| Message ID | 20190703190910.32633-11-helen.koike@collabora.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v7,01/14] media: videodev2.h, v4l2-ioctl: add rkisp1 meta buffer format | expand |
Hello Helen, On 7/3/19 4:09 PM, Helen Koike wrote: > From: Jacob Chen <jacob2.chen@rock-chips.com> > > Add DT bindings documentation for Rockchip ISP1 > > Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com> > Reviewed-by: Rob Herring <robh@kernel.org> > [update for upstream] > Signed-off-by: Helen Koike <helen.koike@collabora.com> > > --- > > Changes in v7: > - update document with new design and tested example > > .../bindings/media/rockchip-isp1.txt | 71 +++++++++++++++++++ > 1 file changed, 71 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/rockchip-isp1.txt > > diff --git a/Documentation/devicetree/bindings/media/rockchip-isp1.txt b/Documentation/devicetree/bindings/media/rockchip-isp1.txt > new file mode 100644 > index 000000000000..a97fef0f189f > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/rockchip-isp1.txt > @@ -0,0 +1,71 @@ > +Rockchip SoC Image Signal Processing unit v1 > +---------------------------------------------- > + > +Rockchip ISP1 is the Camera interface for the Rockchip series of SoCs > +which contains image processing, scaling, and compression funcitons. > + > +Required properties: > +- compatible: value should be one of the following > + "rockchip,rk3288-cif-isp"; > + "rockchip,rk3399-cif-isp"; > +- reg : offset and length of the register set for the device. > +- interrupts: should contain ISP interrupt. > +- clocks: phandle to the required clocks. > +- clock-names: required clock name. > +- iommus: required a iommu node. > +- phys: the phandle for the PHY port > +- phy-names: must contain "dphy" > + > +port node > +------------------- I would remove those extra `---`, and keep as: ...node ...---- The same applies for the title. Thanks, André > + > +The device node should contain one 'ports' child node, with children 'port' > +with child 'endpoint'. > +nodes, according to the bindings defined in Documentation/devicetree/bindings/ > +media/video-interfaces.txt. > + > +- endpoint(mipi): > + - remote-endpoint: Connecting to Rockchip MIPI-DPHY, > + which is defined in rockchip-mipi-dphy.txt. > + > +The port node must contain at least one endpoint, either parallel or mipi. > +It could have multiple endpoints, but please note the hardware don't support > +two sensors work at a time, they are supposed to work asynchronously. > + > +Device node example > +------------------- > + > + isp0: isp0@ff910000 { > + compatible = "rockchip,rk3399-cif-isp"; > + reg = <0x0 0xff910000 0x0 0x4000>; > + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&cru SCLK_ISP0>, > + <&cru ACLK_ISP0>, <&cru ACLK_ISP0_WRAPPER>, > + <&cru HCLK_ISP0>, <&cru HCLK_ISP0_WRAPPER>; > + clock-names = "clk_isp", > + "aclk_isp", "aclk_isp_wrap", > + "hclk_isp", "hclk_isp_wrap"; > + power-domains = <&power RK3399_PD_ISP0>; > + iommus = <&isp0_mmu>; > + phys = <&dphy>; > + phy-names = "dphy"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + mipi_in_wcam: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&wcam_out>; > + data-lanes = <1 2>; > + }; > + > + mipi_in_ucam: endpoint@1 { > + reg = <1>; > + remote-endpoint = <&ucam_out>; > + data-lanes = <1>; > + }; > + }; > + }; > + };
diff --git a/Documentation/devicetree/bindings/media/rockchip-isp1.txt b/Documentation/devicetree/bindings/media/rockchip-isp1.txt new file mode 100644 index 000000000000..a97fef0f189f --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip-isp1.txt @@ -0,0 +1,71 @@ +Rockchip SoC Image Signal Processing unit v1 +---------------------------------------------- + +Rockchip ISP1 is the Camera interface for the Rockchip series of SoCs +which contains image processing, scaling, and compression funcitons. + +Required properties: +- compatible: value should be one of the following + "rockchip,rk3288-cif-isp"; + "rockchip,rk3399-cif-isp"; +- reg : offset and length of the register set for the device. +- interrupts: should contain ISP interrupt. +- clocks: phandle to the required clocks. +- clock-names: required clock name. +- iommus: required a iommu node. +- phys: the phandle for the PHY port +- phy-names: must contain "dphy" + +port node +------------------- + +The device node should contain one 'ports' child node, with children 'port' +with child 'endpoint'. +nodes, according to the bindings defined in Documentation/devicetree/bindings/ +media/video-interfaces.txt. + +- endpoint(mipi): + - remote-endpoint: Connecting to Rockchip MIPI-DPHY, + which is defined in rockchip-mipi-dphy.txt. + +The port node must contain at least one endpoint, either parallel or mipi. +It could have multiple endpoints, but please note the hardware don't support +two sensors work at a time, they are supposed to work asynchronously. + +Device node example +------------------- + + isp0: isp0@ff910000 { + compatible = "rockchip,rk3399-cif-isp"; + reg = <0x0 0xff910000 0x0 0x4000>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&cru SCLK_ISP0>, + <&cru ACLK_ISP0>, <&cru ACLK_ISP0_WRAPPER>, + <&cru HCLK_ISP0>, <&cru HCLK_ISP0_WRAPPER>; + clock-names = "clk_isp", + "aclk_isp", "aclk_isp_wrap", + "hclk_isp", "hclk_isp_wrap"; + power-domains = <&power RK3399_PD_ISP0>; + iommus = <&isp0_mmu>; + phys = <&dphy>; + phy-names = "dphy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + mipi_in_wcam: endpoint@0 { + reg = <0>; + remote-endpoint = <&wcam_out>; + data-lanes = <1 2>; + }; + + mipi_in_ucam: endpoint@1 { + reg = <1>; + remote-endpoint = <&ucam_out>; + data-lanes = <1>; + }; + }; + }; + };