[2/2] max9286: Add MAX9286 driver
diff mbox series

Message ID 20190809040558.10698-3-niklas.soderlund+renesas@ragnatech.se
State New
Delegated to: Kieran Bingham
Headers show
Series
  • max9286: Add MAX9286 driver with single camera support
Related show

Commit Message

Niklas Söderlund Aug. 9, 2019, 4:05 a.m. UTC
The MAX9286 is a 4-channel GMSL deserializer with coax or STP input and
CSI-2 output. The device supports multicamera streaming applications,
and features the ability to synchronise the attached cameras. The
driver however limits the number of cameras to one as there are no way
to express in V4L2 today that multiple video streams are transmitted
over one CSI-2 bus.

CSI-2 output can be configured with 1 to 4 lanes, and a control channel
is supported over I2C, which implements an I2C mux to facilitate
communications with connected cameras across the reverse control
channel.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
---
 MAINTAINERS                 |   10 +
 drivers/media/i2c/Kconfig   |   11 +
 drivers/media/i2c/Makefile  |    1 +
 drivers/media/i2c/max9286.c | 1081 +++++++++++++++++++++++++++++++++++
 4 files changed, 1103 insertions(+)
 create mode 100644 drivers/media/i2c/max9286.c

Comments

Kieran Bingham Aug. 9, 2019, 8:09 a.m. UTC | #1
Hi Niklas,

This should be at least v5.

Did you take the last v4 and work from there?
I have made changes since the last posting. Did you get an update from
my branches?

What changes have you made to this posting compared to whichever
patch-base you have taken to start from?

--
Kieran



On 09/08/2019 05:05, Niklas Söderlund wrote:
> The MAX9286 is a 4-channel GMSL deserializer with coax or STP input and
> CSI-2 output. The device supports multicamera streaming applications,
> and features the ability to synchronise the attached cameras. The
> driver however limits the number of cameras to one as there are no way
> to express in V4L2 today that multiple video streams are transmitted
> over one CSI-2 bus.
> 
> CSI-2 output can be configured with 1 to 4 lanes, and a control channel
> is supported over I2C, which implements an I2C mux to facilitate
> communications with connected cameras across the reverse control
> channel.
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> ---
>  MAINTAINERS                 |   10 +
>  drivers/media/i2c/Kconfig   |   11 +
>  drivers/media/i2c/Makefile  |    1 +
>  drivers/media/i2c/max9286.c | 1081 +++++++++++++++++++++++++++++++++++
>  4 files changed, 1103 insertions(+)
>  create mode 100644 drivers/media/i2c/max9286.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 6426db5198f05377..f8f028811feee489 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -9746,6 +9746,16 @@ F:	Documentation/devicetree/bindings/hwmon/max6697.txt
>  F:	drivers/hwmon/max6697.c
>  F:	include/linux/platform_data/max6697.h
>  
> +MAX9286 QUAD GMSL DESERIALIZER DRIVER
> +M:	Jacopo Mondi <jacopo+renesas@jmondi.org>
> +M:	Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
> +M:	Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> +M:	Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> +L:	linux-media@vger.kernel.org
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/media/i2c/maxim,max9286.txt
> +F:	drivers/media/i2c/max9286.c
> +
>  MAX9860 MONO AUDIO VOICE CODEC DRIVER
>  M:	Peter Rosin <peda@axentia.se>
>  L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index 79ce9ec6fc1be1e6..c20b151a16e64349 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -439,6 +439,17 @@ config VIDEO_VPX3220
>  	  To compile this driver as a module, choose M here: the
>  	  module will be called vpx3220.
>  
> +config VIDEO_MAX9286
> +	tristate "Maxim MAX9286 GMSL deserializer support"
> +	depends on I2C && I2C_MUX
> +	depends on VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER
> +	select V4L2_FWNODE
> +	help
> +	  This driver supports the Maxim MAX9286 GMSL deserializer.
> +
> +	  To compile this driver as a module, choose M here: the
> +	  module will be called max9286.
> +
>  comment "Video and audio decoders"
>  
>  config VIDEO_SAA717X
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index fd4ea86dedd5df44..25b3c7e5becfa714 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -114,5 +114,6 @@ obj-$(CONFIG_VIDEO_IMX274)	+= imx274.o
>  obj-$(CONFIG_VIDEO_IMX319)	+= imx319.o
>  obj-$(CONFIG_VIDEO_IMX355)	+= imx355.o
>  obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o
> +obj-$(CONFIG_VIDEO_MAX9286)	+= max9286.o
>  
>  obj-$(CONFIG_SDR_MAX2175) += max2175.o
> diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c
> new file mode 100644
> index 0000000000000000..debd11ac269d28ca
> --- /dev/null
> +++ b/drivers/media/i2c/max9286.c
> @@ -0,0 +1,1081 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Maxim MAX9286 GMSL Deserializer Driver
> + *
> + * Copyright (C) 2017-2018 Jacopo Mondi
> + * Copyright (C) 2017-2018 Kieran Bingham
> + * Copyright (C) 2017-2018 Laurent Pinchart
> + * Copyright (C) 2017-2018 Niklas Söderlund
> + * Copyright (C) 2016 Renesas Electronics Corporation
> + * Copyright (C) 2015 Cogent Embedded, Inc.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/fwnode.h>
> +#include <linux/i2c.h>
> +#include <linux/i2c-mux.h>
> +#include <linux/module.h>
> +#include <linux/of_graph.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/slab.h>
> +
> +#include <media/v4l2-async.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-fwnode.h>
> +#include <media/v4l2-subdev.h>
> +
> +/* Register 0x00 */
> +#define MAX9286_MSTLINKSEL_AUTO		(7 << 5)
> +#define MAX9286_MSTLINKSEL(n)		((n) << 5)
> +#define MAX9286_EN_VS_GEN		BIT(4)
> +#define MAX9286_LINKEN(n)		(1 << (n))
> +/* Register 0x01 */
> +#define MAX9286_FSYNCMODE_ECU		(3 << 6)
> +#define MAX9286_FSYNCMODE_EXT		(2 << 6)
> +#define MAX9286_FSYNCMODE_INT_OUT	(1 << 6)
> +#define MAX9286_FSYNCMODE_INT_HIZ	(0 << 6)
> +#define MAX9286_GPIEN			BIT(5)
> +#define MAX9286_ENLMO_RSTFSYNC		BIT(2)
> +#define MAX9286_FSYNCMETH_AUTO		(2 << 0)
> +#define MAX9286_FSYNCMETH_SEMI_AUTO	(1 << 0)
> +#define MAX9286_FSYNCMETH_MANUAL	(0 << 0)
> +#define MAX9286_REG_FSYNC_PERIOD_L	0x06
> +#define MAX9286_REG_FSYNC_PERIOD_M	0x07
> +#define MAX9286_REG_FSYNC_PERIOD_H	0x08
> +/* Register 0x0a */
> +#define MAX9286_FWDCCEN(n)		(1 << ((n) + 4))
> +#define MAX9286_REVCCEN(n)		(1 << (n))
> +/* Register 0x0c */
> +#define MAX9286_HVEN			BIT(7)
> +#define MAX9286_EDC_6BIT_HAMMING	(2 << 5)
> +#define MAX9286_EDC_6BIT_CRC		(1 << 5)
> +#define MAX9286_EDC_1BIT_PARITY		(0 << 5)
> +#define MAX9286_DESEL			BIT(4)
> +#define MAX9286_INVVS			BIT(3)
> +#define MAX9286_INVHS			BIT(2)
> +#define MAX9286_HVSRC_D0		(2 << 0)
> +#define MAX9286_HVSRC_D14		(1 << 0)
> +#define MAX9286_HVSRC_D18		(0 << 0)
> +/* Register 0x12 */
> +#define MAX9286_CSILANECNT(n)		(((n) - 1) << 6)
> +#define MAX9286_CSIDBL			BIT(5)
> +#define MAX9286_DBL			BIT(4)
> +#define MAX9286_DATATYPE_USER_8BIT	(11 << 0)
> +#define MAX9286_DATATYPE_USER_YUV_12BIT	(10 << 0)
> +#define MAX9286_DATATYPE_USER_24BIT	(9 << 0)
> +#define MAX9286_DATATYPE_RAW14		(8 << 0)
> +#define MAX9286_DATATYPE_RAW11		(7 << 0)
> +#define MAX9286_DATATYPE_RAW10		(6 << 0)
> +#define MAX9286_DATATYPE_RAW8		(5 << 0)
> +#define MAX9286_DATATYPE_YUV422_10BIT	(4 << 0)
> +#define MAX9286_DATATYPE_YUV422_8BIT	(3 << 0)
> +#define MAX9286_DATATYPE_RGB555		(2 << 0)
> +#define MAX9286_DATATYPE_RGB565		(1 << 0)
> +#define MAX9286_DATATYPE_RGB888		(0 << 0)
> +/* Register 0x15 */
> +#define MAX9286_VC(n)			((n) << 5)
> +#define MAX9286_VCTYPE			BIT(4)
> +#define MAX9286_CSIOUTEN		BIT(3)
> +#define MAX9286_0X15_RESV		(3 << 0)
> +/* Register 0x1b */
> +#define MAX9286_SWITCHIN(n)		(1 << ((n) + 4))
> +#define MAX9286_ENEQ(n)			(1 << (n))
> +/* Register 0x27 */
> +#define MAX9286_LOCKED			BIT(7)
> +/* Register 0x31 */
> +#define MAX9286_FSYNC_LOCKED		BIT(6)
> +/* Register 0x34 */
> +#define MAX9286_I2CLOCACK		BIT(7)
> +#define MAX9286_I2CSLVSH_1046NS_469NS	(3 << 5)
> +#define MAX9286_I2CSLVSH_938NS_352NS	(2 << 5)
> +#define MAX9286_I2CSLVSH_469NS_234NS	(1 << 5)
> +#define MAX9286_I2CSLVSH_352NS_117NS	(0 << 5)
> +#define MAX9286_I2CMSTBT_837KBPS	(7 << 2)
> +#define MAX9286_I2CMSTBT_533KBPS	(6 << 2)
> +#define MAX9286_I2CMSTBT_339KBPS	(5 << 2)
> +#define MAX9286_I2CMSTBT_173KBPS	(4 << 2)
> +#define MAX9286_I2CMSTBT_105KBPS	(3 << 2)
> +#define MAX9286_I2CMSTBT_84KBPS		(2 << 2)
> +#define MAX9286_I2CMSTBT_28KBPS		(1 << 2)
> +#define MAX9286_I2CMSTBT_8KBPS		(0 << 2)
> +#define MAX9286_I2CSLVTO_NONE		(3 << 0)
> +#define MAX9286_I2CSLVTO_1024US		(2 << 0)
> +#define MAX9286_I2CSLVTO_256US		(1 << 0)
> +#define MAX9286_I2CSLVTO_64US		(0 << 0)
> +/* Register 0x3b */
> +#define MAX9286_REV_TRF(n)		((n) << 4)
> +#define MAX9286_REV_AMP(n)		((((n) - 30) / 10) << 1) /* in mV */
> +#define MAX9286_REV_AMP_X		BIT(0)
> +/* Register 0x3f */
> +#define MAX9286_EN_REV_CFG		BIT(6)
> +#define MAX9286_REV_FLEN(n)		((n) - 20)
> +/* Register 0x49 */
> +#define MAX9286_VIDEO_DETECT_MASK	0x0f
> +/* Register 0x69 */
> +#define MAX9286_LFLTBMONMASKED		BIT(7)
> +#define MAX9286_LOCKMONMASKED		BIT(6)
> +#define MAX9286_AUTOCOMBACKEN		BIT(5)
> +#define MAX9286_AUTOMASKEN		BIT(4)
> +#define MAX9286_MASKLINK(n)		((n) << 0)
> +
> +#define MAX9286_NUM_GMSL		4
> +#define MAX9286_N_SINKS			4
> +#define MAX9286_N_PADS			5
> +#define MAX9286_SRC_PAD			4
> +
> +#define MAXIM_I2C_I2C_SPEED_400KHZ	MAX9286_I2CMSTBT_339KBPS
> +#define MAXIM_I2C_I2C_SPEED_100KHZ	MAX9286_I2CMSTBT_105KBPS
> +#define MAXIM_I2C_SPEED			MAXIM_I2C_I2C_SPEED_100KHZ
> +
> +struct max9286_source {
> +	struct v4l2_async_subdev asd;
> +	struct v4l2_subdev *sd;
> +	struct fwnode_handle *fwnode;
> +};
> +
> +#define asd_to_max9286_source(_asd) \
> +	container_of(_asd, struct max9286_source, asd)
> +
> +struct max9286_priv {
> +	struct i2c_client *client;
> +	struct v4l2_subdev sd;
> +	struct media_pad pads[MAX9286_N_PADS];
> +	struct regulator *regulator;
> +	bool poc_enabled;
> +	int streaming;
> +
> +	struct i2c_mux_core *mux;
> +	unsigned int mux_channel;
> +
> +	struct v4l2_ctrl_handler ctrls;
> +
> +	struct v4l2_mbus_framefmt fmt[MAX9286_N_SINKS];
> +
> +	unsigned int nsources;
> +	unsigned int source_mask;
> +	unsigned int route_mask;
> +	unsigned int csi2_data_lanes;
> +	struct max9286_source sources[MAX9286_NUM_GMSL];
> +	struct v4l2_async_notifier notifier;
> +};
> +
> +static struct max9286_source *next_source(struct max9286_priv *priv,
> +					  struct max9286_source *source)
> +{
> +	if (!source)
> +		source = &priv->sources[0];
> +	else
> +		source++;
> +
> +	for (; source < &priv->sources[MAX9286_NUM_GMSL]; source++) {
> +		if (source->fwnode)
> +			return source;
> +	}
> +
> +	return NULL;
> +}
> +
> +#define for_each_source(max9286, source) \
> +	for (source = NULL; (source = next_source(max9286, source)); )
> +
> +#define to_index(max9286, source) (source - &max9286->sources[0])
> +
> +static inline struct max9286_priv *sd_to_max9286(struct v4l2_subdev *sd)
> +{
> +	return container_of(sd, struct max9286_priv, sd);
> +}
> +
> +/* -----------------------------------------------------------------------------
> + * I2C IO
> + */
> +
> +static int max9286_read(struct max9286_priv *priv, u8 reg)
> +{
> +	int ret;
> +
> +	ret = i2c_smbus_read_byte_data(priv->client, reg);
> +	if (ret < 0)
> +		dev_err(&priv->client->dev,
> +			"%s: register 0x%02x read failed (%d)\n",
> +			__func__, reg, ret);
> +
> +	return ret;
> +}
> +
> +static int max9286_write(struct max9286_priv *priv, u8 reg, u8 val)
> +{
> +	int ret;
> +
> +	ret = i2c_smbus_write_byte_data(priv->client, reg, val);
> +	if (ret < 0)
> +		dev_err(&priv->client->dev,
> +			"%s: register 0x%02x write failed (%d)\n",
> +			__func__, reg, ret);
> +
> +	return ret;
> +}
> +
> +/* -----------------------------------------------------------------------------
> + * I2C Multiplexer
> + */
> +
> +static int max9286_i2c_mux_close(struct max9286_priv *priv)
> +{
> +	/* FIXME: See note in max9286_i2c_mux_select() */
> +	if (priv->streaming)
> +		return 0;
> +	/*
> +	 * Ensure that both the forward and reverse channel are disabled on the
> +	 * mux, and that the channel ID is invalidated to ensure we reconfigure
> +	 * on the next select call.
> +	 */
> +	priv->mux_channel = -1;
> +	max9286_write(priv, 0x0a, 0x00);
> +	usleep_range(3000, 5000);
> +
> +	return 0;
> +}
> +
> +static int max9286_i2c_mux_select(struct i2c_mux_core *muxc, u32 chan)
> +{
> +	struct max9286_priv *priv = i2c_mux_priv(muxc);
> +
> +	/*
> +	 * FIXME: This state keeping is a hack and do the job. It should
> +	 * be should be reworked. One option to consider is that once all
> +	 * cameras are programmed the mux selection logic should be disabled
> +	 * and all all reverse and forward channels enable all the time.
> +	 *
> +	 * In any case this logic with a int that have two states should be
> +	 * reworked!
> +	 */
> +	if (priv->streaming == 1) {
> +		max9286_write(priv, 0x0a, 0xff);
> +		priv->streaming = 2;
> +		return 0;
> +	} else if (priv->streaming == 2) {
> +		return 0;
> +	}
> +
> +	if (priv->mux_channel == chan)
> +		return 0;
> +
> +	priv->mux_channel = chan;
> +
> +	max9286_write(priv, 0x0a,
> +		      MAX9286_FWDCCEN(chan) | MAX9286_REVCCEN(chan));
> +
> +	/*
> +	 * We must sleep after any change to the forward or reverse channel
> +	 * configuration.
> +	 */
> +	usleep_range(3000, 5000);
> +
> +	return 0;
> +}
> +
> +static int max9286_i2c_mux_init(struct max9286_priv *priv)
> +{
> +	struct max9286_source *source;
> +	int ret;
> +
> +	if (!i2c_check_functionality(priv->client->adapter,
> +				     I2C_FUNC_SMBUS_WRITE_BYTE_DATA))
> +		return -ENODEV;
> +
> +	priv->mux = i2c_mux_alloc(priv->client->adapter, &priv->client->dev,
> +				 priv->nsources, 0, I2C_MUX_LOCKED,
> +				 max9286_i2c_mux_select, NULL);
> +	if (!priv->mux)
> +		return -ENOMEM;
> +
> +	priv->mux->priv = priv;
> +
> +	for_each_source(priv, source) {
> +		unsigned int index = to_index(priv, source);
> +
> +		ret = i2c_mux_add_adapter(priv->mux, 0, index, 0);
> +		if (ret < 0)
> +			goto error;
> +	}
> +
> +	return 0;
> +
> +error:
> +	i2c_mux_del_adapters(priv->mux);
> +	return ret;
> +}
> +
> +static void max9286_configure_i2c(struct max9286_priv *priv, bool localack)
> +{
> +	u8 config = MAX9286_I2CSLVSH_469NS_234NS | MAX9286_I2CSLVTO_1024US |
> +		    MAXIM_I2C_SPEED;
> +
> +	if (localack)
> +		config |= MAX9286_I2CLOCACK;
> +
> +	max9286_write(priv, 0x34, config);
> +	usleep_range(3000, 5000);
> +}
> +
> +/* -----------------------------------------------------------------------------
> + * V4L2 Subdev
> + */
> +
> +static int max9286_notify_bound(struct v4l2_async_notifier *notifier,
> +				struct v4l2_subdev *subdev,
> +				struct v4l2_async_subdev *asd)
> +{
> +	struct max9286_priv *priv = sd_to_max9286(notifier->sd);
> +	struct max9286_source *source = asd_to_max9286_source(asd);
> +	unsigned int index = to_index(priv, source);
> +	unsigned int src_pad;
> +	int ret;
> +
> +	ret = media_entity_get_fwnode_pad(&subdev->entity,
> +					  source->fwnode,
> +					  MEDIA_PAD_FL_SOURCE);
> +	if (ret < 0) {
> +		dev_err(&priv->client->dev,
> +			"Failed to find pad for %s\n", subdev->name);
> +		return ret;
> +	}
> +
> +	source->sd = subdev;
> +	src_pad = ret;
> +
> +	ret = media_create_pad_link(&source->sd->entity, src_pad,
> +				    &priv->sd.entity, index,
> +				    MEDIA_LNK_FL_ENABLED |
> +				    MEDIA_LNK_FL_IMMUTABLE);
> +	if (ret) {
> +		dev_err(&priv->client->dev,
> +			"Unable to link %s:%u -> %s:%u\n",
> +			source->sd->name, src_pad, priv->sd.name, index);
> +		return ret;
> +	}
> +
> +	dev_dbg(&priv->client->dev, "Bound %s pad: %u on index %u\n",
> +		subdev->name, src_pad, index);
> +
> +	return 0;
> +}
> +
> +static void max9286_notify_unbind(struct v4l2_async_notifier *notifier,
> +				  struct v4l2_subdev *subdev,
> +				  struct v4l2_async_subdev *asd)
> +{
> +	struct max9286_source *source = asd_to_max9286_source(asd);
> +
> +	source->sd = NULL;
> +}
> +
> +static const struct v4l2_async_notifier_operations max9286_notify_ops = {
> +	.bound = max9286_notify_bound,
> +	.unbind = max9286_notify_unbind,
> +};
> +
> +/*
> + * max9286_check_video_links() - Make sure video links are detected and locked
> + *
> + * Performs safety checks on video link status. Make sure they are detected
> + * and all enabled links are locked.
> + *
> + * Returns 0 for success, -EIO for errors.
> + */
> +static int max9286_check_video_links(struct max9286_priv *priv)
> +{
> +	unsigned int i;
> +	int ret;
> +
> +	/*
> +	 * Make sure valid video links are detected.
> +	 * The delay is not characterized in de-serializer manual, wait up
> +	 * to 5 ms.
> +	 */
> +	for (i = 0; i < 10; i++) {
> +		ret = max9286_read(priv, 0x49);
> +		if (ret < 0)
> +			return -EIO;
> +
> +		if ((ret & MAX9286_VIDEO_DETECT_MASK) == priv->source_mask)
> +			break;
> +
> +		usleep_range(350, 500);
> +	}
> +
> +	if (i == 10) {
> +		dev_err(&priv->client->dev,
> +			"Unable to detect video links: 0x%02x\n", ret);
> +		return -EIO;
> +	}
> +
> +	/* Make sure all enabled links are locked (4ms max). */
> +	for (i = 0; i < 10; i++) {
> +		ret = max9286_read(priv, 0x27);
> +		if (ret < 0)
> +			return -EIO;
> +
> +		if (ret & MAX9286_LOCKED)
> +			break;
> +
> +		usleep_range(350, 450);
> +	}
> +
> +	if (i == 10) {
> +		dev_err(&priv->client->dev, "Not all enabled links locked\n");
> +		return -EIO;
> +	}
> +
> +	return 0;
> +}
> +
> +static int max9286_s_stream(struct v4l2_subdev *sd, int enable)
> +{
> +	struct max9286_priv *priv = sd_to_max9286(sd);
> +	struct max9286_source *source;
> +	unsigned int i;
> +	bool sync = false;
> +	int ret;
> +
> +	if (enable) {
> +		/* FIXME: See note in max9286_i2c_mux_select() */
> +		priv->streaming = 1;
> +
> +		/* Start all cameras. */
> +		for_each_source(priv, source) {
> +			ret = v4l2_subdev_call(source->sd, video, s_stream, 1);
> +			if (ret)
> +				return ret;
> +		}
> +
> +		ret = max9286_check_video_links(priv);
> +		if (ret)
> +			return ret;
> +
> +		/*
> +		 * Wait until frame synchronization is locked.
> +		 *
> +		 * Manual says frame sync locking should take ~6 VTS.
> +		 * From pratical experience at least 8 are required. Give
> +		 * 12 complete frames time (~33ms at 30 fps) to achieve frame
> +		 * locking before returning error.
> +		 */
> +		for (i = 0; i < 36; i++) {
> +			if (max9286_read(priv, 0x31) & MAX9286_FSYNC_LOCKED) {
> +				sync = true;
> +				break;
> +			}
> +			usleep_range(9000, 11000);
> +		}
> +
> +		if (!sync) {
> +			dev_err(&priv->client->dev,
> +				"Failed to get frame synchronization\n");
> +			return -EINVAL;
> +		}
> +
> +		/*
> +		 * Enable CSI output, VC set according to link number.
> +		 * Bit 7 must be set (chip manual says it's 0 and reserved).
> +		 */
> +		max9286_write(priv, 0x15, 0x80 | MAX9286_VCTYPE |
> +			      MAX9286_CSIOUTEN | MAX9286_0X15_RESV);
> +	} else {
> +		max9286_write(priv, 0x15, MAX9286_VCTYPE | MAX9286_0X15_RESV);
> +
> +		/* Stop all cameras. */
> +		for_each_source(priv, source)
> +			v4l2_subdev_call(source->sd, video, s_stream, 0);
> +
> +		/* FIXME: See note in max9286_i2c_mux_select() */
> +		priv->streaming = 0;
> +	}
> +
> +	return 0;
> +}
> +
> +static int max9286_enum_mbus_code(struct v4l2_subdev *sd,
> +				  struct v4l2_subdev_pad_config *cfg,
> +				  struct v4l2_subdev_mbus_code_enum *code)
> +{
> +	if (code->pad || code->index > 0)
> +		return -EINVAL;
> +
> +	code->code = MEDIA_BUS_FMT_UYVY8_2X8;
> +
> +	return 0;
> +}
> +
> +static struct v4l2_mbus_framefmt *
> +max9286_get_pad_format(struct max9286_priv *priv,
> +		       struct v4l2_subdev_pad_config *cfg,
> +		       unsigned int pad, u32 which)
> +{
> +	switch (which) {
> +	case V4L2_SUBDEV_FORMAT_TRY:
> +		return v4l2_subdev_get_try_format(&priv->sd, cfg, pad);
> +	case V4L2_SUBDEV_FORMAT_ACTIVE:
> +		return &priv->fmt[pad];
> +	default:
> +		return NULL;
> +	}
> +}
> +
> +static int max9286_set_fmt(struct v4l2_subdev *sd,
> +			   struct v4l2_subdev_pad_config *cfg,
> +			   struct v4l2_subdev_format *format)
> +{
> +	struct max9286_priv *priv = sd_to_max9286(sd);
> +	struct v4l2_mbus_framefmt *cfg_fmt;
> +
> +	if (format->pad >= MAX9286_SRC_PAD)
> +		return -EINVAL;
> +
> +	/* Refuse non YUV422 formats as we hardcode DT to 8 bit YUV422 */
> +	switch (format->format.code) {
> +	case MEDIA_BUS_FMT_UYVY8_2X8:
> +	case MEDIA_BUS_FMT_VYUY8_2X8:
> +	case MEDIA_BUS_FMT_YUYV8_2X8:
> +	case MEDIA_BUS_FMT_YVYU8_2X8:
> +		break;
> +	default:
> +		format->format.code = MEDIA_BUS_FMT_YUYV8_2X8;
> +		break;
> +	}
> +
> +	cfg_fmt = max9286_get_pad_format(priv, cfg, format->pad, format->which);
> +	if (!cfg_fmt)
> +		return -EINVAL;
> +
> +	*cfg_fmt = format->format;
> +
> +	return 0;
> +}
> +
> +static int max9286_get_fmt(struct v4l2_subdev *sd,
> +			   struct v4l2_subdev_pad_config *cfg,
> +			   struct v4l2_subdev_format *format)
> +{
> +	struct max9286_priv *priv = sd_to_max9286(sd);
> +	struct v4l2_mbus_framefmt *cfg_fmt;
> +
> +	if (format->pad >= MAX9286_SRC_PAD)
> +		return -EINVAL;
> +
> +	cfg_fmt = max9286_get_pad_format(priv, cfg, format->pad, format->which);
> +	if (!cfg_fmt)
> +		return -EINVAL;
> +
> +	format->format = *cfg_fmt;
> +
> +	return 0;
> +}
> +
> +static const struct v4l2_subdev_video_ops max9286_video_ops = {
> +	.s_stream	= max9286_s_stream,
> +};
> +
> +static const struct v4l2_subdev_pad_ops max9286_pad_ops = {
> +	.enum_mbus_code = max9286_enum_mbus_code,
> +	.get_fmt	= max9286_get_fmt,
> +	.set_fmt	= max9286_set_fmt,
> +};
> +
> +static const struct v4l2_subdev_ops max9286_subdev_ops = {
> +	.video		= &max9286_video_ops,
> +	.pad		= &max9286_pad_ops,
> +};
> +
> +static void max9286_init_format(struct v4l2_mbus_framefmt *fmt)
> +{
> +	fmt->width		= 1280;
> +	fmt->height		= 800;
> +	fmt->code		= MEDIA_BUS_FMT_UYVY8_2X8;
> +	fmt->colorspace		= V4L2_COLORSPACE_SRGB;
> +	fmt->field		= V4L2_FIELD_NONE;
> +	fmt->ycbcr_enc		= V4L2_YCBCR_ENC_DEFAULT;
> +	fmt->quantization	= V4L2_QUANTIZATION_DEFAULT;
> +	fmt->xfer_func		= V4L2_XFER_FUNC_DEFAULT;
> +}
> +
> +static int max9286_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
> +{
> +	struct v4l2_mbus_framefmt *format;
> +	unsigned int i;
> +
> +	for (i = 0; i < MAX9286_N_SINKS; i++) {
> +		format = v4l2_subdev_get_try_format(subdev, fh->pad, i);
> +		max9286_init_format(format);
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct v4l2_subdev_internal_ops max9286_subdev_internal_ops = {
> +	.open = max9286_open,
> +};
> +
> +/* -----------------------------------------------------------------------------
> + * Probe/Remove
> + */
> +
> +static int max9286_setup(struct max9286_priv *priv)
> +{
> +	/*
> +	 * Link ordering values for all enabled links combinations. Orders must
> +	 * be assigned sequentially from 0 to the number of enabled links
> +	 * without leaving any hole for disabled links. We thus assign orders to
> +	 * enabled links first, and use the remaining order values for disabled
> +	 * links are all links must have a different order value;
> +	 */
> +	static const u8 link_order[] = {
> +		(3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xxxx */
> +		(3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xxx0 */
> +		(3 << 6) | (2 << 4) | (0 << 2) | (1 << 0), /* xx0x */
> +		(3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xx10 */
> +		(3 << 6) | (0 << 4) | (2 << 2) | (1 << 0), /* x0xx */
> +		(3 << 6) | (1 << 4) | (2 << 2) | (0 << 0), /* x1x0 */
> +		(3 << 6) | (1 << 4) | (0 << 2) | (2 << 0), /* x10x */
> +		(3 << 6) | (1 << 4) | (1 << 2) | (0 << 0), /* x210 */
> +		(0 << 6) | (3 << 4) | (2 << 2) | (1 << 0), /* 0xxx */
> +		(1 << 6) | (3 << 4) | (2 << 2) | (0 << 0), /* 1xx0 */
> +		(1 << 6) | (3 << 4) | (0 << 2) | (2 << 0), /* 1x0x */
> +		(2 << 6) | (3 << 4) | (1 << 2) | (0 << 0), /* 2x10 */
> +		(1 << 6) | (0 << 4) | (3 << 2) | (2 << 0), /* 10xx */
> +		(2 << 6) | (1 << 4) | (3 << 2) | (0 << 0), /* 21x0 */
> +		(2 << 6) | (1 << 4) | (0 << 2) | (3 << 0), /* 210x */
> +		(3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* 3210 */
> +	};
> +
> +	/*
> +	 * Set the I2C bus speed.
> +	 *
> +	 * Enable I2C Local Acknowledge during the probe sequences of the camera
> +	 * only. This should be disabled after the mux is initialised.
> +	 */
> +	max9286_configure_i2c(priv, true);
> +
> +	/*
> +	 * Reverse channel setup.
> +	 *
> +	 * - Enable custom reverse channel configuration (through register 0x3f)
> +	 *   and set the first pulse length to 35 clock cycles.
> +	 * - Increase the reverse channel amplitude to 170mV to accommodate the
> +	 *   high threshold enabled by the serializer driver.
> +	 */
> +	max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35));
> +	max9286_write(priv, 0x3b, MAX9286_REV_TRF(1) | MAX9286_REV_AMP(70) |
> +		      MAX9286_REV_AMP_X);
> +
> +	/*
> +	 * Enable GMSL links, mask unused ones and autodetect link
> +	 * used as CSI clock source.
> +	 */
> +	max9286_write(priv, 0x00, MAX9286_MSTLINKSEL_AUTO | priv->route_mask);
> +	max9286_write(priv, 0x0b, link_order[priv->route_mask]);
> +	max9286_write(priv, 0x69, (0xf & ~priv->route_mask));
> +
> +	/*
> +	 * Video format setup:
> +	 * Disable CSI output, VC is set accordingly to Link number.
> +	 */
> +	max9286_write(priv, 0x15, MAX9286_VCTYPE | MAX9286_0X15_RESV);
> +
> +	/* Enable CSI-2 Lane D0-D3 only, DBL mode, YUV422 8-bit. */
> +	max9286_write(priv, 0x12, MAX9286_CSIDBL | MAX9286_DBL |
> +		      MAX9286_CSILANECNT(priv->csi2_data_lanes) |
> +		      MAX9286_DATATYPE_YUV422_8BIT);
> +
> +	/* Automatic: FRAMESYNC taken from the slowest Link. */
> +	max9286_write(priv, 0x01, MAX9286_FSYNCMODE_INT_HIZ |
> +		      MAX9286_FSYNCMETH_AUTO);
> +
> +	/* Enable HS/VS encoding, use D14/15 for HS/VS, invert VS. */
> +	max9286_write(priv, 0x0c, MAX9286_HVEN | MAX9286_INVVS |
> +		      MAX9286_HVSRC_D14);
> +
> +	/*
> +	 * Wait for 2ms to allow the link to resynchronize after the
> +	 * configuration change.
> +	 */
> +	usleep_range(2000, 5000);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id max9286_dt_ids[] = {
> +	{ .compatible = "maxim,max9286" },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, max9286_dt_ids);
> +
> +static int max9286_init(struct device *dev)
> +{
> +	struct max9286_priv *priv;
> +	struct i2c_client *client;
> +	struct fwnode_handle *ep;
> +	unsigned int i;
> +	int ret;
> +
> +	/* Skip non-max9286 devices. */
> +	if (!dev->of_node || !of_match_node(max9286_dt_ids, dev->of_node))
> +		return 0;
> +
> +	client = to_i2c_client(dev);
> +	priv = i2c_get_clientdata(client);
> +
> +	/* Enable the bus power. */
> +	ret = regulator_enable(priv->regulator);
> +	if (ret < 0) {
> +		dev_err(&client->dev, "Unable to turn PoC on\n");
> +		return ret;
> +	}
> +
> +	priv->poc_enabled = true;
> +
> +	ret = max9286_setup(priv);
> +	if (ret) {
> +		dev_err(dev, "Unable to setup max9286\n");
> +		goto err_regulator;
> +	}
> +
> +	v4l2_i2c_subdev_init(&priv->sd, client, &max9286_subdev_ops);
> +	priv->sd.internal_ops = &max9286_subdev_internal_ops;
> +	priv->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> +
> +	v4l2_ctrl_handler_init(&priv->ctrls, 1);
> +	/*
> +	 * FIXME: Compute the real pixel rate. The 50 MP/s value comes from the
> +	 * hardcoded frequency in the BSP CSI-2 receiver driver.
> +	 */
> +	v4l2_ctrl_new_std(&priv->ctrls, NULL, V4L2_CID_PIXEL_RATE,
> +			  50000000, 50000000, 1, 50000000);
> +	priv->sd.ctrl_handler = &priv->ctrls;
> +	ret = priv->ctrls.error;
> +	if (ret)
> +		goto err_regulator;
> +
> +	priv->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
> +
> +	priv->pads[MAX9286_SRC_PAD].flags = MEDIA_PAD_FL_SOURCE;
> +	for (i = 0; i < MAX9286_SRC_PAD; i++)
> +		priv->pads[i].flags = MEDIA_PAD_FL_SINK;
> +	ret = media_entity_pads_init(&priv->sd.entity, MAX9286_N_PADS,
> +				     priv->pads);
> +	if (ret)
> +		goto err_regulator;
> +
> +	ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), MAX9286_SRC_PAD,
> +					     0, 0);
> +	if (!ep) {
> +		dev_err(dev, "Unable to retrieve endpoint on \"port@4\"\n");
> +		ret = -ENOENT;
> +		goto err_regulator;
> +	}
> +	priv->sd.fwnode = ep;
> +
> +	ret = v4l2_async_register_subdev(&priv->sd);
> +	if (ret < 0) {
> +		dev_err(dev, "Unable to register subdevice\n");
> +		goto err_put_node;
> +	}
> +
> +	ret = max9286_i2c_mux_init(priv);
> +	if (ret) {
> +		dev_err(dev, "Unable to initialize I2C multiplexer\n");
> +		goto err_subdev_unregister;
> +	}
> +
> +	/*
> +	 * Re-configure I2C with local acknowledge disabled after cameras
> +	 * have probed.
> +	 */
> +	max9286_configure_i2c(priv, false);
> +
> +	/* Leave the mux channels disabled until they are selected. */
> +	max9286_i2c_mux_close(priv);
> +
> +	return 0;
> +
> +err_subdev_unregister:
> +	v4l2_async_unregister_subdev(&priv->sd);
> +	max9286_i2c_mux_close(priv);
> +err_put_node:
> +	fwnode_handle_put(ep);
> +err_regulator:
> +	regulator_disable(priv->regulator);
> +	priv->poc_enabled = false;
> +
> +	return ret;
> +}
> +
> +static struct device_node *max9286_get_i2c_by_id(struct device_node *parent,
> +						 u32 id)
> +{
> +	struct device_node *child;
> +
> +	for_each_child_of_node(parent, child) {
> +		u32 i2c_id = 0;
> +
> +		if (of_node_cmp(child->name, "i2c") != 0)
> +			continue;
> +		of_property_read_u32(child, "reg", &i2c_id);
> +		if (id == i2c_id)
> +			return child;
> +	}
> +
> +	return NULL;
> +}
> +
> +static int max9286_check_i2c_bus_by_id(struct device *dev, int id)
> +{
> +	struct device_node *i2c_np;
> +
> +	i2c_np = max9286_get_i2c_by_id(dev->of_node, id);
> +	if (!i2c_np) {
> +		dev_err(dev, "Failed to find corresponding i2c@%u\n", id);
> +		return -ENODEV;
> +	}
> +
> +	if (!of_device_is_available(i2c_np)) {
> +		dev_dbg(dev, "Skipping port %u with disabled I2C bus\n", id);
> +		of_node_put(i2c_np);
> +		return -ENODEV;
> +	}
> +
> +	of_node_put(i2c_np);
> +
> +	return 0;
> +}
> +
> +static void max9286_cleanup_dt(struct max9286_priv *priv)
> +{
> +	struct max9286_source *source;
> +
> +	/*
> +	 * Not strictly part of the DT, but the notifier is registered during
> +	 * max9286_parse_dt(), and the notifier holds references to the fwnodes
> +	 * thus the cleanup is here to mirror the registration.
> +	 */
> +	v4l2_async_notifier_unregister(&priv->notifier);
> +	v4l2_async_notifier_cleanup(&priv->notifier);
> +
> +	for_each_source(priv, source) {
> +		fwnode_handle_put(source->fwnode);
> +		source->fwnode = NULL;
> +	}
> +}
> +
> +static int max9286_parse_dt(struct max9286_priv *priv)
> +{
> +	struct device *dev = &priv->client->dev;
> +	struct device_node *ep_np = NULL;
> +	int ret;
> +
> +	v4l2_async_notifier_init(&priv->notifier);
> +
> +	for_each_endpoint_of_node(dev->of_node, ep_np) {
> +		struct max9286_source *source;
> +		struct of_endpoint ep;
> +
> +		of_graph_parse_endpoint(ep_np, &ep);
> +		dev_dbg(dev, "Endpoint %pOF on port %d",
> +			ep.local_node, ep.port);
> +
> +		if (ep.port > MAX9286_NUM_GMSL) {
> +			dev_err(dev, "Invalid endpoint %s on port %d",
> +				of_node_full_name(ep.local_node), ep.port);
> +			continue;
> +		}
> +
> +		/* For the source endpoint just parse the bus configuration. */
> +		if (ep.port == MAX9286_SRC_PAD) {
> +			struct v4l2_fwnode_endpoint vep = { .bus_type = 0 };
> +			int ret;
> +
> +			ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_np),
> +							 &vep);
> +			if (ret)
> +				return ret;
> +
> +			if (vep.bus_type != V4L2_MBUS_CSI2_DPHY) {
> +				dev_err(dev,
> +					"Media bus %u type not supported\n",
> +					vep.bus_type);
> +				v4l2_fwnode_endpoint_free(&vep);
> +				return -EINVAL;
> +			}
> +
> +			priv->csi2_data_lanes =
> +				vep.bus.mipi_csi2.num_data_lanes;
> +			v4l2_fwnode_endpoint_free(&vep);
> +
> +			continue;
> +		}
> +
> +		/* Skip if the corresponding GMSL link is unavailable. */
> +		if (max9286_check_i2c_bus_by_id(dev, ep.port))
> +			continue;
> +
> +		if (priv->sources[ep.port].fwnode) {
> +			dev_err(dev,
> +				"Multiple port endpoints are not supported: %d",
> +				ep.port);
> +
> +			continue;
> +		}
> +
> +		source = &priv->sources[ep.port];
> +		source->fwnode = fwnode_graph_get_remote_endpoint(
> +						of_fwnode_handle(ep_np));
> +		if (!source->fwnode) {
> +			dev_err(dev,
> +				"Endpoint %pOF has no remote endpoint connection\n",
> +				ep.local_node);
> +
> +			continue;
> +		}
> +
> +		source->asd.match_type = V4L2_ASYNC_MATCH_FWNODE;
> +		source->asd.match.fwnode = source->fwnode;
> +
> +		ret = v4l2_async_notifier_add_subdev(&priv->notifier,
> +						     &source->asd);
> +		if (ret) {
> +			v4l2_async_notifier_cleanup(&priv->notifier);
> +			return ret;
> +		}
> +
> +		priv->source_mask |= BIT(ep.port);
> +		priv->nsources++;
> +	}
> +
> +	/* Do not register the subdev notifier if there are no devices. */
> +	if (!priv->nsources)
> +		return 0;
> +
> +	priv->route_mask = priv->source_mask;
> +	priv->notifier.ops = &max9286_notify_ops;
> +
> +	ret = v4l2_async_subdev_notifier_register(&priv->sd, &priv->notifier);
> +	if (ret)
> +		v4l2_async_notifier_cleanup(&priv->notifier);
> +
> +	return 0;
> +}
> +
> +static int max9286_probe(struct i2c_client *client,
> +			 const struct i2c_device_id *did)
> +{
> +	struct max9286_priv *priv;
> +	unsigned int i;
> +	int ret;
> +
> +	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	priv->client = client;
> +	i2c_set_clientdata(client, priv);
> +
> +	for (i = 0; i < MAX9286_N_SINKS; i++)
> +		max9286_init_format(&priv->fmt[i]);
> +
> +	ret = max9286_parse_dt(priv);
> +	if (ret)
> +		return ret;
> +
> +	priv->regulator = regulator_get(&client->dev, "poc");
> +	if (IS_ERR(priv->regulator)) {
> +		if (PTR_ERR(priv->regulator) != -EPROBE_DEFER)
> +			dev_err(&client->dev,
> +				"Unable to get PoC regulator (%ld)\n",
> +				PTR_ERR(priv->regulator));
> +		ret = PTR_ERR(priv->regulator);
> +		goto err_free;
> +	}
> +
> +	/*
> +	 * We can have multiple MAX9286 instances on the same physical I2C
> +	 * bus, and I2C children behind ports of separate MAX9286 instances
> +	 * having the same I2C address. As the MAX9286 starts by default with
> +	 * all ports enabled, we need to disable all ports on all MAX9286
> +	 * instances before proceeding to further initialize the devices and
> +	 * instantiate children.
> +	 *
> +	 * Start by just disabling all channels on the current device. Then,
> +	 * if all other MAX9286 on the parent bus have been probed, proceed
> +	 * to initialize them all, including the current one.
> +	 */
> +	max9286_i2c_mux_close(priv);
> +
> +	/*
> +	 * The MAX9286 initialises with auto-acknowledge enabled by default.
> +	 * This means that if multiple MAX9286 devices are connected to an I2C
> +	 * bus, another MAX9286 could ack I2C transfers meant for a device on
> +	 * the other side of the GMSL links for this MAX9286 (such as a
> +	 * MAX9271). To prevent that disable auto-acknowledge early on; it
> +	 * will be enabled later as needed.
> +	 */
> +	max9286_configure_i2c(priv, false);
> +
> +	ret = max9286_init(&client->dev);
> +	if (ret < 0)
> +		goto err_regulator;
> +
> +	return 0;
> +
> +err_regulator:
> +	regulator_put(priv->regulator);
> +	max9286_i2c_mux_close(priv);
> +	max9286_configure_i2c(priv, false);
> +err_free:
> +	max9286_cleanup_dt(priv);
> +	kfree(priv);
> +
> +	return ret;
> +}
> +
> +static int max9286_remove(struct i2c_client *client)
> +{
> +	struct max9286_priv *priv = i2c_get_clientdata(client);
> +
> +	i2c_mux_del_adapters(priv->mux);
> +
> +	fwnode_handle_put(priv->sd.fwnode);
> +	v4l2_async_unregister_subdev(&priv->sd);
> +
> +	if (priv->poc_enabled)
> +		regulator_disable(priv->regulator);
> +	regulator_put(priv->regulator);
> +
> +	max9286_cleanup_dt(priv);
> +	kfree(priv);
> +
> +	return 0;
> +}
> +
> +static const struct i2c_device_id max9286_id[] = {
> +	{ "max9286", 0 },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(i2c, max9286_id);
> +
> +static struct i2c_driver max9286_i2c_driver = {
> +	.driver	= {
> +		.name		= "max9286",
> +		.of_match_table	= of_match_ptr(max9286_dt_ids),
> +	},
> +	.probe		= max9286_probe,
> +	.remove		= max9286_remove,
> +	.id_table	= max9286_id,
> +};
> +
> +module_i2c_driver(max9286_i2c_driver);
> +
> +MODULE_DESCRIPTION("Maxim MAX9286 GMSL Deserializer Driver");
> +MODULE_AUTHOR("Jacopo Mondi, Kieran Bingham, Laurent Pinchart, Niklas Söderlund, Vladimir Barinov");
> +MODULE_LICENSE("GPL");
>
Niklas Söderlund Aug. 9, 2019, 12:04 p.m. UTC | #2
Hi Kieran,

Thanks for your feedback.

On 2019-08-09 09:09:43 +0100, Kieran Bingham wrote:
> Hi Niklas,
> 
> This should be at least v5.

I don't agree ;-) This is a "new" series where multiple streams are not 
supported and there are no external dependencies. To indicate this I 
reset the version. I don't feel strongly about this next submission can 
remedy this if you do feel strongly about it.

> 
> Did you take the last v4 and work from there?
> I have made changes since the last posting. Did you get an update from
> my branches?
> 
> What changes have you made to this posting compared to whichever
> patch-base you have taken to start from?

I took my latest known good state and diffed it with all gmsl branches i 
could find picked what seamed most recent. Then I removed multiplexed 
stream support, fixed a few todos in error paths to clean up notifiers 
and unified naming of the private data structure.
Kieran Bingham Aug. 9, 2019, 12:12 p.m. UTC | #3
On 09/08/2019 13:04, Niklas Söderlund wrote:
> Hi Kieran,
> 
> Thanks for your feedback.
> 
> On 2019-08-09 09:09:43 +0100, Kieran Bingham wrote:
>> Hi Niklas,
>>
>> This should be at least v5.
> 
> I don't agree ;-) This is a "new" series where multiple streams are not 
> supported and there are no external dependencies. To indicate this I 

I'm afraid there's nothing new about a version of this series with
support for only a single stream.

See version 2 of my series:

https://lore.kernel.org/linux-media/20180808165559.29957-4-kieran.bingham@ideasonboard.com/


> reset the version. I don't feel strongly about this next submission can 
> remedy this if you do feel strongly about it.

I find it very confusing to have reset the version but kept exactly the
same patch title.

It's a fork of the series :D

>> Did you take the last v4 and work from there?
>> I have made changes since the last posting. Did you get an update from
>> my branches?
>>
>> What changes have you made to this posting compared to whichever
>> patch-base you have taken to start from?
> 
> I took my latest known good state and diffed it with all gmsl branches i 
> could find picked what seamed most recent. Then I removed multiplexed 
> stream support, fixed a few todos in error paths to clean up notifiers 
> and unified naming of the private data structure.


I'll diff your version with my latest.

There were other review comments worked on from Sakari too., and there
is an outstanding comment from Rob to complete on the bindings from v4.

--
Kieran
Niklas Söderlund Aug. 9, 2019, 12:23 p.m. UTC | #4
Hi Kieran,

On 2019-08-09 13:12:49 +0100, Kieran Bingham wrote:
> On 09/08/2019 13:04, Niklas Söderlund wrote:
> > Hi Kieran,
> > 
> > Thanks for your feedback.
> > 
> > On 2019-08-09 09:09:43 +0100, Kieran Bingham wrote:
> >> Hi Niklas,
> >>
> >> This should be at least v5.
> > 
> > I don't agree ;-) This is a "new" series where multiple streams are not 
> > supported and there are no external dependencies. To indicate this I 
> 
> I'm afraid there's nothing new about a version of this series with
> support for only a single stream.
> 
> See version 2 of my series:
> 
> https://lore.kernel.org/linux-media/20180808165559.29957-4-kieran.bingham@ideasonboard.com/

Was not aware of this posting, then yes I do agree with you this should 
have been v5. Sorry about that.

> 
> 
> > reset the version. I don't feel strongly about this next submission can 
> > remedy this if you do feel strongly about it.
> 
> I find it very confusing to have reset the version but kept exactly the
> same patch title.
> 
> It's a fork of the series :D

:-)

I think this proves we need to get this driver upstream so we can start 
submitting patches towards something and not brew our our brand of stuff 
we have laying around and find all over the place.

> 
> >> Did you take the last v4 and work from there?
> >> I have made changes since the last posting. Did you get an update from
> >> my branches?
> >>
> >> What changes have you made to this posting compared to whichever
> >> patch-base you have taken to start from?
> > 
> > I took my latest known good state and diffed it with all gmsl branches i 
> > could find picked what seamed most recent. Then I removed multiplexed 
> > stream support, fixed a few todos in error paths to clean up notifiers 
> > and unified naming of the private data structure.
> 
> 
> I'll diff your version with my latest.
> 
> There were other review comments worked on from Sakari too., and there
> is an outstanding comment from Rob to complete on the bindings from v4.
> 
> --
> Kieran
> 
> 
>
Kieran Bingham Aug. 9, 2019, 12:59 p.m. UTC | #5
Hi Niklas,

On 09/08/2019 13:23, Niklas Söderlund wrote:
> Hi Kieran,
> 
> On 2019-08-09 13:12:49 +0100, Kieran Bingham wrote:
>> On 09/08/2019 13:04, Niklas Söderlund wrote:
>>> Hi Kieran,
>>>
>>> Thanks for your feedback.
>>>
>>> On 2019-08-09 09:09:43 +0100, Kieran Bingham wrote:
>>>> Hi Niklas,
>>>>
>>>> This should be at least v5.
>>>
>>> I don't agree ;-) This is a "new" series where multiple streams are not 
>>> supported and there are no external dependencies. To indicate this I 
>>
>> I'm afraid there's nothing new about a version of this series with
>> support for only a single stream.
>>
>> See version 2 of my series:
>>
>> https://lore.kernel.org/linux-media/20180808165559.29957-4-kieran.bingham@ideasonboard.com/
> 
> Was not aware of this posting, then yes I do agree with you this should 
> have been v5. Sorry about that.
> 
>>
>>
>>> reset the version. I don't feel strongly about this next submission can 
>>> remedy this if you do feel strongly about it.
>>
>> I find it very confusing to have reset the version but kept exactly the
>> same patch title.
>>
>> It's a fork of the series :D
> 
> :-)
> 
> I think this proves we need to get this driver upstream so we can start 
> submitting patches towards something and not brew our our brand of stuff 
> we have laying around and find all over the place.

I agree, It's unfortunate that the direction has rotated too many times
for this driver.

Originally it was posted with VC support as that was our development,
then I removed the VC support (v2, v3) to aim to get it upstreamed.

I can't recall now why V4 occurred with VC brought back in - but perhaps
it was because the VC work was in active development at the time - and I
thought it was making progress, but it soon became a blocker - and was
not worked on until Jacopo started looking at it again recently - and
became a complete block to reposting any V5 of MAX9286 - as the VC work
was out of date and not being rebased.

Anyway, I agree - that getting a non-multi-stream capable version of
this integrated is very beneficial, so please do continue and post a v5
(or v6 if you deem more appropriate).

Please make sure all pending review comments are explored (especially
the one from Rob Herring about using an i2c-mux node) before posting
your next version though.

--
Kieran



>>>> Did you take the last v4 and work from there?
>>>> I have made changes since the last posting. Did you get an update from
>>>> my branches?
>>>>
>>>> What changes have you made to this posting compared to whichever
>>>> patch-base you have taken to start from?
>>>
>>> I took my latest known good state and diffed it with all gmsl branches i 
>>> could find picked what seamed most recent. Then I removed multiplexed 
>>> stream support, fixed a few todos in error paths to clean up notifiers 
>>> and unified naming of the private data structure.
>>
>>
>> I'll diff your version with my latest.
>>
>> There were other review comments worked on from Sakari too., and there
>> is an outstanding comment from Rob to complete on the bindings from v4.
>>
>> --
>> Kieran
>>
>>
>>
>

Patch
diff mbox series

diff --git a/MAINTAINERS b/MAINTAINERS
index 6426db5198f05377..f8f028811feee489 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9746,6 +9746,16 @@  F:	Documentation/devicetree/bindings/hwmon/max6697.txt
 F:	drivers/hwmon/max6697.c
 F:	include/linux/platform_data/max6697.h
 
+MAX9286 QUAD GMSL DESERIALIZER DRIVER
+M:	Jacopo Mondi <jacopo+renesas@jmondi.org>
+M:	Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
+M:	Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+M:	Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/media/i2c/maxim,max9286.txt
+F:	drivers/media/i2c/max9286.c
+
 MAX9860 MONO AUDIO VOICE CODEC DRIVER
 M:	Peter Rosin <peda@axentia.se>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 79ce9ec6fc1be1e6..c20b151a16e64349 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -439,6 +439,17 @@  config VIDEO_VPX3220
 	  To compile this driver as a module, choose M here: the
 	  module will be called vpx3220.
 
+config VIDEO_MAX9286
+	tristate "Maxim MAX9286 GMSL deserializer support"
+	depends on I2C && I2C_MUX
+	depends on VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER
+	select V4L2_FWNODE
+	help
+	  This driver supports the Maxim MAX9286 GMSL deserializer.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called max9286.
+
 comment "Video and audio decoders"
 
 config VIDEO_SAA717X
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index fd4ea86dedd5df44..25b3c7e5becfa714 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -114,5 +114,6 @@  obj-$(CONFIG_VIDEO_IMX274)	+= imx274.o
 obj-$(CONFIG_VIDEO_IMX319)	+= imx319.o
 obj-$(CONFIG_VIDEO_IMX355)	+= imx355.o
 obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o
+obj-$(CONFIG_VIDEO_MAX9286)	+= max9286.o
 
 obj-$(CONFIG_SDR_MAX2175) += max2175.o
diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c
new file mode 100644
index 0000000000000000..debd11ac269d28ca
--- /dev/null
+++ b/drivers/media/i2c/max9286.c
@@ -0,0 +1,1081 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Maxim MAX9286 GMSL Deserializer Driver
+ *
+ * Copyright (C) 2017-2018 Jacopo Mondi
+ * Copyright (C) 2017-2018 Kieran Bingham
+ * Copyright (C) 2017-2018 Laurent Pinchart
+ * Copyright (C) 2017-2018 Niklas Söderlund
+ * Copyright (C) 2016 Renesas Electronics Corporation
+ * Copyright (C) 2015 Cogent Embedded, Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/fwnode.h>
+#include <linux/i2c.h>
+#include <linux/i2c-mux.h>
+#include <linux/module.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-subdev.h>
+
+/* Register 0x00 */
+#define MAX9286_MSTLINKSEL_AUTO		(7 << 5)
+#define MAX9286_MSTLINKSEL(n)		((n) << 5)
+#define MAX9286_EN_VS_GEN		BIT(4)
+#define MAX9286_LINKEN(n)		(1 << (n))
+/* Register 0x01 */
+#define MAX9286_FSYNCMODE_ECU		(3 << 6)
+#define MAX9286_FSYNCMODE_EXT		(2 << 6)
+#define MAX9286_FSYNCMODE_INT_OUT	(1 << 6)
+#define MAX9286_FSYNCMODE_INT_HIZ	(0 << 6)
+#define MAX9286_GPIEN			BIT(5)
+#define MAX9286_ENLMO_RSTFSYNC		BIT(2)
+#define MAX9286_FSYNCMETH_AUTO		(2 << 0)
+#define MAX9286_FSYNCMETH_SEMI_AUTO	(1 << 0)
+#define MAX9286_FSYNCMETH_MANUAL	(0 << 0)
+#define MAX9286_REG_FSYNC_PERIOD_L	0x06
+#define MAX9286_REG_FSYNC_PERIOD_M	0x07
+#define MAX9286_REG_FSYNC_PERIOD_H	0x08
+/* Register 0x0a */
+#define MAX9286_FWDCCEN(n)		(1 << ((n) + 4))
+#define MAX9286_REVCCEN(n)		(1 << (n))
+/* Register 0x0c */
+#define MAX9286_HVEN			BIT(7)
+#define MAX9286_EDC_6BIT_HAMMING	(2 << 5)
+#define MAX9286_EDC_6BIT_CRC		(1 << 5)
+#define MAX9286_EDC_1BIT_PARITY		(0 << 5)
+#define MAX9286_DESEL			BIT(4)
+#define MAX9286_INVVS			BIT(3)
+#define MAX9286_INVHS			BIT(2)
+#define MAX9286_HVSRC_D0		(2 << 0)
+#define MAX9286_HVSRC_D14		(1 << 0)
+#define MAX9286_HVSRC_D18		(0 << 0)
+/* Register 0x12 */
+#define MAX9286_CSILANECNT(n)		(((n) - 1) << 6)
+#define MAX9286_CSIDBL			BIT(5)
+#define MAX9286_DBL			BIT(4)
+#define MAX9286_DATATYPE_USER_8BIT	(11 << 0)
+#define MAX9286_DATATYPE_USER_YUV_12BIT	(10 << 0)
+#define MAX9286_DATATYPE_USER_24BIT	(9 << 0)
+#define MAX9286_DATATYPE_RAW14		(8 << 0)
+#define MAX9286_DATATYPE_RAW11		(7 << 0)
+#define MAX9286_DATATYPE_RAW10		(6 << 0)
+#define MAX9286_DATATYPE_RAW8		(5 << 0)
+#define MAX9286_DATATYPE_YUV422_10BIT	(4 << 0)
+#define MAX9286_DATATYPE_YUV422_8BIT	(3 << 0)
+#define MAX9286_DATATYPE_RGB555		(2 << 0)
+#define MAX9286_DATATYPE_RGB565		(1 << 0)
+#define MAX9286_DATATYPE_RGB888		(0 << 0)
+/* Register 0x15 */
+#define MAX9286_VC(n)			((n) << 5)
+#define MAX9286_VCTYPE			BIT(4)
+#define MAX9286_CSIOUTEN		BIT(3)
+#define MAX9286_0X15_RESV		(3 << 0)
+/* Register 0x1b */
+#define MAX9286_SWITCHIN(n)		(1 << ((n) + 4))
+#define MAX9286_ENEQ(n)			(1 << (n))
+/* Register 0x27 */
+#define MAX9286_LOCKED			BIT(7)
+/* Register 0x31 */
+#define MAX9286_FSYNC_LOCKED		BIT(6)
+/* Register 0x34 */
+#define MAX9286_I2CLOCACK		BIT(7)
+#define MAX9286_I2CSLVSH_1046NS_469NS	(3 << 5)
+#define MAX9286_I2CSLVSH_938NS_352NS	(2 << 5)
+#define MAX9286_I2CSLVSH_469NS_234NS	(1 << 5)
+#define MAX9286_I2CSLVSH_352NS_117NS	(0 << 5)
+#define MAX9286_I2CMSTBT_837KBPS	(7 << 2)
+#define MAX9286_I2CMSTBT_533KBPS	(6 << 2)
+#define MAX9286_I2CMSTBT_339KBPS	(5 << 2)
+#define MAX9286_I2CMSTBT_173KBPS	(4 << 2)
+#define MAX9286_I2CMSTBT_105KBPS	(3 << 2)
+#define MAX9286_I2CMSTBT_84KBPS		(2 << 2)
+#define MAX9286_I2CMSTBT_28KBPS		(1 << 2)
+#define MAX9286_I2CMSTBT_8KBPS		(0 << 2)
+#define MAX9286_I2CSLVTO_NONE		(3 << 0)
+#define MAX9286_I2CSLVTO_1024US		(2 << 0)
+#define MAX9286_I2CSLVTO_256US		(1 << 0)
+#define MAX9286_I2CSLVTO_64US		(0 << 0)
+/* Register 0x3b */
+#define MAX9286_REV_TRF(n)		((n) << 4)
+#define MAX9286_REV_AMP(n)		((((n) - 30) / 10) << 1) /* in mV */
+#define MAX9286_REV_AMP_X		BIT(0)
+/* Register 0x3f */
+#define MAX9286_EN_REV_CFG		BIT(6)
+#define MAX9286_REV_FLEN(n)		((n) - 20)
+/* Register 0x49 */
+#define MAX9286_VIDEO_DETECT_MASK	0x0f
+/* Register 0x69 */
+#define MAX9286_LFLTBMONMASKED		BIT(7)
+#define MAX9286_LOCKMONMASKED		BIT(6)
+#define MAX9286_AUTOCOMBACKEN		BIT(5)
+#define MAX9286_AUTOMASKEN		BIT(4)
+#define MAX9286_MASKLINK(n)		((n) << 0)
+
+#define MAX9286_NUM_GMSL		4
+#define MAX9286_N_SINKS			4
+#define MAX9286_N_PADS			5
+#define MAX9286_SRC_PAD			4
+
+#define MAXIM_I2C_I2C_SPEED_400KHZ	MAX9286_I2CMSTBT_339KBPS
+#define MAXIM_I2C_I2C_SPEED_100KHZ	MAX9286_I2CMSTBT_105KBPS
+#define MAXIM_I2C_SPEED			MAXIM_I2C_I2C_SPEED_100KHZ
+
+struct max9286_source {
+	struct v4l2_async_subdev asd;
+	struct v4l2_subdev *sd;
+	struct fwnode_handle *fwnode;
+};
+
+#define asd_to_max9286_source(_asd) \
+	container_of(_asd, struct max9286_source, asd)
+
+struct max9286_priv {
+	struct i2c_client *client;
+	struct v4l2_subdev sd;
+	struct media_pad pads[MAX9286_N_PADS];
+	struct regulator *regulator;
+	bool poc_enabled;
+	int streaming;
+
+	struct i2c_mux_core *mux;
+	unsigned int mux_channel;
+
+	struct v4l2_ctrl_handler ctrls;
+
+	struct v4l2_mbus_framefmt fmt[MAX9286_N_SINKS];
+
+	unsigned int nsources;
+	unsigned int source_mask;
+	unsigned int route_mask;
+	unsigned int csi2_data_lanes;
+	struct max9286_source sources[MAX9286_NUM_GMSL];
+	struct v4l2_async_notifier notifier;
+};
+
+static struct max9286_source *next_source(struct max9286_priv *priv,
+					  struct max9286_source *source)
+{
+	if (!source)
+		source = &priv->sources[0];
+	else
+		source++;
+
+	for (; source < &priv->sources[MAX9286_NUM_GMSL]; source++) {
+		if (source->fwnode)
+			return source;
+	}
+
+	return NULL;
+}
+
+#define for_each_source(max9286, source) \
+	for (source = NULL; (source = next_source(max9286, source)); )
+
+#define to_index(max9286, source) (source - &max9286->sources[0])
+
+static inline struct max9286_priv *sd_to_max9286(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct max9286_priv, sd);
+}
+
+/* -----------------------------------------------------------------------------
+ * I2C IO
+ */
+
+static int max9286_read(struct max9286_priv *priv, u8 reg)
+{
+	int ret;
+
+	ret = i2c_smbus_read_byte_data(priv->client, reg);
+	if (ret < 0)
+		dev_err(&priv->client->dev,
+			"%s: register 0x%02x read failed (%d)\n",
+			__func__, reg, ret);
+
+	return ret;
+}
+
+static int max9286_write(struct max9286_priv *priv, u8 reg, u8 val)
+{
+	int ret;
+
+	ret = i2c_smbus_write_byte_data(priv->client, reg, val);
+	if (ret < 0)
+		dev_err(&priv->client->dev,
+			"%s: register 0x%02x write failed (%d)\n",
+			__func__, reg, ret);
+
+	return ret;
+}
+
+/* -----------------------------------------------------------------------------
+ * I2C Multiplexer
+ */
+
+static int max9286_i2c_mux_close(struct max9286_priv *priv)
+{
+	/* FIXME: See note in max9286_i2c_mux_select() */
+	if (priv->streaming)
+		return 0;
+	/*
+	 * Ensure that both the forward and reverse channel are disabled on the
+	 * mux, and that the channel ID is invalidated to ensure we reconfigure
+	 * on the next select call.
+	 */
+	priv->mux_channel = -1;
+	max9286_write(priv, 0x0a, 0x00);
+	usleep_range(3000, 5000);
+
+	return 0;
+}
+
+static int max9286_i2c_mux_select(struct i2c_mux_core *muxc, u32 chan)
+{
+	struct max9286_priv *priv = i2c_mux_priv(muxc);
+
+	/*
+	 * FIXME: This state keeping is a hack and do the job. It should
+	 * be should be reworked. One option to consider is that once all
+	 * cameras are programmed the mux selection logic should be disabled
+	 * and all all reverse and forward channels enable all the time.
+	 *
+	 * In any case this logic with a int that have two states should be
+	 * reworked!
+	 */
+	if (priv->streaming == 1) {
+		max9286_write(priv, 0x0a, 0xff);
+		priv->streaming = 2;
+		return 0;
+	} else if (priv->streaming == 2) {
+		return 0;
+	}
+
+	if (priv->mux_channel == chan)
+		return 0;
+
+	priv->mux_channel = chan;
+
+	max9286_write(priv, 0x0a,
+		      MAX9286_FWDCCEN(chan) | MAX9286_REVCCEN(chan));
+
+	/*
+	 * We must sleep after any change to the forward or reverse channel
+	 * configuration.
+	 */
+	usleep_range(3000, 5000);
+
+	return 0;
+}
+
+static int max9286_i2c_mux_init(struct max9286_priv *priv)
+{
+	struct max9286_source *source;
+	int ret;
+
+	if (!i2c_check_functionality(priv->client->adapter,
+				     I2C_FUNC_SMBUS_WRITE_BYTE_DATA))
+		return -ENODEV;
+
+	priv->mux = i2c_mux_alloc(priv->client->adapter, &priv->client->dev,
+				 priv->nsources, 0, I2C_MUX_LOCKED,
+				 max9286_i2c_mux_select, NULL);
+	if (!priv->mux)
+		return -ENOMEM;
+
+	priv->mux->priv = priv;
+
+	for_each_source(priv, source) {
+		unsigned int index = to_index(priv, source);
+
+		ret = i2c_mux_add_adapter(priv->mux, 0, index, 0);
+		if (ret < 0)
+			goto error;
+	}
+
+	return 0;
+
+error:
+	i2c_mux_del_adapters(priv->mux);
+	return ret;
+}
+
+static void max9286_configure_i2c(struct max9286_priv *priv, bool localack)
+{
+	u8 config = MAX9286_I2CSLVSH_469NS_234NS | MAX9286_I2CSLVTO_1024US |
+		    MAXIM_I2C_SPEED;
+
+	if (localack)
+		config |= MAX9286_I2CLOCACK;
+
+	max9286_write(priv, 0x34, config);
+	usleep_range(3000, 5000);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdev
+ */
+
+static int max9286_notify_bound(struct v4l2_async_notifier *notifier,
+				struct v4l2_subdev *subdev,
+				struct v4l2_async_subdev *asd)
+{
+	struct max9286_priv *priv = sd_to_max9286(notifier->sd);
+	struct max9286_source *source = asd_to_max9286_source(asd);
+	unsigned int index = to_index(priv, source);
+	unsigned int src_pad;
+	int ret;
+
+	ret = media_entity_get_fwnode_pad(&subdev->entity,
+					  source->fwnode,
+					  MEDIA_PAD_FL_SOURCE);
+	if (ret < 0) {
+		dev_err(&priv->client->dev,
+			"Failed to find pad for %s\n", subdev->name);
+		return ret;
+	}
+
+	source->sd = subdev;
+	src_pad = ret;
+
+	ret = media_create_pad_link(&source->sd->entity, src_pad,
+				    &priv->sd.entity, index,
+				    MEDIA_LNK_FL_ENABLED |
+				    MEDIA_LNK_FL_IMMUTABLE);
+	if (ret) {
+		dev_err(&priv->client->dev,
+			"Unable to link %s:%u -> %s:%u\n",
+			source->sd->name, src_pad, priv->sd.name, index);
+		return ret;
+	}
+
+	dev_dbg(&priv->client->dev, "Bound %s pad: %u on index %u\n",
+		subdev->name, src_pad, index);
+
+	return 0;
+}
+
+static void max9286_notify_unbind(struct v4l2_async_notifier *notifier,
+				  struct v4l2_subdev *subdev,
+				  struct v4l2_async_subdev *asd)
+{
+	struct max9286_source *source = asd_to_max9286_source(asd);
+
+	source->sd = NULL;
+}
+
+static const struct v4l2_async_notifier_operations max9286_notify_ops = {
+	.bound = max9286_notify_bound,
+	.unbind = max9286_notify_unbind,
+};
+
+/*
+ * max9286_check_video_links() - Make sure video links are detected and locked
+ *
+ * Performs safety checks on video link status. Make sure they are detected
+ * and all enabled links are locked.
+ *
+ * Returns 0 for success, -EIO for errors.
+ */
+static int max9286_check_video_links(struct max9286_priv *priv)
+{
+	unsigned int i;
+	int ret;
+
+	/*
+	 * Make sure valid video links are detected.
+	 * The delay is not characterized in de-serializer manual, wait up
+	 * to 5 ms.
+	 */
+	for (i = 0; i < 10; i++) {
+		ret = max9286_read(priv, 0x49);
+		if (ret < 0)
+			return -EIO;
+
+		if ((ret & MAX9286_VIDEO_DETECT_MASK) == priv->source_mask)
+			break;
+
+		usleep_range(350, 500);
+	}
+
+	if (i == 10) {
+		dev_err(&priv->client->dev,
+			"Unable to detect video links: 0x%02x\n", ret);
+		return -EIO;
+	}
+
+	/* Make sure all enabled links are locked (4ms max). */
+	for (i = 0; i < 10; i++) {
+		ret = max9286_read(priv, 0x27);
+		if (ret < 0)
+			return -EIO;
+
+		if (ret & MAX9286_LOCKED)
+			break;
+
+		usleep_range(350, 450);
+	}
+
+	if (i == 10) {
+		dev_err(&priv->client->dev, "Not all enabled links locked\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int max9286_s_stream(struct v4l2_subdev *sd, int enable)
+{
+	struct max9286_priv *priv = sd_to_max9286(sd);
+	struct max9286_source *source;
+	unsigned int i;
+	bool sync = false;
+	int ret;
+
+	if (enable) {
+		/* FIXME: See note in max9286_i2c_mux_select() */
+		priv->streaming = 1;
+
+		/* Start all cameras. */
+		for_each_source(priv, source) {
+			ret = v4l2_subdev_call(source->sd, video, s_stream, 1);
+			if (ret)
+				return ret;
+		}
+
+		ret = max9286_check_video_links(priv);
+		if (ret)
+			return ret;
+
+		/*
+		 * Wait until frame synchronization is locked.
+		 *
+		 * Manual says frame sync locking should take ~6 VTS.
+		 * From pratical experience at least 8 are required. Give
+		 * 12 complete frames time (~33ms at 30 fps) to achieve frame
+		 * locking before returning error.
+		 */
+		for (i = 0; i < 36; i++) {
+			if (max9286_read(priv, 0x31) & MAX9286_FSYNC_LOCKED) {
+				sync = true;
+				break;
+			}
+			usleep_range(9000, 11000);
+		}
+
+		if (!sync) {
+			dev_err(&priv->client->dev,
+				"Failed to get frame synchronization\n");
+			return -EINVAL;
+		}
+
+		/*
+		 * Enable CSI output, VC set according to link number.
+		 * Bit 7 must be set (chip manual says it's 0 and reserved).
+		 */
+		max9286_write(priv, 0x15, 0x80 | MAX9286_VCTYPE |
+			      MAX9286_CSIOUTEN | MAX9286_0X15_RESV);
+	} else {
+		max9286_write(priv, 0x15, MAX9286_VCTYPE | MAX9286_0X15_RESV);
+
+		/* Stop all cameras. */
+		for_each_source(priv, source)
+			v4l2_subdev_call(source->sd, video, s_stream, 0);
+
+		/* FIXME: See note in max9286_i2c_mux_select() */
+		priv->streaming = 0;
+	}
+
+	return 0;
+}
+
+static int max9286_enum_mbus_code(struct v4l2_subdev *sd,
+				  struct v4l2_subdev_pad_config *cfg,
+				  struct v4l2_subdev_mbus_code_enum *code)
+{
+	if (code->pad || code->index > 0)
+		return -EINVAL;
+
+	code->code = MEDIA_BUS_FMT_UYVY8_2X8;
+
+	return 0;
+}
+
+static struct v4l2_mbus_framefmt *
+max9286_get_pad_format(struct max9286_priv *priv,
+		       struct v4l2_subdev_pad_config *cfg,
+		       unsigned int pad, u32 which)
+{
+	switch (which) {
+	case V4L2_SUBDEV_FORMAT_TRY:
+		return v4l2_subdev_get_try_format(&priv->sd, cfg, pad);
+	case V4L2_SUBDEV_FORMAT_ACTIVE:
+		return &priv->fmt[pad];
+	default:
+		return NULL;
+	}
+}
+
+static int max9286_set_fmt(struct v4l2_subdev *sd,
+			   struct v4l2_subdev_pad_config *cfg,
+			   struct v4l2_subdev_format *format)
+{
+	struct max9286_priv *priv = sd_to_max9286(sd);
+	struct v4l2_mbus_framefmt *cfg_fmt;
+
+	if (format->pad >= MAX9286_SRC_PAD)
+		return -EINVAL;
+
+	/* Refuse non YUV422 formats as we hardcode DT to 8 bit YUV422 */
+	switch (format->format.code) {
+	case MEDIA_BUS_FMT_UYVY8_2X8:
+	case MEDIA_BUS_FMT_VYUY8_2X8:
+	case MEDIA_BUS_FMT_YUYV8_2X8:
+	case MEDIA_BUS_FMT_YVYU8_2X8:
+		break;
+	default:
+		format->format.code = MEDIA_BUS_FMT_YUYV8_2X8;
+		break;
+	}
+
+	cfg_fmt = max9286_get_pad_format(priv, cfg, format->pad, format->which);
+	if (!cfg_fmt)
+		return -EINVAL;
+
+	*cfg_fmt = format->format;
+
+	return 0;
+}
+
+static int max9286_get_fmt(struct v4l2_subdev *sd,
+			   struct v4l2_subdev_pad_config *cfg,
+			   struct v4l2_subdev_format *format)
+{
+	struct max9286_priv *priv = sd_to_max9286(sd);
+	struct v4l2_mbus_framefmt *cfg_fmt;
+
+	if (format->pad >= MAX9286_SRC_PAD)
+		return -EINVAL;
+
+	cfg_fmt = max9286_get_pad_format(priv, cfg, format->pad, format->which);
+	if (!cfg_fmt)
+		return -EINVAL;
+
+	format->format = *cfg_fmt;
+
+	return 0;
+}
+
+static const struct v4l2_subdev_video_ops max9286_video_ops = {
+	.s_stream	= max9286_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops max9286_pad_ops = {
+	.enum_mbus_code = max9286_enum_mbus_code,
+	.get_fmt	= max9286_get_fmt,
+	.set_fmt	= max9286_set_fmt,
+};
+
+static const struct v4l2_subdev_ops max9286_subdev_ops = {
+	.video		= &max9286_video_ops,
+	.pad		= &max9286_pad_ops,
+};
+
+static void max9286_init_format(struct v4l2_mbus_framefmt *fmt)
+{
+	fmt->width		= 1280;
+	fmt->height		= 800;
+	fmt->code		= MEDIA_BUS_FMT_UYVY8_2X8;
+	fmt->colorspace		= V4L2_COLORSPACE_SRGB;
+	fmt->field		= V4L2_FIELD_NONE;
+	fmt->ycbcr_enc		= V4L2_YCBCR_ENC_DEFAULT;
+	fmt->quantization	= V4L2_QUANTIZATION_DEFAULT;
+	fmt->xfer_func		= V4L2_XFER_FUNC_DEFAULT;
+}
+
+static int max9286_open(struct v4l2_subdev *subdev, struct v4l2_subdev_fh *fh)
+{
+	struct v4l2_mbus_framefmt *format;
+	unsigned int i;
+
+	for (i = 0; i < MAX9286_N_SINKS; i++) {
+		format = v4l2_subdev_get_try_format(subdev, fh->pad, i);
+		max9286_init_format(format);
+	}
+
+	return 0;
+}
+
+static const struct v4l2_subdev_internal_ops max9286_subdev_internal_ops = {
+	.open = max9286_open,
+};
+
+/* -----------------------------------------------------------------------------
+ * Probe/Remove
+ */
+
+static int max9286_setup(struct max9286_priv *priv)
+{
+	/*
+	 * Link ordering values for all enabled links combinations. Orders must
+	 * be assigned sequentially from 0 to the number of enabled links
+	 * without leaving any hole for disabled links. We thus assign orders to
+	 * enabled links first, and use the remaining order values for disabled
+	 * links are all links must have a different order value;
+	 */
+	static const u8 link_order[] = {
+		(3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xxxx */
+		(3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xxx0 */
+		(3 << 6) | (2 << 4) | (0 << 2) | (1 << 0), /* xx0x */
+		(3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xx10 */
+		(3 << 6) | (0 << 4) | (2 << 2) | (1 << 0), /* x0xx */
+		(3 << 6) | (1 << 4) | (2 << 2) | (0 << 0), /* x1x0 */
+		(3 << 6) | (1 << 4) | (0 << 2) | (2 << 0), /* x10x */
+		(3 << 6) | (1 << 4) | (1 << 2) | (0 << 0), /* x210 */
+		(0 << 6) | (3 << 4) | (2 << 2) | (1 << 0), /* 0xxx */
+		(1 << 6) | (3 << 4) | (2 << 2) | (0 << 0), /* 1xx0 */
+		(1 << 6) | (3 << 4) | (0 << 2) | (2 << 0), /* 1x0x */
+		(2 << 6) | (3 << 4) | (1 << 2) | (0 << 0), /* 2x10 */
+		(1 << 6) | (0 << 4) | (3 << 2) | (2 << 0), /* 10xx */
+		(2 << 6) | (1 << 4) | (3 << 2) | (0 << 0), /* 21x0 */
+		(2 << 6) | (1 << 4) | (0 << 2) | (3 << 0), /* 210x */
+		(3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* 3210 */
+	};
+
+	/*
+	 * Set the I2C bus speed.
+	 *
+	 * Enable I2C Local Acknowledge during the probe sequences of the camera
+	 * only. This should be disabled after the mux is initialised.
+	 */
+	max9286_configure_i2c(priv, true);
+
+	/*
+	 * Reverse channel setup.
+	 *
+	 * - Enable custom reverse channel configuration (through register 0x3f)
+	 *   and set the first pulse length to 35 clock cycles.
+	 * - Increase the reverse channel amplitude to 170mV to accommodate the
+	 *   high threshold enabled by the serializer driver.
+	 */
+	max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35));
+	max9286_write(priv, 0x3b, MAX9286_REV_TRF(1) | MAX9286_REV_AMP(70) |
+		      MAX9286_REV_AMP_X);
+
+	/*
+	 * Enable GMSL links, mask unused ones and autodetect link
+	 * used as CSI clock source.
+	 */
+	max9286_write(priv, 0x00, MAX9286_MSTLINKSEL_AUTO | priv->route_mask);
+	max9286_write(priv, 0x0b, link_order[priv->route_mask]);
+	max9286_write(priv, 0x69, (0xf & ~priv->route_mask));
+
+	/*
+	 * Video format setup:
+	 * Disable CSI output, VC is set accordingly to Link number.
+	 */
+	max9286_write(priv, 0x15, MAX9286_VCTYPE | MAX9286_0X15_RESV);
+
+	/* Enable CSI-2 Lane D0-D3 only, DBL mode, YUV422 8-bit. */
+	max9286_write(priv, 0x12, MAX9286_CSIDBL | MAX9286_DBL |
+		      MAX9286_CSILANECNT(priv->csi2_data_lanes) |
+		      MAX9286_DATATYPE_YUV422_8BIT);
+
+	/* Automatic: FRAMESYNC taken from the slowest Link. */
+	max9286_write(priv, 0x01, MAX9286_FSYNCMODE_INT_HIZ |
+		      MAX9286_FSYNCMETH_AUTO);
+
+	/* Enable HS/VS encoding, use D14/15 for HS/VS, invert VS. */
+	max9286_write(priv, 0x0c, MAX9286_HVEN | MAX9286_INVVS |
+		      MAX9286_HVSRC_D14);
+
+	/*
+	 * Wait for 2ms to allow the link to resynchronize after the
+	 * configuration change.
+	 */
+	usleep_range(2000, 5000);
+
+	return 0;
+}
+
+static const struct of_device_id max9286_dt_ids[] = {
+	{ .compatible = "maxim,max9286" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, max9286_dt_ids);
+
+static int max9286_init(struct device *dev)
+{
+	struct max9286_priv *priv;
+	struct i2c_client *client;
+	struct fwnode_handle *ep;
+	unsigned int i;
+	int ret;
+
+	/* Skip non-max9286 devices. */
+	if (!dev->of_node || !of_match_node(max9286_dt_ids, dev->of_node))
+		return 0;
+
+	client = to_i2c_client(dev);
+	priv = i2c_get_clientdata(client);
+
+	/* Enable the bus power. */
+	ret = regulator_enable(priv->regulator);
+	if (ret < 0) {
+		dev_err(&client->dev, "Unable to turn PoC on\n");
+		return ret;
+	}
+
+	priv->poc_enabled = true;
+
+	ret = max9286_setup(priv);
+	if (ret) {
+		dev_err(dev, "Unable to setup max9286\n");
+		goto err_regulator;
+	}
+
+	v4l2_i2c_subdev_init(&priv->sd, client, &max9286_subdev_ops);
+	priv->sd.internal_ops = &max9286_subdev_internal_ops;
+	priv->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+	v4l2_ctrl_handler_init(&priv->ctrls, 1);
+	/*
+	 * FIXME: Compute the real pixel rate. The 50 MP/s value comes from the
+	 * hardcoded frequency in the BSP CSI-2 receiver driver.
+	 */
+	v4l2_ctrl_new_std(&priv->ctrls, NULL, V4L2_CID_PIXEL_RATE,
+			  50000000, 50000000, 1, 50000000);
+	priv->sd.ctrl_handler = &priv->ctrls;
+	ret = priv->ctrls.error;
+	if (ret)
+		goto err_regulator;
+
+	priv->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+
+	priv->pads[MAX9286_SRC_PAD].flags = MEDIA_PAD_FL_SOURCE;
+	for (i = 0; i < MAX9286_SRC_PAD; i++)
+		priv->pads[i].flags = MEDIA_PAD_FL_SINK;
+	ret = media_entity_pads_init(&priv->sd.entity, MAX9286_N_PADS,
+				     priv->pads);
+	if (ret)
+		goto err_regulator;
+
+	ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), MAX9286_SRC_PAD,
+					     0, 0);
+	if (!ep) {
+		dev_err(dev, "Unable to retrieve endpoint on \"port@4\"\n");
+		ret = -ENOENT;
+		goto err_regulator;
+	}
+	priv->sd.fwnode = ep;
+
+	ret = v4l2_async_register_subdev(&priv->sd);
+	if (ret < 0) {
+		dev_err(dev, "Unable to register subdevice\n");
+		goto err_put_node;
+	}
+
+	ret = max9286_i2c_mux_init(priv);
+	if (ret) {
+		dev_err(dev, "Unable to initialize I2C multiplexer\n");
+		goto err_subdev_unregister;
+	}
+
+	/*
+	 * Re-configure I2C with local acknowledge disabled after cameras
+	 * have probed.
+	 */
+	max9286_configure_i2c(priv, false);
+
+	/* Leave the mux channels disabled until they are selected. */
+	max9286_i2c_mux_close(priv);
+
+	return 0;
+
+err_subdev_unregister:
+	v4l2_async_unregister_subdev(&priv->sd);
+	max9286_i2c_mux_close(priv);
+err_put_node:
+	fwnode_handle_put(ep);
+err_regulator:
+	regulator_disable(priv->regulator);
+	priv->poc_enabled = false;
+
+	return ret;
+}
+
+static struct device_node *max9286_get_i2c_by_id(struct device_node *parent,
+						 u32 id)
+{
+	struct device_node *child;
+
+	for_each_child_of_node(parent, child) {
+		u32 i2c_id = 0;
+
+		if (of_node_cmp(child->name, "i2c") != 0)
+			continue;
+		of_property_read_u32(child, "reg", &i2c_id);
+		if (id == i2c_id)
+			return child;
+	}
+
+	return NULL;
+}
+
+static int max9286_check_i2c_bus_by_id(struct device *dev, int id)
+{
+	struct device_node *i2c_np;
+
+	i2c_np = max9286_get_i2c_by_id(dev->of_node, id);
+	if (!i2c_np) {
+		dev_err(dev, "Failed to find corresponding i2c@%u\n", id);
+		return -ENODEV;
+	}
+
+	if (!of_device_is_available(i2c_np)) {
+		dev_dbg(dev, "Skipping port %u with disabled I2C bus\n", id);
+		of_node_put(i2c_np);
+		return -ENODEV;
+	}
+
+	of_node_put(i2c_np);
+
+	return 0;
+}
+
+static void max9286_cleanup_dt(struct max9286_priv *priv)
+{
+	struct max9286_source *source;
+
+	/*
+	 * Not strictly part of the DT, but the notifier is registered during
+	 * max9286_parse_dt(), and the notifier holds references to the fwnodes
+	 * thus the cleanup is here to mirror the registration.
+	 */
+	v4l2_async_notifier_unregister(&priv->notifier);
+	v4l2_async_notifier_cleanup(&priv->notifier);
+
+	for_each_source(priv, source) {
+		fwnode_handle_put(source->fwnode);
+		source->fwnode = NULL;
+	}
+}
+
+static int max9286_parse_dt(struct max9286_priv *priv)
+{
+	struct device *dev = &priv->client->dev;
+	struct device_node *ep_np = NULL;
+	int ret;
+
+	v4l2_async_notifier_init(&priv->notifier);
+
+	for_each_endpoint_of_node(dev->of_node, ep_np) {
+		struct max9286_source *source;
+		struct of_endpoint ep;
+
+		of_graph_parse_endpoint(ep_np, &ep);
+		dev_dbg(dev, "Endpoint %pOF on port %d",
+			ep.local_node, ep.port);
+
+		if (ep.port > MAX9286_NUM_GMSL) {
+			dev_err(dev, "Invalid endpoint %s on port %d",
+				of_node_full_name(ep.local_node), ep.port);
+			continue;
+		}
+
+		/* For the source endpoint just parse the bus configuration. */
+		if (ep.port == MAX9286_SRC_PAD) {
+			struct v4l2_fwnode_endpoint vep = { .bus_type = 0 };
+			int ret;
+
+			ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_np),
+							 &vep);
+			if (ret)
+				return ret;
+
+			if (vep.bus_type != V4L2_MBUS_CSI2_DPHY) {
+				dev_err(dev,
+					"Media bus %u type not supported\n",
+					vep.bus_type);
+				v4l2_fwnode_endpoint_free(&vep);
+				return -EINVAL;
+			}
+
+			priv->csi2_data_lanes =
+				vep.bus.mipi_csi2.num_data_lanes;
+			v4l2_fwnode_endpoint_free(&vep);
+
+			continue;
+		}
+
+		/* Skip if the corresponding GMSL link is unavailable. */
+		if (max9286_check_i2c_bus_by_id(dev, ep.port))
+			continue;
+
+		if (priv->sources[ep.port].fwnode) {
+			dev_err(dev,
+				"Multiple port endpoints are not supported: %d",
+				ep.port);
+
+			continue;
+		}
+
+		source = &priv->sources[ep.port];
+		source->fwnode = fwnode_graph_get_remote_endpoint(
+						of_fwnode_handle(ep_np));
+		if (!source->fwnode) {
+			dev_err(dev,
+				"Endpoint %pOF has no remote endpoint connection\n",
+				ep.local_node);
+
+			continue;
+		}
+
+		source->asd.match_type = V4L2_ASYNC_MATCH_FWNODE;
+		source->asd.match.fwnode = source->fwnode;
+
+		ret = v4l2_async_notifier_add_subdev(&priv->notifier,
+						     &source->asd);
+		if (ret) {
+			v4l2_async_notifier_cleanup(&priv->notifier);
+			return ret;
+		}
+
+		priv->source_mask |= BIT(ep.port);
+		priv->nsources++;
+	}
+
+	/* Do not register the subdev notifier if there are no devices. */
+	if (!priv->nsources)
+		return 0;
+
+	priv->route_mask = priv->source_mask;
+	priv->notifier.ops = &max9286_notify_ops;
+
+	ret = v4l2_async_subdev_notifier_register(&priv->sd, &priv->notifier);
+	if (ret)
+		v4l2_async_notifier_cleanup(&priv->notifier);
+
+	return 0;
+}
+
+static int max9286_probe(struct i2c_client *client,
+			 const struct i2c_device_id *did)
+{
+	struct max9286_priv *priv;
+	unsigned int i;
+	int ret;
+
+	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->client = client;
+	i2c_set_clientdata(client, priv);
+
+	for (i = 0; i < MAX9286_N_SINKS; i++)
+		max9286_init_format(&priv->fmt[i]);
+
+	ret = max9286_parse_dt(priv);
+	if (ret)
+		return ret;
+
+	priv->regulator = regulator_get(&client->dev, "poc");
+	if (IS_ERR(priv->regulator)) {
+		if (PTR_ERR(priv->regulator) != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"Unable to get PoC regulator (%ld)\n",
+				PTR_ERR(priv->regulator));
+		ret = PTR_ERR(priv->regulator);
+		goto err_free;
+	}
+
+	/*
+	 * We can have multiple MAX9286 instances on the same physical I2C
+	 * bus, and I2C children behind ports of separate MAX9286 instances
+	 * having the same I2C address. As the MAX9286 starts by default with
+	 * all ports enabled, we need to disable all ports on all MAX9286
+	 * instances before proceeding to further initialize the devices and
+	 * instantiate children.
+	 *
+	 * Start by just disabling all channels on the current device. Then,
+	 * if all other MAX9286 on the parent bus have been probed, proceed
+	 * to initialize them all, including the current one.
+	 */
+	max9286_i2c_mux_close(priv);
+
+	/*
+	 * The MAX9286 initialises with auto-acknowledge enabled by default.
+	 * This means that if multiple MAX9286 devices are connected to an I2C
+	 * bus, another MAX9286 could ack I2C transfers meant for a device on
+	 * the other side of the GMSL links for this MAX9286 (such as a
+	 * MAX9271). To prevent that disable auto-acknowledge early on; it
+	 * will be enabled later as needed.
+	 */
+	max9286_configure_i2c(priv, false);
+
+	ret = max9286_init(&client->dev);
+	if (ret < 0)
+		goto err_regulator;
+
+	return 0;
+
+err_regulator:
+	regulator_put(priv->regulator);
+	max9286_i2c_mux_close(priv);
+	max9286_configure_i2c(priv, false);
+err_free:
+	max9286_cleanup_dt(priv);
+	kfree(priv);
+
+	return ret;
+}
+
+static int max9286_remove(struct i2c_client *client)
+{
+	struct max9286_priv *priv = i2c_get_clientdata(client);
+
+	i2c_mux_del_adapters(priv->mux);
+
+	fwnode_handle_put(priv->sd.fwnode);
+	v4l2_async_unregister_subdev(&priv->sd);
+
+	if (priv->poc_enabled)
+		regulator_disable(priv->regulator);
+	regulator_put(priv->regulator);
+
+	max9286_cleanup_dt(priv);
+	kfree(priv);
+
+	return 0;
+}
+
+static const struct i2c_device_id max9286_id[] = {
+	{ "max9286", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, max9286_id);
+
+static struct i2c_driver max9286_i2c_driver = {
+	.driver	= {
+		.name		= "max9286",
+		.of_match_table	= of_match_ptr(max9286_dt_ids),
+	},
+	.probe		= max9286_probe,
+	.remove		= max9286_remove,
+	.id_table	= max9286_id,
+};
+
+module_i2c_driver(max9286_i2c_driver);
+
+MODULE_DESCRIPTION("Maxim MAX9286 GMSL Deserializer Driver");
+MODULE_AUTHOR("Jacopo Mondi, Kieran Bingham, Laurent Pinchart, Niklas Söderlund, Vladimir Barinov");
+MODULE_LICENSE("GPL");