ARM: dts: Add minimal support for Droid Bionic xt875
diff mbox series

Message ID 20191009222549.53265-1-tony@atomide.com
State New
Headers show
Series
  • ARM: dts: Add minimal support for Droid Bionic xt875
Related show

Commit Message

Tony Lindgren Oct. 9, 2019, 10:25 p.m. UTC
We already have folks booting Droid Bionic with Droid 4 dts, but it is
a different hardware with no keyboard.

Let's start adding device specific support for Droid bionic by making
current omap4-droid4-xt894 a common file and including it.

Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Comments

Pavel Machek Oct. 13, 2019, 2:33 p.m. UTC | #1
On Wed 2019-10-09 15:25:49, Tony Lindgren wrote:
> We already have folks booting Droid Bionic with Droid 4 dts, but it is
> a different hardware with no keyboard.
> 
> Let's start adding device specific support for Droid bionic by making
> current omap4-droid4-xt894 a common file and including it.
> 
> Cc: Merlijn Wajer <merlijn@wizzup.org>
> Cc: Pavel Machek <pavel@ucw.cz>

Acked-by: Pavel Machek <pavel@ucw.cz>

Patch
diff mbox series

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b21b3a64641a..7a61339b8049 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -765,6 +765,7 @@  dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-wega-rdk.dtb \
 	am335x-osd3358-sm-red.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += \
+	omap4-droid-bionic-xt875.dtb \
 	omap4-droid4-xt894.dtb \
 	omap4-duovero-parlor.dtb \
 	omap4-kc1.dtb \
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
similarity index 99%
copy from arch/arm/boot/dts/omap4-droid4-xt894.dts
copy to arch/arm/boot/dts/motorola-mapphone-common.dtsi
index 4454449de00c..ae543fb37494 100644
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
@@ -6,9 +6,6 @@ 
 #include "motorola-cpcap-mapphone.dtsi"
 
 / {
-	model = "Motorola Droid 4 XT894";
-	compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
-
 	chosen {
 		stdout-path = &uart3;
 	};
diff --git a/arch/arm/boot/dts/omap4-droid-bionic-xt875.dts b/arch/arm/boot/dts/omap4-droid-bionic-xt875.dts
new file mode 100644
index 000000000000..ba5c35b7027d
--- /dev/null
+++ b/arch/arm/boot/dts/omap4-droid-bionic-xt875.dts
@@ -0,0 +1,9 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-common.dtsi"
+
+/ {
+	model = "Motorola Droid Bionic XT875";
+	compatible = "motorola,droid-bionic", "ti,omap4430", "ti,omap4";
+};
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts
index 4454449de00c..c0d2fd92aea3 100644
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts
@@ -1,784 +1,9 @@ 
 // SPDX-License-Identifier: GPL-2.0-only
 /dts-v1/;
 
-#include <dt-bindings/input/input.h>
-#include "omap443x.dtsi"
-#include "motorola-cpcap-mapphone.dtsi"
+#include "motorola-mapphone-common.dtsi"
 
 / {
 	model = "Motorola Droid 4 XT894";
 	compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
-
-	chosen {
-		stdout-path = &uart3;
-	};
-
-	aliases {
-		display0 = &lcd0;
-		display1 = &hdmi0;
-	};
-
-	/*
-	 * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
-	 * then 1023 - 1024 seems to contain mbm.
-	 */
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x3fd00000>;	/* 1021 MB */
-	};
-
-	/* Poweroff GPIO probably connected to CPCAP */
-	gpio-poweroff {
-		compatible = "gpio-poweroff";
-		pinctrl-0 = <&poweroff_gpio>;
-		pinctrl-names = "default";
-		gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;	/* gpio50 */
-	};
-
-	hdmi0: connector {
-		compatible = "hdmi-connector";
-		pinctrl-0 = <&hdmi_hpd_gpio>;
-		pinctrl-names = "default";
-		label = "hdmi";
-		type = "d";
-
-		hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;	/* gpio63 */
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_out>;
-			};
-		};
-	};
-
-	/*
-	 * HDMI 5V regulator probably sourced from battery. Let's keep
-	 * keep this as always enabled for HDMI to work until we've
-	 * figured what the encoder chip is.
-	 */
-	hdmi_regulator: regulator-hdmi {
-		compatible = "regulator-fixed";
-		regulator-name = "hdmi";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>;	/* gpio59 */
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	/* FS USB Host PHY on port 1 for mdm6600 */
-	fsusb1_phy: usb-phy@1 {
-		compatible = "motorola,mapphone-mdm6600";
-		pinctrl-0 = <&usb_mdm6600_pins>;
-		pinctrl-names = "default";
-		enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
-		power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;	/* gpio_54 */
-		reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;	/* gpio_49 */
-		/* mode: gpio_148 gpio_149 */
-		motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
-				      <&gpio5 21 GPIO_ACTIVE_HIGH>;
-		/* cmd: gpio_103 gpio_104 gpio_142 */
-		motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
-				     <&gpio4 8 GPIO_ACTIVE_HIGH>,
-				     <&gpio5 14 GPIO_ACTIVE_HIGH>;
-		/* status: gpio_52 gpio_53 gpio_55 */
-		motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
-					<&gpio2 21 GPIO_ACTIVE_HIGH>,
-					<&gpio2 23 GPIO_ACTIVE_HIGH>;
-		#phy-cells = <0>;
-	};
-
-	/* HS USB host TLL nop-phy on port 2 for w3glte */
-	hsusb2_phy: usb-phy@2 {
-		compatible = "usb-nop-xceiv";
-		#phy-cells = <0>;
-	};
-
-	/* LCD regulator from sw5 source */
-	lcd_regulator: regulator-lcd {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd";
-		regulator-min-microvolt = <5050000>;
-		regulator-max-microvolt = <5050000>;
-		gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;	/* gpio96 */
-		enable-active-high;
-		vin-supply = <&sw5>;
-	};
-
-	/* This is probably coming straight from the battery.. */
-	wl12xx_vmmc: regulator-wl12xx {
-		compatible = "regulator-fixed";
-		regulator-name = "vwl1271";
-		regulator-min-microvolt = <1650000>;
-		regulator-max-microvolt = <1650000>;
-		gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;	/* gpio94 */
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-
-		volume_down {
-			label = "Volume Down";
-			gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
-			linux,code = <KEY_VOLUMEDOWN>;
-			linux,can-disable;
-			/* Value above 7.95ms for no GPIO hardware debounce */
-			debounce-interval = <10>;
-		};
-
-		slider {
-			label = "Keypad Slide";
-			gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_KEYPAD_SLIDE>;
-			linux,can-disable;
-			/* Value above 7.95ms for no GPIO hardware debounce */
-			debounce-interval = <10>;
-		};
-	};
-
-	soundcard {
-		compatible = "audio-graph-card";
-		label = "Droid 4 Audio";
-
-		simple-graph-card,widgets =
-			"Speaker", "Earpiece",
-			"Speaker", "Loudspeaker",
-			"Headphone", "Headphone Jack",
-			"Microphone", "Internal Mic";
-
-		simple-graph-card,routing =
-			"Earpiece", "EP",
-			"Loudspeaker", "SPKR",
-			"Headphone Jack", "HSL",
-			"Headphone Jack", "HSR",
-			"MICR", "Internal Mic";
-
-		dais = <&mcbsp2_port>, <&mcbsp3_port>;
-	};
-
-	pwm8: dmtimer-pwm-8 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&vibrator_direction_pin>;
-
-		compatible = "ti,omap-dmtimer-pwm";
-		#pwm-cells = <3>;
-		ti,timers = <&timer8>;
-		ti,clock-source = <0x01>;
-	};
-
-	pwm9: dmtimer-pwm-9 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&vibrator_enable_pin>;
-
-		compatible = "ti,omap-dmtimer-pwm";
-		#pwm-cells = <3>;
-		ti,timers = <&timer9>;
-		ti,clock-source = <0x01>;
-	};
-
-	vibrator {
-		compatible = "pwm-vibrator";
-		pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
-		pwm-names = "enable", "direction";
-		direction-duty-cycle-ns = <10000000>;
-	};
-};
-
-&dss {
-	status = "okay";
-};
-
-&dsi1 {
-	status = "okay";
-	vdd-supply = <&vcsi>;
-
-	port {
-		dsi1_out_ep: endpoint {
-			remote-endpoint = <&lcd0_in>;
-			lanes = <0 1 2 3 4 5>;
-		};
-	};
-
-	lcd0: display {
-		compatible = "panel-dsi-cm";
-		label = "lcd0";
-		vddi-supply = <&lcd_regulator>;
-		reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;	/* gpio101 */
-
-		width-mm = <50>;
-		height-mm = <89>;
-
-		panel-timing {
-			clock-frequency = <0>;		/* Calculated by dsi */
-
-			hback-porch = <2>;
-			hactive = <540>;
-			hfront-porch = <0>;
-			hsync-len = <2>;
-
-			vback-porch = <1>;
-			vactive = <960>;
-			vfront-porch = <0>;
-			vsync-len = <1>;
-
-			hsync-active = <0>;
-			vsync-active = <0>;
-			de-active = <1>;
-			pixelclk-active = <1>;
-		};
-
-		port {
-			lcd0_in: endpoint {
-				remote-endpoint = <&dsi1_out_ep>;
-			};
-		};
-	};
-};
-
-&hdmi {
-	status = "okay";
-	pinctrl-0 = <&dss_hdmi_pins>;
-	pinctrl-names = "default";
-	vdda-supply = <&vdac>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&hdmi_connector_in>;
-			lanes = <1 0 3 2 5 4 7 6>;
-		};
-	};
-};
-
-&i2c1 {
-	tmp105@48 {
-		compatible = "ti,tmp105";
-		reg = <0x48>;
-		pinctrl-0 = <&tmp105_irq>;
-		pinctrl-names = "default";
-		/* kpd_row0.gpio_178 */
-		interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
-				       &omap4_pmx_core 0x14e>;
-		interrupt-names = "irq", "wakeup";
-		wakeup-source;
-	};
-};
-
-&keypad {
-	keypad,num-rows = <8>;
-	keypad,num-columns = <8>;
-	linux,keymap = <
-
-	/* Row 1 */
-	MATRIX_KEY(0, 2, KEY_1)
-	MATRIX_KEY(0, 6, KEY_2)
-	MATRIX_KEY(2, 3, KEY_3)
-	MATRIX_KEY(0, 7, KEY_4)
-	MATRIX_KEY(0, 4, KEY_5)
-	MATRIX_KEY(5, 5, KEY_6)
-	MATRIX_KEY(0, 1, KEY_7)
-	MATRIX_KEY(0, 5, KEY_8)
-	MATRIX_KEY(0, 0, KEY_9)
-	MATRIX_KEY(1, 6, KEY_0)
-
-	/* Row 2 */
-	MATRIX_KEY(3, 4, KEY_APOSTROPHE)
-	MATRIX_KEY(7, 6, KEY_Q)
-	MATRIX_KEY(7, 7, KEY_W)
-	MATRIX_KEY(7, 2, KEY_E)
-	MATRIX_KEY(1, 0, KEY_R)
-	MATRIX_KEY(4, 4, KEY_T)
-	MATRIX_KEY(1, 2, KEY_Y)
-	MATRIX_KEY(6, 7, KEY_U)
-	MATRIX_KEY(2, 2, KEY_I)
-	MATRIX_KEY(5, 6, KEY_O)
-	MATRIX_KEY(3, 7, KEY_P)
-	MATRIX_KEY(6, 5, KEY_BACKSPACE)
-
-	/* Row 3 */
-	MATRIX_KEY(5, 4, KEY_TAB)
-	MATRIX_KEY(5, 7, KEY_A)
-	MATRIX_KEY(2, 7, KEY_S)
-	MATRIX_KEY(7, 0, KEY_D)
-	MATRIX_KEY(2, 6, KEY_F)
-	MATRIX_KEY(6, 2, KEY_G)
-	MATRIX_KEY(6, 6, KEY_H)
-	MATRIX_KEY(1, 4, KEY_J)
-	MATRIX_KEY(3, 1, KEY_K)
-	MATRIX_KEY(2, 1, KEY_L)
-	MATRIX_KEY(4, 6, KEY_ENTER)
-
-	/* Row 4 */
-	MATRIX_KEY(3, 6, KEY_LEFTSHIFT)		/* KEY_CAPSLOCK */
-	MATRIX_KEY(6, 1, KEY_Z)
-	MATRIX_KEY(7, 4, KEY_X)
-	MATRIX_KEY(5, 1, KEY_C)
-	MATRIX_KEY(1, 7, KEY_V)
-	MATRIX_KEY(2, 4, KEY_B)
-	MATRIX_KEY(4, 1, KEY_N)
-	MATRIX_KEY(1, 1, KEY_M)
-	MATRIX_KEY(3, 5, KEY_COMMA)
-	MATRIX_KEY(5, 2, KEY_DOT)
-	MATRIX_KEY(6, 3, KEY_UP)
-	MATRIX_KEY(7, 3, KEY_OK)
-
-	/* Row 5 */
-	MATRIX_KEY(2, 5, KEY_LEFTCTRL)		/* KEY_LEFTSHIFT */
-	MATRIX_KEY(4, 5, KEY_LEFTALT)		/* SYM */
-	MATRIX_KEY(6, 0, KEY_MINUS)
-	MATRIX_KEY(4, 7, KEY_EQUAL)
-	MATRIX_KEY(1, 5, KEY_SPACE)
-	MATRIX_KEY(3, 2, KEY_SLASH)
-	MATRIX_KEY(4, 3, KEY_LEFT)
-	MATRIX_KEY(5, 3, KEY_DOWN)
-	MATRIX_KEY(3, 3, KEY_RIGHT)
-
-	/* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
-	MATRIX_KEY(5, 0, KEY_VOLUMEUP)
-	>;
-};
-
-&mmc1 {
-	vmmc-supply = <&vwlan2>;
-	bus-width = <4>;
-	cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;	/* gpio176 */
-};
-
-&mmc2 {
-	vmmc-supply = <&vsdio>;
-	bus-width = <8>;
-	ti,non-removable;
-};
-
-&mmc3 {
-	vmmc-supply = <&wl12xx_vmmc>;
-	/* uart2_tx.sdmmc3_dat1 pad as wakeirq */
-	interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core 0xde>;
-	interrupt-names = "irq", "wakeup";
-	non-removable;
-	bus-width = <4>;
-	cap-power-off-card;
-	keep-power-in-suspend;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-	wlcore: wlcore@2 {
-		compatible = "ti,wl1285", "ti,wl1283";
-		reg = <2>;
-		/* gpio_100 with gpmc_wait2 pad as wakeirq */
-		interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>,
-				      <&omap4_pmx_core 0x4e>;
-		interrupt-names = "irq", "wakeup";
-		ref-clock-frequency = <26000000>;
-		tcxo-clock-frequency = <26000000>;
-	};
-};
-
-&i2c1 {
-	led-controller@38 {
-		compatible = "ti,lm3532";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x38>;
-
-		enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
-
-		ramp-up-us = <1024>;
-		ramp-down-us = <8193>;
-
-		led@0 {
-			reg = <0>;
-			led-sources = <2>;
-			ti,led-mode = <0>;
-			label = ":backlight";
-			linux,default-trigger = "backlight";
-		};
-
-		led@1 {
-			reg = <1>;
-			led-sources = <1>;
-			ti,led-mode = <0>;
-			label = ":kbd_backlight";
-		};
-	};
-};
-
-&i2c2 {
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&touchscreen_pins>;
-
-		reset-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio173 */
-
-		/* gpio_183 with sys_nirq2 pad as wakeup */
-		interrupts-extended = <&gpio6 23 IRQ_TYPE_EDGE_FALLING>,
-				      <&omap4_pmx_core 0x160>;
-		interrupt-names = "irq", "wakeup";
-		wakeup-source;
-	};
-
-	isl29030@44 {
-		compatible = "isil,isl29030";
-		reg = <0x44>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&als_proximity_pins>;
-
-		interrupt-parent = <&gpio6>;
-		interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
-	};
-};
-
-&omap4_pmx_core {
-
-	/* hdmi_hpd.gpio_63 */
-	hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
-		>;
-	};
-
-	/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
-	dss_hdmi_pins: pinmux_dss_hdmi_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
-		OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
-		OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
-		>;
-	};
-
-	/* gpmc_ncs0.gpio_50 */
-	poweroff_gpio: pinmux_poweroff_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	/* kpd_row0.gpio_178 */
-	tmp105_irq: pinmux_tmp105_irq {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
-		/* gpio_60 */
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
-		>;
-	};
-
-	touchscreen_pins: pinmux_touchscreen_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	als_proximity_pins: pinmux_als_proximity_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
-		pinctrl-single,pins = <
-		/* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
-		OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
-
-		/* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
-		OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
-
-		/* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
-		OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
-
-		/* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
-		OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
-
-		/* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
-		OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
-
-		/* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
-		OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
-
-		/* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
-		OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
-
-		/* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
-		OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
-
-		/* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
-		OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
-
-		/* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
-		OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
-
-		/* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
-		OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
-		>;
-	};
-
-	usb_ulpi_pins: pinmux_usb_ulpi_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x196, MUX_MODE7)
-		OMAP4_IOPAD(0x198, MUX_MODE7)
-		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
-		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
-		>;
-	};
-
-	/* usb0_otg_dp and usb0_otg_dm */
-	usb_utmi_pins: pinmux_usb_utmi_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
-		OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
-		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
-		>;
-	};
-
-	/*
-	 * Note that the v3.0.8 stock userspace dynamically remuxes uart1
-	 * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
-	 * when not used. If needed, we can add rts pin remux later based
-	 * on power measurements.
-	 */
-	uart1_pins: pinmux_uart1_pins {
-		pinctrl-single,pins = <
-		/* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
-		OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
-
-		/* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
-		OMAP4_IOPAD(0x13e, MUX_MODE1)
-
-		/* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
-		OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
-
-		/* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
-		OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
-		>;
-	};
-
-	/* uart3_tx_irtx and uart3_rx_irrx */
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x196, MUX_MODE7)
-		OMAP4_IOPAD(0x198, MUX_MODE7)
-		OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1ba, MUX_MODE2)
-		OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
-		OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
-		OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
-		>;
-	};
-
-	uart4_pins: pinmux_uart4_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0)		/* uart4_rx */
-		OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0)		/* uart4_tx */
-		OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5)	/* uart4_cts */
-		OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5)	/* uart4_rts */
-		>;
-	};
-
-	mcbsp2_pins: pinmux_mcbsp2_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_clkx */
-		OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_dr */
-		OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0)	/* abe_mcbsp2_dx */
-		OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)	/* abe_mcbsp2_fsx */
-		>;
-	};
-
-	mcbsp3_pins: pinmux_mcbsp3_pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_dr */
-		OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1)	/* abe_mcbsp3_dx */
-		OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_clkx */
-		OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_fsx */
-		>;
-	};
-
-	vibrator_direction_pin: pinmux_vibrator_direction_pin {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1)	/* dmtimer8_pwm_evt (gpio_27) */
-		>;
-	};
-
-	vibrator_enable_pin: pinmux_vibrator_enable_pin {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)	/* dmtimer9_pwm_evt (gpio_28) */
-		>;
-	};
-};
-
-&omap4_pmx_wkup {
-	usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
-		/* gpio_wk0 */
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
-		>;
-	};
-};
-
-/* Configure pwm clock source for timers 8 & 9 */
-&timer8 {
-	assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
-	assigned-clock-parents = <&sys_clkin_ck>;
-};
-
-&timer9 {
-	assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
-	assigned-clock-parents = <&sys_clkin_ck>;
-};
-
-/*
- * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
- * uart1 wakeirq.
- */
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>;
-	interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core 0xfc>;
-};
-
-&uart3 {
-	interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core 0x17c>;
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart4_pins>;
-
-	bluetooth {
-		compatible = "ti,wl1285-st";
-		enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
-		max-speed = <3686400>;
-	};
-};
-
-&usbhsohci {
-	phys = <&fsusb1_phy>;
-	phy-names = "usb";
-};
-
-&usbhsehci {
-	phys = <&hsusb2_phy>;
-};
-
-&usbhshost {
-	port1-mode = "ohci-phy-4pin-dpdm";
-	port2-mode = "ehci-tll";
-};
-
-/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
-&usb_otg_hs {
-	interface-type = <1>;
-	mode = <3>;
-	power = <50>;
-};
-
-&i2c4 {
-	ak8975: magnetometer@c {
-		compatible = "asahi-kasei,ak8975";
-		reg = <0x0c>;
-
-		vdd-supply = <&vhvio>;
-
-		interrupt-parent = <&gpio6>;
-		interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
-
-		rotation-matrix = "-1", "0", "0",
-				  "0", "1", "0",
-				  "0", "0", "-1";
-
-	};
-
-	lis3dh: accelerometer@18 {
-		compatible = "st,lis3dh-accel";
-		reg = <0x18>;
-
-		vdd-supply = <&vhvio>;
-
-		interrupt-parent = <&gpio2>;
-		interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
-
-		rotation-matrix = "0", "-1", "0",
-				  "1", "0", "0",
-				  "0", "0", "1";
-	};
-};
-
-&mcbsp2 {
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp2_pins>;
-	status = "okay";
-
-	mcbsp2_port: port {
-		cpu_dai2: endpoint {
-			dai-format = "i2s";
-			remote-endpoint = <&cpcap_audio_codec0>;
-			frame-master = <&cpcap_audio_codec0>;
-			bitclock-master = <&cpcap_audio_codec0>;
-		};
-	};
-};
-
-&mcbsp3 {
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcbsp3_pins>;
-	status = "okay";
-
-	mcbsp3_port: port {
-		cpu_dai3: endpoint {
-			dai-format = "dsp_a";
-			frame-master = <&cpcap_audio_codec1>;
-			bitclock-master = <&cpcap_audio_codec1>;
-			remote-endpoint = <&cpcap_audio_codec1>;
-		};
-	};
-};
-
-&cpcap_audio_codec0 {
-	remote-endpoint = <&cpu_dai2>;
-};
-
-&cpcap_audio_codec1 {
-	remote-endpoint = <&cpu_dai3>;
 };