@@ -523,12 +523,12 @@ static const char *fixup_tplg_name(struct snd_sof_dev *sdev,
static int hda_init_caps(struct snd_sof_dev *sdev)
{
struct hdac_bus *bus = sof_to_bus(sdev);
+ struct snd_soc_acpi_mach *mach;
+ struct snd_sof_pdata *pdata = sdev->pdata;
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
struct hdac_ext_link *hlink;
- struct snd_soc_acpi_mach_params *mach_params;
struct snd_soc_acpi_mach *hda_mach;
- struct snd_sof_pdata *pdata = sdev->pdata;
- struct snd_soc_acpi_mach *mach;
+ struct snd_soc_acpi_mach_params *mach_params;
const char *tplg_filename;
const char *idisp_str;
const char *dmic_str;
@@ -536,7 +536,7 @@ static int hda_init_caps(struct snd_sof_dev *sdev)
int codec_num = 0;
int i;
#endif
- struct sof_intel_hda_dev *hdev;
+ struct sof_intel_hda_dev *hdev = pdata->hw_pdata;
u32 link_mask;
int ret = 0;
@@ -574,19 +574,49 @@ static int hda_init_caps(struct snd_sof_dev *sdev)
}
link_mask = hdev->info.link_mask;
- if (!link_mask) {
- /*
- * probe/allocated SoundWire resources.
- * The hardware configuration takes place in hda_sdw_startup
- * after power rails are enabled.
- */
- ret = hda_sdw_probe(sdev);
- if (ret < 0) {
- dev_err(sdev->dev, "error: SoundWire probe error\n");
- return ret;
+ if (!link_mask)
+ goto skip_soundwire;
+
+ /*
+ * probe/allocate SoundWire resources.
+ * The hardware configuration takes place in hda_sdw_startup
+ * after power rails are enabled.
+ * It's entirely possible to have a mix of I2S/DMIC/SoundWire
+ * devices, so we allocate the resources in all cases.
+ */
+ ret = hda_sdw_probe(sdev);
+ if (ret < 0) {
+ dev_err(sdev->dev, "error: SoundWire probe error\n");
+ return ret;
+ }
+
+ /*
+ * Select SoundWire machine driver if needed using the
+ * alternate tables. This case deals with SoundWire-only
+ * machines, for mixed cases with I2C/I2S the detection relies
+ * on the HID list.
+ */
+ if (!pdata->machine) {
+ mach = pdata->desc->alt_machines;
+ while (mach && mach->link_mask && mach->link_mask != link_mask)
+ mach++;
+ if (mach && mach->link_mask) {
+ dev_dbg(bus->dev,
+ "SoundWire machine driver %s topology %s\n",
+ mach->drv_name,
+ mach->sof_tplg_filename);
+ pdata->machine = mach;
+ mach->mach_params.platform = dev_name(sdev->dev);
+ pdata->fw_filename = mach->sof_fw_filename;
+ pdata->tplg_filename = mach->sof_tplg_filename;
+ } else {
+ dev_info(sdev->dev,
+ "No SoundWire machine driver found\n");
}
}
+skip_soundwire:
+
#if IS_ENABLED(CONFIG_SND_SOC_SOF_HDA)
if (bus->mlcap)
snd_hdac_ext_bus_get_ml_capabilities(bus);
For now we have a limited number of machine driver configurations, and we can detect them based on the link configuration returned after checking hardware and firmware (BIOS) configurations. It's likely that in the future we will need to check for _ADR match as well, which can easily be done by extending the acpi_info structure. There is a chance that in extreme cases where the BIOS contains too much information we would need to detect which Slave devices actually report as 'attached'. This would be more accurate than static table-based solutions, but it also introduces timing dependencies since we don't know when those devices might become attached, so will only be only be looked at if we see limitations with static methods and the usual quirks based e.g. on DMI information. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> --- sound/soc/sof/intel/hda.c | 58 +++++++++++++++++++++++++++++---------- 1 file changed, 44 insertions(+), 14 deletions(-)