diff mbox series

[5/5] media: atmel: atmel-isc-base: initialize the try_crop for the pads in try_fmt

Message ID 1574670712-31992-6-git-send-email-eugen.hristev@microchip.com (mailing list archive)
State New, archived
Headers show
Series media: atmel: atmel-isc-base: fixes for GREY/mt9v022 support | expand

Commit Message

Eugen Hristev Nov. 25, 2019, 8:32 a.m. UTC 
From: Eugen Hristev <eugen.hristev@microchip.com>

When requesting format from sensor, some sensors call the subdev_get_try_crop
which for ISC was not properly initialized, and this causes errors in
determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt to
obtain the framesize for this format from sensor.
In case this fails, use the maximum ISC width/height as try_crop, otherwise
provide the first size height/width from the sensor.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
---
 drivers/media/platform/atmel/atmel-isc-base.c | 33 +++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)
diff mbox series

Patch

diff --git a/drivers/media/platform/atmel/atmel-isc-base.c b/drivers/media/platform/atmel/atmel-isc-base.c
index 1bb1dd5..511f0c5 100644
--- a/drivers/media/platform/atmel/atmel-isc-base.c
+++ b/drivers/media/platform/atmel/atmel-isc-base.c
@@ -1233,6 +1233,36 @@  static int isc_try_configure_pipeline(struct isc_device *isc)
 	return 0;
 }
 
+static void isc_try_fse(struct isc_device *isc,
+			struct v4l2_subdev_pad_config *pad_cfg)
+{
+	int ret;
+	struct v4l2_subdev_frame_size_enum fse = {0};
+	/*
+	 * If we do not know yet which format the subdev is using, we cannot
+	 * do anything.
+	 */
+	if (!isc->try_config.sd_format)
+		return;
+
+	fse.code = isc->try_config.sd_format->mbus_code;
+	fse.which = V4L2_SUBDEV_FORMAT_TRY;
+
+	ret = v4l2_subdev_call(isc->current_subdev->sd, pad, enum_frame_size,
+			       pad_cfg, &fse);
+	/*
+	 * Attempt to obtain format size from subdev. If not available,
+	 * just use the maximum ISC can receive.
+	 */
+	if (ret) {
+		pad_cfg->try_crop.width = ISC_MAX_SUPPORT_WIDTH;
+		pad_cfg->try_crop.height = ISC_MAX_SUPPORT_HEIGHT;
+	} else {
+		pad_cfg->try_crop.width = fse.max_width;
+		pad_cfg->try_crop.height = fse.max_height;
+	}
+}
+
 static int isc_try_fmt(struct isc_device *isc, struct v4l2_format *f,
 			u32 *code)
 {
@@ -1336,6 +1366,9 @@  static int isc_try_fmt(struct isc_device *isc, struct v4l2_format *f,
 	if (ret)
 		goto isc_try_fmt_err;
 
+	/* Obtain frame sizes if possible to have crop requirements ready */
+	isc_try_fse(isc, &pad_cfg);
+
 	v4l2_fill_mbus_format(&format.format, pixfmt, mbus_code);
 	ret = v4l2_subdev_call(isc->current_subdev->sd, pad, set_fmt,
 			       &pad_cfg, &format);