ARM: dts: mvebu: add support for SolidRun Clearfog GTR
diff mbox series

Message ID 3a870e11b152e2f8ffb2b3256c5ac42741658c4c.1574960406.git.baruch@tkos.co.il
State New
Headers show
Series
  • ARM: dts: mvebu: add support for SolidRun Clearfog GTR
Related show

Commit Message

Baruch Siach Nov. 28, 2019, 5 p.m. UTC
SolidRun Clearfog GTR L8 and S4 SBCs are based on Armada 385. They
features 8 (L8) or 4 (S4) switched Ethernet ports, 1 1Gb Ethernet port,
1 directly connected SFP port, 1 SFP port behind the switch (not
currently described in DT), 3 mini-PCIe slots, eMMC, SPI flash, USB3
port.

  https://developer.solid-run.com/products/clearfog-gtr-a385/

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
---
 arch/arm/boot/dts/Makefile                    |   2 +
 .../boot/dts/armada-385-clearfog-gtr-l8.dts   | 111 +++++
 .../boot/dts/armada-385-clearfog-gtr-s4.dts   |  75 +++
 .../arm/boot/dts/armada-385-clearfog-gtr.dtsi | 443 ++++++++++++++++++
 4 files changed, 631 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts
 create mode 100644 arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts
 create mode 100644 arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi

Comments

Andrew Lunn Nov. 29, 2019, 5:07 p.m. UTC | #1
On Thu, Nov 28, 2019 at 07:00:06PM +0200, Baruch Siach wrote:
> SolidRun Clearfog GTR L8 and S4 SBCs are based on Armada 385. They
> features 8 (L8) or 4 (S4) switched Ethernet ports, 1 1Gb Ethernet port,
> 1 directly connected SFP port, 1 SFP port behind the switch (not
> currently described in DT),

Hi Baruch

Did you try to add the SFP on the switch? What problems did you have?
The general support for it should be there.

> +			i2c@11100 { /* SFP */
> +				pinctrl-0 = <&cf_gtr_i2c1_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};

Since there are two SFPs, it would be a good idea to indicate which
one this is.

> +	sfp: sfp {
> +		compatible = "sff,sfp";
> +		i2c-bus = <&i2c1>;
> +		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
> +		mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>;
> +		tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
> +	};

when you get the second sfp working you are going to have naming
issue. So maybe call this sfp0?

> +		led1 {
> +			label = "led1";
> +			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		led2 {
> +			label = "led2";
> +			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
> +		};

There is a naming convention of LEDS labels. This does not fit it.

> +&gpio0 {
> +	pinctrl-0 = <&cf_gtr_fan_pwm>;
> +	pinctrl-names = "default";
> +
> +	wifi-disable {
> +		gpio-hog;
> +		gpios = <30 GPIO_ACTIVE_LOW>, <31 GPIO_ACTIVE_LOW>;
> +		output-low;
> +		line-name = "wifi-disable";
> +	};
> +};

Isn't there a generic rfkill GPIO driver? Never looked, but it seems
like it should exist.

> +	sar-isolation {
> +		gpio-hog;
> +		gpios = <15 GPIO_ACTIVE_LOW>;
> +		output-low;
> +		line-name = "sar-isolation";
> +	};

What is SAR?

     Andrew
Baruch Siach Dec. 1, 2019, 6:46 a.m. UTC | #2
Hi Andrew,

Thanks for your review.

On Fri, Nov 29 2019, Andrew Lunn wrote:

> On Thu, Nov 28, 2019 at 07:00:06PM +0200, Baruch Siach wrote:
>> SolidRun Clearfog GTR L8 and S4 SBCs are based on Armada 385. They
>> features 8 (L8) or 4 (S4) switched Ethernet ports, 1 1Gb Ethernet port,
>> 1 directly connected SFP port, 1 SFP port behind the switch (not
>> currently described in DT),
>
> Hi Baruch
>
> Did you try to add the SFP on the switch? What problems did you have?
> The general support for it should be there.

I have not tested this SFP yet.

>> +			i2c@11100 { /* SFP */
>> +				pinctrl-0 = <&cf_gtr_i2c1_pins>;
>> +				pinctrl-names = "default";
>> +				status = "okay";
>> +			};
>
> Since there are two SFPs, it would be a good idea to indicate which
> one this is.

This port is marked CON5/CON6 on the PCB. I'll extend the comment in v2.

>> +	sfp: sfp {
>> +		compatible = "sff,sfp";
>> +		i2c-bus = <&i2c1>;
>> +		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
>> +		mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>;
>> +		tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
>> +	};
>
> when you get the second sfp working you are going to have naming
> issue. So maybe call this sfp0?

Good idea.

>> +		led1 {
>> +			label = "led1";
>> +			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
>> +		};
>> +
>> +		led2 {
>> +			label = "led2";
>> +			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
>> +		};
>
> There is a naming convention of LEDS labels. This does not fit it.

Indeed. The 'label' property is deprecated since commit
c5d18dd6b64. These are general propose GPIOs. Not sure what 'function'
property fits here. Also, these GPIOs go out to an optional front-panel
connector. The 'color' property does not make much sense in that
case. I'll stick LED_COLOR_ID_GREEN for the no front-panel option.

>> +&gpio0 {
>> +	pinctrl-0 = <&cf_gtr_fan_pwm>;
>> +	pinctrl-names = "default";
>> +
>> +	wifi-disable {
>> +		gpio-hog;
>> +		gpios = <30 GPIO_ACTIVE_LOW>, <31 GPIO_ACTIVE_LOW>;
>> +		output-low;
>> +		line-name = "wifi-disable";
>> +	};
>> +};
>
> Isn't there a generic rfkill GPIO driver? Never looked, but it seems
> like it should exist.

Over the years there were attempts to add DT binding to rfkill-regulator
or rfkill-gpio:

  https://patchwork.kernel.org/patch/9407171/

  http://lists.infradead.org/pipermail/linux-arm-kernel/2014-April/247328.html

  https://www.spinics.net/lists/linux-wireless/msg84462.html

Not sure what is the right way to let userspace know about GPIO that
serves as rfkill.

>> +	sar-isolation {
>> +		gpio-hog;
>> +		gpios = <15 GPIO_ACTIVE_LOW>;
>> +		output-low;
>> +		line-name = "sar-isolation";
>> +	};
>
> What is SAR?

Sample at Reset. That's the Armada 38x datasheet term. This GPIO is
active at reset time to isolate SAR signals from interference of
external devices. We deassert isolation after reset to make these signal
usable.

baruch

--
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -
Andrew Lunn Dec. 1, 2019, 5:07 p.m. UTC | #3
Hi Baruch

> >> +	sar-isolation {
> >> +		gpio-hog;
> >> +		gpios = <15 GPIO_ACTIVE_LOW>;
> >> +		output-low;
> >> +		line-name = "sar-isolation";
> >> +	};
> >
> > What is SAR?
> 
> Sample at Reset. That's the Armada 38x datasheet term.

So this is pretty specific to Marvell. Maybe a comment would be good,
explaining what it is doing.

Thanks
	Andrew

Patch
diff mbox series

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b21b3a64641a..ff25a3e10567 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1227,6 +1227,8 @@  dtb-$(CONFIG_MACH_ARMADA_370) += \
 dtb-$(CONFIG_MACH_ARMADA_375) += \
 	armada-375-db.dtb
 dtb-$(CONFIG_MACH_ARMADA_38X) += \
+	armada-385-clearfog-gtr-s4.dtb \
+	armada-385-clearfog-gtr-l8.dtb \
 	armada-385-db-88f6820-amc.dtb \
 	armada-385-db-ap.dtb \
 	armada-385-linksys-caiman.dtb \
diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts b/arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts
new file mode 100644
index 000000000000..0cf958696453
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts
@@ -0,0 +1,111 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include "armada-385-clearfog-gtr.dtsi"
+
+&mdio {
+	switch0: switch0@4 {
+		compatible = "marvell,mv88e6190";
+		reg = <4>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cf_gtr_switch_reset_pins>;
+		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+				label = "lan8";
+				phy-handle = <&switch0phy0>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan7";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan6";
+				phy-handle = <&switch0phy2>;
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan5";
+				phy-handle = <&switch0phy3>;
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "lan4";
+				phy-handle = <&switch0phy4>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "lan3";
+				phy-handle = <&switch0phy5>;
+			};
+
+			port@7 {
+				reg = <7>;
+				label = "lan2";
+				phy-handle = <&switch0phy6>;
+			};
+
+			port@8 {
+				reg = <8>;
+				label = "lan1";
+				phy-handle = <&switch0phy7>;
+			};
+
+			port@10 {
+				reg = <10>;
+				label = "cpu";
+				ethernet = <&eth1>;
+			};
+
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: switch0phy0@1 {
+				reg = <0x1>;
+			};
+
+			switch0phy1: switch0phy1@2 {
+				reg = <0x2>;
+			};
+
+			switch0phy2: switch0phy2@3 {
+				reg = <0x3>;
+			};
+
+			switch0phy3: switch0phy3@4 {
+				reg = <0x4>;
+			};
+
+			switch0phy4: switch0phy4@5 {
+				reg = <0x5>;
+			};
+
+			switch0phy5: switch0phy5@6 {
+				reg = <0x6>;
+			};
+
+			switch0phy6: switch0phy6@7 {
+				reg = <0x7>;
+			};
+
+			switch0phy7: switch0phy7@8 {
+				reg = <0x8>;
+			};
+		};
+
+	};
+};
diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts b/arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts
new file mode 100644
index 000000000000..815bbd3f29e7
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts
@@ -0,0 +1,75 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include "armada-385-clearfog-gtr.dtsi"
+
+&sfp {
+	tx-fault-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
+};
+
+&mdio {
+	switch0: switch0@4 {
+		compatible = "marvell,mv88e6085";
+		reg = <4>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cf_gtr_switch_reset_pins>;
+		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+				label = "lan2";
+				phy-handle = <&switch0phy0>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan1";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan4";
+				phy-handle = <&switch0phy2>;
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan3";
+				phy-handle = <&switch0phy3>;
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&eth1>;
+			};
+
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: switch0phy0@11 {
+				reg = <0x11>;
+			};
+
+			switch0phy1: switch0phy1@12 {
+				reg = <0x12>;
+			};
+
+			switch0phy2: switch0phy2@13 {
+				reg = <0x13>;
+			};
+
+			switch0phy3: switch0phy3@14 {
+				reg = <0x14>;
+			};
+		};
+
+	};
+};
diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi b/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
new file mode 100644
index 000000000000..8c07ef46889b
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
@@ -0,0 +1,443 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Clearfog GTR machines rev 1.0 (88F6825)
+ *
+ *  Rabeeh Khoury <rabeeh@solid-run.com>, based on Russell King clearfog work
+ */
+
+/*
+	SERDES mapping -
+	0. SATA1 on CON18, or optionally mini PCIe CON3 - PCIe0
+	1. 6141 switch (2.5Gbps capable)
+	2. SATA0 on CON17, or optionally mini PCIe CON4 - PCIe1
+	3. USB 3.0 Host
+	4. mini PCIe CON2 - PCIe2
+	5. SFP connector, or optionally SGMII Ethernet 1512 PHY
+
+	USB 2.0 mapping -
+	0. USB 2.0 - 0 USB pins header CON12
+	1. USB 2.0 - 1 mini PCIe CON2
+	2. USB 2.0 - 2 to USB 3.0 connector (used with SERDES #3)
+
+	Pin mapping -
+	0,1 - console UART
+	2,3 - I2C0 - connected to I2C EEPROM, two temperature sensors,
+	      front panel and PSE controller
+	4,5 - MDC/MDIO
+	6..17 - RGMII
+	18 - Topaz switch reset (active low)
+	19 - 1512 phy reset
+	20 - 1512 phy reset (eth2, optional)
+	21,28,37,38,39,40 - SD0
+	22 - USB 3.0 current limiter enable (active high)
+	24 - SFP TX fault (input active high)
+	25 - SFP present (input active low)
+	26,27 - I2C1 - connected to SFP
+	29 - Fan PWM
+	30 - CON4 mini PCIe wifi disable
+	31 - CON3 mini PCIe wifi disable
+	32 - Fuse programming power toggle (1.8v)
+	33 - CON4 mini PCIe reset
+	34 - CON2 mini PCIe wifi disable
+	35 - CON3 mini PCIe reset
+	36 - Rear button (GPIO active low)
+	41 - CON1 front panel connector
+	42 - Front LED1, or front panel CON1
+	43 - Micron L-PBGA 24 ball SPI (1Gb) CS, or TPM SPI CS
+	44 - CON2 mini PCIe reset
+	45 - TPM PIRQ signal, or front panel CON1
+	46 - SFP TX disable
+	47 - Control isolation of boot sensitive SAR signals
+	48 - PSE reset
+	49 - PSE OSS signal
+	50 - PSE interrupt
+	52 - Front LED2, or front panel
+	53 - Front button
+	54 - SFP LOS (input active high)
+	55 - Fan sense
+	56(mosi),57(clk),58(miso) - SPI interface - 32Mb SPI, 1Gb SPI and TPM
+	59 - SPI 32Mb W25Q32BVZPIG CS0 chip select (bootable)
+*/
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-385.dtsi"
+
+/ {
+	model = "Clearfog GTR";
+	compatible = "marvell,armada385", "marvell,armada380";
+
+	aliases {
+		/* So that mvebu u-boot can update the MAC addresses */
+		ethernet1 = &eth0;
+		ethernet2 = &eth1;
+		ethernet3 = &eth2;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>; /* 256 MB */
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "5P0V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	v_usb3_con: regulator-v-usb3-con {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 22 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cf_gtr_usb3_con_vbus>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "v_usb3_con";
+		vin-supply = <&reg_5p0v>;
+		regulator-boot-on;
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+		internal-regs {
+
+			rtc@a3800 {
+				status = "okay";
+			};
+
+			i2c@11000 { /* ROM, temp sensor and front panel */
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			i2c@11100 { /* SFP */
+				pinctrl-0 = <&cf_gtr_i2c1_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			pinctrl@18000 {
+				cf_gtr_switch_reset_pins: cf-gtr-switch-reset-pins {
+					marvell,pins = "mpp18";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_usb3_con_vbus: cf-gtr-usb3-con-vbus {
+					marvell,pins = "mpp22";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_fan_pwm: cf-gtr-fan-pwm {
+					marvell,pins = "mpp23";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_i2c1_pins: i2c1-pins {
+					/* SFP */
+					marvell,pins = "mpp26", "mpp27";
+					marvell,function = "i2c1";
+				};
+
+				cf_gtr_sdhci_pins: cf-gtr-sdhci-pins {
+					marvell,pins = "mpp21", "mpp28",
+						       "mpp37", "mpp38",
+						       "mpp39", "mpp40";
+					marvell,function = "sd0";
+				};
+
+				cf_gtr_isolation_pins: cf-gtr-isolation-pins {
+					marvell,pins = "mpp47";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_poe_reset_pins: cf-gtr-poe-reset-pins {
+					marvell,pins = "mpp48";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_spi1_cs_pins: spi1-cs-pins {
+					marvell,pins = "mpp59";
+					marvell,function = "spi1";
+				};
+
+				cf_gtr_front_button_pins: cf-gtr-front-button-pins {
+					marvell,pins = "mpp53";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_rear_button_pins: cf-gtr-rear-button-pins {
+					marvell,pins = "mpp36";
+					marvell,function = "gpio";
+				};
+			};
+
+			sdhci@d8000 {
+				bus-width = <4>;
+				no-1-8-v;
+				non-removable;
+				pinctrl-0 = <&cf_gtr_sdhci_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				vmmc = <&reg_3p3v>;
+				wp-inverted;
+			};
+
+			usb@58000 {
+				status = "okay";
+			};
+
+			usb3@f0000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				vbus-supply = <&v_usb3_con>;
+				status = "okay";
+			};
+		};
+
+		pcie {
+			status = "okay";
+			/*
+			 * The PCIe units are accessible through
+			 * the mini-PCIe connectors on the board.
+			 */
+			pcie@1,0 {
+				reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+
+			pcie@2,0 {
+				reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+
+			pcie@3,0 {
+				reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+		};
+	};
+
+	sfp: sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&cf_gtr_rear_button_pins &cf_gtr_front_button_pins>;
+		pinctrl-names = "default";
+
+		button_0 {
+			label = "Rear Button";
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+			linux,can-disable;
+			linux,code = <BTN_0>;
+		};
+
+		button_1 {
+			label = "Front Button";
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+			linux,can-disable;
+			linux,code = <BTN_1>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&bm {
+	status = "okay";
+};
+
+&bm_bppi {
+	status = "okay";
+};
+
+&eth0 {
+	/* ethernet@70000 */
+	pinctrl-0 = <&ge0_rgmii_pins>;
+	pinctrl-names = "default";
+	phy = <&phy_dedicated>;
+	phy-mode = "rgmii-id";
+	buffer-manager = <&bm>;
+	bm,pool-long = <0>;
+	bm,pool-short = <1>;
+	status = "okay";
+};
+
+&eth1 {
+	/* ethernet@30000 */
+	bm,pool-long = <2>;
+	bm,pool-short = <1>;
+	buffer-manager = <&bm>;
+	phys = <&comphy1 1>;
+	phy-mode = "2500base-x";
+	status = "okay";
+
+	fixed-link {
+		speed = <2500>;
+		full-duplex;
+	};
+};
+
+&eth2 {
+	/* ethernet@34000 */
+	bm,pool-long = <3>;
+	bm,pool-short = <1>;
+	buffer-manager = <&bm>;
+	managed = "in-band-status";
+	phys = <&comphy5 1>;
+	phy-mode = "sgmii";
+	sfp = <&sfp>;
+	status = "okay";
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+	status = "okay";
+
+	phy_dedicated: ethernet-phy@0 {
+		/*
+		 * Annoyingly, the marvell phy driver configures the LED
+		 * register, rather than preserving reset-loaded setting.
+		 * We undo that rubbish here.
+		 */
+		marvell,reg-init = <3 16 0 0x1017>;
+		reg = <0>;
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&spi1 {
+	/*
+	 * CS0: W25Q32 flash
+	 */
+	pinctrl-0 = <&spi1_pins &cf_gtr_spi1_cs_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "w25q32", "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <3000000>;
+		status = "okay";
+	};
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* U26 temperature sensor placed near SoC */
+	temp1: nct75@4c {
+		compatible = "lm75";
+		reg = <0x4c>;
+	};
+
+	/* U27 temperature sensor placed near RTC battery */
+	temp2: nct75@4d {
+		compatible = "lm75";
+		reg = <0x4d>;
+	};
+
+	/* 2Kb eeprom */
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+	};
+};
+
+&ahci0 {
+	status = "okay";
+};
+
+&ahci1 {
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-0 = <&cf_gtr_fan_pwm>;
+	pinctrl-names = "default";
+
+	wifi-disable {
+		gpio-hog;
+		gpios = <30 GPIO_ACTIVE_LOW>, <31 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "wifi-disable";
+	};
+};
+
+&gpio1 {
+	pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins>;
+	pinctrl-names = "default";
+
+	lte-disable {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "lte-disable";
+	};
+
+	sar-isolation {
+		gpio-hog;
+		gpios = <15 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "sar-isolation";
+	};
+
+	poe-reset {
+		gpio-hog;
+		gpios = <16 GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "poe-reset";
+	};
+};