[2/2] dt-bindings: pinctrl: Add MSM8976 driver bindings and documentation

Commit Message

AngeloGioacchino Del Regno Oct. 5, 2019, 10:59 a.m. UTC

From: AngeloGioacchino Del Regno <[e-mail]>

Add the documentation for this new driver for pin configuration
with the pinctrl framework on MSM8976/56 and its APQ variants.
---
 .../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 ++++++++++++++++++
 1 file changed, 183 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt

Comments

Bjorn Andersson Oct. 7, 2019, 5:56 a.m. UTC | #1

On Sat 05 Oct 03:59 PDT 2019, [e-mail] wrote:

> From: AngeloGioacchino Del Regno <[e-mail]>
> 
> Add the documentation for this new driver for pin configuration
> with the pinctrl framework on MSM8976/56 and its APQ variants.

You forgot your Signed-off-by on this patch.

Reviewed-by: Bjorn Andersson <[e-mail]>

Regards,
Bjorn

> ---
>  .../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 ++++++++++++++++++
>  1 file changed, 183 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> new file mode 100644
> index 000000000000..70d04d12f136
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> @@ -0,0 +1,183 @@
> +Qualcomm MSM8976 TLMM block
> +
> +This binding describes the Top Level Mode Multiplexer block found in the
> +MSM8956 and MSM8976 platforms.
> +
> +- compatible:
> +	Usage: required
> +	Value type: <string>
> +	Definition: must be "qcom,msm8976-pinctrl"
> +
> +- reg:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: the base address and size of the TLMM register space.
> +
> +- interrupts:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: should specify the TLMM summary IRQ.
> +
> +- interrupt-controller:
> +	Usage: required
> +	Value type: <none>
> +	Definition: identifies this node as an interrupt controller
> +
> +- #interrupt-cells:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: must be 2. Specifying the pin number and flags, as defined
> +		    in <dt-bindings/interrupt-controller/irq.h>
> +
> +- gpio-controller:
> +	Usage: required
> +	Value type: <none>
> +	Definition: identifies this node as a gpio controller
> +
> +- #gpio-cells:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: must be 2. Specifying the pin number and flags, as defined
> +		    in <dt-bindings/gpio/gpio.h>
> +
> +- gpio-ranges:
> +	Usage: required
> +	Definition:  see ../gpio/gpio.txt
> +
> +- gpio-reserved-ranges:
> +	Usage: optional
> +	Definition: see ../gpio/gpio.txt
> +
> +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
> +a general description of GPIO and interrupt bindings.
> +
> +Please refer to pinctrl-bindings.txt in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +The pin configuration nodes act as a container for an arbitrary number of
> +subnodes. Each of these subnodes represents some desired configuration for a
> +pin, a group, or a list of pins or groups. This configuration can include the
> +mux function to select on those pin(s)/group(s), and various pin configuration
> +parameters, such as pull-up, drive strength, etc.
> +
> +
> +PIN CONFIGURATION NODES:
> +
> +The name of each subnode is not important; all subnodes should be enumerated
> +and processed purely based on their content.
> +
> +Each subnode only affects those parameters that are explicitly listed. In
> +other words, a subnode that lists a mux function but no pin configuration
> +parameters implies no information about any pin configuration parameters.
> +Similarly, a pin subnode that describes a pullup parameter implies no
> +information about e.g. the mux function.
> +
> +
> +The following generic properties as defined in pinctrl-bindings.txt are valid
> +to specify in a pin configuration subnode:
> +
> +- pins:
> +	Usage: required
> +	Value type: <string-array>
> +	Definition: List of gpio pins affected by the properties specified in
> +		    this subnode.
> +
> +		    Valid pins are:
> +		      gpio0-gpio145
> +		        Supports mux, bias and drive-strength
> +
> +		      sdc1_clk, sdc1_cmd, sdc1_data,
> +		      sdc2_clk, sdc2_cmd, sdc2_data,
> +		      sdc3_clk, sdc3_cmd, sdc3_data
> +		        Supports bias and drive-strength
> +
> +- function:
> +	Usage: required
> +	Value type: <string>
> +	Definition: Specify the alternative function to be configured for the
> +		    specified pins. Functions are only valid for gpio pins.
> +		    Valid values are:
> +
> +		    gpio, blsp_uart1, blsp_spi1, smb_int, blsp_i2c1, blsp_spi2,
> +		    blsp_uart2, blsp_i2c2, gcc_gp1_clk_b, blsp_spi3,
> +		    qdss_tracedata_b, blsp_i2c3, gcc_gp2_clk_b, gcc_gp3_clk_b,
> +		    blsp_spi4, cap_int, blsp_i2c4, blsp_spi5, blsp_uart5,
> +		    qdss_traceclk_a, m_voc, blsp_i2c5, qdss_tracectl_a,
> +		    qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b,
> +		    blsp_i2c6, qdss_traceclk_b, mdp_vsync, pri_mi2s_mclk_a,
> +		    sec_mi2s_mclk_a, cam_mclk, cci0_i2c, cci1_i2c, blsp1_spi,
> +		    blsp3_spi, gcc_gp1_clk_a, gcc_gp2_clk_a, gcc_gp3_clk_a,
> +		    uim_batt, sd_write, uim1_data, uim1_clk, uim1_reset,
> +		    uim1_present, uim2_data, uim2_clk, uim2_reset,
> +		    uim2_present, ts_xvdd, mipi_dsi0, us_euro, ts_resout,
> +		    ts_sample, sec_mi2s_mclk_b, pri_mi2s, codec_reset,
> +		    cdc_pdm0, us_emitter, pri_mi2s_mclk_b, pri_mi2s_mclk_c,
> +		    lpass_slimbus, lpass_slimbus0, lpass_slimbus1, codec_int1,
> +		    codec_int2, wcss_bt, sdc3, wcss_wlan2, wcss_wlan1,
> +		    wcss_wlan0, wcss_wlan, wcss_fm, key_volp, key_snapshot,
> +		    key_focus, key_home, pwr_down, dmic0_clk, hdmi_int,
> +		    dmic0_data, wsa_vi, wsa_en, blsp_spi8, wsa_irq, blsp_i2c8,
> +		    pa_indicator, modem_tsync, ssbi_wtr1, gsm1_tx, gsm0_tx,
> +		    sdcard_det, sec_mi2s, ss_switch,
> +
> +- bias-disable:
> +	Usage: optional
> +	Value type: <none>
> +	Definition: The specified pins should be configured as no pull.
> +
> +- bias-pull-down:
> +	Usage: optional
> +	Value type: <none>
> +	Definition: The specified pins should be configured as pull down.
> +
> +- bias-pull-up:
> +	Usage: optional
> +	Value type: <none>
> +	Definition: The specified pins should be configured as pull up.
> +
> +- output-high:
> +	Usage: optional
> +	Value type: <none>
> +	Definition: The specified pins are configured in output mode, driven
> +		    high.
> +		    Not valid for sdc pins.
> +
> +- output-low:
> +	Usage: optional
> +	Value type: <none>
> +	Definition: The specified pins are configured in output mode, driven
> +		    low.
> +		    Not valid for sdc pins.
> +
> +- drive-strength:
> +	Usage: optional
> +	Value type: <u32>
> +	Definition: Selects the drive strength for the specified pins, in mA.
> +		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
> +
> +Example:
> +
> +	tlmm: pinctrl@1000000 {
> +		compatible = "qcom,msm8976-pinctrl";
> +		reg = <0x1000000 0x300000>;
> +		interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-ranges = <&tlmm 0 0 145>;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +
> +		blsp1_uart2_active: blsp1_uart2_active {
> +			mux {
> +				pins = "gpio4", "gpio5", "gpio6", "gpio7";
> +				function = "blsp_uart2";
> +			};
> +
> +			config {
> +				pins = "gpio4", "gpio5", "gpio6", "gpio7";
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +		};
> +	};
> -- 
> 2.21.0
>

AngeloGioacchino Del Regno Oct. 15, 2019, 10:39 a.m. UTC | #2

Il giorno lun 7 ott 2019 alle ore 07:56 Bjorn Andersson
<[e-mail]> ha scritto:
>
> On Sat 05 Oct 03:59 PDT 2019, [e-mail] wrote:
>
> > From: AngeloGioacchino Del Regno <[e-mail]>
> >
> > Add the documentation for this new driver for pin configuration
> > with the pinctrl framework on MSM8976/56 and its APQ variants.
>
> You forgot your Signed-off-by on this patch.
>
> Reviewed-by: Bjorn Andersson <[e-mail]>
>
> Regards,
> Bjorn
>

Oops! That was totally unintentional.
I don't know how should I proceed in these cases but seems overkill to resend
the entire thing just to add the tag. If I have to then I will,
otherwise, whoever
will apply this, please feel free to add my

Signed-off-by: AngeloGioacchino Del Regno <[e-mail]>

Thanks,
Angelo

> > ---
> >  .../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 ++++++++++++++++++
> >  1 file changed, 183 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> >
> > diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> > new file mode 100644
> > index 000000000000..70d04d12f136
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> > @@ -0,0 +1,183 @@
> > +Qualcomm MSM8976 TLMM block
> > +
> > +This binding describes the Top Level Mode Multiplexer block found in the
> > +MSM8956 and MSM8976 platforms.
> > +
> > +- compatible:
> > +     Usage: required
> > +     Value type: <string>
> > +     Definition: must be "qcom,msm8976-pinctrl"
> > +
> > +- reg:
> > +     Usage: required
> > +     Value type: <prop-encoded-array>
> > +     Definition: the base address and size of the TLMM register space.
> > +
> > +- interrupts:
> > +     Usage: required
> > +     Value type: <prop-encoded-array>
> > +     Definition: should specify the TLMM summary IRQ.
> > +
> > +- interrupt-controller:
> > +     Usage: required
> > +     Value type: <none>
> > +     Definition: identifies this node as an interrupt controller
> > +
> > +- #interrupt-cells:
> > +     Usage: required
> > +     Value type: <u32>
> > +     Definition: must be 2. Specifying the pin number and flags, as defined
> > +                 in <dt-bindings/interrupt-controller/irq.h>
> > +
> > +- gpio-controller:
> > +     Usage: required
> > +     Value type: <none>
> > +     Definition: identifies this node as a gpio controller
> > +
> > +- #gpio-cells:
> > +     Usage: required
> > +     Value type: <u32>
> > +     Definition: must be 2. Specifying the pin number and flags, as defined
> > +                 in <dt-bindings/gpio/gpio.h>
> > +
> > +- gpio-ranges:
> > +     Usage: required
> > +     Definition:  see ../gpio/gpio.txt
> > +
> > +- gpio-reserved-ranges:
> > +     Usage: optional
> > +     Definition: see ../gpio/gpio.txt
> > +
> > +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
> > +a general description of GPIO and interrupt bindings.
> > +
> > +Please refer to pinctrl-bindings.txt in this directory for details of the
> > +common pinctrl bindings used by client devices, including the meaning of the
> > +phrase "pin configuration node".
> > +
> > +The pin configuration nodes act as a container for an arbitrary number of
> > +subnodes. Each of these subnodes represents some desired configuration for a
> > +pin, a group, or a list of pins or groups. This configuration can include the
> > +mux function to select on those pin(s)/group(s), and various pin configuration
> > +parameters, such as pull-up, drive strength, etc.
> > +
> > +
> > +PIN CONFIGURATION NODES:
> > +
> > +The name of each subnode is not important; all subnodes should be enumerated
> > +and processed purely based on their content.
> > +
> > +Each subnode only affects those parameters that are explicitly listed. In
> > +other words, a subnode that lists a mux function but no pin configuration
> > +parameters implies no information about any pin configuration parameters.
> > +Similarly, a pin subnode that describes a pullup parameter implies no
> > +information about e.g. the mux function.
> > +
> > +
> > +The following generic properties as defined in pinctrl-bindings.txt are valid
> > +to specify in a pin configuration subnode:
> > +
> > +- pins:
> > +     Usage: required
> > +     Value type: <string-array>
> > +     Definition: List of gpio pins affected by the properties specified in
> > +                 this subnode.
> > +
> > +                 Valid pins are:
> > +                   gpio0-gpio145
> > +                     Supports mux, bias and drive-strength
> > +
> > +                   sdc1_clk, sdc1_cmd, sdc1_data,
> > +                   sdc2_clk, sdc2_cmd, sdc2_data,
> > +                   sdc3_clk, sdc3_cmd, sdc3_data
> > +                     Supports bias and drive-strength
> > +
> > +- function:
> > +     Usage: required
> > +     Value type: <string>
> > +     Definition: Specify the alternative function to be configured for the
> > +                 specified pins. Functions are only valid for gpio pins.
> > +                 Valid values are:
> > +
> > +                 gpio, blsp_uart1, blsp_spi1, smb_int, blsp_i2c1, blsp_spi2,
> > +                 blsp_uart2, blsp_i2c2, gcc_gp1_clk_b, blsp_spi3,
> > +                 qdss_tracedata_b, blsp_i2c3, gcc_gp2_clk_b, gcc_gp3_clk_b,
> > +                 blsp_spi4, cap_int, blsp_i2c4, blsp_spi5, blsp_uart5,
> > +                 qdss_traceclk_a, m_voc, blsp_i2c5, qdss_tracectl_a,
> > +                 qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b,
> > +                 blsp_i2c6, qdss_traceclk_b, mdp_vsync, pri_mi2s_mclk_a,
> > +                 sec_mi2s_mclk_a, cam_mclk, cci0_i2c, cci1_i2c, blsp1_spi,
> > +                 blsp3_spi, gcc_gp1_clk_a, gcc_gp2_clk_a, gcc_gp3_clk_a,
> > +                 uim_batt, sd_write, uim1_data, uim1_clk, uim1_reset,
> > +                 uim1_present, uim2_data, uim2_clk, uim2_reset,
> > +                 uim2_present, ts_xvdd, mipi_dsi0, us_euro, ts_resout,
> > +                 ts_sample, sec_mi2s_mclk_b, pri_mi2s, codec_reset,
> > +                 cdc_pdm0, us_emitter, pri_mi2s_mclk_b, pri_mi2s_mclk_c,
> > +                 lpass_slimbus, lpass_slimbus0, lpass_slimbus1, codec_int1,
> > +                 codec_int2, wcss_bt, sdc3, wcss_wlan2, wcss_wlan1,
> > +                 wcss_wlan0, wcss_wlan, wcss_fm, key_volp, key_snapshot,
> > +                 key_focus, key_home, pwr_down, dmic0_clk, hdmi_int,
> > +                 dmic0_data, wsa_vi, wsa_en, blsp_spi8, wsa_irq, blsp_i2c8,
> > +                 pa_indicator, modem_tsync, ssbi_wtr1, gsm1_tx, gsm0_tx,
> > +                 sdcard_det, sec_mi2s, ss_switch,
> > +
> > +- bias-disable:
> > +     Usage: optional
> > +     Value type: <none>
> > +     Definition: The specified pins should be configured as no pull.
> > +
> > +- bias-pull-down:
> > +     Usage: optional
> > +     Value type: <none>
> > +     Definition: The specified pins should be configured as pull down.
> > +
> > +- bias-pull-up:
> > +     Usage: optional
> > +     Value type: <none>
> > +     Definition: The specified pins should be configured as pull up.
> > +
> > +- output-high:
> > +     Usage: optional
> > +     Value type: <none>
> > +     Definition: The specified pins are configured in output mode, driven
> > +                 high.
> > +                 Not valid for sdc pins.
> > +
> > +- output-low:
> > +     Usage: optional
> > +     Value type: <none>
> > +     Definition: The specified pins are configured in output mode, driven
> > +                 low.
> > +                 Not valid for sdc pins.
> > +
> > +- drive-strength:
> > +     Usage: optional
> > +     Value type: <u32>
> > +     Definition: Selects the drive strength for the specified pins, in mA.
> > +                 Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
> > +
> > +Example:
> > +
> > +     tlmm: pinctrl@1000000 {
> > +             compatible = "qcom,msm8976-pinctrl";
> > +             reg = <0x1000000 0x300000>;
> > +             interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +             gpio-ranges = <&tlmm 0 0 145>;
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +
> > +             blsp1_uart2_active: blsp1_uart2_active {
> > +                     mux {
> > +                             pins = "gpio4", "gpio5", "gpio6", "gpio7";
> > +                             function = "blsp_uart2";
> > +                     };
> > +
> > +                     config {
> > +                             pins = "gpio4", "gpio5", "gpio6", "gpio7";
> > +                             drive-strength = <2>;
> > +                             bias-disable;
> > +                     };
> > +             };
> > +     };
> > --
> > 2.21.0
> >

Rob Herring (Arm) Oct. 15, 2019, 8:32 p.m. UTC | #3

On Sat,  5 Oct 2019 12:59:36 +0200, [e-mail] wrote:
> From: AngeloGioacchino Del Regno <[e-mail]>
> 
> Add the documentation for this new driver for pin configuration
> with the pinctrl framework on MSM8976/56 and its APQ variants.
> ---
>  .../bindings/pinctrl/qcom,msm8976-pinctrl.txt | 183 ++++++++++++++++++
>  1 file changed, 183 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
> 

Reviewed-by: Rob Herring <[e-mail]>

Linus Walleij Oct. 16, 2019, 1:53 p.m. UTC | #4

On Sat, Oct 5, 2019 at 12:59 PM <[e-mail]> wrote:

> From: AngeloGioacchino Del Regno <[e-mail]>
>
> Add the documentation for this new driver for pin configuration
> with the pinctrl framework on MSM8976/56 and its APQ variants.

Fixed up the tags including SoB and applied!

Thanks!
Linus Walleij

Patch

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
new file mode 100644
index 000000000000..70d04d12f136
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.txt
@@ -0,0 +1,183 @@ 
+Qualcomm MSM8976 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8956 and MSM8976 platforms.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,msm8976-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+- gpio-ranges:
+	Usage: required
+	Definition:  see ../gpio/gpio.txt
+
+- gpio-reserved-ranges:
+	Usage: optional
+	Definition: see ../gpio/gpio.txt
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.
+
+		    Valid pins are:
+		      gpio0-gpio145
+		        Supports mux, bias and drive-strength
+
+		      sdc1_clk, sdc1_cmd, sdc1_data,
+		      sdc2_clk, sdc2_cmd, sdc2_data,
+		      sdc3_clk, sdc3_cmd, sdc3_data
+		        Supports bias and drive-strength
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+
+		    gpio, blsp_uart1, blsp_spi1, smb_int, blsp_i2c1, blsp_spi2,
+		    blsp_uart2, blsp_i2c2, gcc_gp1_clk_b, blsp_spi3,
+		    qdss_tracedata_b, blsp_i2c3, gcc_gp2_clk_b, gcc_gp3_clk_b,
+		    blsp_spi4, cap_int, blsp_i2c4, blsp_spi5, blsp_uart5,
+		    qdss_traceclk_a, m_voc, blsp_i2c5, qdss_tracectl_a,
+		    qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b,
+		    blsp_i2c6, qdss_traceclk_b, mdp_vsync, pri_mi2s_mclk_a,
+		    sec_mi2s_mclk_a, cam_mclk, cci0_i2c, cci1_i2c, blsp1_spi,
+		    blsp3_spi, gcc_gp1_clk_a, gcc_gp2_clk_a, gcc_gp3_clk_a,
+		    uim_batt, sd_write, uim1_data, uim1_clk, uim1_reset,
+		    uim1_present, uim2_data, uim2_clk, uim2_reset,
+		    uim2_present, ts_xvdd, mipi_dsi0, us_euro, ts_resout,
+		    ts_sample, sec_mi2s_mclk_b, pri_mi2s, codec_reset,
+		    cdc_pdm0, us_emitter, pri_mi2s_mclk_b, pri_mi2s_mclk_c,
+		    lpass_slimbus, lpass_slimbus0, lpass_slimbus1, codec_int1,
+		    codec_int2, wcss_bt, sdc3, wcss_wlan2, wcss_wlan1,
+		    wcss_wlan0, wcss_wlan, wcss_fm, key_volp, key_snapshot,
+		    key_focus, key_home, pwr_down, dmic0_clk, hdmi_int,
+		    dmic0_data, wsa_vi, wsa_en, blsp_spi8, wsa_irq, blsp_i2c8,
+		    pa_indicator, modem_tsync, ssbi_wtr1, gsm1_tx, gsm0_tx,
+		    sdcard_det, sec_mi2s, ss_switch,
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+		    Not valid for sdc pins.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+		    Not valid for sdc pins.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	tlmm: pinctrl@1000000 {
+		compatible = "qcom,msm8976-pinctrl";
+		reg = <0x1000000 0x300000>;
+		interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-ranges = <&tlmm 0 0 145>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		blsp1_uart2_active: blsp1_uart2_active {
+			mux {
+				pins = "gpio4", "gpio5", "gpio6", "gpio7";
+				function = "blsp_uart2";
+			};
+
+			config {
+				pins = "gpio4", "gpio5", "gpio6", "gpio7";
+				drive-strength = <2>;
+				bias-disable;
+			};
+		};
+	};