diff mbox series

[6/6] arm64: dts: allwinner: h6: Add PWM node

Message ID 20190726184045.14669-7-jernej.skrabec@siol.net (mailing list archive)
State New, archived
Headers show
Series pwm: sun4i: Add support for Allwinner H6 | expand

Commit Message

Jernej Škrabec July 26, 2019, 6:40 p.m. UTC
Allwinner H6 PWM is similar to that in A20 except that it has additional
bus clock and reset line.

Note that first PWM channel is connected to output pin and second
channel is used internally, as a clock source to AC200 co-packaged chip.
This means that any combination of these two channels can be used and
thus it doesn't make sense to add pinctrl nodes at this point.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

Comments

Maxime Ripard July 27, 2019, 10:51 a.m. UTC | #1
On Fri, Jul 26, 2019 at 08:40:45PM +0200, Jernej Skrabec wrote:
> Allwinner H6 PWM is similar to that in A20 except that it has additional
> bus clock and reset line.
>
> Note that first PWM channel is connected to output pin and second
> channel is used internally, as a clock source to AC200 co-packaged chip.
> This means that any combination of these two channels can be used and
> thus it doesn't make sense to add pinctrl nodes at this point.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> ---
>  arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 10 ++++++++++
>  1 file changed, 10 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> index e8bed58e7246..c1abd805cfdc 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> @@ -229,6 +229,16 @@
>  			status = "disabled";
>  		};
>
> +		pwm: pwm@300a000 {
> +			compatible = "allwinner,sun50i-h6-pwm";
> +			reg = <0x0300a000 0x400>;
> +			clocks = <&osc24M>, <&ccu CLK_BUS_PWM>;
> +			clock-names = "pwm", "bus";

We always have the bus clock first, so I'd really like to keep
that. We also usually use mod for the second clock, and not the name
of the device itself.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index e8bed58e7246..c1abd805cfdc 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -229,6 +229,16 @@ 
 			status = "disabled";
 		};
 
+		pwm: pwm@300a000 {
+			compatible = "allwinner,sun50i-h6-pwm";
+			reg = <0x0300a000 0x400>;
+			clocks = <&osc24M>, <&ccu CLK_BUS_PWM>;
+			clock-names = "pwm", "bus";
+			resets = <&ccu RST_BUS_PWM>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		pio: pinctrl@300b000 {
 			compatible = "allwinner,sun50i-h6-pinctrl";
 			reg = <0x0300b000 0x400>;