[2/4] irqchip/meson-gpio: rework meson irqchip driver to support meson-A1 SoCs
diff mbox series

Message ID 20191206121714.14579-3-qianggui.song@amlogic.com
State Superseded
Headers show
Series
  • irqchip/meson-gpio: Add support for Meson-A1 SoC
Related show

Commit Message

Qianggui Song Dec. 6, 2019, 12:17 p.m. UTC
Since Meson-A1 Socs register layout of gpio interrupt controller have
difference with previous chips, registers to decide irq line and offset
of trigger method are all changed, the current driver should be modified.

Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
---
 drivers/irqchip/irq-meson-gpio.c | 79 ++++++++++++++++++++++++--------
 1 file changed, 60 insertions(+), 19 deletions(-)

Comments

Marc Zyngier Dec. 6, 2019, 1:13 p.m. UTC | #1
On 2019-12-06 12:17, Qianggui Song wrote:
> Since Meson-A1 Socs register layout of gpio interrupt controller have
> difference with previous chips, registers to decide irq line and 
> offset
> of trigger method are all changed, the current driver should be 
> modified.
>
> Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
> ---
>  drivers/irqchip/irq-meson-gpio.c | 79 
> ++++++++++++++++++++++++--------
>  1 file changed, 60 insertions(+), 19 deletions(-)
>
> diff --git a/drivers/irqchip/irq-meson-gpio.c
> b/drivers/irqchip/irq-meson-gpio.c
> index 829084b568fa..1824ffc30de2 100644
> --- a/drivers/irqchip/irq-meson-gpio.c
> +++ b/drivers/irqchip/irq-meson-gpio.c
> @@ -30,44 +30,74 @@
>   * stuck at 0. Bits 8 to 15 are responsive and have the expected
>   * effect.
>   */
> -#define REG_EDGE_POL_EDGE(x)	BIT(x)
> -#define REG_EDGE_POL_LOW(x)	BIT(16 + (x))
> -#define REG_BOTH_EDGE(x)	BIT(8 + (x))
> -#define REG_EDGE_POL_MASK(x)    (	\
> -		REG_EDGE_POL_EDGE(x) |	\
> -		REG_EDGE_POL_LOW(x)  |	\
> -		REG_BOTH_EDGE(x))
> +#define REG_EDGE_POL_EDGE(params, 
> x)	BIT((params)->edge_single_offset + (x))
> +#define REG_EDGE_POL_LOW(params, x)	BIT((params)->pol_low_offset + 
> (x))
> +#define REG_BOTH_EDGE(params, x)	BIT((params)->edge_both_offset + 
> (x))
> +#define REG_EDGE_POL_MASK(params, x)    (	\
> +		REG_EDGE_POL_EDGE(params, x) |	\
> +		REG_EDGE_POL_LOW(params, x)  |	\
> +		REG_BOTH_EDGE(params, x))
>  #define REG_PIN_SEL_SHIFT(x)	(((x) % 4) * 8)
>  #define REG_FILTER_SEL_SHIFT(x)	((x) * 4)
>
> +#define INIT_MESON8_COMMON_DATA					\
> +	.edge_single_offset = 0,				\
> +	.pol_low_offset = 16,					\
> +	.pin_sel_mask = 0xff,					\
> +	.ops = {						\
> +		.gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,	\
> +	},

Please place the #defines that operate on the various data structures
*after* the definition of the structures. It would greatly help
reading the changes.

> +
> +struct meson_gpio_irq_controller;
> +static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller 
> *ctl,
> +				    unsigned int channel, unsigned long hwirq);
> +struct irq_ctl_ops {
> +	void (*gpio_irq_sel_pin)(struct meson_gpio_irq_controller *ctl,
> +					 unsigned int channel,
> +					 unsigned long hwirq);
> +	void (*gpio_irq_init)(struct meson_gpio_irq_controller *ctl);
> +};
> +
>  struct meson_gpio_irq_params {
>  	unsigned int nr_hwirq;
>  	bool support_edge_both;
> +	unsigned int edge_both_offset;
> +	unsigned int edge_single_offset;
> +	unsigned int pol_low_offset;
> +	unsigned int pin_sel_mask;
> +	struct irq_ctl_ops ops;
>  };
>
>  static const struct meson_gpio_irq_params meson8_params = {
>  	.nr_hwirq = 134,
> +	INIT_MESON8_COMMON_DATA
>  };
>
>  static const struct meson_gpio_irq_params meson8b_params = {
>  	.nr_hwirq = 119,
> +	INIT_MESON8_COMMON_DATA
>  };
>
>  static const struct meson_gpio_irq_params gxbb_params = {
>  	.nr_hwirq = 133,
> +	INIT_MESON8_COMMON_DATA
>  };
>
>  static const struct meson_gpio_irq_params gxl_params = {
>  	.nr_hwirq = 110,
> +	INIT_MESON8_COMMON_DATA
>  };
>
>  static const struct meson_gpio_irq_params axg_params = {
>  	.nr_hwirq = 100,
> +	INIT_MESON8_COMMON_DATA
>  };
>
>  static const struct meson_gpio_irq_params sm1_params = {
>  	.nr_hwirq = 100,
>  	.support_edge_both = true,
> +	.edge_both_offset = 8,
> +	INIT_MESON8_COMMON_DATA
>  };

OK, this isn't great. The least you could do is to make
your initializer parametric, so that it takes the nr_hwirq as
a parameter.

Then, any additional member that overrides common behaviour
should come after the main initializer.

Also, do you need 'support_edge_both'? Isn't a non-zero
'edge_both_offset' enough to detect the feature?

>
>  static const struct of_device_id meson_irq_gpio_matches[] = {
> @@ -100,9 +130,18 @@ static void meson_gpio_irq_update_bits(struct
> meson_gpio_irq_controller *ctl,
>  	writel_relaxed(tmp, ctl->base + reg);
>  }
>
> -static unsigned int meson_gpio_irq_channel_to_reg(unsigned int 
> channel)
> +static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller 
> *ctl,
> +				    unsigned int channel, unsigned long hwirq)
>  {
> -	return (channel < 4) ? REG_PIN_03_SEL : REG_PIN_47_SEL;
> +	unsigned int reg_offset;
> +	unsigned int bit_offset;
> +
> +	reg_offset = (channel < 4) ? REG_PIN_03_SEL : REG_PIN_47_SEL;
> +	bit_offset = REG_PIN_SEL_SHIFT(channel);
> +
> +	meson_gpio_irq_update_bits(ctl, reg_offset,
> +				   ctl->params->pin_sel_mask << bit_offset,
> +				   hwirq << bit_offset);
>  }
>
>  static int
> @@ -110,7 +149,7 @@ meson_gpio_irq_request_channel(struct
> meson_gpio_irq_controller *ctl,
>  			       unsigned long  hwirq,
>  			       u32 **channel_hwirq)
>  {
> -	unsigned int reg, idx;
> +	unsigned int idx;
>
>  	spin_lock(&ctl->lock);
>
> @@ -129,10 +168,7 @@ meson_gpio_irq_request_channel(struct
> meson_gpio_irq_controller *ctl,
>  	 * Setup the mux of the channel to route the signal of the pad
>  	 * to the appropriate input of the GIC
>  	 */
> -	reg = meson_gpio_irq_channel_to_reg(idx);
> -	meson_gpio_irq_update_bits(ctl, reg,
> -				   0xff << REG_PIN_SEL_SHIFT(idx),
> -				   hwirq << REG_PIN_SEL_SHIFT(idx));
> +	ctl->params->ops.gpio_irq_sel_pin(ctl, idx, hwirq);
>
>  	/*
>  	 * Get the hwirq number assigned to this channel through
> @@ -173,7 +209,9 @@ static int meson_gpio_irq_type_setup(struct
> meson_gpio_irq_controller *ctl,
>  {
>  	u32 val = 0;
>  	unsigned int idx;
> +	const struct meson_gpio_irq_params *params;
>
> +	params = ctl->params;
>  	idx = meson_gpio_irq_get_channel_idx(ctl, channel_hwirq);
>
>  	/*
> @@ -190,22 +228,22 @@ static int meson_gpio_irq_type_setup(struct
> meson_gpio_irq_controller *ctl,
>  	 * precedence over the other edge/polarity settings
>  	 */
>  	if (type == IRQ_TYPE_EDGE_BOTH) {
> -		if (!ctl->params->support_edge_both)
> +		if (!params->support_edge_both)
>  			return -EINVAL;
>
> -		val |= REG_BOTH_EDGE(idx);
> +		val |= REG_BOTH_EDGE(params, idx);
>  	} else {
>  		if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING))
> -			val |= REG_EDGE_POL_EDGE(idx);
> +			val |= REG_EDGE_POL_EDGE(params, idx);
>
>  		if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_EDGE_FALLING))
> -			val |= REG_EDGE_POL_LOW(idx);
> +			val |= REG_EDGE_POL_LOW(params, idx);
>  	}
>
>  	spin_lock(&ctl->lock);
>
>  	meson_gpio_irq_update_bits(ctl, REG_EDGE_POL,
> -				   REG_EDGE_POL_MASK(idx), val);
> +				   REG_EDGE_POL_MASK(params, idx), val);
>
>  	spin_unlock(&ctl->lock);
>
> @@ -371,6 +409,9 @@ static int __init meson_gpio_irq_parse_dt(struct
> device_node *node,
>  		return ret;
>  	}
>
> +	if (ctl->params->ops.gpio_irq_init)
> +		ctl->params->ops.gpio_irq_init(ctl);

It would make sense to provide a dummy init() method, since
you have all the infrastructure already.

> +
>  	return 0;
>  }

Thanks,

         M.
Qianggui Song Dec. 10, 2019, 2:08 a.m. UTC | #2
Hi, Marc
     Thank you for your review

On 2019/12/6 21:13, Marc Zyngier wrote:
> On 2019-12-06 12:17, Qianggui Song wrote:
>> Since Meson-A1 Socs register layout of gpio interrupt controller have
>> difference with previous chips, registers to decide irq line and 
>> offset
>> of trigger method are all changed, the current driver should be 
>> modified.
>>
>> Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
>> ---
>>  drivers/irqchip/irq-meson-gpio.c | 79 
>> ++++++++++++++++++++++++--------
>>  1 file changed, 60 insertions(+), 19 deletions(-)
>>
>> diff --git a/drivers/irqchip/irq-meson-gpio.c
>> b/drivers/irqchip/irq-meson-gpio.c
>> index 829084b568fa..1824ffc30de2 100644
>> --- a/drivers/irqchip/irq-meson-gpio.c
>> +++ b/drivers/irqchip/irq-meson-gpio.c
>> @@ -30,44 +30,74 @@
>>   * stuck at 0. Bits 8 to 15 are responsive and have the expected
>>   * effect.
>>   */
>> -#define REG_EDGE_POL_EDGE(x)	BIT(x)
>> -#define REG_EDGE_POL_LOW(x)	BIT(16 + (x))
>> -#define REG_BOTH_EDGE(x)	BIT(8 + (x))
>> -#define REG_EDGE_POL_MASK(x)    (	\
>> -		REG_EDGE_POL_EDGE(x) |	\
>> -		REG_EDGE_POL_LOW(x)  |	\
>> -		REG_BOTH_EDGE(x))
>> +#define REG_EDGE_POL_EDGE(params, 
>> x)	BIT((params)->edge_single_offset + (x))
>> +#define REG_EDGE_POL_LOW(params, x)	BIT((params)->pol_low_offset + 
>> (x))
>> +#define REG_BOTH_EDGE(params, x)	BIT((params)->edge_both_offset + 
>> (x))
>> +#define REG_EDGE_POL_MASK(params, x)    (	\
>> +		REG_EDGE_POL_EDGE(params, x) |	\
>> +		REG_EDGE_POL_LOW(params, x)  |	\
>> +		REG_BOTH_EDGE(params, x))
>>  #define REG_PIN_SEL_SHIFT(x)	(((x) % 4) * 8)
>>  #define REG_FILTER_SEL_SHIFT(x)	((x) * 4)
>>
>> +#define INIT_MESON8_COMMON_DATA					\
>> +	.edge_single_offset = 0,				\
>> +	.pol_low_offset = 16,					\
>> +	.pin_sel_mask = 0xff,					\
>> +	.ops = {						\
>> +		.gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,	\
>> +	},
> 
> Please place the #defines that operate on the various data structures
> *after* the definition of the structures. It would greatly help
> reading the changes.
> 
OK, will place it below the definition of struct meson_gpio_irq_params
in the next patch.
>> +
>> +struct meson_gpio_irq_controller;
>> +static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller 
>> *ctl,
>> +				    unsigned int channel, unsigned long hwirq);
>> +struct irq_ctl_ops {
>> +	void (*gpio_irq_sel_pin)(struct meson_gpio_irq_controller *ctl,
>> +					 unsigned int channel,
>> +					 unsigned long hwirq);
>> +	void (*gpio_irq_init)(struct meson_gpio_irq_controller *ctl);
>> +};
>> +
>>  struct meson_gpio_irq_params {
>>  	unsigned int nr_hwirq;
>>  	bool support_edge_both;
>> +	unsigned int edge_both_offset;
>> +	unsigned int edge_single_offset;
>> +	unsigned int pol_low_offset;
>> +	unsigned int pin_sel_mask;
>> +	struct irq_ctl_ops ops;
>>  };
>>
>>  static const struct meson_gpio_irq_params meson8_params = {
>>  	.nr_hwirq = 134,
>> +	INIT_MESON8_COMMON_DATA
>>  };
>>
>>  static const struct meson_gpio_irq_params meson8b_params = {
>>  	.nr_hwirq = 119,
>> +	INIT_MESON8_COMMON_DATA
>>  };
>>
>>  static const struct meson_gpio_irq_params gxbb_params = {
>>  	.nr_hwirq = 133,
>> +	INIT_MESON8_COMMON_DATA
>>  };
>>
>>  static const struct meson_gpio_irq_params gxl_params = {
>>  	.nr_hwirq = 110,
>> +	INIT_MESON8_COMMON_DATA
>>  };
>>
>>  static const struct meson_gpio_irq_params axg_params = {
>>  	.nr_hwirq = 100,
>> +	INIT_MESON8_COMMON_DATA
>>  };
>>
>>  static const struct meson_gpio_irq_params sm1_params = {
>>  	.nr_hwirq = 100,
>>  	.support_edge_both = true,
>> +	.edge_both_offset = 8,
>> +	INIT_MESON8_COMMON_DATA
>>  };
> 
> OK, this isn't great. The least you could do is to make
> your initializer parametric, so that it takes the nr_hwirq as
> a parameter.
> 
> Then, any additional member that overrides common behaviour
> should come after the main initializer.
> 
> Also, do you need 'support_edge_both'? Isn't a non-zero
> 'edge_both_offset' enough to detect the feature?
> 

Sorry, but I am not very clear that "make your initializer parametric,
so that it takes the nr_hwirq as a parameter". Is that
initializer(initial function in .ops ? ) as a parameter of struct
meson_gpio_irq_params ? If nr_hwirq as a parameter of init function of
.ops then will make lot of init function for each platform.

How about move .ops from  macro like below:
#define INIT_MESON8_COMMON_DATA					\
	.edge_single_offset = 0,				\
	.pol_low_offset = 16,					\
	.pin_sel_mask = 0xff,

static const struct meson_gpio_irq_params sm1_params = {
 	.nr_hwirq = 100,//main initializer
	.ops = {
              .gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,
               /*in below to assign support_edge_both
                * edge_both_offset
                * call after main initializer to additional
                * member
                */
              .gpio_irq_init = meson_sm1_irq_init,
	},
  	INIT_MESON8_COMMON_DATA// m8 to sm1 are the same.
};

About support_edge_both
support_edge_both & edge_both_offset are used for sm1 or later chip, but
the value are different with A1 which this patch set support.For SM1 is
8, but A1 is 16, so I am not one hundred percent sure that later chip
design will change to edge_both_offet to zero to set both edge trigger.
Let' s see edge_single_offset, it is set to 0 in A1 from 16 which is
previous chip use.I think support_edge_bot should be kept.

>>
>>  static const struct of_device_id meson_irq_gpio_matches[] = {
>> @@ -100,9 +130,18 @@ static void meson_gpio_irq_update_bits(struct
>> meson_gpio_irq_controller *ctl,
>>  	writel_relaxed(tmp, ctl->base + reg);
>>  }
>>
>> -static unsigned int meson_gpio_irq_channel_to_reg(unsigned int 
>> channel)
>> +static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller 
>> *ctl,
>> +				    unsigned int channel, unsigned long hwirq)
>>  {
>> -	return (channel < 4) ? REG_PIN_03_SEL : REG_PIN_47_SEL;
>> +	unsigned int reg_offset;
>> +	unsigned int bit_offset;
>> +
>> +	reg_offset = (channel < 4) ? REG_PIN_03_SEL : REG_PIN_47_SEL;
>> +	bit_offset = REG_PIN_SEL_SHIFT(channel);
>> +
>> +	meson_gpio_irq_update_bits(ctl, reg_offset,
>> +				   ctl->params->pin_sel_mask << bit_offset,
>> +				   hwirq << bit_offset);
>>  }
>>
>>  static int
>> @@ -110,7 +149,7 @@ meson_gpio_irq_request_channel(struct
>> meson_gpio_irq_controller *ctl,
>>  			       unsigned long  hwirq,
>>  			       u32 **channel_hwirq)
>>  {
>> -	unsigned int reg, idx;
>> +	unsigned int idx;
>>
>>  	spin_lock(&ctl->lock);
>>
>> @@ -129,10 +168,7 @@ meson_gpio_irq_request_channel(struct
>> meson_gpio_irq_controller *ctl,
>>  	 * Setup the mux of the channel to route the signal of the pad
>>  	 * to the appropriate input of the GIC
>>  	 */
>> -	reg = meson_gpio_irq_channel_to_reg(idx);
>> -	meson_gpio_irq_update_bits(ctl, reg,
>> -				   0xff << REG_PIN_SEL_SHIFT(idx),
>> -				   hwirq << REG_PIN_SEL_SHIFT(idx));
>> +	ctl->params->ops.gpio_irq_sel_pin(ctl, idx, hwirq);
>>
>>  	/*
>>  	 * Get the hwirq number assigned to this channel through
>> @@ -173,7 +209,9 @@ static int meson_gpio_irq_type_setup(struct
>> meson_gpio_irq_controller *ctl,
>>  {
>>  	u32 val = 0;
>>  	unsigned int idx;
>> +	const struct meson_gpio_irq_params *params;
>>
>> +	params = ctl->params;
>>  	idx = meson_gpio_irq_get_channel_idx(ctl, channel_hwirq);
>>
>>  	/*
>> @@ -190,22 +228,22 @@ static int meson_gpio_irq_type_setup(struct
>> meson_gpio_irq_controller *ctl,
>>  	 * precedence over the other edge/polarity settings
>>  	 */
>>  	if (type == IRQ_TYPE_EDGE_BOTH) {
>> -		if (!ctl->params->support_edge_both)
>> +		if (!params->support_edge_both)
>>  			return -EINVAL;
>>
>> -		val |= REG_BOTH_EDGE(idx);
>> +		val |= REG_BOTH_EDGE(params, idx);
>>  	} else {
>>  		if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING))
>> -			val |= REG_EDGE_POL_EDGE(idx);
>> +			val |= REG_EDGE_POL_EDGE(params, idx);
>>
>>  		if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_EDGE_FALLING))
>> -			val |= REG_EDGE_POL_LOW(idx);
>> +			val |= REG_EDGE_POL_LOW(params, idx);
>>  	}
>>
>>  	spin_lock(&ctl->lock);
>>
>>  	meson_gpio_irq_update_bits(ctl, REG_EDGE_POL,
>> -				   REG_EDGE_POL_MASK(idx), val);
>> +				   REG_EDGE_POL_MASK(params, idx), val);
>>
>>  	spin_unlock(&ctl->lock);
>>
>> @@ -371,6 +409,9 @@ static int __init meson_gpio_irq_parse_dt(struct
>> device_node *node,
>>  		return ret;
>>  	}
>>
>> +	if (ctl->params->ops.gpio_irq_init)
>> +		ctl->params->ops.gpio_irq_init(ctl);
> 
> It would make sense to provide a dummy init() method, since
> you have all the infrastructure already.
> 
Okay
>> +
>>  	return 0;
>>  }
> 
> Thanks,
> 
>          M.
>
Marc Zyngier Dec. 11, 2019, 5:26 p.m. UTC | #3
On 2019-12-10 02:08, Qianggui Song wrote:
> Hi, Marc
>      Thank you for your review
>
> On 2019/12/6 21:13, Marc Zyngier wrote:
>> On 2019-12-06 12:17, Qianggui Song wrote:
>>> Since Meson-A1 Socs register layout of gpio interrupt controller 
>>> have
>>> difference with previous chips, registers to decide irq line and
>>> offset
>>> of trigger method are all changed, the current driver should be
>>> modified.
>>>
>>> Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
>>> ---
>>>  drivers/irqchip/irq-meson-gpio.c | 79
>>> ++++++++++++++++++++++++--------
>>>  1 file changed, 60 insertions(+), 19 deletions(-)
>>>
>>> diff --git a/drivers/irqchip/irq-meson-gpio.c
>>> b/drivers/irqchip/irq-meson-gpio.c
>>> index 829084b568fa..1824ffc30de2 100644
>>> --- a/drivers/irqchip/irq-meson-gpio.c
>>> +++ b/drivers/irqchip/irq-meson-gpio.c
>>> @@ -30,44 +30,74 @@
>>>   * stuck at 0. Bits 8 to 15 are responsive and have the expected
>>>   * effect.
>>>   */
>>> -#define REG_EDGE_POL_EDGE(x)	BIT(x)
>>> -#define REG_EDGE_POL_LOW(x)	BIT(16 + (x))
>>> -#define REG_BOTH_EDGE(x)	BIT(8 + (x))
>>> -#define REG_EDGE_POL_MASK(x)    (	\
>>> -		REG_EDGE_POL_EDGE(x) |	\
>>> -		REG_EDGE_POL_LOW(x)  |	\
>>> -		REG_BOTH_EDGE(x))
>>> +#define REG_EDGE_POL_EDGE(params,
>>> x)	BIT((params)->edge_single_offset + (x))
>>> +#define REG_EDGE_POL_LOW(params, x)	BIT((params)->pol_low_offset +
>>> (x))
>>> +#define REG_BOTH_EDGE(params, x)	BIT((params)->edge_both_offset +
>>> (x))
>>> +#define REG_EDGE_POL_MASK(params, x)    (	\
>>> +		REG_EDGE_POL_EDGE(params, x) |	\
>>> +		REG_EDGE_POL_LOW(params, x)  |	\
>>> +		REG_BOTH_EDGE(params, x))
>>>  #define REG_PIN_SEL_SHIFT(x)	(((x) % 4) * 8)
>>>  #define REG_FILTER_SEL_SHIFT(x)	((x) * 4)
>>>
>>> +#define INIT_MESON8_COMMON_DATA					\
>>> +	.edge_single_offset = 0,				\
>>> +	.pol_low_offset = 16,					\
>>> +	.pin_sel_mask = 0xff,					\
>>> +	.ops = {						\
>>> +		.gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,	\
>>> +	},
>>
>> Please place the #defines that operate on the various data 
>> structures
>> *after* the definition of the structures. It would greatly help
>> reading the changes.
>>
> OK, will place it below the definition of struct 
> meson_gpio_irq_params
> in the next patch.
>>> +
>>> +struct meson_gpio_irq_controller;
>>> +static void meson8_gpio_irq_sel_pin(struct 
>>> meson_gpio_irq_controller
>>> *ctl,
>>> +				    unsigned int channel, unsigned long hwirq);
>>> +struct irq_ctl_ops {
>>> +	void (*gpio_irq_sel_pin)(struct meson_gpio_irq_controller *ctl,
>>> +					 unsigned int channel,
>>> +					 unsigned long hwirq);
>>> +	void (*gpio_irq_init)(struct meson_gpio_irq_controller *ctl);
>>> +};
>>> +
>>>  struct meson_gpio_irq_params {
>>>  	unsigned int nr_hwirq;
>>>  	bool support_edge_both;
>>> +	unsigned int edge_both_offset;
>>> +	unsigned int edge_single_offset;
>>> +	unsigned int pol_low_offset;
>>> +	unsigned int pin_sel_mask;
>>> +	struct irq_ctl_ops ops;
>>>  };
>>>
>>>  static const struct meson_gpio_irq_params meson8_params = {
>>>  	.nr_hwirq = 134,
>>> +	INIT_MESON8_COMMON_DATA
>>>  };
>>>
>>>  static const struct meson_gpio_irq_params meson8b_params = {
>>>  	.nr_hwirq = 119,
>>> +	INIT_MESON8_COMMON_DATA
>>>  };
>>>
>>>  static const struct meson_gpio_irq_params gxbb_params = {
>>>  	.nr_hwirq = 133,
>>> +	INIT_MESON8_COMMON_DATA
>>>  };
>>>
>>>  static const struct meson_gpio_irq_params gxl_params = {
>>>  	.nr_hwirq = 110,
>>> +	INIT_MESON8_COMMON_DATA
>>>  };
>>>
>>>  static const struct meson_gpio_irq_params axg_params = {
>>>  	.nr_hwirq = 100,
>>> +	INIT_MESON8_COMMON_DATA
>>>  };
>>>
>>>  static const struct meson_gpio_irq_params sm1_params = {
>>>  	.nr_hwirq = 100,
>>>  	.support_edge_both = true,
>>> +	.edge_both_offset = 8,
>>> +	INIT_MESON8_COMMON_DATA
>>>  };
>>
>> OK, this isn't great. The least you could do is to make
>> your initializer parametric, so that it takes the nr_hwirq as
>> a parameter.
>>
>> Then, any additional member that overrides common behaviour
>> should come after the main initializer.
>>
>> Also, do you need 'support_edge_both'? Isn't a non-zero
>> 'edge_both_offset' enough to detect the feature?
>>
>
> Sorry, but I am not very clear that "make your initializer 
> parametric,
> so that it takes the nr_hwirq as a parameter". Is that
> initializer(initial function in .ops ? ) as a parameter of struct
> meson_gpio_irq_params ? If nr_hwirq as a parameter of init function 
> of
> .ops then will make lot of init function for each platform.
>
> How about move .ops from  macro like below:
> #define INIT_MESON8_COMMON_DATA					\
> 	.edge_single_offset = 0,				\
> 	.pol_low_offset = 16,					\
> 	.pin_sel_mask = 0xff,
>
> static const struct meson_gpio_irq_params sm1_params = {
>  	.nr_hwirq = 100,//main initializer
> 	.ops = {
>               .gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,
>                /*in below to assign support_edge_both
>                 * edge_both_offset
>                 * call after main initializer to additional
>                 * member
>                 */
>               .gpio_irq_init = meson_sm1_irq_init,
> 	},
>   	INIT_MESON8_COMMON_DATA// m8 to sm1 are the same.
> };

No, what I'm suggesting is something like this:

diff --git a/drivers/irqchip/irq-meson-gpio.c 
b/drivers/irqchip/irq-meson-gpio.c
index 8478100706a6..27a3207a944d 100644
--- a/drivers/irqchip/irq-meson-gpio.c
+++ b/drivers/irqchip/irq-meson-gpio.c
@@ -43,24 +43,27 @@
  /* Below is used for Meson-A1 series like chips*/
  #define REG_PIN_A1_SEL	0x04

-#define INIT_MESON8_COMMON_DATA					\
-	.edge_single_offset = 0,				\
-	.pol_low_offset = 16,					\
-	.pin_sel_mask = 0xff,					\
-	.ops = {						\
-		.gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,	\
-	},
-
-#define INIT_MESON_A1_COMMON_DATA				\
-	.support_edge_both = true,				\
-	.edge_both_offset = 16,					\
-	.edge_single_offset = 8,				\
-	.pol_low_offset = 0,					\
-	.pin_sel_mask = 0x7f,					\
-	.ops = {						\
-		.gpio_irq_sel_pin = meson_a1_gpio_irq_sel_pin,	\
-		.gpio_irq_init = meson_a1_gpio_irq_init,	\
-	},
+#define INIT_MESON_COMMON(irqs, init, sel)		\
+	.nr_hwirq = irqs,				\
+	.ops = {					\
+		.gpio_irq_sel_pin = sel,		\
+		.gpio_irq_init = init,			\
+	}
+
+#define INIT_MESON8_COMMON_DATA(irqs)			\
+	INIT_MESON_COMMON(irqs, NULL,			\
+			  meson8_gpio_irq_sel_pin),	\
+	.pol_low_offset = 16,				\
+	.pin_sel_mask = 0xff,
+
+#define INIT_MESON_A1_COMMON_DATA(irqs)			\
+	INIT_MESON_COMMON(irqs, meson_a1_gpio_irq_init,	\
+			  meson_a1_gpio_irq_sel_pin),	\
+	.support_edge_both = true,			\
+	.edge_both_offset = 16,				\
+	.edge_single_offset = 8,			\
+	.pol_low_offset = 0,				\
+	.pin_sel_mask = 0x7f,

  struct meson_gpio_irq_controller;
  static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller 
*ctl,
@@ -89,40 +92,33 @@ struct meson_gpio_irq_params {
  };

  static const struct meson_gpio_irq_params meson8_params = {
-	.nr_hwirq = 134,
-	INIT_MESON8_COMMON_DATA
+	INIT_MESON8_COMMON_DATA(134),
  };

  static const struct meson_gpio_irq_params meson8b_params = {
-	.nr_hwirq = 119,
-	INIT_MESON8_COMMON_DATA
+	INIT_MESON8_COMMON_DATA(119),
  };

  static const struct meson_gpio_irq_params gxbb_params = {
-	.nr_hwirq = 133,
-	INIT_MESON8_COMMON_DATA
+	INIT_MESON8_COMMON_DATA(133),
  };

  static const struct meson_gpio_irq_params gxl_params = {
-	.nr_hwirq = 110,
-	INIT_MESON8_COMMON_DATA
+	INIT_MESON8_COMMON_DATA(110),
  };

  static const struct meson_gpio_irq_params axg_params = {
-	.nr_hwirq = 100,
-	INIT_MESON8_COMMON_DATA
+	INIT_MESON8_COMMON_DATA(100),
  };

  static const struct meson_gpio_irq_params sm1_params = {
-	.nr_hwirq = 100,
+	INIT_MESON8_COMMON_DATA(100),
  	.support_edge_both = true,
  	.edge_both_offset = 8,
-	INIT_MESON8_COMMON_DATA
  };

  static const struct meson_gpio_irq_params a1_params = {
-	.nr_hwirq = 62,
-	INIT_MESON_A1_COMMON_DATA
+	INIT_MESON_A1_COMMON_DATA(62),
  };

  static const struct of_device_id meson_irq_gpio_matches[] = {


Thanks,

         M.
Qianggui Song Dec. 12, 2019, 11:13 a.m. UTC | #4
On 2019/12/12 1:26, Marc Zyngier wrote:
> On 2019-12-10 02:08, Qianggui Song wrote:
>> Hi, Marc
>>      Thank you for your review
>>
>> On 2019/12/6 21:13, Marc Zyngier wrote:
>>> On 2019-12-06 12:17, Qianggui Song wrote:
>>>> Since Meson-A1 Socs register layout of gpio interrupt controller 
>>>> have
>>>> difference with previous chips, registers to decide irq line and
>>>> offset
>>>> of trigger method are all changed, the current driver should be
>>>> modified.
>>>>
>>>> Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
>>>> ---
>>>>  drivers/irqchip/irq-meson-gpio.c | 79
>>>> ++++++++++++++++++++++++--------
>>>>  1 file changed, 60 insertions(+), 19 deletions(-)
>>>>
>>>> diff --git a/drivers/irqchip/irq-meson-gpio.c
>>>> b/drivers/irqchip/irq-meson-gpio.c
>>>> index 829084b568fa..1824ffc30de2 100644
>>>> --- a/drivers/irqchip/irq-meson-gpio.c
>>>> +++ b/drivers/irqchip/irq-meson-gpio.c
>>>> @@ -30,44 +30,74 @@
>>>>   * stuck at 0. Bits 8 to 15 are responsive and have the expected
>>>>   * effect.
>>>>   */
>>>> -#define REG_EDGE_POL_EDGE(x)	BIT(x)
>>>> -#define REG_EDGE_POL_LOW(x)	BIT(16 + (x))
>>>> -#define REG_BOTH_EDGE(x)	BIT(8 + (x))
>>>> -#define REG_EDGE_POL_MASK(x)    (	\
>>>> -		REG_EDGE_POL_EDGE(x) |	\
>>>> -		REG_EDGE_POL_LOW(x)  |	\
>>>> -		REG_BOTH_EDGE(x))
>>>> +#define REG_EDGE_POL_EDGE(params,
>>>> x)	BIT((params)->edge_single_offset + (x))
>>>> +#define REG_EDGE_POL_LOW(params, x)	BIT((params)->pol_low_offset +
>>>> (x))
>>>> +#define REG_BOTH_EDGE(params, x)	BIT((params)->edge_both_offset +
>>>> (x))
>>>> +#define REG_EDGE_POL_MASK(params, x)    (	\
>>>> +		REG_EDGE_POL_EDGE(params, x) |	\
>>>> +		REG_EDGE_POL_LOW(params, x)  |	\
>>>> +		REG_BOTH_EDGE(params, x))
>>>>  #define REG_PIN_SEL_SHIFT(x)	(((x) % 4) * 8)
>>>>  #define REG_FILTER_SEL_SHIFT(x)	((x) * 4)
>>>>
>>>> +#define INIT_MESON8_COMMON_DATA					\
>>>> +	.edge_single_offset = 0,				\
>>>> +	.pol_low_offset = 16,					\
>>>> +	.pin_sel_mask = 0xff,					\
>>>> +	.ops = {						\
>>>> +		.gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,	\
>>>> +	},
>>>
>>> Please place the #defines that operate on the various data 
>>> structures
>>> *after* the definition of the structures. It would greatly help
>>> reading the changes.
>>>
>> OK, will place it below the definition of struct 
>> meson_gpio_irq_params
>> in the next patch.
>>>> +
>>>> +struct meson_gpio_irq_controller;
>>>> +static void meson8_gpio_irq_sel_pin(struct 
>>>> meson_gpio_irq_controller
>>>> *ctl,
>>>> +				    unsigned int channel, unsigned long hwirq);
>>>> +struct irq_ctl_ops {
>>>> +	void (*gpio_irq_sel_pin)(struct meson_gpio_irq_controller *ctl,
>>>> +					 unsigned int channel,
>>>> +					 unsigned long hwirq);
>>>> +	void (*gpio_irq_init)(struct meson_gpio_irq_controller *ctl);
>>>> +};
>>>> +
>>>>  struct meson_gpio_irq_params {
>>>>  	unsigned int nr_hwirq;
>>>>  	bool support_edge_both;
>>>> +	unsigned int edge_both_offset;
>>>> +	unsigned int edge_single_offset;
>>>> +	unsigned int pol_low_offset;
>>>> +	unsigned int pin_sel_mask;
>>>> +	struct irq_ctl_ops ops;
>>>>  };
>>>>
>>>>  static const struct meson_gpio_irq_params meson8_params = {
>>>>  	.nr_hwirq = 134,
>>>> +	INIT_MESON8_COMMON_DATA
>>>>  };
>>>>
>>>>  static const struct meson_gpio_irq_params meson8b_params = {
>>>>  	.nr_hwirq = 119,
>>>> +	INIT_MESON8_COMMON_DATA
>>>>  };
>>>>
>>>>  static const struct meson_gpio_irq_params gxbb_params = {
>>>>  	.nr_hwirq = 133,
>>>> +	INIT_MESON8_COMMON_DATA
>>>>  };
>>>>
>>>>  static const struct meson_gpio_irq_params gxl_params = {
>>>>  	.nr_hwirq = 110,
>>>> +	INIT_MESON8_COMMON_DATA
>>>>  };
>>>>
>>>>  static const struct meson_gpio_irq_params axg_params = {
>>>>  	.nr_hwirq = 100,
>>>> +	INIT_MESON8_COMMON_DATA
>>>>  };
>>>>
>>>>  static const struct meson_gpio_irq_params sm1_params = {
>>>>  	.nr_hwirq = 100,
>>>>  	.support_edge_both = true,
>>>> +	.edge_both_offset = 8,
>>>> +	INIT_MESON8_COMMON_DATA
>>>>  };
>>>
>>> OK, this isn't great. The least you could do is to make
>>> your initializer parametric, so that it takes the nr_hwirq as
>>> a parameter.
>>>
>>> Then, any additional member that overrides common behaviour
>>> should come after the main initializer.
>>>
>>> Also, do you need 'support_edge_both'? Isn't a non-zero
>>> 'edge_both_offset' enough to detect the feature?
>>>
>>
>> Sorry, but I am not very clear that "make your initializer 
>> parametric,
>> so that it takes the nr_hwirq as a parameter". Is that
>> initializer(initial function in .ops ? ) as a parameter of struct
>> meson_gpio_irq_params ? If nr_hwirq as a parameter of init function 
>> of
>> .ops then will make lot of init function for each platform.
>>
>> How about move .ops from  macro like below:
>> #define INIT_MESON8_COMMON_DATA					\
>> 	.edge_single_offset = 0,				\
>> 	.pol_low_offset = 16,					\
>> 	.pin_sel_mask = 0xff,
>>
>> static const struct meson_gpio_irq_params sm1_params = {
>>  	.nr_hwirq = 100,//main initializer
>> 	.ops = {
>>               .gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,
>>                /*in below to assign support_edge_both
>>                 * edge_both_offset
>>                 * call after main initializer to additional
>>                 * member
>>                 */
>>               .gpio_irq_init = meson_sm1_irq_init,
>> 	},
>>   	INIT_MESON8_COMMON_DATA// m8 to sm1 are the same.
>> };
> 
> No, what I'm suggesting is something like this:
> 
> diff --git a/drivers/irqchip/irq-meson-gpio.c 
> b/drivers/irqchip/irq-meson-gpio.c
> index 8478100706a6..27a3207a944d 100644
> --- a/drivers/irqchip/irq-meson-gpio.c
> +++ b/drivers/irqchip/irq-meson-gpio.c
> @@ -43,24 +43,27 @@
>   /* Below is used for Meson-A1 series like chips*/
>   #define REG_PIN_A1_SEL	0x04
> 
> -#define INIT_MESON8_COMMON_DATA					\
> -	.edge_single_offset = 0,				\
> -	.pol_low_offset = 16,					\
> -	.pin_sel_mask = 0xff,					\
> -	.ops = {						\
> -		.gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,	\
> -	},
> -
> -#define INIT_MESON_A1_COMMON_DATA				\
> -	.support_edge_both = true,				\
> -	.edge_both_offset = 16,					\
> -	.edge_single_offset = 8,				\
> -	.pol_low_offset = 0,					\
> -	.pin_sel_mask = 0x7f,					\
> -	.ops = {						\
> -		.gpio_irq_sel_pin = meson_a1_gpio_irq_sel_pin,	\
> -		.gpio_irq_init = meson_a1_gpio_irq_init,	\
> -	},
> +#define INIT_MESON_COMMON(irqs, init, sel)		\
> +	.nr_hwirq = irqs,				\
> +	.ops = {					\
> +		.gpio_irq_sel_pin = sel,		\
> +		.gpio_irq_init = init,			\
> +	}
> +
> +#define INIT_MESON8_COMMON_DATA(irqs)			\
> +	INIT_MESON_COMMON(irqs, NULL,			\
> +			  meson8_gpio_irq_sel_pin),	\
> +	.pol_low_offset = 16,				\
> +	.pin_sel_mask = 0xff,
> +
> +#define INIT_MESON_A1_COMMON_DATA(irqs)			\
> +	INIT_MESON_COMMON(irqs, meson_a1_gpio_irq_init,	\
> +			  meson_a1_gpio_irq_sel_pin),	\
> +	.support_edge_both = true,			\
> +	.edge_both_offset = 16,				\
> +	.edge_single_offset = 8,			\
> +	.pol_low_offset = 0,				\
> +	.pin_sel_mask = 0x7f,
> 
>   struct meson_gpio_irq_controller;
>   static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller 
> *ctl,
> @@ -89,40 +92,33 @@ struct meson_gpio_irq_params {
>   };
> 
>   static const struct meson_gpio_irq_params meson8_params = {
> -	.nr_hwirq = 134,
> -	INIT_MESON8_COMMON_DATA
> +	INIT_MESON8_COMMON_DATA(134),
>   };
> 
>   static const struct meson_gpio_irq_params meson8b_params = {
> -	.nr_hwirq = 119,
> -	INIT_MESON8_COMMON_DATA
> +	INIT_MESON8_COMMON_DATA(119),
>   };
> 
>   static const struct meson_gpio_irq_params gxbb_params = {
> -	.nr_hwirq = 133,
> -	INIT_MESON8_COMMON_DATA
> +	INIT_MESON8_COMMON_DATA(133),
>   };
> 
>   static const struct meson_gpio_irq_params gxl_params = {
> -	.nr_hwirq = 110,
> -	INIT_MESON8_COMMON_DATA
> +	INIT_MESON8_COMMON_DATA(110),
>   };
> 
>   static const struct meson_gpio_irq_params axg_params = {
> -	.nr_hwirq = 100,
> -	INIT_MESON8_COMMON_DATA
> +	INIT_MESON8_COMMON_DATA(100),
>   };
> 
>   static const struct meson_gpio_irq_params sm1_params = {
> -	.nr_hwirq = 100,
> +	INIT_MESON8_COMMON_DATA(100),
>   	.support_edge_both = true,
>   	.edge_both_offset = 8,
> -	INIT_MESON8_COMMON_DATA
>   };
> 
>   static const struct meson_gpio_irq_params a1_params = {
> -	.nr_hwirq = 62,
> -	INIT_MESON_A1_COMMON_DATA
> +	INIT_MESON_A1_COMMON_DATA(62),
>   };
> 
Thanks, will try it in later patch
>   static const struct of_device_id meson_irq_gpio_matches[] = {
> 
> 
> Thanks,
> 
>          M.
>

Patch
diff mbox series

diff --git a/drivers/irqchip/irq-meson-gpio.c b/drivers/irqchip/irq-meson-gpio.c
index 829084b568fa..1824ffc30de2 100644
--- a/drivers/irqchip/irq-meson-gpio.c
+++ b/drivers/irqchip/irq-meson-gpio.c
@@ -30,44 +30,74 @@ 
  * stuck at 0. Bits 8 to 15 are responsive and have the expected
  * effect.
  */
-#define REG_EDGE_POL_EDGE(x)	BIT(x)
-#define REG_EDGE_POL_LOW(x)	BIT(16 + (x))
-#define REG_BOTH_EDGE(x)	BIT(8 + (x))
-#define REG_EDGE_POL_MASK(x)    (	\
-		REG_EDGE_POL_EDGE(x) |	\
-		REG_EDGE_POL_LOW(x)  |	\
-		REG_BOTH_EDGE(x))
+#define REG_EDGE_POL_EDGE(params, x)	BIT((params)->edge_single_offset + (x))
+#define REG_EDGE_POL_LOW(params, x)	BIT((params)->pol_low_offset + (x))
+#define REG_BOTH_EDGE(params, x)	BIT((params)->edge_both_offset + (x))
+#define REG_EDGE_POL_MASK(params, x)    (	\
+		REG_EDGE_POL_EDGE(params, x) |	\
+		REG_EDGE_POL_LOW(params, x)  |	\
+		REG_BOTH_EDGE(params, x))
 #define REG_PIN_SEL_SHIFT(x)	(((x) % 4) * 8)
 #define REG_FILTER_SEL_SHIFT(x)	((x) * 4)
 
+#define INIT_MESON8_COMMON_DATA					\
+	.edge_single_offset = 0,				\
+	.pol_low_offset = 16,					\
+	.pin_sel_mask = 0xff,					\
+	.ops = {						\
+		.gpio_irq_sel_pin = meson8_gpio_irq_sel_pin,	\
+	},
+
+struct meson_gpio_irq_controller;
+static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller *ctl,
+				    unsigned int channel, unsigned long hwirq);
+struct irq_ctl_ops {
+	void (*gpio_irq_sel_pin)(struct meson_gpio_irq_controller *ctl,
+					 unsigned int channel,
+					 unsigned long hwirq);
+	void (*gpio_irq_init)(struct meson_gpio_irq_controller *ctl);
+};
+
 struct meson_gpio_irq_params {
 	unsigned int nr_hwirq;
 	bool support_edge_both;
+	unsigned int edge_both_offset;
+	unsigned int edge_single_offset;
+	unsigned int pol_low_offset;
+	unsigned int pin_sel_mask;
+	struct irq_ctl_ops ops;
 };
 
 static const struct meson_gpio_irq_params meson8_params = {
 	.nr_hwirq = 134,
+	INIT_MESON8_COMMON_DATA
 };
 
 static const struct meson_gpio_irq_params meson8b_params = {
 	.nr_hwirq = 119,
+	INIT_MESON8_COMMON_DATA
 };
 
 static const struct meson_gpio_irq_params gxbb_params = {
 	.nr_hwirq = 133,
+	INIT_MESON8_COMMON_DATA
 };
 
 static const struct meson_gpio_irq_params gxl_params = {
 	.nr_hwirq = 110,
+	INIT_MESON8_COMMON_DATA
 };
 
 static const struct meson_gpio_irq_params axg_params = {
 	.nr_hwirq = 100,
+	INIT_MESON8_COMMON_DATA
 };
 
 static const struct meson_gpio_irq_params sm1_params = {
 	.nr_hwirq = 100,
 	.support_edge_both = true,
+	.edge_both_offset = 8,
+	INIT_MESON8_COMMON_DATA
 };
 
 static const struct of_device_id meson_irq_gpio_matches[] = {
@@ -100,9 +130,18 @@  static void meson_gpio_irq_update_bits(struct meson_gpio_irq_controller *ctl,
 	writel_relaxed(tmp, ctl->base + reg);
 }
 
-static unsigned int meson_gpio_irq_channel_to_reg(unsigned int channel)
+static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller *ctl,
+				    unsigned int channel, unsigned long hwirq)
 {
-	return (channel < 4) ? REG_PIN_03_SEL : REG_PIN_47_SEL;
+	unsigned int reg_offset;
+	unsigned int bit_offset;
+
+	reg_offset = (channel < 4) ? REG_PIN_03_SEL : REG_PIN_47_SEL;
+	bit_offset = REG_PIN_SEL_SHIFT(channel);
+
+	meson_gpio_irq_update_bits(ctl, reg_offset,
+				   ctl->params->pin_sel_mask << bit_offset,
+				   hwirq << bit_offset);
 }
 
 static int
@@ -110,7 +149,7 @@  meson_gpio_irq_request_channel(struct meson_gpio_irq_controller *ctl,
 			       unsigned long  hwirq,
 			       u32 **channel_hwirq)
 {
-	unsigned int reg, idx;
+	unsigned int idx;
 
 	spin_lock(&ctl->lock);
 
@@ -129,10 +168,7 @@  meson_gpio_irq_request_channel(struct meson_gpio_irq_controller *ctl,
 	 * Setup the mux of the channel to route the signal of the pad
 	 * to the appropriate input of the GIC
 	 */
-	reg = meson_gpio_irq_channel_to_reg(idx);
-	meson_gpio_irq_update_bits(ctl, reg,
-				   0xff << REG_PIN_SEL_SHIFT(idx),
-				   hwirq << REG_PIN_SEL_SHIFT(idx));
+	ctl->params->ops.gpio_irq_sel_pin(ctl, idx, hwirq);
 
 	/*
 	 * Get the hwirq number assigned to this channel through
@@ -173,7 +209,9 @@  static int meson_gpio_irq_type_setup(struct meson_gpio_irq_controller *ctl,
 {
 	u32 val = 0;
 	unsigned int idx;
+	const struct meson_gpio_irq_params *params;
 
+	params = ctl->params;
 	idx = meson_gpio_irq_get_channel_idx(ctl, channel_hwirq);
 
 	/*
@@ -190,22 +228,22 @@  static int meson_gpio_irq_type_setup(struct meson_gpio_irq_controller *ctl,
 	 * precedence over the other edge/polarity settings
 	 */
 	if (type == IRQ_TYPE_EDGE_BOTH) {
-		if (!ctl->params->support_edge_both)
+		if (!params->support_edge_both)
 			return -EINVAL;
 
-		val |= REG_BOTH_EDGE(idx);
+		val |= REG_BOTH_EDGE(params, idx);
 	} else {
 		if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING))
-			val |= REG_EDGE_POL_EDGE(idx);
+			val |= REG_EDGE_POL_EDGE(params, idx);
 
 		if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_EDGE_FALLING))
-			val |= REG_EDGE_POL_LOW(idx);
+			val |= REG_EDGE_POL_LOW(params, idx);
 	}
 
 	spin_lock(&ctl->lock);
 
 	meson_gpio_irq_update_bits(ctl, REG_EDGE_POL,
-				   REG_EDGE_POL_MASK(idx), val);
+				   REG_EDGE_POL_MASK(params, idx), val);
 
 	spin_unlock(&ctl->lock);
 
@@ -371,6 +409,9 @@  static int __init meson_gpio_irq_parse_dt(struct device_node *node,
 		return ret;
 	}
 
+	if (ctl->params->ops.gpio_irq_init)
+		ctl->params->ops.gpio_irq_init(ctl);
+
 	return 0;
 }