| Message ID | 20191211124459.20508-2-kieran.bingham+renesas@ideasonboard.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | MAX9286 GMSL Support | expand |
On Wed, Dec 11, 2019 at 12:44:58PM +0000, Kieran Bingham wrote: > From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> > > The MAX9286 deserializes video data received on up to 4 Gigabit > Multimedia Serial Links (GMSL) and outputs them on a CSI-2 port using up > to 4 data lanes. > > Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> > Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> > --- > .../bindings/media/i2c/maxim,max9286.yaml | 289 ++++++++++++++++++ > 1 file changed, 289 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml A couple of nits, with those fixed: Reviewed-by: Rob Herring <robh@kernel.org> > > diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml > new file mode 100644 > index 000000000000..d37ea2c432f6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml > @@ -0,0 +1,289 @@ > +# SPDX-License-Identifier: GPL-2.0-only Dual license new bindings please: (GPL-2.0-only OR BSD-2-Clause) > +# Copyright (C) 2019 Renesas Electronics Corp. > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/i2c/maxim,max9286.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Maxim Integrated Quad GMSL Deserializer > + > +maintainers: > + - Jacopo Mondi <jacopo+renesas@jmondi.org> > + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> > + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> > + - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> > + > +description: -| I usually see '|-', but I guess that works. > + The MAX9286 deserializer receives video data on up to 4 Gigabit Multimedia > + Serial Links (GMSL) and outputs them on a CSI-2 D-PHY port using up to 4 data > + lanes. > + > + In addition to video data, the GMSL links carry a bidirectional control > + channel that encapsulates I2C messages. The MAX9286 forwards all I2C traffic > + not addressed to itself to the other side of the links, where a GMSL > + serializer will output it on a local I2C bus. In the other direction all I2C > + traffic received over GMSL by the MAX9286 is output on the local I2C bus. > + > +properties: > + '#address-cells': > + const: 1 > + > + '#size-cells': > + const: 0 > + > + compatible: > + const: maxim,max9286 > + > + reg: > + description: I2C device address > + maxItems: 1 > + > + poc-supply: > + description: Regulator providing Power over Coax to the cameras > + maxItems: 1 > + > + enable-gpios: > + description: GPIO connected to the \#PWDN pin with inverted polarity > + maxItems: 1 > + > + ports: > + type: object > + description: -| > + The connections to the MAX9286 GMSL and its endpoint nodes are modelled > + using the OF graph bindings in accordance with the video interface > + bindings defined in > + Documentation/devicetree/bindings/media/video-interfaces.txt. > + > + The following table lists the port number corresponding to each device > + port. > + > + Port Description > + ---------------------------------------- > + Port 0 GMSL Input 0 > + Port 1 GMSL Input 1 > + Port 2 GMSL Input 2 > + Port 3 GMSL Input 3 > + Port 4 CSI-2 Output > + > + properties: > + '#address-cells': > + const: 1 > + > + '#size-cells': > + const: 0 > + > + port@[0-3]: > + type: object > + properties: > + reg: > + enum: [ 0, 1, 2, 3 ] > + > + endpoint: > + type: object > + > + properties: > + remote-endpoint: > + description: -| > + phandle to the remote GMSL source endpoint subnode in the > + remote node port. > + maxItems: 1 This is not an array. You can just drop and assume it has a type defined elsewhere. > + > + required: > + - remote-endpoint > + > + required: > + - reg > + - endpoint > + > + additionalProperties: false > + > + port@4: > + type: object > + properties: > + reg: > + const: 4 > + > + endpoint: > + type: object > + > + properties: > + remote-endpoint: > + description: phandle to the remote CSI-2 sink endpoint. > + maxItems: 1 And here. > + > + data-lanes: > + description: array of physical CSI-2 data lane indexes. > + > + required: > + - remote-endpoint > + - data-lanes > + > + required: > + - reg > + - endpoint > + > + additionalProperties: false > + > + required: > + - port@4 > + > + i2c-mux: > + type: object > + description: -| > + Each GMSL link is modelled as a child bus of an i2c bus > + multiplexer/switch, in accordance with bindings described in > + Documentation/devicetree/bindings/i2c/i2c-mux.txt. The serializer > + device on the remote end of the GMSL link shall be modelled as a child > + node of the corresponding I2C bus. > + > + properties: > + '#address-cells': > + const: 1 > + > + '#size-cells': > + const: 0 > + > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - ports > + - i2c-mux > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + > + i2c@e66d8000 { > + #address-cells = <1>; > + #size-cells = <0>; > + > + reg = <0 0xe66d8000 0 0x40>; > + > + gmsl-deserializer@2c { > + compatible = "maxim,max9286"; > + reg = <0x2c>; > + poc-supply = <&camera_poc_12v>; > + enable-gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + max9286_in0: endpoint { > + remote-endpoint = <&rdacm20_out0>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + max9286_in1: endpoint { > + remote-endpoint = <&rdacm20_out1>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + max9286_in2: endpoint { > + remote-endpoint = <&rdacm20_out2>; > + }; > + }; > + > + port@3 { > + reg = <3>; > + > + max9286_in3: endpoint { > + remote-endpoint = <&rdacm20_out3>; > + }; > + }; > + > + port@4 { > + reg = <4>; > + > + max9286_out: endpoint { > + data-lanes = <1 2 3 4>; > + remote-endpoint = <&csi40_in>; > + }; > + }; > + }; > + > + i2c-mux { > + #address-cells = <1>; > + #size-cells = <0>; > + > + i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + > + reg = <0>; > + > + camera@51 { > + reg = <0x51>; > + > + port { > + rdacm20_out0: endpoint { > + remote-endpoint = <&max9286_in0>; > + }; > + }; > + > + }; > + }; > + > + i2c@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <1>; > + > + camera@52 { > + reg = <0x52>; > + > + port { > + rdacm20_out1: endpoint { > + remote-endpoint = <&max9286_in1>; > + }; > + }; > + }; > + }; > + > + i2c@2 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <2>; > + > + camera@53 { > + reg = <0x53>; > + > + port { > + rdacm20_out2: endpoint { > + remote-endpoint = <&max9286_in2>; > + }; > + }; > + }; > + }; > + > + i2c@3 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <3>; > + > + camera@54 { > + reg = <0x54>; > + > + port { > + rdacm20_out3: endpoint { > + remote-endpoint = <&max9286_in3>; > + }; > + }; > + }; > + }; > + }; > + }; > + }; > -- > 2.20.1 >
Thanks Rob, On 18/12/2019 18:13, Rob Herring wrote: > On Wed, Dec 11, 2019 at 12:44:58PM +0000, Kieran Bingham wrote: >> From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> >> >> The MAX9286 deserializes video data received on up to 4 Gigabit >> Multimedia Serial Links (GMSL) and outputs them on a CSI-2 port using up >> to 4 data lanes. >> >> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> >> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> >> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> >> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> >> --- >> .../bindings/media/i2c/maxim,max9286.yaml | 289 ++++++++++++++++++ >> 1 file changed, 289 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml > > A couple of nits, with those fixed: I'll fix them up :-D Thank you very much. Converting this to YAML picked up a few issues in our DTS - so it certainly seems very worthwhile! -- Kieran > Reviewed-by: Rob Herring <robh@kernel.org> > >> >> diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml >> new file mode 100644 >> index 000000000000..d37ea2c432f6 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml >> @@ -0,0 +1,289 @@ >> +# SPDX-License-Identifier: GPL-2.0-only > > Dual license new bindings please: > > (GPL-2.0-only OR BSD-2-Clause) That's two of those I've got to fix up for you :D. I'll make sure all new ones I add have this correctly presented. >> +# Copyright (C) 2019 Renesas Electronics Corp. >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/media/i2c/maxim,max9286.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Maxim Integrated Quad GMSL Deserializer >> + >> +maintainers: >> + - Jacopo Mondi <jacopo+renesas@jmondi.org> >> + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> >> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> >> + - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> >> + >> +description: -| > > I usually see '|-', but I guess that works. Oh, I'm happy to change to conform to whatever is the accepted norm... > >> + The MAX9286 deserializer receives video data on up to 4 Gigabit Multimedia >> + Serial Links (GMSL) and outputs them on a CSI-2 D-PHY port using up to 4 data >> + lanes. >> + >> + In addition to video data, the GMSL links carry a bidirectional control >> + channel that encapsulates I2C messages. The MAX9286 forwards all I2C traffic >> + not addressed to itself to the other side of the links, where a GMSL >> + serializer will output it on a local I2C bus. In the other direction all I2C >> + traffic received over GMSL by the MAX9286 is output on the local I2C bus. >> + >> +properties: >> + '#address-cells': >> + const: 1 >> + >> + '#size-cells': >> + const: 0 >> + >> + compatible: >> + const: maxim,max9286 >> + >> + reg: >> + description: I2C device address >> + maxItems: 1 >> + >> + poc-supply: >> + description: Regulator providing Power over Coax to the cameras >> + maxItems: 1 >> + >> + enable-gpios: >> + description: GPIO connected to the \#PWDN pin with inverted polarity >> + maxItems: 1 >> + >> + ports: >> + type: object >> + description: -| >> + The connections to the MAX9286 GMSL and its endpoint nodes are modelled >> + using the OF graph bindings in accordance with the video interface >> + bindings defined in >> + Documentation/devicetree/bindings/media/video-interfaces.txt. >> + >> + The following table lists the port number corresponding to each device >> + port. >> + >> + Port Description >> + ---------------------------------------- >> + Port 0 GMSL Input 0 >> + Port 1 GMSL Input 1 >> + Port 2 GMSL Input 2 >> + Port 3 GMSL Input 3 >> + Port 4 CSI-2 Output >> + >> + properties: >> + '#address-cells': >> + const: 1 >> + >> + '#size-cells': >> + const: 0 >> + >> + port@[0-3]: >> + type: object >> + properties: >> + reg: >> + enum: [ 0, 1, 2, 3 ] >> + >> + endpoint: >> + type: object >> + >> + properties: >> + remote-endpoint: >> + description: -| >> + phandle to the remote GMSL source endpoint subnode in the >> + remote node port. >> + maxItems: 1 > > This is not an array. You can just drop and assume it has a type defined > elsewhere. > Will fix and validate. >> + >> + required: >> + - remote-endpoint >> + >> + required: >> + - reg >> + - endpoint >> + >> + additionalProperties: false >> + >> + port@4: >> + type: object >> + properties: >> + reg: >> + const: 4 >> + >> + endpoint: >> + type: object >> + >> + properties: >> + remote-endpoint: >> + description: phandle to the remote CSI-2 sink endpoint. >> + maxItems: 1 > > And here. Likewise. > >> + >> + data-lanes: >> + description: array of physical CSI-2 data lane indexes. >> + >> + required: >> + - remote-endpoint >> + - data-lanes >> + >> + required: >> + - reg >> + - endpoint >> + >> + additionalProperties: false >> + >> + required: >> + - port@4 >> + >> + i2c-mux: >> + type: object >> + description: -| >> + Each GMSL link is modelled as a child bus of an i2c bus >> + multiplexer/switch, in accordance with bindings described in >> + Documentation/devicetree/bindings/i2c/i2c-mux.txt. The serializer >> + device on the remote end of the GMSL link shall be modelled as a child >> + node of the corresponding I2C bus. >> + >> + properties: >> + '#address-cells': >> + const: 1 >> + >> + '#size-cells': >> + const: 0 >> + >> + additionalProperties: false >> + >> +required: >> + - compatible >> + - reg >> + - ports >> + - i2c-mux >> + >> +additionalProperties: false >> + >> +examples: >> + - | >> + #include <dt-bindings/gpio/gpio.h> >> + >> + i2c@e66d8000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + reg = <0 0xe66d8000 0 0x40>; >> + >> + gmsl-deserializer@2c { >> + compatible = "maxim,max9286"; >> + reg = <0x2c>; >> + poc-supply = <&camera_poc_12v>; >> + enable-gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + max9286_in0: endpoint { >> + remote-endpoint = <&rdacm20_out0>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + max9286_in1: endpoint { >> + remote-endpoint = <&rdacm20_out1>; >> + }; >> + }; >> + >> + port@2 { >> + reg = <2>; >> + >> + max9286_in2: endpoint { >> + remote-endpoint = <&rdacm20_out2>; >> + }; >> + }; >> + >> + port@3 { >> + reg = <3>; >> + >> + max9286_in3: endpoint { >> + remote-endpoint = <&rdacm20_out3>; >> + }; >> + }; >> + >> + port@4 { >> + reg = <4>; >> + >> + max9286_out: endpoint { >> + data-lanes = <1 2 3 4>; >> + remote-endpoint = <&csi40_in>; >> + }; >> + }; >> + }; >> + >> + i2c-mux { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + i2c@0 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + reg = <0>; >> + >> + camera@51 { >> + reg = <0x51>; >> + >> + port { >> + rdacm20_out0: endpoint { >> + remote-endpoint = <&max9286_in0>; >> + }; >> + }; >> + >> + }; >> + }; >> + >> + i2c@1 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <1>; >> + >> + camera@52 { >> + reg = <0x52>; >> + >> + port { >> + rdacm20_out1: endpoint { >> + remote-endpoint = <&max9286_in1>; >> + }; >> + }; >> + }; >> + }; >> + >> + i2c@2 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <2>; >> + >> + camera@53 { >> + reg = <0x53>; >> + >> + port { >> + rdacm20_out2: endpoint { >> + remote-endpoint = <&max9286_in2>; >> + }; >> + }; >> + }; >> + }; >> + >> + i2c@3 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <3>; >> + >> + camera@54 { >> + reg = <0x54>; >> + >> + port { >> + rdacm20_out3: endpoint { >> + remote-endpoint = <&max9286_in3>; >> + }; >> + }; >> + }; >> + }; >> + }; >> + }; >> + }; >> -- >> 2.20.1 >>
diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml new file mode 100644 index 000000000000..d37ea2c432f6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml @@ -0,0 +1,289 @@ +# SPDX-License-Identifier: GPL-2.0-only +# Copyright (C) 2019 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/maxim,max9286.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated Quad GMSL Deserializer + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> + +description: -| + The MAX9286 deserializer receives video data on up to 4 Gigabit Multimedia + Serial Links (GMSL) and outputs them on a CSI-2 D-PHY port using up to 4 data + lanes. + + In addition to video data, the GMSL links carry a bidirectional control + channel that encapsulates I2C messages. The MAX9286 forwards all I2C traffic + not addressed to itself to the other side of the links, where a GMSL + serializer will output it on a local I2C bus. In the other direction all I2C + traffic received over GMSL by the MAX9286 is output on the local I2C bus. + +properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + compatible: + const: maxim,max9286 + + reg: + description: I2C device address + maxItems: 1 + + poc-supply: + description: Regulator providing Power over Coax to the cameras + maxItems: 1 + + enable-gpios: + description: GPIO connected to the \#PWDN pin with inverted polarity + maxItems: 1 + + ports: + type: object + description: -| + The connections to the MAX9286 GMSL and its endpoint nodes are modelled + using the OF graph bindings in accordance with the video interface + bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + + The following table lists the port number corresponding to each device + port. + + Port Description + ---------------------------------------- + Port 0 GMSL Input 0 + Port 1 GMSL Input 1 + Port 2 GMSL Input 2 + Port 3 GMSL Input 3 + Port 4 CSI-2 Output + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + port@[0-3]: + type: object + properties: + reg: + enum: [ 0, 1, 2, 3 ] + + endpoint: + type: object + + properties: + remote-endpoint: + description: -| + phandle to the remote GMSL source endpoint subnode in the + remote node port. + maxItems: 1 + + required: + - remote-endpoint + + required: + - reg + - endpoint + + additionalProperties: false + + port@4: + type: object + properties: + reg: + const: 4 + + endpoint: + type: object + + properties: + remote-endpoint: + description: phandle to the remote CSI-2 sink endpoint. + maxItems: 1 + + data-lanes: + description: array of physical CSI-2 data lane indexes. + + required: + - remote-endpoint + - data-lanes + + required: + - reg + - endpoint + + additionalProperties: false + + required: + - port@4 + + i2c-mux: + type: object + description: -| + Each GMSL link is modelled as a child bus of an i2c bus + multiplexer/switch, in accordance with bindings described in + Documentation/devicetree/bindings/i2c/i2c-mux.txt. The serializer + device on the remote end of the GMSL link shall be modelled as a child + node of the corresponding I2C bus. + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + additionalProperties: false + +required: + - compatible + - reg + - ports + - i2c-mux + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c@e66d8000 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0 0xe66d8000 0 0x40>; + + gmsl-deserializer@2c { + compatible = "maxim,max9286"; + reg = <0x2c>; + poc-supply = <&camera_poc_12v>; + enable-gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + max9286_in0: endpoint { + remote-endpoint = <&rdacm20_out0>; + }; + }; + + port@1 { + reg = <1>; + + max9286_in1: endpoint { + remote-endpoint = <&rdacm20_out1>; + }; + }; + + port@2 { + reg = <2>; + + max9286_in2: endpoint { + remote-endpoint = <&rdacm20_out2>; + }; + }; + + port@3 { + reg = <3>; + + max9286_in3: endpoint { + remote-endpoint = <&rdacm20_out3>; + }; + }; + + port@4 { + reg = <4>; + + max9286_out: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + + camera@51 { + reg = <0x51>; + + port { + rdacm20_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + camera@52 { + reg = <0x52>; + + port { + rdacm20_out1: endpoint { + remote-endpoint = <&max9286_in1>; + }; + }; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + camera@53 { + reg = <0x53>; + + port { + rdacm20_out2: endpoint { + remote-endpoint = <&max9286_in2>; + }; + }; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + camera@54 { + reg = <0x54>; + + port { + rdacm20_out3: endpoint { + remote-endpoint = <&max9286_in3>; + }; + }; + }; + }; + }; + }; + };