| Message ID | 1576496415-23064-1-git-send-email-tamizhr@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/2] dt-bindings: ath10k: Add new dt entries to identify coex support | expand |
On Mon, Dec 16, 2019 at 05:10:14PM +0530, Tamizh Chelvam wrote: > This adds new dt entries qcom,coexist-support and qcom,coexist-gpio-pin > which will be used by ath10k driver to identify coex support > of a hardware and notify wifi firmware the gpio pin number. > This pin number information is needed for the hardware QCA4019. > > Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org> > --- > Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 6 ++++++ > 1 file changed, 6 insertions(+) > > diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt > index 0171283..a41e936 100644 > --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt > +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt > @@ -87,6 +87,10 @@ Optional properties: > Definition: Quirk specifying that the firmware expects the 8bit version > of the host capability QMI request > - qcom,xo-cal-data: xo cal offset to be configured in xo trim register. > +- qcom,coexist-support : should contain eithr "0" or "1" to indicate coex > + support by the hardware. > +- qcom,coexist-gpio-pin : gpio pin number information to support coex > + which will be used by wifi firmware. What combinations of these 2 properties are valid? Is qcom,coexist-gpio-pin required for coexist support? If so then it alone should be enough to enable/disable coexist. > > Example (to supply PCI based wifi block details): > > @@ -156,6 +160,8 @@ wifi0: wifi@a000000 { > qcom,msi_addr = <0x0b006040>; > qcom,msi_base = <0x40>; > qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; > + qcom,coexist-support = <1>; > + qcom,coexist-gpio-pin = <0x33>; > }; > > Example (to supply wcn3990 SoC wifi block details): > -- > 1.9.1
Hi Rob, Thanks for your review comments. >> This adds new dt entries qcom,coexist-support and >> qcom,coexist-gpio-pin >> which will be used by ath10k driver to identify coex support >> of a hardware and notify wifi firmware the gpio pin number. >> This pin number information is needed for the hardware QCA4019. >> >> Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org> >> --- >> Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 6 >> ++++++ >> 1 file changed, 6 insertions(+) >> >> diff --git >> a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt >> b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt >> index 0171283..a41e936 100644 >> --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt >> +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt >> @@ -87,6 +87,10 @@ Optional properties: >> Definition: Quirk specifying that the firmware expects the 8bit >> version >> of the host capability QMI request >> - qcom,xo-cal-data: xo cal offset to be configured in xo trim >> register. >> +- qcom,coexist-support : should contain eithr "0" or "1" to indicate >> coex >> + support by the hardware. >> +- qcom,coexist-gpio-pin : gpio pin number information to support >> coex >> + which will be used by wifi firmware. > > What combinations of these 2 properties are valid? > > Is qcom,coexist-gpio-pin required for coexist support? If so then it > alone should be enough to enable/disable coexist. > qcom,coexist-gpio-pin is required for QCA4019 devices. And other ath10k devices doesn't required that value. So only added two fields to enable/disable coexist and another for notifying the gpio pin info. >> >> Example (to supply PCI based wifi block details): >> >> @@ -156,6 +160,8 @@ wifi0: wifi@a000000 { >> qcom,msi_addr = <0x0b006040>; >> qcom,msi_base = <0x40>; >> qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; >> + qcom,coexist-support = <1>; >> + qcom,coexist-gpio-pin = <0x33>; >> }; >> >> Example (to supply wcn3990 SoC wifi block details): >> -- Thanks, Tamizh.
On Sun, Dec 29, 2019 at 10:07 PM <tamizhr@codeaurora.org> wrote: > > Hi Rob, > > Thanks for your review comments. > > >> This adds new dt entries qcom,coexist-support and > >> qcom,coexist-gpio-pin > >> which will be used by ath10k driver to identify coex support > >> of a hardware and notify wifi firmware the gpio pin number. > >> This pin number information is needed for the hardware QCA4019. > >> > >> Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org> > >> --- > >> Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 6 > >> ++++++ > >> 1 file changed, 6 insertions(+) > >> > >> diff --git > >> a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt > >> b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt > >> index 0171283..a41e936 100644 > >> --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt > >> +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt > >> @@ -87,6 +87,10 @@ Optional properties: > >> Definition: Quirk specifying that the firmware expects the 8bit > >> version > >> of the host capability QMI request > >> - qcom,xo-cal-data: xo cal offset to be configured in xo trim > >> register. > >> +- qcom,coexist-support : should contain eithr "0" or "1" to indicate typo > >> coex > >> + support by the hardware. > >> +- qcom,coexist-gpio-pin : gpio pin number information to support > >> coex > >> + which will be used by wifi firmware. > > > > What combinations of these 2 properties are valid? > > > > Is qcom,coexist-gpio-pin required for coexist support? If so then it > > alone should be enough to enable/disable coexist. > > > qcom,coexist-gpio-pin is required for QCA4019 devices. And other ath10k > devices doesn't required that value. > So only added two fields to enable/disable coexist and another for > notifying the gpio pin info. Okay. 'qcom,coexist-support' can be boolean instead. Unless you need it to override a default setting. Rob
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 0171283..a41e936 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -87,6 +87,10 @@ Optional properties: Definition: Quirk specifying that the firmware expects the 8bit version of the host capability QMI request - qcom,xo-cal-data: xo cal offset to be configured in xo trim register. +- qcom,coexist-support : should contain eithr "0" or "1" to indicate coex + support by the hardware. +- qcom,coexist-gpio-pin : gpio pin number information to support coex + which will be used by wifi firmware. Example (to supply PCI based wifi block details): @@ -156,6 +160,8 @@ wifi0: wifi@a000000 { qcom,msi_addr = <0x0b006040>; qcom,msi_base = <0x40>; qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; + qcom,coexist-support = <1>; + qcom,coexist-gpio-pin = <0x33>; }; Example (to supply wcn3990 SoC wifi block details):
This adds new dt entries qcom,coexist-support and qcom,coexist-gpio-pin which will be used by ath10k driver to identify coex support of a hardware and notify wifi firmware the gpio pin number. This pin number information is needed for the hardware QCA4019. Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org> --- Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 6 ++++++ 1 file changed, 6 insertions(+)