diff mbox series

[v2,1/6] dt-bindings: pci: amlogic,meson-pcie: Add G12A bindings

Message ID 20190916125022.10754-2-narmstrong@baylibre.com (mailing list archive)
State Mainlined, archived
Commit 0978e95253c64bda17e1c2da5c30744980ca73d3
Headers show
Series arm64: dts: meson-g12: add support for PCIe | expand

Commit Message

Neil Armstrong Sept. 16, 2019, 12:50 p.m. UTC
Add PCIE bindings for the Amlogic G12A SoC, the support is the same
but the PHY is shared with USB3 to control the differential lines.

Thus this adds a phy phandle to control the PHY, and only requires the
MIPI clock for the Amlogic AXG SoC Family.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/pci/amlogic,meson-pcie.txt   | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

Comments

Andrew Murray Sept. 16, 2019, 1:46 p.m. UTC | #1
On Mon, Sep 16, 2019 at 02:50:17PM +0200, Neil Armstrong wrote:
> Add PCIE bindings for the Amlogic G12A SoC, the support is the same
> but the PHY is shared with USB3 to control the differential lines.
> 
> Thus this adds a phy phandle to control the PHY, and only requires the
> MIPI clock for the Amlogic AXG SoC Family.
> 
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---

Reviewed-by: Andrew Murray <andrew.murray@arm.com>

>  .../devicetree/bindings/pci/amlogic,meson-pcie.txt   | 12 ++++++++----
>  1 file changed, 8 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
> index efa2c8b9b85a..84fdc422792e 100644
> --- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
> @@ -9,13 +9,16 @@ Additional properties are described here:
>  
>  Required properties:
>  - compatible:
> -	should contain "amlogic,axg-pcie" to identify the core.
> +	should contain :
> +	- "amlogic,axg-pcie" for AXG SoC Family
> +	- "amlogic,g12a-pcie" for G12A SoC Family
> +	to identify the core.
>  - reg:
>  	should contain the configuration address space.
>  - reg-names: Must be
>  	- "elbi"	External local bus interface registers
>  	- "cfg"		Meson specific registers
> -	- "phy"		Meson PCIE PHY registers
> +	- "phy"		Meson PCIE PHY registers for AXG SoC Family
>  	- "config"	PCIe configuration space
>  - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
>  - clocks: Must contain an entry for each entry in clock-names.
> @@ -23,12 +26,13 @@ Required properties:
>  	- "pclk"       PCIe GEN 100M PLL clock
>  	- "port"       PCIe_x(A or B) RC clock gate
>  	- "general"    PCIe Phy clock
> -	- "mipi"       PCIe_x(A or B) 100M ref clock gate
> +	- "mipi"       PCIe_x(A or B) 100M ref clock gate for AXG SoC Family
>  - resets: phandle to the reset lines.
>  - reset-names: must contain "phy" "port" and "apb"
> -       - "phy"         Share PHY reset
> +       - "phy"         Share PHY reset for AXG SoC Family
>         - "port"        Port A or B reset
>         - "apb"         Share APB reset
> +- phys: should contain a phandle to the shared phy for G12A SoC Family
>  - device_type:
>  	should be "pci". As specified in designware-pcie.txt
>  
> -- 
> 2.22.0
>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
index efa2c8b9b85a..84fdc422792e 100644
--- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
@@ -9,13 +9,16 @@  Additional properties are described here:
 
 Required properties:
 - compatible:
-	should contain "amlogic,axg-pcie" to identify the core.
+	should contain :
+	- "amlogic,axg-pcie" for AXG SoC Family
+	- "amlogic,g12a-pcie" for G12A SoC Family
+	to identify the core.
 - reg:
 	should contain the configuration address space.
 - reg-names: Must be
 	- "elbi"	External local bus interface registers
 	- "cfg"		Meson specific registers
-	- "phy"		Meson PCIE PHY registers
+	- "phy"		Meson PCIE PHY registers for AXG SoC Family
 	- "config"	PCIe configuration space
 - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
 - clocks: Must contain an entry for each entry in clock-names.
@@ -23,12 +26,13 @@  Required properties:
 	- "pclk"       PCIe GEN 100M PLL clock
 	- "port"       PCIe_x(A or B) RC clock gate
 	- "general"    PCIe Phy clock
-	- "mipi"       PCIe_x(A or B) 100M ref clock gate
+	- "mipi"       PCIe_x(A or B) 100M ref clock gate for AXG SoC Family
 - resets: phandle to the reset lines.
 - reset-names: must contain "phy" "port" and "apb"
-       - "phy"         Share PHY reset
+       - "phy"         Share PHY reset for AXG SoC Family
        - "port"        Port A or B reset
        - "apb"         Share APB reset
+- phys: should contain a phandle to the shared phy for G12A SoC Family
 - device_type:
 	should be "pci". As specified in designware-pcie.txt