| Message ID | 1560779277-32465-1-git-send-email-hugues.fruchet@st.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | media: ov5640: add support of V4L2_CID_LINK_FREQ | expand |
On 6/17/19 3:47 PM, Hugues Fruchet wrote: > Add support of V4L2_CID_LINK_FREQ, this is needed > by some CSI-2 receivers. > > 384MHz is exposed for the time being, corresponding > to 96MHz pixel clock with 2 bytes per pixel on 2 data lanes. > > This setup has been tested successfully with ST MIPID02 > CSI-2 to parallel bridge. > > Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> > --- > drivers/media/i2c/ov5640.c | 10 ++++++++++ > 1 file changed, 10 insertions(+) > > diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c > index 82d4ce9..79f8383 100644 > --- a/drivers/media/i2c/ov5640.c > +++ b/drivers/media/i2c/ov5640.c > @@ -218,6 +218,7 @@ struct ov5640_ctrls { > struct v4l2_ctrl *test_pattern; > struct v4l2_ctrl *hflip; > struct v4l2_ctrl *vflip; > + struct v4l2_ctrl *link_freq; > }; > > struct ov5640_dev { > @@ -2198,6 +2199,10 @@ static int ov5640_try_fmt_internal(struct v4l2_subdev *sd, > return 0; > } > > +static const s64 link_freq_menu_items[] = { > + 384000000, > +}; > + > static int ov5640_set_fmt(struct v4l2_subdev *sd, > struct v4l2_subdev_pad_config *cfg, > struct v4l2_subdev_format *format) > @@ -2703,6 +2708,11 @@ static int ov5640_init_controls(struct ov5640_dev *sensor) > V4L2_CID_POWER_LINE_FREQUENCY_AUTO, 0, > V4L2_CID_POWER_LINE_FREQUENCY_50HZ); > > + ctrls->link_freq = v4l2_ctrl_new_int_menu(hdl, ops, V4L2_CID_LINK_FREQ, > + 0, 0, link_freq_menu_items); > + if (ctrls->link_freq) > + ctrls->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; I'd drop this. It's fine to set it, there is only one value here, so that's effectively a NOP. I see more drivers that set this flag, even though it is not necessary. The problem is that some application might assume this control can be set, and then fails because this returns an error. You do need to add an entry to ov5640_s_ctrl: case V4L2_CID_LINK_FREQ: return 0; Regards, Hans > + > if (hdl->error) { > ret = hdl->error; > goto free_ctrls; >
diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c index 82d4ce9..79f8383 100644 --- a/drivers/media/i2c/ov5640.c +++ b/drivers/media/i2c/ov5640.c @@ -218,6 +218,7 @@ struct ov5640_ctrls { struct v4l2_ctrl *test_pattern; struct v4l2_ctrl *hflip; struct v4l2_ctrl *vflip; + struct v4l2_ctrl *link_freq; }; struct ov5640_dev { @@ -2198,6 +2199,10 @@ static int ov5640_try_fmt_internal(struct v4l2_subdev *sd, return 0; } +static const s64 link_freq_menu_items[] = { + 384000000, +}; + static int ov5640_set_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_pad_config *cfg, struct v4l2_subdev_format *format) @@ -2703,6 +2708,11 @@ static int ov5640_init_controls(struct ov5640_dev *sensor) V4L2_CID_POWER_LINE_FREQUENCY_AUTO, 0, V4L2_CID_POWER_LINE_FREQUENCY_50HZ); + ctrls->link_freq = v4l2_ctrl_new_int_menu(hdl, ops, V4L2_CID_LINK_FREQ, + 0, 0, link_freq_menu_items); + if (ctrls->link_freq) + ctrls->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; + if (hdl->error) { ret = hdl->error; goto free_ctrls;
Add support of V4L2_CID_LINK_FREQ, this is needed by some CSI-2 receivers. 384MHz is exposed for the time being, corresponding to 96MHz pixel clock with 2 bytes per pixel on 2 data lanes. This setup has been tested successfully with ST MIPID02 CSI-2 to parallel bridge. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> --- drivers/media/i2c/ov5640.c | 10 ++++++++++ 1 file changed, 10 insertions(+)