handle flow | expand

Commit Message

Jjian Zhou June 14, 2019, 5:26 a.m. UTC 
From: jjian zhou <jjian.zhou@mediatek.com>

SDIO IRQ is triggered by low level. It need disable SDIO IRQ
detected function. Otherwise the interrupt register can't be cleared.
It will process the interrupt more.

Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)

--
1.9.1

Comments

Ulf Hansson June 14, 2019, 9:46 a.m. UTC | #1 
On Fri, 14 Jun 2019 at 07:26, Jjian Zhou <jjian.zhou@mediatek.com> wrote:
>
> From: jjian zhou <jjian.zhou@mediatek.com>
>
> SDIO IRQ is triggered by low level. It need disable SDIO IRQ
> detected function. Otherwise the interrupt register can't be cleared.
> It will process the interrupt more.
>
> Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
> Signed-off-by: Yong Mao <yong.mao@mediatek.com>
> ---
>  drivers/mmc/host/mtk-sd.c | 13 +++++++------
>  1 file changed, 7 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
> index c518cc2..29992ae 100644
> --- a/drivers/mmc/host/mtk-sd.c
> +++ b/drivers/mmc/host/mtk-sd.c
> @@ -1389,10 +1389,12 @@ static void __msdc_enable_sdio_irq(struct mmc_host *mmc, int enb)
>         struct msdc_host *host = mmc_priv(mmc);
>
>         spin_lock_irqsave(&host->lock, flags);
> -       if (enb)
> +       if (enb) {
>                 sdr_set_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
> -       else
> +               sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> +       } else {
>                 sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);

Rather than clearing SDC_CFG_SDIOIDE in the irq handler, you need to
do it here. As otherwise when the mmc core calls
host->ops->enable_sdio_irq() to disable the SDIO IRQ, it may stay
enabled.

> +       }
>         spin_unlock_irqrestore(&host->lock, flags);
>  }
>
> @@ -1422,6 +1424,8 @@ static irqreturn_t msdc_irq(int irq, void *dev_id)
>                 spin_lock_irqsave(&host->lock, flags);
>                 events = readl(host->base + MSDC_INT);
>                 event_mask = readl(host->base + MSDC_INTEN);
> +               if ((events & event_mask) & MSDC_INT_SDIOIRQ)
> +                       sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);

As stated above, I suggest you move this into __msdc_enable_sdio_irq()
and thus call that function from here instead. Well, that doesn't work
as is, because of the spin lock, so you rather need to make a
sub-function of __msdc_enable_sdio_irq, that don't take/releases the
lock.

I hope that was clear. If not, I can post a patch to show you what I mean.


>                 /* clear interrupts */
>                 writel(events & event_mask, host->base + MSDC_INT);
>
> @@ -1572,10 +1576,7 @@ static void msdc_init_hw(struct msdc_host *host)
>         sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIO);
>
>         /* Config SDIO device detect interrupt function */
> -       if (host->mmc->caps & MMC_CAP_SDIO_IRQ)
> -               sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> -       else
> -               sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> +       sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
>
>         /* Configure to default data timeout */
>         sdr_set_field(host->base + SDC_CFG, SDC_CFG_DTOC, 3);
> --
> 1.9.1
>

Kind regards
Uffe
Jjian Zhou June 17, 2019, 5:57 a.m. UTC | #2 
On Fri, 2019-06-14 at 17:46 +0800, Ulf Hansson wrote:
> On Fri, 14 Jun 2019 at 07:26, Jjian Zhou <jjian.zhou@mediatek.com> wrote:
> >
> > From: jjian zhou <jjian.zhou@mediatek.com>
> >
> > SDIO IRQ is triggered by low level. It need disable SDIO IRQ
> > detected function. Otherwise the interrupt register can't be cleared.
> > It will process the interrupt more.
> >
> > Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
> > Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
> > Signed-off-by: Yong Mao <yong.mao@mediatek.com>
> > ---
> >  drivers/mmc/host/mtk-sd.c | 13 +++++++------
> >  1 file changed, 7 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
> > index c518cc2..29992ae 100644
> > --- a/drivers/mmc/host/mtk-sd.c
> > +++ b/drivers/mmc/host/mtk-sd.c
> > @@ -1389,10 +1389,12 @@ static void __msdc_enable_sdio_irq(struct mmc_host *mmc, int enb)
> >         struct msdc_host *host = mmc_priv(mmc);
> >
> >         spin_lock_irqsave(&host->lock, flags);
> > -       if (enb)
> > +       if (enb) {
> >                 sdr_set_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
> > -       else
> > +               sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> > +       } else {
> >                 sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
> 
> Rather than clearing SDC_CFG_SDIOIDE in the irq handler, you need to
> do it here. As otherwise when the mmc core calls
> host->ops->enable_sdio_irq() to disable the SDIO IRQ, it may stay
> enabled.
> 

Thank you for your review.

I remove the spin lock in "__msdc_enable_sdio_irq" and add 
spin lock in "msdc_enable_sdio_irq". The modification of
"__msdc_enable_sdio_irq" and "msdc_enable_sdio_irq" is as following.

static void __msdc_enable_sdio_irq(struct msdc_host *host, int enb)
{
	if (enb) {
		sdr_set_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
		sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
	} else {
		sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
		sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
	}
}

static void msdc_enable_sdio_irq(struct mmc_host *mmc, int enb)
{
	unsigned long flags;
	struct msdc_host *host = mmc_priv(mmc);
	spin_lock_irqsave(&host->lock, flags);;
	__msdc_enable_sdio_irq(host, enb);
	spin_unlock_irqrestore(&host->lock, flags);

	if (enb)
		pm_runtime_get_noresume(host->dev);
	else
		pm_runtime_get_noidle(host->dev);
}

> > +       }
> >         spin_unlock_irqrestore(&host->lock, flags);
> >  }
> >
> > @@ -1422,6 +1424,8 @@ static irqreturn_t msdc_irq(int irq, void *dev_id)
> >                 spin_lock_irqsave(&host->lock, flags);
> >                 events = readl(host->base + MSDC_INT);
> >                 event_mask = readl(host->base + MSDC_INTEN);
> > +               if ((events & event_mask) & MSDC_INT_SDIOIRQ)
> > +                       sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> 
> As stated above, I suggest you move this into __msdc_enable_sdio_irq()
> and thus call that function from here instead. Well, that doesn't work
> as is, because of the spin lock, so you rather need to make a
> sub-function of __msdc_enable_sdio_irq, that don't take/releases the
> lock.
> 
> I hope that was clear. If not, I can post a patch to show you what I mean.
> 

I also modify this part handler in msdc_irq.

	spin_lock_irqsave(&host->lock, flags);
	events = readl(host->base + MSDC_INT);
	event_mask = readl(host->base + MSDC_INTEN);
	if ((events & event_mask) & MSDC_INT_SDIOIRQ)
		__msdc_enable_sdio_irq(host, 0);
	/* clear interrupts */
	writel(events & event_mask, host->base + MSDC_INT);

	mrq = host->mrq;
	cmd = host->cmd;
	data = host->data;
	spin_unlock_irqrestore(&host->lock, flags);

	if ((events & event_mask) & MSDC_INT_SDIOIRQ)
		sdio_signal_irq(host->mmc);

I also will add spin lock in the "msdc_ack_sdio_irq".

Looking forward to your suggestions.
> 
> >                 /* clear interrupts */
> >                 writel(events & event_mask, host->base + MSDC_INT);
> >
> > @@ -1572,10 +1576,7 @@ static void msdc_init_hw(struct msdc_host *host)
> >         sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIO);
> >
> >         /* Config SDIO device detect interrupt function */
> > -       if (host->mmc->caps & MMC_CAP_SDIO_IRQ)
> > -               sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> > -       else
> > -               sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> > +       sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> >
> >         /* Configure to default data timeout */
> >         sdr_set_field(host->base + SDC_CFG, SDC_CFG_DTOC, 3);
> > --
> > 1.9.1
> >
> 
> Kind regards
> Uffe
Ulf Hansson June 17, 2019, 7:47 a.m. UTC | #3 
On Mon, 17 Jun 2019 at 07:57, jjian zhou <jjian.zhou@mediatek.com> wrote:
>
> On Fri, 2019-06-14 at 17:46 +0800, Ulf Hansson wrote:
> > On Fri, 14 Jun 2019 at 07:26, Jjian Zhou <jjian.zhou@mediatek.com> wrote:
> > >
> > > From: jjian zhou <jjian.zhou@mediatek.com>
> > >
> > > SDIO IRQ is triggered by low level. It need disable SDIO IRQ
> > > detected function. Otherwise the interrupt register can't be cleared.
> > > It will process the interrupt more.
> > >
> > > Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
> > > Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
> > > Signed-off-by: Yong Mao <yong.mao@mediatek.com>
> > > ---
> > >  drivers/mmc/host/mtk-sd.c | 13 +++++++------
> > >  1 file changed, 7 insertions(+), 6 deletions(-)
> > >
> > > diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
> > > index c518cc2..29992ae 100644
> > > --- a/drivers/mmc/host/mtk-sd.c
> > > +++ b/drivers/mmc/host/mtk-sd.c
> > > @@ -1389,10 +1389,12 @@ static void __msdc_enable_sdio_irq(struct mmc_host *mmc, int enb)
> > >         struct msdc_host *host = mmc_priv(mmc);
> > >
> > >         spin_lock_irqsave(&host->lock, flags);
> > > -       if (enb)
> > > +       if (enb) {
> > >                 sdr_set_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
> > > -       else
> > > +               sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> > > +       } else {
> > >                 sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
> >
> > Rather than clearing SDC_CFG_SDIOIDE in the irq handler, you need to
> > do it here. As otherwise when the mmc core calls
> > host->ops->enable_sdio_irq() to disable the SDIO IRQ, it may stay
> > enabled.
> >
>
> Thank you for your review.
>
> I remove the spin lock in "__msdc_enable_sdio_irq" and add
> spin lock in "msdc_enable_sdio_irq". The modification of
> "__msdc_enable_sdio_irq" and "msdc_enable_sdio_irq" is as following.
>
> static void __msdc_enable_sdio_irq(struct msdc_host *host, int enb)
> {
>         if (enb) {
>                 sdr_set_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
>                 sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
>         } else {
>                 sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
>                 sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
>         }
> }
>
> static void msdc_enable_sdio_irq(struct mmc_host *mmc, int enb)
> {
>         unsigned long flags;
>         struct msdc_host *host = mmc_priv(mmc);
>         spin_lock_irqsave(&host->lock, flags);;
>         __msdc_enable_sdio_irq(host, enb);
>         spin_unlock_irqrestore(&host->lock, flags);
>
>         if (enb)
>                 pm_runtime_get_noresume(host->dev);
>         else
>                 pm_runtime_get_noidle(host->dev);
> }
>
> > > +       }
> > >         spin_unlock_irqrestore(&host->lock, flags);
> > >  }
> > >
> > > @@ -1422,6 +1424,8 @@ static irqreturn_t msdc_irq(int irq, void *dev_id)
> > >                 spin_lock_irqsave(&host->lock, flags);
> > >                 events = readl(host->base + MSDC_INT);
> > >                 event_mask = readl(host->base + MSDC_INTEN);
> > > +               if ((events & event_mask) & MSDC_INT_SDIOIRQ)
> > > +                       sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
> >
> > As stated above, I suggest you move this into __msdc_enable_sdio_irq()
> > and thus call that function from here instead. Well, that doesn't work
> > as is, because of the spin lock, so you rather need to make a
> > sub-function of __msdc_enable_sdio_irq, that don't take/releases the
> > lock.
> >
> > I hope that was clear. If not, I can post a patch to show you what I mean.
> >
>
> I also modify this part handler in msdc_irq.
>
>         spin_lock_irqsave(&host->lock, flags);
>         events = readl(host->base + MSDC_INT);
>         event_mask = readl(host->base + MSDC_INTEN);
>         if ((events & event_mask) & MSDC_INT_SDIOIRQ)
>                 __msdc_enable_sdio_irq(host, 0);
>         /* clear interrupts */
>         writel(events & event_mask, host->base + MSDC_INT);
>
>         mrq = host->mrq;
>         cmd = host->cmd;
>         data = host->data;
>         spin_unlock_irqrestore(&host->lock, flags);
>
>         if ((events & event_mask) & MSDC_INT_SDIOIRQ)
>                 sdio_signal_irq(host->mmc);
>
> I also will add spin lock in the "msdc_ack_sdio_irq".
>
> Looking forward to your suggestions.

Seems reasonable, please post a new version, then I will review again.

[...]

Kind regards
Uffe
diff mbox series

Patch

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index c518cc2..29992ae 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -1389,10 +1389,12 @@  static void __msdc_enable_sdio_irq(struct mmc_host *mmc, int enb)
 	struct msdc_host *host = mmc_priv(mmc);

 	spin_lock_irqsave(&host->lock, flags);
-	if (enb)
+	if (enb) {
 		sdr_set_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
-	else
+		sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
+	} else {
 		sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INTEN_SDIOIRQ);
+	}
 	spin_unlock_irqrestore(&host->lock, flags);
 }

@@ -1422,6 +1424,8 @@  static irqreturn_t msdc_irq(int irq, void *dev_id)
 		spin_lock_irqsave(&host->lock, flags);
 		events = readl(host->base + MSDC_INT);
 		event_mask = readl(host->base + MSDC_INTEN);
+		if ((events & event_mask) & MSDC_INT_SDIOIRQ)
+			sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
 		/* clear interrupts */
 		writel(events & event_mask, host->base + MSDC_INT);

@@ -1572,10 +1576,7 @@  static void msdc_init_hw(struct msdc_host *host)
 	sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIO);

 	/* Config SDIO device detect interrupt function */
-	if (host->mmc->caps & MMC_CAP_SDIO_IRQ)
-		sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
-	else
-		sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);
+	sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_SDIOIDE);

 	/* Configure to default data timeout */
 	sdr_set_field(host->base + SDC_CFG, SDC_CFG_DTOC, 3);