[RFT] ath10k: add QCA9377 sdio hw_param item
diff mbox series

Message ID 1569507867-19547-1-git-send-email-kvalo@codeaurora.org
State New
Headers show
Series
  • [RFT] ath10k: add QCA9377 sdio hw_param item
Related show

Commit Message

Kalle Valo Sept. 26, 2019, 2:24 p.m. UTC
From: Erik Stromdahl <erik.stromdahl@gmail.com>

Add hardware parameters for QCA9377 sdio devices, it's now properly supported.

Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
---

I don't have any working QCA9377 SDIO hardware so I would appreciate any
test reports. This should apply cleanly to ath.git master branch (at least to
tag ath-201909230832):

https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/log/?h=master

 drivers/net/wireless/ath/ath10k/core.c | 27 +++++++++++++++++++++++++++
 drivers/net/wireless/ath/ath10k/hw.h   |  3 +++
 2 files changed, 30 insertions(+)

Patch
diff mbox series

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 36c62d66c19e..e5572d4b6ae9 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -539,6 +539,33 @@  static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 		.tx_stats_over_pktlog = false,
 	},
 	{
+		.id = QCA9377_HW_1_1_DEV_VERSION,
+		.dev_id = QCA9377_1_0_DEVICE_ID,
+		.bus = ATH10K_BUS_SDIO,
+		.name = "qca9377 hw1.1 sdio",
+		.patch_load_addr = QCA9377_HW_1_0_PATCH_LOAD_ADDR,
+		.uart_pin = 19,
+		.otp_exe_param = 0,
+		.channel_counters_freq_hz = 88000,
+		.max_probe_resp_desc_thres = 0,
+		.cal_data_len = 8124,
+		.fw = {
+			.dir = QCA9377_HW_1_0_FW_DIR,
+			.board = QCA9377_HW_1_0_BOARD_DATA_FILE,
+			.board_size = QCA9377_BOARD_DATA_SZ,
+			.board_ext_size = QCA9377_BOARD_EXT_DATA_SZ,
+		},
+		.hw_ops = &qca6174_ops,
+		.hw_clk = qca6174_clk,
+		.target_cpu_freq = 176000000,
+		.decap_align_bytes = 4,
+		.n_cipher_suites = 8,
+		.num_peers = TARGET_QCA9377_HL_NUM_PEERS,
+		.ast_skid_limit = 0x10,
+		.num_wds_entries = 0x20,
+		.uart_pin_workaround = true,
+	},
+	{
 		.id = QCA4019_HW_1_0_DEV_VERSION,
 		.dev_id = 0,
 		.bus = ATH10K_BUS_AHB,
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 2ae57c1de7b5..ddb1d23ec6de 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -768,6 +768,9 @@  ath10k_is_rssi_enable(struct ath10k_hw_params *hw,
 #define TARGET_HL_TLV_AST_SKID_LIMIT		16
 #define TARGET_HL_TLV_NUM_WDS_ENTRIES		2
 
+/* Target specific defines for QCA9377 high latency firmware */
+#define TARGET_QCA9377_HL_NUM_PEERS		15
+
 /* Diagnostic Window */
 #define CE_DIAG_PIPE	7