diff mbox series

[5/6] arm64: dts: meson-g12a: Add PCIe node

Message ID 1567950178-4466-6-git-send-email-narmstrong@baylibre.com (mailing list archive)
State Superseded, archived
Headers show
Series arm64: dts: meson-g12: add support for PCIe | expand

Commit Message

Neil Armstrong Sept. 8, 2019, 1:42 p.m. UTC
This adds the Amlogic G12A PCI Express controller node, also
using the USB3+PCIe Combo PHY.

The PHY mode selection is static, thus the USB3+PCIe Combo PHY
phandle would need to be removed from the USB control node if the
shared differentil lines are used for PCIe instead of USB3.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 .../boot/dts/amlogic/meson-g12-common.dtsi    | 33 +++++++++++++++++++
 1 file changed, 33 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
index 852cf9cf121b..7330dc37b7a6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
@@ -95,6 +95,39 @@ 
 		#size-cells = <2>;
 		ranges;
 
+		pcie: pcie@fc000000 {
+			compatible = "amlogic,g12a-pcie", "snps,dw-pcie";
+			reg = <0x0 0xfc000000 0x0 0x400000
+			       0x0 0xff648000 0x0 0x2000
+			       0x0 0xfc400000 0x0 0x200000>;
+			reg-names = "elbi", "cfg", "config";
+			interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x0 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0 0x0 0xfc600000 0 0x00100000
+				  0x82000000 0 0xfc700000 0x0 0xfc700000 0 0x1900000>;
+
+			clocks = <&clkc CLKID_PCIE_PHY
+				  &clkc CLKID_PCIE_COMB
+				  &clkc CLKID_PCIE_PLL>;
+			clock-names = "general",
+				      "pclk",
+				      "port";
+			resets = <&reset RESET_PCIE_CTRL_A>,
+				 <&reset RESET_PCIE_APB>;
+			reset-names = "port",
+				      "apb";
+			num-lanes = <1>;
+			phys = <&usb3_pcie_phy PHY_TYPE_PCIE>;
+			phy-names = "pcie";
+			status = "disabled";
+		};
+
 		ethmac: ethernet@ff3f0000 {
 			compatible = "amlogic,meson-axg-dwmac",
 				     "snps,dwmac-3.70a",