| Message ID | 20190820151934.3860-3-megous@megous.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add basic support for RTC on Allwinner H6 SoC | expand |
On 20/08/2019 17:19:33+0200, megous@megous.com wrote: > From: Ondrej Jirman <megous@megous.com> > > RTC on H6 is mostly the same as on H5 and H3. It has slight differences > mostly in features that are not yet supported by this driver. > > Some differences are already stated in the comments in existing code. > One other difference is that H6 has extra bit in LOSC_CTRL_REG, called > EXT_LOSC_EN to enable/disable external low speed crystal oscillator. > > It also has bit EXT_LOSC_STA in LOSC_AUTO_SWT_STA_REG, to check whether > external low speed oscillator is working correctly. > > This patch adds support for enabling LOSC when necessary: > > - during reparenting > - when probing the clock > > H6 also has capacbility to automatically reparent RTC clock from > external crystal oscillator, to internal RC oscillator, if external > oscillator fails. This is enabled by default. Disable it during > probe. > > Signed-off-by: Ondrej Jirman <megous@megous.com> > Reviewed-by: Chen-Yu Tsai <wens@csie.org> > --- > drivers/rtc/rtc-sun6i.c | 40 ++++++++++++++++++++++++++++++++++++++-- > 1 file changed, 38 insertions(+), 2 deletions(-) > Applied, thanks.
Hi! Dne torek, 20. avgust 2019 ob 17:19:33 CEST je megous@megous.com napisal(a): > From: Ondrej Jirman <megous@megous.com> > > RTC on H6 is mostly the same as on H5 and H3. It has slight differences > mostly in features that are not yet supported by this driver. > > Some differences are already stated in the comments in existing code. > One other difference is that H6 has extra bit in LOSC_CTRL_REG, called > EXT_LOSC_EN to enable/disable external low speed crystal oscillator. > > It also has bit EXT_LOSC_STA in LOSC_AUTO_SWT_STA_REG, to check whether > external low speed oscillator is working correctly. > > This patch adds support for enabling LOSC when necessary: > > - during reparenting > - when probing the clock > > H6 also has capacbility to automatically reparent RTC clock from > external crystal oscillator, to internal RC oscillator, if external > oscillator fails. This is enabled by default. Disable it during > probe. > > Signed-off-by: Ondrej Jirman <megous@megous.com> > Reviewed-by: Chen-Yu Tsai <wens@csie.org> > --- > drivers/rtc/rtc-sun6i.c | 40 ++++++++++++++++++++++++++++++++++++++-- > 1 file changed, 38 insertions(+), 2 deletions(-) > > diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c > index d50ee023b559..b0c3752bed3f 100644 > --- a/drivers/rtc/rtc-sun6i.c > +++ b/drivers/rtc/rtc-sun6i.c > @@ -32,9 +32,11 @@ > /* Control register */ > #define SUN6I_LOSC_CTRL 0x0000 > #define SUN6I_LOSC_CTRL_KEY (0x16aa << 16) > +#define SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS BIT(15) User manual says that above field is bit 14. Best regards, Jernej > #define SUN6I_LOSC_CTRL_ALM_DHMS_ACC BIT(9) > #define SUN6I_LOSC_CTRL_RTC_HMS_ACC BIT(8) > #define SUN6I_LOSC_CTRL_RTC_YMD_ACC BIT(7) > +#define SUN6I_LOSC_CTRL_EXT_LOSC_EN BIT(4) > #define SUN6I_LOSC_CTRL_EXT_OSC BIT(0) > #define SUN6I_LOSC_CTRL_ACC_MASK GENMASK(9, 7) > > @@ -128,6 +130,8 @@ struct sun6i_rtc_clk_data { > unsigned int has_prescaler : 1; > unsigned int has_out_clk : 1; > unsigned int export_iosc : 1; > + unsigned int has_losc_en : 1; > + unsigned int has_auto_swt : 1; > }; > > struct sun6i_rtc_dev { > @@ -190,6 +194,10 @@ static int sun6i_rtc_osc_set_parent(struct clk_hw *hw, > u8 index) val &= ~SUN6I_LOSC_CTRL_EXT_OSC; > val |= SUN6I_LOSC_CTRL_KEY; > val |= index ? SUN6I_LOSC_CTRL_EXT_OSC : 0; > + if (rtc->data->has_losc_en) { > + val &= ~SUN6I_LOSC_CTRL_EXT_LOSC_EN; > + val |= index ? SUN6I_LOSC_CTRL_EXT_LOSC_EN : 0; > + } > writel(val, rtc->base + SUN6I_LOSC_CTRL); > spin_unlock_irqrestore(&rtc->lock, flags); > > @@ -215,6 +223,7 @@ static void __init sun6i_rtc_clk_init(struct device_node > *node, const char *iosc_name = "rtc-int-osc"; > const char *clkout_name = "osc32k-out"; > const char *parents[2]; > + u32 reg; > > rtc = kzalloc(sizeof(*rtc), GFP_KERNEL); > if (!rtc) > @@ -235,9 +244,18 @@ static void __init sun6i_rtc_clk_init(struct > device_node *node, goto err; > } > > + reg = SUN6I_LOSC_CTRL_KEY; > + if (rtc->data->has_auto_swt) { > + /* Bypass auto-switch to int osc, on ext losc failure */ > + reg |= SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS; > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > + } > + > /* Switch to the external, more precise, oscillator */ > - writel(SUN6I_LOSC_CTRL_KEY | SUN6I_LOSC_CTRL_EXT_OSC, > - rtc->base + SUN6I_LOSC_CTRL); > + reg |= SUN6I_LOSC_CTRL_EXT_OSC; > + if (rtc->data->has_losc_en) > + reg |= SUN6I_LOSC_CTRL_EXT_LOSC_EN; > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > /* Yes, I know, this is ugly. */ > sun6i_rtc = rtc; > @@ -345,6 +363,23 @@ CLK_OF_DECLARE_DRIVER(sun8i_h3_rtc_clk, > "allwinner,sun8i-h3-rtc", CLK_OF_DECLARE_DRIVER(sun50i_h5_rtc_clk, > "allwinner,sun50i-h5-rtc", sun8i_h3_rtc_clk_init); > > +static const struct sun6i_rtc_clk_data sun50i_h6_rtc_data = { > + .rc_osc_rate = 16000000, > + .fixed_prescaler = 32, > + .has_prescaler = 1, > + .has_out_clk = 1, > + .export_iosc = 1, > + .has_losc_en = 1, > + .has_auto_swt = 1, > +}; > + > +static void __init sun50i_h6_rtc_clk_init(struct device_node *node) > +{ > + sun6i_rtc_clk_init(node, &sun50i_h6_rtc_data); > +} > +CLK_OF_DECLARE_DRIVER(sun50i_h6_rtc_clk, "allwinner,sun50i-h6-rtc", > + sun50i_h6_rtc_clk_init); > + > static const struct sun6i_rtc_clk_data sun8i_v3_rtc_data = { > .rc_osc_rate = 32000, > .has_out_clk = 1, > @@ -675,6 +710,7 @@ static const struct of_device_id sun6i_rtc_dt_ids[] = { > { .compatible = "allwinner,sun8i-r40-rtc" }, > { .compatible = "allwinner,sun8i-v3-rtc" }, > { .compatible = "allwinner,sun50i-h5-rtc" }, > + { .compatible = "allwinner,sun50i-h6-rtc" }, > { /* sentinel */ }, > }; > MODULE_DEVICE_TABLE(of, sun6i_rtc_dt_ids);
Hi, On Sat, Aug 24, 2019 at 02:32:32PM +0200, Jernej Škrabec wrote: > Hi! > > Dne torek, 20. avgust 2019 ob 17:19:33 CEST je megous@megous.com napisal(a): > > From: Ondrej Jirman <megous@megous.com> > > > > RTC on H6 is mostly the same as on H5 and H3. It has slight differences > > mostly in features that are not yet supported by this driver. > > > > Some differences are already stated in the comments in existing code. > > One other difference is that H6 has extra bit in LOSC_CTRL_REG, called > > EXT_LOSC_EN to enable/disable external low speed crystal oscillator. > > > > It also has bit EXT_LOSC_STA in LOSC_AUTO_SWT_STA_REG, to check whether > > external low speed oscillator is working correctly. > > > > This patch adds support for enabling LOSC when necessary: > > > > - during reparenting > > - when probing the clock > > > > H6 also has capacbility to automatically reparent RTC clock from > > external crystal oscillator, to internal RC oscillator, if external > > oscillator fails. This is enabled by default. Disable it during > > probe. > > > > Signed-off-by: Ondrej Jirman <megous@megous.com> > > Reviewed-by: Chen-Yu Tsai <wens@csie.org> > > --- > > drivers/rtc/rtc-sun6i.c | 40 ++++++++++++++++++++++++++++++++++++++-- > > 1 file changed, 38 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c > > index d50ee023b559..b0c3752bed3f 100644 > > --- a/drivers/rtc/rtc-sun6i.c > > +++ b/drivers/rtc/rtc-sun6i.c > > @@ -32,9 +32,11 @@ > > /* Control register */ > > #define SUN6I_LOSC_CTRL 0x0000 > > #define SUN6I_LOSC_CTRL_KEY (0x16aa << 16) > > +#define SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS BIT(15) > > User manual says that above field is bit 14. See the previous discussion, this is from BSP. regards, o. > Best regards, > Jernej > > > #define SUN6I_LOSC_CTRL_ALM_DHMS_ACC BIT(9) > > #define SUN6I_LOSC_CTRL_RTC_HMS_ACC BIT(8) > > #define SUN6I_LOSC_CTRL_RTC_YMD_ACC BIT(7) > > +#define SUN6I_LOSC_CTRL_EXT_LOSC_EN BIT(4) > > #define SUN6I_LOSC_CTRL_EXT_OSC BIT(0) > > #define SUN6I_LOSC_CTRL_ACC_MASK GENMASK(9, 7) > > > > @@ -128,6 +130,8 @@ struct sun6i_rtc_clk_data { > > unsigned int has_prescaler : 1; > > unsigned int has_out_clk : 1; > > unsigned int export_iosc : 1; > > + unsigned int has_losc_en : 1; > > + unsigned int has_auto_swt : 1; > > }; > > > > struct sun6i_rtc_dev { > > @@ -190,6 +194,10 @@ static int sun6i_rtc_osc_set_parent(struct clk_hw *hw, > > u8 index) val &= ~SUN6I_LOSC_CTRL_EXT_OSC; > > val |= SUN6I_LOSC_CTRL_KEY; > > val |= index ? SUN6I_LOSC_CTRL_EXT_OSC : 0; > > + if (rtc->data->has_losc_en) { > > + val &= ~SUN6I_LOSC_CTRL_EXT_LOSC_EN; > > + val |= index ? SUN6I_LOSC_CTRL_EXT_LOSC_EN : 0; > > + } > > writel(val, rtc->base + SUN6I_LOSC_CTRL); > > spin_unlock_irqrestore(&rtc->lock, flags); > > > > @@ -215,6 +223,7 @@ static void __init sun6i_rtc_clk_init(struct device_node > > *node, const char *iosc_name = "rtc-int-osc"; > > const char *clkout_name = "osc32k-out"; > > const char *parents[2]; > > + u32 reg; > > > > rtc = kzalloc(sizeof(*rtc), GFP_KERNEL); > > if (!rtc) > > @@ -235,9 +244,18 @@ static void __init sun6i_rtc_clk_init(struct > > device_node *node, goto err; > > } > > > > + reg = SUN6I_LOSC_CTRL_KEY; > > + if (rtc->data->has_auto_swt) { > > + /* Bypass auto-switch to int osc, on ext losc failure */ > > + reg |= SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS; > > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > + } > > + > > /* Switch to the external, more precise, oscillator */ > > - writel(SUN6I_LOSC_CTRL_KEY | SUN6I_LOSC_CTRL_EXT_OSC, > > - rtc->base + SUN6I_LOSC_CTRL); > > + reg |= SUN6I_LOSC_CTRL_EXT_OSC; > > + if (rtc->data->has_losc_en) > > + reg |= SUN6I_LOSC_CTRL_EXT_LOSC_EN; > > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > > > /* Yes, I know, this is ugly. */ > > sun6i_rtc = rtc; > > @@ -345,6 +363,23 @@ CLK_OF_DECLARE_DRIVER(sun8i_h3_rtc_clk, > > "allwinner,sun8i-h3-rtc", CLK_OF_DECLARE_DRIVER(sun50i_h5_rtc_clk, > > "allwinner,sun50i-h5-rtc", sun8i_h3_rtc_clk_init); > > > > +static const struct sun6i_rtc_clk_data sun50i_h6_rtc_data = { > > + .rc_osc_rate = 16000000, > > + .fixed_prescaler = 32, > > + .has_prescaler = 1, > > + .has_out_clk = 1, > > + .export_iosc = 1, > > + .has_losc_en = 1, > > + .has_auto_swt = 1, > > +}; > > + > > +static void __init sun50i_h6_rtc_clk_init(struct device_node *node) > > +{ > > + sun6i_rtc_clk_init(node, &sun50i_h6_rtc_data); > > +} > > +CLK_OF_DECLARE_DRIVER(sun50i_h6_rtc_clk, "allwinner,sun50i-h6-rtc", > > + sun50i_h6_rtc_clk_init); > > + > > static const struct sun6i_rtc_clk_data sun8i_v3_rtc_data = { > > .rc_osc_rate = 32000, > > .has_out_clk = 1, > > @@ -675,6 +710,7 @@ static const struct of_device_id sun6i_rtc_dt_ids[] = { > > { .compatible = "allwinner,sun8i-r40-rtc" }, > > { .compatible = "allwinner,sun8i-v3-rtc" }, > > { .compatible = "allwinner,sun50i-h5-rtc" }, > > + { .compatible = "allwinner,sun50i-h6-rtc" }, > > { /* sentinel */ }, > > }; > > MODULE_DEVICE_TABLE(of, sun6i_rtc_dt_ids); > > > > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Dne sobota, 24. avgust 2019 ob 14:46:54 CEST je Ondřej Jirman napisal(a): > Hi, > > On Sat, Aug 24, 2019 at 02:32:32PM +0200, Jernej Škrabec wrote: > > Hi! > > > > Dne torek, 20. avgust 2019 ob 17:19:33 CEST je megous@megous.com napisal(a): > > > From: Ondrej Jirman <megous@megous.com> > > > > > > RTC on H6 is mostly the same as on H5 and H3. It has slight differences > > > mostly in features that are not yet supported by this driver. > > > > > > Some differences are already stated in the comments in existing code. > > > One other difference is that H6 has extra bit in LOSC_CTRL_REG, called > > > EXT_LOSC_EN to enable/disable external low speed crystal oscillator. > > > > > > It also has bit EXT_LOSC_STA in LOSC_AUTO_SWT_STA_REG, to check whether > > > external low speed oscillator is working correctly. > > > > > > This patch adds support for enabling LOSC when necessary: > > > > > > - during reparenting > > > - when probing the clock > > > > > > H6 also has capacbility to automatically reparent RTC clock from > > > external crystal oscillator, to internal RC oscillator, if external > > > oscillator fails. This is enabled by default. Disable it during > > > probe. > > > > > > Signed-off-by: Ondrej Jirman <megous@megous.com> > > > Reviewed-by: Chen-Yu Tsai <wens@csie.org> > > > --- > > > > > > drivers/rtc/rtc-sun6i.c | 40 ++++++++++++++++++++++++++++++++++++++-- > > > 1 file changed, 38 insertions(+), 2 deletions(-) > > > > > > diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c > > > index d50ee023b559..b0c3752bed3f 100644 > > > --- a/drivers/rtc/rtc-sun6i.c > > > +++ b/drivers/rtc/rtc-sun6i.c > > > @@ -32,9 +32,11 @@ > > > > > > /* Control register */ > > > #define SUN6I_LOSC_CTRL 0x0000 > > > #define SUN6I_LOSC_CTRL_KEY (0x16aa << 16) > > > > > > +#define SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS BIT(15) > > > > User manual says that above field is bit 14. > > See the previous discussion, this is from BSP. I have two versions of BSP (don't ask me which) which have this set as bit 14 and changing this to 14 actually solves all my problems with LOSC (no more issues with setting RTC and HDMI-CEC works now - it uses LOSC as parent) on Tanix TX6 box. Best regards, Jernej > > regards, > o. > > > Best regards, > > Jernej > > > > > #define SUN6I_LOSC_CTRL_ALM_DHMS_ACC BIT(9) > > > #define SUN6I_LOSC_CTRL_RTC_HMS_ACC BIT(8) > > > #define SUN6I_LOSC_CTRL_RTC_YMD_ACC BIT(7) > > > > > > +#define SUN6I_LOSC_CTRL_EXT_LOSC_EN BIT(4) > > > > > > #define SUN6I_LOSC_CTRL_EXT_OSC BIT(0) > > > #define SUN6I_LOSC_CTRL_ACC_MASK GENMASK(9, 7) > > > > > > @@ -128,6 +130,8 @@ struct sun6i_rtc_clk_data { > > > > > > unsigned int has_prescaler : 1; > > > unsigned int has_out_clk : 1; > > > unsigned int export_iosc : 1; > > > > > > + unsigned int has_losc_en : 1; > > > + unsigned int has_auto_swt : 1; > > > > > > }; > > > > > > struct sun6i_rtc_dev { > > > > > > @@ -190,6 +194,10 @@ static int sun6i_rtc_osc_set_parent(struct clk_hw > > > *hw, > > > u8 index) val &= ~SUN6I_LOSC_CTRL_EXT_OSC; > > > > > > val |= SUN6I_LOSC_CTRL_KEY; > > > val |= index ? SUN6I_LOSC_CTRL_EXT_OSC : 0; > > > > > > + if (rtc->data->has_losc_en) { > > > + val &= ~SUN6I_LOSC_CTRL_EXT_LOSC_EN; > > > + val |= index ? SUN6I_LOSC_CTRL_EXT_LOSC_EN : 0; > > > + } > > > > > > writel(val, rtc->base + SUN6I_LOSC_CTRL); > > > spin_unlock_irqrestore(&rtc->lock, flags); > > > > > > @@ -215,6 +223,7 @@ static void __init sun6i_rtc_clk_init(struct > > > device_node *node, const char *iosc_name = "rtc-int-osc"; > > > > > > const char *clkout_name = "osc32k-out"; > > > const char *parents[2]; > > > > > > + u32 reg; > > > > > > rtc = kzalloc(sizeof(*rtc), GFP_KERNEL); > > > if (!rtc) > > > > > > @@ -235,9 +244,18 @@ static void __init sun6i_rtc_clk_init(struct > > > device_node *node, goto err; > > > > > > } > > > > > > + reg = SUN6I_LOSC_CTRL_KEY; > > > + if (rtc->data->has_auto_swt) { > > > + /* Bypass auto-switch to int osc, on ext losc failure */ > > > + reg |= SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS; > > > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > > + } > > > + > > > > > > /* Switch to the external, more precise, oscillator */ > > > > > > - writel(SUN6I_LOSC_CTRL_KEY | SUN6I_LOSC_CTRL_EXT_OSC, > > > - rtc->base + SUN6I_LOSC_CTRL); > > > + reg |= SUN6I_LOSC_CTRL_EXT_OSC; > > > + if (rtc->data->has_losc_en) > > > + reg |= SUN6I_LOSC_CTRL_EXT_LOSC_EN; > > > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > > > > > /* Yes, I know, this is ugly. */ > > > sun6i_rtc = rtc; > > > > > > @@ -345,6 +363,23 @@ CLK_OF_DECLARE_DRIVER(sun8i_h3_rtc_clk, > > > "allwinner,sun8i-h3-rtc", CLK_OF_DECLARE_DRIVER(sun50i_h5_rtc_clk, > > > "allwinner,sun50i-h5-rtc", sun8i_h3_rtc_clk_init); > > > > > > +static const struct sun6i_rtc_clk_data sun50i_h6_rtc_data = { > > > + .rc_osc_rate = 16000000, > > > + .fixed_prescaler = 32, > > > + .has_prescaler = 1, > > > + .has_out_clk = 1, > > > + .export_iosc = 1, > > > + .has_losc_en = 1, > > > + .has_auto_swt = 1, > > > +}; > > > + > > > +static void __init sun50i_h6_rtc_clk_init(struct device_node *node) > > > +{ > > > + sun6i_rtc_clk_init(node, &sun50i_h6_rtc_data); > > > +} > > > +CLK_OF_DECLARE_DRIVER(sun50i_h6_rtc_clk, "allwinner,sun50i-h6-rtc", > > > + sun50i_h6_rtc_clk_init); > > > + > > > > > > static const struct sun6i_rtc_clk_data sun8i_v3_rtc_data = { > > > > > > .rc_osc_rate = 32000, > > > .has_out_clk = 1, > > > > > > @@ -675,6 +710,7 @@ static const struct of_device_id sun6i_rtc_dt_ids[] > > > = { > > > > > > { .compatible = "allwinner,sun8i-r40-rtc" }, > > > { .compatible = "allwinner,sun8i-v3-rtc" }, > > > { .compatible = "allwinner,sun50i-h5-rtc" }, > > > > > > + { .compatible = "allwinner,sun50i-h6-rtc" }, > > > > > > { /* sentinel */ }, > > > > > > }; > > > MODULE_DEVICE_TABLE(of, sun6i_rtc_dt_ids); > > > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel@lists.infradead.org > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Sat, Aug 24, 2019 at 02:51:54PM +0200, Jernej Škrabec wrote: > Dne sobota, 24. avgust 2019 ob 14:46:54 CEST je Ondřej Jirman napisal(a): > > Hi, > > > > On Sat, Aug 24, 2019 at 02:32:32PM +0200, Jernej Škrabec wrote: > > > Hi! > > > > > > Dne torek, 20. avgust 2019 ob 17:19:33 CEST je megous@megous.com > napisal(a): > > > > From: Ondrej Jirman <megous@megous.com> > > > > > > > > RTC on H6 is mostly the same as on H5 and H3. It has slight differences > > > > mostly in features that are not yet supported by this driver. > > > > > > > > Some differences are already stated in the comments in existing code. > > > > One other difference is that H6 has extra bit in LOSC_CTRL_REG, called > > > > EXT_LOSC_EN to enable/disable external low speed crystal oscillator. > > > > > > > > It also has bit EXT_LOSC_STA in LOSC_AUTO_SWT_STA_REG, to check whether > > > > external low speed oscillator is working correctly. > > > > > > > > This patch adds support for enabling LOSC when necessary: > > > > > > > > - during reparenting > > > > - when probing the clock > > > > > > > > H6 also has capacbility to automatically reparent RTC clock from > > > > external crystal oscillator, to internal RC oscillator, if external > > > > oscillator fails. This is enabled by default. Disable it during > > > > probe. > > > > > > > > Signed-off-by: Ondrej Jirman <megous@megous.com> > > > > Reviewed-by: Chen-Yu Tsai <wens@csie.org> > > > > --- > > > > > > > > drivers/rtc/rtc-sun6i.c | 40 ++++++++++++++++++++++++++++++++++++++-- > > > > 1 file changed, 38 insertions(+), 2 deletions(-) > > > > > > > > diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c > > > > index d50ee023b559..b0c3752bed3f 100644 > > > > --- a/drivers/rtc/rtc-sun6i.c > > > > +++ b/drivers/rtc/rtc-sun6i.c > > > > @@ -32,9 +32,11 @@ > > > > > > > > /* Control register */ > > > > #define SUN6I_LOSC_CTRL 0x0000 > > > > #define SUN6I_LOSC_CTRL_KEY (0x16aa << 16) > > > > > > > > +#define SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS BIT(15) > > > > > > User manual says that above field is bit 14. > > > > See the previous discussion, this is from BSP. > > I have two versions of BSP (don't ask me which) which have this set as bit 14 > and changing this to 14 actually solves all my problems with LOSC (no more > issues with setting RTC and HDMI-CEC works now - it uses LOSC as parent) on > Tanix TX6 box. Interesting. Is LOSC fed externally generated clock, or is it setup as a crystal oscillator on your board? Anyway, see here: https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.h?h=h6-4.9-bsp#n649 https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n652 It would be nice to know what's really happening. My output is: [ 0.832252] sun6i-rtc 7000000.rtc: registered as rtc0 [ 0.832257] sun6i-rtc 7000000.rtc: RTC enabled [ 1.728968] sun6i-rtc 7000000.rtc: setting system clock to 1970-01-01T00:00:07 UTC (7) I think, you may have just enabled the auto switch feature, and running the clock from low precision RC oscillator with your patch. The real issue probably is that the mainline driver is missing this: https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n650 regards, o. > Best regards, > Jernej > > > > > regards, > > o. > > > > > Best regards, > > > Jernej > > > > > > > #define SUN6I_LOSC_CTRL_ALM_DHMS_ACC BIT(9) > > > > #define SUN6I_LOSC_CTRL_RTC_HMS_ACC BIT(8) > > > > #define SUN6I_LOSC_CTRL_RTC_YMD_ACC BIT(7) > > > > > > > > +#define SUN6I_LOSC_CTRL_EXT_LOSC_EN BIT(4) > > > > > > > > #define SUN6I_LOSC_CTRL_EXT_OSC BIT(0) > > > > #define SUN6I_LOSC_CTRL_ACC_MASK GENMASK(9, 7) > > > > > > > > @@ -128,6 +130,8 @@ struct sun6i_rtc_clk_data { > > > > > > > > unsigned int has_prescaler : 1; > > > > unsigned int has_out_clk : 1; > > > > unsigned int export_iosc : 1; > > > > > > > > + unsigned int has_losc_en : 1; > > > > + unsigned int has_auto_swt : 1; > > > > > > > > }; > > > > > > > > struct sun6i_rtc_dev { > > > > > > > > @@ -190,6 +194,10 @@ static int sun6i_rtc_osc_set_parent(struct clk_hw > > > > *hw, > > > > u8 index) val &= ~SUN6I_LOSC_CTRL_EXT_OSC; > > > > > > > > val |= SUN6I_LOSC_CTRL_KEY; > > > > val |= index ? SUN6I_LOSC_CTRL_EXT_OSC : 0; > > > > > > > > + if (rtc->data->has_losc_en) { > > > > + val &= ~SUN6I_LOSC_CTRL_EXT_LOSC_EN; > > > > + val |= index ? SUN6I_LOSC_CTRL_EXT_LOSC_EN : 0; > > > > + } > > > > > > > > writel(val, rtc->base + SUN6I_LOSC_CTRL); > > > > spin_unlock_irqrestore(&rtc->lock, flags); > > > > > > > > @@ -215,6 +223,7 @@ static void __init sun6i_rtc_clk_init(struct > > > > device_node *node, const char *iosc_name = "rtc-int-osc"; > > > > > > > > const char *clkout_name = "osc32k-out"; > > > > const char *parents[2]; > > > > > > > > + u32 reg; > > > > > > > > rtc = kzalloc(sizeof(*rtc), GFP_KERNEL); > > > > if (!rtc) > > > > > > > > @@ -235,9 +244,18 @@ static void __init sun6i_rtc_clk_init(struct > > > > device_node *node, goto err; > > > > > > > > } > > > > > > > > + reg = SUN6I_LOSC_CTRL_KEY; > > > > + if (rtc->data->has_auto_swt) { > > > > + /* Bypass auto-switch to int osc, on ext losc failure > */ > > > > + reg |= SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS; > > > > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > > > + } > > > > + > > > > > > > > /* Switch to the external, more precise, oscillator */ > > > > > > > > - writel(SUN6I_LOSC_CTRL_KEY | SUN6I_LOSC_CTRL_EXT_OSC, > > > > - rtc->base + SUN6I_LOSC_CTRL); > > > > + reg |= SUN6I_LOSC_CTRL_EXT_OSC; > > > > + if (rtc->data->has_losc_en) > > > > + reg |= SUN6I_LOSC_CTRL_EXT_LOSC_EN; > > > > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > > > > > > > /* Yes, I know, this is ugly. */ > > > > sun6i_rtc = rtc; > > > > > > > > @@ -345,6 +363,23 @@ CLK_OF_DECLARE_DRIVER(sun8i_h3_rtc_clk, > > > > "allwinner,sun8i-h3-rtc", CLK_OF_DECLARE_DRIVER(sun50i_h5_rtc_clk, > > > > "allwinner,sun50i-h5-rtc", sun8i_h3_rtc_clk_init); > > > > > > > > +static const struct sun6i_rtc_clk_data sun50i_h6_rtc_data = { > > > > + .rc_osc_rate = 16000000, > > > > + .fixed_prescaler = 32, > > > > + .has_prescaler = 1, > > > > + .has_out_clk = 1, > > > > + .export_iosc = 1, > > > > + .has_losc_en = 1, > > > > + .has_auto_swt = 1, > > > > +}; > > > > + > > > > +static void __init sun50i_h6_rtc_clk_init(struct device_node *node) > > > > +{ > > > > + sun6i_rtc_clk_init(node, &sun50i_h6_rtc_data); > > > > +} > > > > +CLK_OF_DECLARE_DRIVER(sun50i_h6_rtc_clk, "allwinner,sun50i-h6-rtc", > > > > + sun50i_h6_rtc_clk_init); > > > > + > > > > > > > > static const struct sun6i_rtc_clk_data sun8i_v3_rtc_data = { > > > > > > > > .rc_osc_rate = 32000, > > > > .has_out_clk = 1, > > > > > > > > @@ -675,6 +710,7 @@ static const struct of_device_id sun6i_rtc_dt_ids[] > > > > = { > > > > > > > > { .compatible = "allwinner,sun8i-r40-rtc" }, > > > > { .compatible = "allwinner,sun8i-v3-rtc" }, > > > > { .compatible = "allwinner,sun50i-h5-rtc" }, > > > > > > > > + { .compatible = "allwinner,sun50i-h6-rtc" }, > > > > > > > > { /* sentinel */ }, > > > > > > > > }; > > > > MODULE_DEVICE_TABLE(of, sun6i_rtc_dt_ids); > > > > > > _______________________________________________ > > > linux-arm-kernel mailing list > > > linux-arm-kernel@lists.infradead.org > > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel > > > > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Dne sobota, 24. avgust 2019 ob 15:05:44 CEST je Ondřej Jirman napisal(a): > On Sat, Aug 24, 2019 at 02:51:54PM +0200, Jernej Škrabec wrote: > > Dne sobota, 24. avgust 2019 ob 14:46:54 CEST je Ondřej Jirman napisal(a): > > > Hi, > > > > > > On Sat, Aug 24, 2019 at 02:32:32PM +0200, Jernej Škrabec wrote: > > > > Hi! > > > > > > > > Dne torek, 20. avgust 2019 ob 17:19:33 CEST je megous@megous.com > > > > napisal(a): > > > > > From: Ondrej Jirman <megous@megous.com> > > > > > > > > > > RTC on H6 is mostly the same as on H5 and H3. It has slight > > > > > differences > > > > > mostly in features that are not yet supported by this driver. > > > > > > > > > > Some differences are already stated in the comments in existing > > > > > code. > > > > > One other difference is that H6 has extra bit in LOSC_CTRL_REG, > > > > > called > > > > > EXT_LOSC_EN to enable/disable external low speed crystal oscillator. > > > > > > > > > > It also has bit EXT_LOSC_STA in LOSC_AUTO_SWT_STA_REG, to check > > > > > whether > > > > > external low speed oscillator is working correctly. > > > > > > > > > > This patch adds support for enabling LOSC when necessary: > > > > > > > > > > - during reparenting > > > > > - when probing the clock > > > > > > > > > > H6 also has capacbility to automatically reparent RTC clock from > > > > > external crystal oscillator, to internal RC oscillator, if external > > > > > oscillator fails. This is enabled by default. Disable it during > > > > > probe. > > > > > > > > > > Signed-off-by: Ondrej Jirman <megous@megous.com> > > > > > Reviewed-by: Chen-Yu Tsai <wens@csie.org> > > > > > --- > > > > > > > > > > drivers/rtc/rtc-sun6i.c | 40 > > > > > ++++++++++++++++++++++++++++++++++++++-- > > > > > 1 file changed, 38 insertions(+), 2 deletions(-) > > > > > > > > > > diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c > > > > > index d50ee023b559..b0c3752bed3f 100644 > > > > > --- a/drivers/rtc/rtc-sun6i.c > > > > > +++ b/drivers/rtc/rtc-sun6i.c > > > > > @@ -32,9 +32,11 @@ > > > > > > > > > > /* Control register */ > > > > > #define SUN6I_LOSC_CTRL 0x0000 > > > > > #define SUN6I_LOSC_CTRL_KEY (0x16aa << 16) > > > > > > > > > > +#define SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS BIT(15) > > > > > > > > User manual says that above field is bit 14. > > > > > > See the previous discussion, this is from BSP. > > > > I have two versions of BSP (don't ask me which) which have this set as bit > > 14 and changing this to 14 actually solves all my problems with LOSC (no > > more issues with setting RTC and HDMI-CEC works now - it uses LOSC as > > parent) on Tanix TX6 box. > > Interesting. Is LOSC fed externally generated clock, or is it setup as a > crystal oscillator on your board? I really don't know, but here is DT: http://ix.io/1ThI > > Anyway, see here: > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.h?h=h6-4.9-bsp#n649 > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n652 Interesting, 4.9 BSP has additional bit definition, which is not documented in manual and 3.10 BSP to which I refer. I was referring to 3.10 BSP, which uses only bit 14. I thought that you named it differently. > > It would be nice to know what's really happening. > > My output is: > > [ 0.832252] sun6i-rtc 7000000.rtc: registered as rtc0 > [ 0.832257] sun6i-rtc 7000000.rtc: RTC enabled > [ 1.728968] sun6i-rtc 7000000.rtc: setting system clock to > 1970-01-01T00:00:07 UTC (7) With change, I get same output. > > I think, you may have just enabled the auto switch feature, and running the > clock from low precision RC oscillator with your patch. True, now I think there is no external crystal, but I'm still not sure how to confirm that. > > The real issue probably is that the mainline driver is missing this: > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n650 > Not sure what you mean by that. ext vs. int source selection? Best regards, Jernej > regards, > o. > > > Best regards, > > Jernej > > > > > regards, > > > > > > o. > > > > > > > Best regards, > > > > Jernej > > > > > > > > > #define SUN6I_LOSC_CTRL_ALM_DHMS_ACC BIT(9) > > > > > #define SUN6I_LOSC_CTRL_RTC_HMS_ACC BIT(8) > > > > > #define SUN6I_LOSC_CTRL_RTC_YMD_ACC BIT(7) > > > > > > > > > > +#define SUN6I_LOSC_CTRL_EXT_LOSC_EN BIT(4) > > > > > > > > > > #define SUN6I_LOSC_CTRL_EXT_OSC BIT(0) > > > > > #define SUN6I_LOSC_CTRL_ACC_MASK GENMASK(9, 7) > > > > > > > > > > @@ -128,6 +130,8 @@ struct sun6i_rtc_clk_data { > > > > > > > > > > unsigned int has_prescaler : 1; > > > > > unsigned int has_out_clk : 1; > > > > > unsigned int export_iosc : 1; > > > > > > > > > > + unsigned int has_losc_en : 1; > > > > > + unsigned int has_auto_swt : 1; > > > > > > > > > > }; > > > > > > > > > > struct sun6i_rtc_dev { > > > > > > > > > > @@ -190,6 +194,10 @@ static int sun6i_rtc_osc_set_parent(struct > > > > > clk_hw > > > > > *hw, > > > > > u8 index) val &= ~SUN6I_LOSC_CTRL_EXT_OSC; > > > > > > > > > > val |= SUN6I_LOSC_CTRL_KEY; > > > > > val |= index ? SUN6I_LOSC_CTRL_EXT_OSC : 0; > > > > > > > > > > + if (rtc->data->has_losc_en) { > > > > > + val &= ~SUN6I_LOSC_CTRL_EXT_LOSC_EN; > > > > > + val |= index ? SUN6I_LOSC_CTRL_EXT_LOSC_EN : 0; > > > > > + } > > > > > > > > > > writel(val, rtc->base + SUN6I_LOSC_CTRL); > > > > > spin_unlock_irqrestore(&rtc->lock, flags); > > > > > > > > > > @@ -215,6 +223,7 @@ static void __init sun6i_rtc_clk_init(struct > > > > > device_node *node, const char *iosc_name = "rtc-int-osc"; > > > > > > > > > > const char *clkout_name = "osc32k-out"; > > > > > const char *parents[2]; > > > > > > > > > > + u32 reg; > > > > > > > > > > rtc = kzalloc(sizeof(*rtc), GFP_KERNEL); > > > > > if (!rtc) > > > > > > > > > > @@ -235,9 +244,18 @@ static void __init sun6i_rtc_clk_init(struct > > > > > device_node *node, goto err; > > > > > > > > > > } > > > > > > > > > > + reg = SUN6I_LOSC_CTRL_KEY; > > > > > + if (rtc->data->has_auto_swt) { > > > > > + /* Bypass auto-switch to int osc, on ext losc failure > > > > */ > > > > > > > + reg |= SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS; > > > > > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > > > > + } > > > > > + > > > > > > > > > > /* Switch to the external, more precise, oscillator */ > > > > > > > > > > - writel(SUN6I_LOSC_CTRL_KEY | SUN6I_LOSC_CTRL_EXT_OSC, > > > > > - rtc->base + SUN6I_LOSC_CTRL); > > > > > + reg |= SUN6I_LOSC_CTRL_EXT_OSC; > > > > > + if (rtc->data->has_losc_en) > > > > > + reg |= SUN6I_LOSC_CTRL_EXT_LOSC_EN; > > > > > + writel(reg, rtc->base + SUN6I_LOSC_CTRL); > > > > > > > > > > /* Yes, I know, this is ugly. */ > > > > > sun6i_rtc = rtc; > > > > > > > > > > @@ -345,6 +363,23 @@ CLK_OF_DECLARE_DRIVER(sun8i_h3_rtc_clk, > > > > > "allwinner,sun8i-h3-rtc", CLK_OF_DECLARE_DRIVER(sun50i_h5_rtc_clk, > > > > > "allwinner,sun50i-h5-rtc", sun8i_h3_rtc_clk_init); > > > > > > > > > > +static const struct sun6i_rtc_clk_data sun50i_h6_rtc_data = { > > > > > + .rc_osc_rate = 16000000, > > > > > + .fixed_prescaler = 32, > > > > > + .has_prescaler = 1, > > > > > + .has_out_clk = 1, > > > > > + .export_iosc = 1, > > > > > + .has_losc_en = 1, > > > > > + .has_auto_swt = 1, > > > > > +}; > > > > > + > > > > > +static void __init sun50i_h6_rtc_clk_init(struct device_node *node) > > > > > +{ > > > > > + sun6i_rtc_clk_init(node, &sun50i_h6_rtc_data); > > > > > +} > > > > > +CLK_OF_DECLARE_DRIVER(sun50i_h6_rtc_clk, "allwinner,sun50i-h6-rtc", > > > > > + sun50i_h6_rtc_clk_init); > > > > > + > > > > > > > > > > static const struct sun6i_rtc_clk_data sun8i_v3_rtc_data = { > > > > > > > > > > .rc_osc_rate = 32000, > > > > > .has_out_clk = 1, > > > > > > > > > > @@ -675,6 +710,7 @@ static const struct of_device_id > > > > > sun6i_rtc_dt_ids[] > > > > > = { > > > > > > > > > > { .compatible = "allwinner,sun8i-r40-rtc" }, > > > > > { .compatible = "allwinner,sun8i-v3-rtc" }, > > > > > { .compatible = "allwinner,sun50i-h5-rtc" }, > > > > > > > > > > + { .compatible = "allwinner,sun50i-h6-rtc" }, > > > > > > > > > > { /* sentinel */ }, > > > > > > > > > > }; > > > > > MODULE_DEVICE_TABLE(of, sun6i_rtc_dt_ids); > > > > > > > > _______________________________________________ > > > > linux-arm-kernel mailing list > > > > linux-arm-kernel@lists.infradead.org > > > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel > > > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel@lists.infradead.org > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Sat, Aug 24, 2019 at 03:16:41PM +0200, Jernej Škrabec wrote: > Dne sobota, 24. avgust 2019 ob 15:05:44 CEST je Ondřej Jirman napisal(a): > > On Sat, Aug 24, 2019 at 02:51:54PM +0200, Jernej Škrabec wrote: > > > Dne sobota, 24. avgust 2019 ob 14:46:54 CEST je Ondřej Jirman napisal(a): > > > > Hi, > > > > > > > > On Sat, Aug 24, 2019 at 02:32:32PM +0200, Jernej Škrabec wrote: > > > > > Hi! > > > > > > > > > > Dne torek, 20. avgust 2019 ob 17:19:33 CEST je megous@megous.com > > > > > > napisal(a): > > > > > > From: Ondrej Jirman <megous@megous.com> > > > > > > > > > > > > RTC on H6 is mostly the same as on H5 and H3. It has slight > > > > > > differences > > > > > > mostly in features that are not yet supported by this driver. > > > > > > > > > > > > Some differences are already stated in the comments in existing > > > > > > code. > > > > > > One other difference is that H6 has extra bit in LOSC_CTRL_REG, > > > > > > called > > > > > > EXT_LOSC_EN to enable/disable external low speed crystal oscillator. > > > > > > > > > > > > It also has bit EXT_LOSC_STA in LOSC_AUTO_SWT_STA_REG, to check > > > > > > whether > > > > > > external low speed oscillator is working correctly. > > > > > > > > > > > > This patch adds support for enabling LOSC when necessary: > > > > > > > > > > > > - during reparenting > > > > > > - when probing the clock > > > > > > > > > > > > H6 also has capacbility to automatically reparent RTC clock from > > > > > > external crystal oscillator, to internal RC oscillator, if external > > > > > > oscillator fails. This is enabled by default. Disable it during > > > > > > probe. > > > > > > > > > > > > Signed-off-by: Ondrej Jirman <megous@megous.com> > > > > > > Reviewed-by: Chen-Yu Tsai <wens@csie.org> > > > > > > --- > > > > > > > > > > > > drivers/rtc/rtc-sun6i.c | 40 > > > > > > ++++++++++++++++++++++++++++++++++++++-- > > > > > > 1 file changed, 38 insertions(+), 2 deletions(-) > > > > > > > > > > > > diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c > > > > > > index d50ee023b559..b0c3752bed3f 100644 > > > > > > --- a/drivers/rtc/rtc-sun6i.c > > > > > > +++ b/drivers/rtc/rtc-sun6i.c > > > > > > @@ -32,9 +32,11 @@ > > > > > > > > > > > > /* Control register */ > > > > > > #define SUN6I_LOSC_CTRL 0x0000 > > > > > > #define SUN6I_LOSC_CTRL_KEY (0x16aa > << 16) > > > > > > > > > > > > +#define SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS BIT(15) > > > > > > > > > > User manual says that above field is bit 14. > > > > > > > > See the previous discussion, this is from BSP. > > > > > > I have two versions of BSP (don't ask me which) which have this set as bit > > > 14 and changing this to 14 actually solves all my problems with LOSC (no > > > more issues with setting RTC and HDMI-CEC works now - it uses LOSC as > > > parent) on Tanix TX6 box. > > > > Interesting. Is LOSC fed externally generated clock, or is it setup as a > > crystal oscillator on your board? > > I really don't know, but here is DT: http://ix.io/1ThI > > > > > Anyway, see here: > > > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.h?h=h6-4.9-bsp#n649 > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n652 > > Interesting, 4.9 BSP has additional bit definition, which is not documented in > manual and 3.10 BSP to which I refer. > > I was referring to 3.10 BSP, which uses only bit 14. I thought that you named > it differently. > > > > > It would be nice to know what's really happening. > > > > My output is: > > > > [ 0.832252] sun6i-rtc 7000000.rtc: registered as rtc0 > > [ 0.832257] sun6i-rtc 7000000.rtc: RTC enabled > > [ 1.728968] sun6i-rtc 7000000.rtc: setting system clock to > > 1970-01-01T00:00:07 UTC (7) > > With change, I get same output. > > > > > I think, you may have just enabled the auto switch feature, and running the > > clock from low precision RC oscillator with your patch. > > True, now I think there is no external crystal, but I'm still not sure how to > confirm that. Visually? That would explain why it doesn't work for you. The mainline RTC driver disables auto-switch feature, and if your board doesn't have a crystal for LOSC, RTC will not generate a clock for the RTC. H6's dtsi describes by default a situatiuon with external 32k crystal oscillator. See ext_osc32k node. That's incorrect for your board if it doesn't have the crystal. You need to fix this in the DTS for your board instead of patching the driver. The driver has parent clock selection logic in case the LOSC crystal is not used. Your patch enables automatic detection of LOSC failure and RTC changes clock to LOSC automatically, despite what's described in the DTS. That may fix the issue, but is not the correct solution. Registers on my board look like this (external 32k osc is used) for reference: LOSC_CTRL_REG[7000000]: 8011 KEY_FIELD ??? (0) LOSC_AUTO_SWT_BYPASS EN (1) LOSC_AUTO_SWT_EN DIS (0) EXT_LOSC_EN EN (1) EXT_LOSC_GSM LOW (0) BATTERY_DIR DISCHARGE (0) LOSC_SRC_SEL EXT32k (1) LOSC_AUTO_SWT_STA_REG[7000004]: 1 EXT_LOSC_STA OK (0) LOSC_AUTO_SWT_PEND NOEFF (0) LOSC_SRC_SEL_STA EXT32K (1) regards, o. > > > > The real issue probably is that the mainline driver is missing this: > > > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n650 > > > > Not sure what you mean by that. ext vs. int source selection? > Best regards, > Jernej > > > regards, > > o.
Dne sobota, 24. avgust 2019 ob 15:30:57 CEST je Ondřej Jirman napisal(a): > On Sat, Aug 24, 2019 at 03:16:41PM +0200, Jernej Škrabec wrote: > > Dne sobota, 24. avgust 2019 ob 15:05:44 CEST je Ondřej Jirman napisal(a): > > > On Sat, Aug 24, 2019 at 02:51:54PM +0200, Jernej Škrabec wrote: > > > > Dne sobota, 24. avgust 2019 ob 14:46:54 CEST je Ondřej Jirman napisal(a): > > > > > Hi, > > > > > > > > > > On Sat, Aug 24, 2019 at 02:32:32PM +0200, Jernej Škrabec wrote: > > > > > > Hi! > > > > > > > > > > > > Dne torek, 20. avgust 2019 ob 17:19:33 CEST je megous@megous.com > > > > > > > > napisal(a): > > > > > > > From: Ondrej Jirman <megous@megous.com> > > > > > > > > > > > > > > RTC on H6 is mostly the same as on H5 and H3. It has slight > > > > > > > differences > > > > > > > mostly in features that are not yet supported by this driver. > > > > > > > > > > > > > > Some differences are already stated in the comments in existing > > > > > > > code. > > > > > > > One other difference is that H6 has extra bit in LOSC_CTRL_REG, > > > > > > > called > > > > > > > EXT_LOSC_EN to enable/disable external low speed crystal > > > > > > > oscillator. > > > > > > > > > > > > > > It also has bit EXT_LOSC_STA in LOSC_AUTO_SWT_STA_REG, to check > > > > > > > whether > > > > > > > external low speed oscillator is working correctly. > > > > > > > > > > > > > > This patch adds support for enabling LOSC when necessary: > > > > > > > > > > > > > > - during reparenting > > > > > > > - when probing the clock > > > > > > > > > > > > > > H6 also has capacbility to automatically reparent RTC clock from > > > > > > > external crystal oscillator, to internal RC oscillator, if > > > > > > > external > > > > > > > oscillator fails. This is enabled by default. Disable it during > > > > > > > probe. > > > > > > > > > > > > > > Signed-off-by: Ondrej Jirman <megous@megous.com> > > > > > > > Reviewed-by: Chen-Yu Tsai <wens@csie.org> > > > > > > > --- > > > > > > > > > > > > > > drivers/rtc/rtc-sun6i.c | 40 > > > > > > > ++++++++++++++++++++++++++++++++++++++-- > > > > > > > 1 file changed, 38 insertions(+), 2 deletions(-) > > > > > > > > > > > > > > diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c > > > > > > > index d50ee023b559..b0c3752bed3f 100644 > > > > > > > --- a/drivers/rtc/rtc-sun6i.c > > > > > > > +++ b/drivers/rtc/rtc-sun6i.c > > > > > > > @@ -32,9 +32,11 @@ > > > > > > > > > > > > > > /* Control register */ > > > > > > > #define SUN6I_LOSC_CTRL 0x0000 > > > > > > > #define SUN6I_LOSC_CTRL_KEY (0x16aa > > > > << 16) > > > > > > > > > +#define SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS BIT(15) > > > > > > > > > > > > User manual says that above field is bit 14. > > > > > > > > > > See the previous discussion, this is from BSP. > > > > > > > > I have two versions of BSP (don't ask me which) which have this set as > > > > bit > > > > 14 and changing this to 14 actually solves all my problems with LOSC > > > > (no > > > > more issues with setting RTC and HDMI-CEC works now - it uses LOSC as > > > > parent) on Tanix TX6 box. > > > > > > Interesting. Is LOSC fed externally generated clock, or is it setup as a > > > crystal oscillator on your board? > > > > I really don't know, but here is DT: http://ix.io/1ThI > > > > > Anyway, see here: > > > > > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.h?h=h6-4.9-bsp#n > > > 649 > > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n > > > 652 > > > > Interesting, 4.9 BSP has additional bit definition, which is not > > documented in manual and 3.10 BSP to which I refer. > > > > I was referring to 3.10 BSP, which uses only bit 14. I thought that you > > named it differently. > > > > > It would be nice to know what's really happening. > > > > > > My output is: > > > > > > [ 0.832252] sun6i-rtc 7000000.rtc: registered as rtc0 > > > [ 0.832257] sun6i-rtc 7000000.rtc: RTC enabled > > > [ 1.728968] sun6i-rtc 7000000.rtc: setting system clock to > > > 1970-01-01T00:00:07 UTC (7) > > > > With change, I get same output. > > > > > I think, you may have just enabled the auto switch feature, and running > > > the > > > clock from low precision RC oscillator with your patch. > > > > True, now I think there is no external crystal, but I'm still not sure how > > to confirm that. > > Visually? > > That would explain why it doesn't work for you. The mainline RTC driver > disables auto-switch feature, and if your board doesn't have a crystal for > LOSC, RTC will not generate a clock for the RTC. > > H6's dtsi describes by default a situatiuon with external 32k crystal > oscillator. See ext_osc32k node. That's incorrect for your board if it > doesn't have the crystal. You need to fix this in the DTS for your board > instead of patching the driver. I see that reparenting is supported, but I'm not sure how to fix that in DT. Any suggestion? > > The driver has parent clock selection logic in case the LOSC crystal is not > used. > > Your patch enables automatic detection of LOSC failure and RTC changes clock > to LOSC automatically, despite what's described in the DTS. That may fix > the issue, but is not the correct solution. > > Registers on my board look like this (external 32k osc is used) for > reference: > > LOSC_CTRL_REG[7000000]: 8011 > KEY_FIELD ??? (0) > LOSC_AUTO_SWT_BYPASS EN (1) > LOSC_AUTO_SWT_EN DIS (0) > EXT_LOSC_EN EN (1) > EXT_LOSC_GSM LOW (0) > BATTERY_DIR DISCHARGE (0) > LOSC_SRC_SEL EXT32k (1) > > LOSC_AUTO_SWT_STA_REG[7000004]: 1 > EXT_LOSC_STA OK (0) > LOSC_AUTO_SWT_PEND NOEFF (0) > LOSC_SRC_SEL_STA EXT32K (1) > In my case LOSC_CTRL_REG has value 0x4010 and LOSC_AUTO_SWT_STA_REG has value 0x4, so there is issue with external crystal (it's missing) and RTC switched to internal one. BTW, what's wrong with automatic switching? Why is it disabled? Best regards, Jernej > regards, > o. > > > > The real issue probably is that the mainline driver is missing this: > > > > > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n > > > 650 > > > > Not sure what you mean by that. ext vs. int source selection? > > > > > > > > Best regards, > > Jernej > > > > > regards, > > > > > > o.
Hello Jernej, On Sat, Aug 24, 2019 at 11:09:49PM +0200, Jernej Škrabec wrote: > > Visually? > > > > That would explain why it doesn't work for you. The mainline RTC driver > > disables auto-switch feature, and if your board doesn't have a crystal for > > LOSC, RTC will not generate a clock for the RTC. > > > > H6's dtsi describes by default a situatiuon with external 32k crystal > > oscillator. See ext_osc32k node. That's incorrect for your board if it > > doesn't have the crystal. You need to fix this in the DTS for your board > > instead of patching the driver. > > I see that reparenting is supported, but I'm not sure how to fix that in DT. > Any suggestion? You may try removing the clocks property from rtc node. > > > > The driver has parent clock selection logic in case the LOSC crystal is not > > used. > > > > Your patch enables automatic detection of LOSC failure and RTC changes clock > > to LOSC automatically, despite what's described in the DTS. That may fix > > the issue, but is not the correct solution. > > > > Registers on my board look like this (external 32k osc is used) for > > reference: > > > > LOSC_CTRL_REG[7000000]: 8011 > > KEY_FIELD ??? (0) > > LOSC_AUTO_SWT_BYPASS EN (1) > > LOSC_AUTO_SWT_EN DIS (0) > > EXT_LOSC_EN EN (1) > > EXT_LOSC_GSM LOW (0) > > BATTERY_DIR DISCHARGE (0) > > LOSC_SRC_SEL EXT32k (1) > > > > LOSC_AUTO_SWT_STA_REG[7000004]: 1 > > EXT_LOSC_STA OK (0) > > LOSC_AUTO_SWT_PEND NOEFF (0) > > LOSC_SRC_SEL_STA EXT32K (1) > > > > In my case LOSC_CTRL_REG has value 0x4010 and LOSC_AUTO_SWT_STA_REG > has value 0x4, so there is issue with external crystal (it's missing) and RTC > switched to internal one. > > BTW, what's wrong with automatic switching? Why is it disabled? It always was disabled on mainline (bit 14 was set to 0 even before my patch). H6 just probably has another extra undocummented bit, that's needed to disables it properly. You probably don't want a glitch to switch your RTC from high-precision clock to a low precision one possibly without any indication in the userspace or a kernel log. Regardless of all this, DTS needs to have a correct description of the HW, which means if RTC module is not connected to the 32.757kHz crystal/clock, clocks property should be empty. regards, o. > Best regards, > Jernej > > > regards, > > o. > > > > > > The real issue probably is that the mainline driver is missing this: > > > > > > > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-bsp#n > > > > 650 > > > > > > Not sure what you mean by that. ext vs. int source selection? > > > > > > > > > > > > Best regards, > > > Jernej > > > > > > > regards, > > > > > > > > o. > > > >
Dne sobota, 24. avgust 2019 ob 23:27:46 CEST je Ondřej Jirman napisal(a): > Hello Jernej, > > On Sat, Aug 24, 2019 at 11:09:49PM +0200, Jernej Škrabec wrote: > > > Visually? > > > > > > That would explain why it doesn't work for you. The mainline RTC driver > > > disables auto-switch feature, and if your board doesn't have a crystal > > > for > > > LOSC, RTC will not generate a clock for the RTC. > > > > > > H6's dtsi describes by default a situatiuon with external 32k crystal > > > oscillator. See ext_osc32k node. That's incorrect for your board if it > > > doesn't have the crystal. You need to fix this in the DTS for your board > > > instead of patching the driver. > > > > I see that reparenting is supported, but I'm not sure how to fix that in > > DT. Any suggestion? > > You may try removing the clocks property from rtc node. I don't think this would work: https://elixir.bootlin.com/linux/latest/source/drivers/rtc/rtc-sun6i.c#L246 > > > > The driver has parent clock selection logic in case the LOSC crystal is > > > not > > > used. > > > > > > Your patch enables automatic detection of LOSC failure and RTC changes > > > clock to LOSC automatically, despite what's described in the DTS. That > > > may fix the issue, but is not the correct solution. > > > > > > Registers on my board look like this (external 32k osc is used) for > > > reference: > > > > > > LOSC_CTRL_REG[7000000]: 8011 > > > > > > KEY_FIELD ??? (0) > > > LOSC_AUTO_SWT_BYPASS EN (1) > > > LOSC_AUTO_SWT_EN DIS (0) > > > EXT_LOSC_EN EN (1) > > > EXT_LOSC_GSM LOW (0) > > > BATTERY_DIR DISCHARGE (0) > > > LOSC_SRC_SEL EXT32k (1) > > > > > > LOSC_AUTO_SWT_STA_REG[7000004]: 1 > > > > > > EXT_LOSC_STA OK (0) > > > LOSC_AUTO_SWT_PEND NOEFF (0) > > > LOSC_SRC_SEL_STA EXT32K (1) > > > > In my case LOSC_CTRL_REG has value 0x4010 and LOSC_AUTO_SWT_STA_REG > > has value 0x4, so there is issue with external crystal (it's missing) and > > RTC switched to internal one. > > > > BTW, what's wrong with automatic switching? Why is it disabled? > > It always was disabled on mainline (bit 14 was set to 0 even before my > patch). H6 just probably has another extra undocummented bit, that's needed > to disables it properly. > > You probably don't want a glitch to switch your RTC from high-precision > clock to a low precision one possibly without any indication in the > userspace or a kernel log. > > Regardless of all this, DTS needs to have a correct description of the HW, > which means if RTC module is not connected to the 32.757kHz crystal/clock, > clocks property should be empty. If we are talking about correct HW description, then clock property should actually have possibility that two clocks are defined - one for internal RC (always present) and one external crystal (optional). In such case I could really just omit external clock and be done with it. But I'm not sure if such solution is acceptable at this point. Best regards, Jernej > > regards, > o. > > > Best regards, > > Jernej > > > > > regards, > > > > > > o. > > > > > > > > The real issue probably is that the mainline driver is missing this: > > > > > > > > > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-b > > > > > sp#n > > > > > 650 > > > > > > > > Not sure what you mean by that. ext vs. int source selection? > > > > > > > > > > > > > > > > Best regards, > > > > Jernej > > > > > > > > > regards, > > > > > > > > > > o.
On Sat, Aug 24, 2019 at 11:36:26PM +0200, Jernej Škrabec wrote: > Dne sobota, 24. avgust 2019 ob 23:27:46 CEST je Ondřej Jirman napisal(a): > > Hello Jernej, > > > > On Sat, Aug 24, 2019 at 11:09:49PM +0200, Jernej Škrabec wrote: > > > > Visually? > > > > > > > > That would explain why it doesn't work for you. The mainline RTC driver > > > > disables auto-switch feature, and if your board doesn't have a crystal > > > > for > > > > LOSC, RTC will not generate a clock for the RTC. > > > > > > > > H6's dtsi describes by default a situatiuon with external 32k crystal > > > > oscillator. See ext_osc32k node. That's incorrect for your board if it > > > > doesn't have the crystal. You need to fix this in the DTS for your board > > > > instead of patching the driver. > > > > > > I see that reparenting is supported, but I'm not sure how to fix that in > > > DT. Any suggestion? > > > > You may try removing the clocks property from rtc node. > > I don't think this would work: > https://elixir.bootlin.com/linux/latest/source/drivers/rtc/rtc-sun6i.c#L246 Well, I don't know. There has to be some way to make it work, since the code deals with it here: https://elixir.bootlin.com/linux/latest/source/drivers/rtc/rtc-sun6i.c#L270 Number of parents for LOSC is calculated from the DT somehow. Maybne something to do with the #clock-cells property? Sorry I can't be of more help here. > > > > > > The driver has parent clock selection logic in case the LOSC crystal is > > > > not > > > > used. > > > > > > > > Your patch enables automatic detection of LOSC failure and RTC changes > > > > clock to LOSC automatically, despite what's described in the DTS. That > > > > may fix the issue, but is not the correct solution. > > > > > > > > Registers on my board look like this (external 32k osc is used) for > > > > reference: > > > > > > > > LOSC_CTRL_REG[7000000]: 8011 > > > > > > > > KEY_FIELD ??? (0) > > > > LOSC_AUTO_SWT_BYPASS EN (1) > > > > LOSC_AUTO_SWT_EN DIS (0) > > > > EXT_LOSC_EN EN (1) > > > > EXT_LOSC_GSM LOW (0) > > > > BATTERY_DIR DISCHARGE (0) > > > > LOSC_SRC_SEL EXT32k (1) > > > > > > > > LOSC_AUTO_SWT_STA_REG[7000004]: 1 > > > > > > > > EXT_LOSC_STA OK (0) > > > > LOSC_AUTO_SWT_PEND NOEFF (0) > > > > LOSC_SRC_SEL_STA EXT32K (1) > > > > > > In my case LOSC_CTRL_REG has value 0x4010 and LOSC_AUTO_SWT_STA_REG > > > has value 0x4, so there is issue with external crystal (it's missing) and > > > RTC switched to internal one. > > > > > > BTW, what's wrong with automatic switching? Why is it disabled? > > > > It always was disabled on mainline (bit 14 was set to 0 even before my > > patch). H6 just probably has another extra undocummented bit, that's needed > > to disables it properly. > > > > You probably don't want a glitch to switch your RTC from high-precision > > clock to a low precision one possibly without any indication in the > > userspace or a kernel log. > > > > Regardless of all this, DTS needs to have a correct description of the HW, > > which means if RTC module is not connected to the 32.757kHz crystal/clock, > > clocks property should be empty. > > If we are talking about correct HW description, then clock property should > actually have possibility that two clocks are defined - one for internal RC > (always present) and one external crystal (optional). In such case I could > really just omit external clock and be done with it. But I'm not sure if such Internal RC is thought to be part of the RTC module, so it's not defined as an input clock to the RTC module. regards, Ondrej > > Best regards, > Jernej > > > > > regards, > > o. > > > > > Best regards, > > > Jernej > > > > > > > regards, > > > > > > > > o. > > > > > > > > > > The real issue probably is that the mainline driver is missing this: > > > > > > > > > > > > https://megous.com/git/linux/tree/drivers/rtc/rtc-sunxi.c?h=h6-4.9-b > > > > > > sp#n > > > > > > 650 > > > > > > > > > > Not sure what you mean by that. ext vs. int source selection? > > > > > > > > > > > > > > > > > > > > Best regards, > > > > > Jernej > > > > > > > > > > > regards, > > > > > > > > > > > > o. > > > >
diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c index d50ee023b559..b0c3752bed3f 100644 --- a/drivers/rtc/rtc-sun6i.c +++ b/drivers/rtc/rtc-sun6i.c @@ -32,9 +32,11 @@ /* Control register */ #define SUN6I_LOSC_CTRL 0x0000 #define SUN6I_LOSC_CTRL_KEY (0x16aa << 16) +#define SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS BIT(15) #define SUN6I_LOSC_CTRL_ALM_DHMS_ACC BIT(9) #define SUN6I_LOSC_CTRL_RTC_HMS_ACC BIT(8) #define SUN6I_LOSC_CTRL_RTC_YMD_ACC BIT(7) +#define SUN6I_LOSC_CTRL_EXT_LOSC_EN BIT(4) #define SUN6I_LOSC_CTRL_EXT_OSC BIT(0) #define SUN6I_LOSC_CTRL_ACC_MASK GENMASK(9, 7) @@ -128,6 +130,8 @@ struct sun6i_rtc_clk_data { unsigned int has_prescaler : 1; unsigned int has_out_clk : 1; unsigned int export_iosc : 1; + unsigned int has_losc_en : 1; + unsigned int has_auto_swt : 1; }; struct sun6i_rtc_dev { @@ -190,6 +194,10 @@ static int sun6i_rtc_osc_set_parent(struct clk_hw *hw, u8 index) val &= ~SUN6I_LOSC_CTRL_EXT_OSC; val |= SUN6I_LOSC_CTRL_KEY; val |= index ? SUN6I_LOSC_CTRL_EXT_OSC : 0; + if (rtc->data->has_losc_en) { + val &= ~SUN6I_LOSC_CTRL_EXT_LOSC_EN; + val |= index ? SUN6I_LOSC_CTRL_EXT_LOSC_EN : 0; + } writel(val, rtc->base + SUN6I_LOSC_CTRL); spin_unlock_irqrestore(&rtc->lock, flags); @@ -215,6 +223,7 @@ static void __init sun6i_rtc_clk_init(struct device_node *node, const char *iosc_name = "rtc-int-osc"; const char *clkout_name = "osc32k-out"; const char *parents[2]; + u32 reg; rtc = kzalloc(sizeof(*rtc), GFP_KERNEL); if (!rtc) @@ -235,9 +244,18 @@ static void __init sun6i_rtc_clk_init(struct device_node *node, goto err; } + reg = SUN6I_LOSC_CTRL_KEY; + if (rtc->data->has_auto_swt) { + /* Bypass auto-switch to int osc, on ext losc failure */ + reg |= SUN6I_LOSC_CTRL_AUTO_SWT_BYPASS; + writel(reg, rtc->base + SUN6I_LOSC_CTRL); + } + /* Switch to the external, more precise, oscillator */ - writel(SUN6I_LOSC_CTRL_KEY | SUN6I_LOSC_CTRL_EXT_OSC, - rtc->base + SUN6I_LOSC_CTRL); + reg |= SUN6I_LOSC_CTRL_EXT_OSC; + if (rtc->data->has_losc_en) + reg |= SUN6I_LOSC_CTRL_EXT_LOSC_EN; + writel(reg, rtc->base + SUN6I_LOSC_CTRL); /* Yes, I know, this is ugly. */ sun6i_rtc = rtc; @@ -345,6 +363,23 @@ CLK_OF_DECLARE_DRIVER(sun8i_h3_rtc_clk, "allwinner,sun8i-h3-rtc", CLK_OF_DECLARE_DRIVER(sun50i_h5_rtc_clk, "allwinner,sun50i-h5-rtc", sun8i_h3_rtc_clk_init); +static const struct sun6i_rtc_clk_data sun50i_h6_rtc_data = { + .rc_osc_rate = 16000000, + .fixed_prescaler = 32, + .has_prescaler = 1, + .has_out_clk = 1, + .export_iosc = 1, + .has_losc_en = 1, + .has_auto_swt = 1, +}; + +static void __init sun50i_h6_rtc_clk_init(struct device_node *node) +{ + sun6i_rtc_clk_init(node, &sun50i_h6_rtc_data); +} +CLK_OF_DECLARE_DRIVER(sun50i_h6_rtc_clk, "allwinner,sun50i-h6-rtc", + sun50i_h6_rtc_clk_init); + static const struct sun6i_rtc_clk_data sun8i_v3_rtc_data = { .rc_osc_rate = 32000, .has_out_clk = 1, @@ -675,6 +710,7 @@ static const struct of_device_id sun6i_rtc_dt_ids[] = { { .compatible = "allwinner,sun8i-r40-rtc" }, { .compatible = "allwinner,sun8i-v3-rtc" }, { .compatible = "allwinner,sun50i-h5-rtc" }, + { .compatible = "allwinner,sun50i-h6-rtc" }, { /* sentinel */ }, }; MODULE_DEVICE_TABLE(of, sun6i_rtc_dt_ids);