[v6,5/7] phy: amlogic: Add Amlogic AXG MIPI/PCIE analog PHY Driver
diff mbox series

Message ID 20200123232943.10229-6-repk@triplefau.lt
State New
Headers show
Series
  • PCI: amlogic: Make PCIe working reliably on AXG platforms
Related show

Commit Message

Remi Pommarel Jan. 23, 2020, 11:29 p.m. UTC
This adds support for the MIPI analog PHY which is also used for PCIE
found in the Amlogic AXG SoC Family.

MIPI or PCIE selection is done by the #phy-cells, making the mode
static and exclusive.

For now only PCIE fonctionality is supported.

This PHY will be used to replace the mipi_enable clock gating logic
which was mistakenly added in the clock subsystem. This also activate
a non documented band gap bit in those registers that allows reliable
PCIE clock signal generation on AXG platforms.

Signed-off-by: Remi Pommarel <repk@triplefau.lt>
---
 drivers/phy/amlogic/Kconfig                   |  11 +
 drivers/phy/amlogic/Makefile                  |  11 +-
 .../amlogic/phy-meson-axg-mipi-pcie-analog.c  | 188 ++++++++++++++++++
 3 files changed, 205 insertions(+), 5 deletions(-)
 create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c

Comments

Remi Pommarel Jan. 24, 2020, 8:32 a.m. UTC | #1
Add missing Reviewed/Acked-by from v5.

On Fri, Jan 24, 2020 at 12:29:41AM +0100, Remi Pommarel wrote:
> This adds support for the MIPI analog PHY which is also used for PCIE
> found in the Amlogic AXG SoC Family.
> 
> MIPI or PCIE selection is done by the #phy-cells, making the mode
> static and exclusive.
> 
> For now only PCIE fonctionality is supported.
> 
> This PHY will be used to replace the mipi_enable clock gating logic
> which was mistakenly added in the clock subsystem. This also activate
> a non documented band gap bit in those registers that allows reliable
> PCIE clock signal generation on AXG platforms.

Acked-by: Jerome Brunet <jbrunet@baylibre.com>

> 
> Signed-off-by: Remi Pommarel <repk@triplefau.lt>
> ---
>  drivers/phy/amlogic/Kconfig                   |  11 +
>  drivers/phy/amlogic/Makefile                  |  11 +-
>  .../amlogic/phy-meson-axg-mipi-pcie-analog.c  | 188 ++++++++++++++++++
>  3 files changed, 205 insertions(+), 5 deletions(-)
>  create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> 
> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> index af774ac2b934..8c9cf2403591 100644
> --- a/drivers/phy/amlogic/Kconfig
> +++ b/drivers/phy/amlogic/Kconfig
> @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
>  	  Enable this to support the Meson USB3 + PCIE Combo PHY found
>  	  in Meson G12A SoCs.
>  	  If unsure, say N.
> +
> +config PHY_MESON_AXG_MIPI_PCIE_ANALOG
> +	tristate "Meson AXG MIPI + PCIE analog PHY driver"
> +	default ARCH_MESON
> +	depends on OF && (ARCH_MESON || COMPILE_TEST)
> +	select GENERIC_PHY
> +	select REGMAP_MMIO
> +	help
> +	  Enable this to support the Meson MIPI + PCIE analog PHY
> +	  found in Meson AXG SoCs.
> +	  If unsure, say N.
> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> index 11d1c42ac2be..0aecf92d796a 100644
> --- a/drivers/phy/amlogic/Makefile
> +++ b/drivers/phy/amlogic/Makefile
> @@ -1,6 +1,7 @@
>  # SPDX-License-Identifier: GPL-2.0-only
> -obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
> -obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
> -obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
> -obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
> -obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
> +obj-$(CONFIG_PHY_MESON8B_USB2)			+= phy-meson8b-usb2.o
> +obj-$(CONFIG_PHY_MESON_GXL_USB2)		+= phy-meson-gxl-usb2.o
> +obj-$(CONFIG_PHY_MESON_G12A_USB2)		+= phy-meson-g12a-usb2.o
> +obj-$(CONFIG_PHY_MESON_GXL_USB3)		+= phy-meson-gxl-usb3.o
> +obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)		+= phy-meson-g12a-usb3-pcie.o
> +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG)	+= phy-meson-axg-mipi-pcie-analog.o
> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> new file mode 100644
> index 000000000000..1431cbf885e1
> --- /dev/null
> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> @@ -0,0 +1,188 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Amlogic AXG MIPI + PCIE analog PHY driver
> + *
> + * Copyright (C) 2019 Remi Pommarel <repk@triplefau.lt>
> + */
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define HHI_MIPI_CNTL0 0x00
> +#define		HHI_MIPI_CNTL0_COMMON_BLOCK	GENMASK(31, 28)
> +#define		HHI_MIPI_CNTL0_ENABLE		BIT(29)
> +#define		HHI_MIPI_CNTL0_BANDGAP		BIT(26)
> +#define		HHI_MIPI_CNTL0_DECODE_TO_RTERM	GENMASK(15, 12)
> +#define		HHI_MIPI_CNTL0_OUTPUT_EN	BIT(3)
> +
> +#define HHI_MIPI_CNTL1 0x01
> +#define		HHI_MIPI_CNTL1_CH0_CML_PDR_EN	BIT(12)
> +#define		HHI_MIPI_CNTL1_LP_ABILITY	GENMASK(5, 4)
> +#define		HHI_MIPI_CNTL1_LP_RESISTER	BIT(3)
> +#define		HHI_MIPI_CNTL1_INPUT_SETTING	BIT(2)
> +#define		HHI_MIPI_CNTL1_INPUT_SEL	BIT(1)
> +#define		HHI_MIPI_CNTL1_PRBS7_EN		BIT(0)
> +
> +#define HHI_MIPI_CNTL2 0x02
> +#define		HHI_MIPI_CNTL2_CH_PU		GENMASK(31, 25)
> +#define		HHI_MIPI_CNTL2_CH_CTL		GENMASK(24, 19)
> +#define		HHI_MIPI_CNTL2_CH0_DIGDR_EN	BIT(18)
> +#define		HHI_MIPI_CNTL2_CH_DIGDR_EN	BIT(17)
> +#define		HHI_MIPI_CNTL2_LPULPS_EN	BIT(16)
> +#define		HHI_MIPI_CNTL2_CH_EN(n)		BIT(15 - (n))
> +#define		HHI_MIPI_CNTL2_CH0_LP_CTL	GENMASK(10, 1)
> +
> +struct phy_axg_mipi_pcie_analog_priv {
> +	struct phy *phy;
> +	unsigned int mode;
> +	struct regmap *regmap;
> +};
> +
> +static const struct regmap_config phy_axg_mipi_pcie_analog_regmap_conf = {
> +	.reg_bits = 8,
> +	.val_bits = 32,
> +	.reg_stride = 4,
> +	.max_register = HHI_MIPI_CNTL2,
> +};
> +
> +static int phy_axg_mipi_pcie_analog_power_on(struct phy *phy)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> +
> +	/* MIPI not supported yet */
> +	if (priv->mode != PHY_TYPE_PCIE)
> +		return -EINVAL;
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_power_off(struct phy *phy)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> +
> +	/* MIPI not supported yet */
> +	if (priv->mode != PHY_TYPE_PCIE)
> +		return -EINVAL;
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_BANDGAP, 0);
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_ENABLE, 0);
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_init(struct phy *phy)
> +{
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_exit(struct phy *phy)
> +{
> +	return 0;
> +}
> +
> +static const struct phy_ops phy_axg_mipi_pcie_analog_ops = {
> +	.init = phy_axg_mipi_pcie_analog_init,
> +	.exit = phy_axg_mipi_pcie_analog_exit,
> +	.power_on = phy_axg_mipi_pcie_analog_power_on,
> +	.power_off = phy_axg_mipi_pcie_analog_power_off,
> +	.owner = THIS_MODULE,
> +};
> +
> +static struct phy *phy_axg_mipi_pcie_analog_xlate(struct device *dev,
> +						  struct of_phandle_args *args)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = dev_get_drvdata(dev);
> +	unsigned int mode;
> +
> +	if (args->args_count != 1) {
> +		dev_err(dev, "invalid number of arguments\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	mode = args->args[0];
> +
> +	/* MIPI mode is not supported yet */
> +	if (mode != PHY_TYPE_PCIE) {
> +		dev_err(dev, "invalid phy mode select argument\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	priv->mode = mode;
> +	return priv->phy;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_probe(struct platform_device *pdev)
> +{
> +	struct phy_provider *phy;
> +	struct device *dev = &pdev->dev;
> +	struct phy_axg_mipi_pcie_analog_priv *priv;
> +	struct device_node *np = dev->of_node;
> +	struct regmap *map;
> +	struct resource *res;
> +	void __iomem *base;
> +	int ret;
> +
> +	priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(base)) {
> +		dev_err(dev, "failed to get regmap base\n");
> +		return PTR_ERR(base);
> +	}
> +
> +	map = devm_regmap_init_mmio(dev, base,
> +				    &phy_axg_mipi_pcie_analog_regmap_conf);
> +	if (IS_ERR(map)) {
> +		dev_err(dev, "failed to get HHI regmap\n");
> +		return PTR_ERR(map);
> +	}
> +	priv->regmap = map;
> +
> +	priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_analog_ops);
> +	if (IS_ERR(priv->phy)) {
> +		ret = PTR_ERR(priv->phy);
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(dev, "failed to create PHY\n");
> +		return ret;
> +	}
> +
> +	phy_set_drvdata(priv->phy, priv);
> +	dev_set_drvdata(dev, priv);
> +
> +	phy = devm_of_phy_provider_register(dev,
> +					    phy_axg_mipi_pcie_analog_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy);
> +}
> +
> +static const struct of_device_id phy_axg_mipi_pcie_analog_of_match[] = {
> +	{
> +		.compatible = "amlogic,axg-mipi-pcie-analog-phy",
> +	},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_analog_of_match);
> +
> +static struct platform_driver phy_axg_mipi_pcie_analog_driver = {
> +	.probe = phy_axg_mipi_pcie_analog_probe,
> +	.driver = {
> +		.name = "phy-axg-mipi-pcie-analog",
> +		.of_match_table = phy_axg_mipi_pcie_analog_of_match,
> +	},
> +};
> +module_platform_driver(phy_axg_mipi_pcie_analog_driver);
> +
> +MODULE_AUTHOR("Remi Pommarel <repk@triplefau.lt>");
> +MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE analog PHY driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.24.1
>
Lorenzo Pieralisi March 3, 2020, 5:19 p.m. UTC | #2
On Fri, Jan 24, 2020 at 12:29:41AM +0100, Remi Pommarel wrote:
> This adds support for the MIPI analog PHY which is also used for PCIE
> found in the Amlogic AXG SoC Family.
> 
> MIPI or PCIE selection is done by the #phy-cells, making the mode
> static and exclusive.
> 
> For now only PCIE fonctionality is supported.
> 
> This PHY will be used to replace the mipi_enable clock gating logic
> which was mistakenly added in the clock subsystem. This also activate
> a non documented band gap bit in those registers that allows reliable
> PCIE clock signal generation on AXG platforms.
> 
> Signed-off-by: Remi Pommarel <repk@triplefau.lt>
> ---
>  drivers/phy/amlogic/Kconfig                   |  11 +
>  drivers/phy/amlogic/Makefile                  |  11 +-
>  .../amlogic/phy-meson-axg-mipi-pcie-analog.c  | 188 ++++++++++++++++++
>  3 files changed, 205 insertions(+), 5 deletions(-)
>  create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c

Kishon, Neil,

can you please review/ack this patch and patch 6 ?

I would like to queue the series shortly, thanks.

Lorenzo

> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> index af774ac2b934..8c9cf2403591 100644
> --- a/drivers/phy/amlogic/Kconfig
> +++ b/drivers/phy/amlogic/Kconfig
> @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
>  	  Enable this to support the Meson USB3 + PCIE Combo PHY found
>  	  in Meson G12A SoCs.
>  	  If unsure, say N.
> +
> +config PHY_MESON_AXG_MIPI_PCIE_ANALOG
> +	tristate "Meson AXG MIPI + PCIE analog PHY driver"
> +	default ARCH_MESON
> +	depends on OF && (ARCH_MESON || COMPILE_TEST)
> +	select GENERIC_PHY
> +	select REGMAP_MMIO
> +	help
> +	  Enable this to support the Meson MIPI + PCIE analog PHY
> +	  found in Meson AXG SoCs.
> +	  If unsure, say N.
> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> index 11d1c42ac2be..0aecf92d796a 100644
> --- a/drivers/phy/amlogic/Makefile
> +++ b/drivers/phy/amlogic/Makefile
> @@ -1,6 +1,7 @@
>  # SPDX-License-Identifier: GPL-2.0-only
> -obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
> -obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
> -obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
> -obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
> -obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
> +obj-$(CONFIG_PHY_MESON8B_USB2)			+= phy-meson8b-usb2.o
> +obj-$(CONFIG_PHY_MESON_GXL_USB2)		+= phy-meson-gxl-usb2.o
> +obj-$(CONFIG_PHY_MESON_G12A_USB2)		+= phy-meson-g12a-usb2.o
> +obj-$(CONFIG_PHY_MESON_GXL_USB3)		+= phy-meson-gxl-usb3.o
> +obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)		+= phy-meson-g12a-usb3-pcie.o
> +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG)	+= phy-meson-axg-mipi-pcie-analog.o
> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> new file mode 100644
> index 000000000000..1431cbf885e1
> --- /dev/null
> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> @@ -0,0 +1,188 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Amlogic AXG MIPI + PCIE analog PHY driver
> + *
> + * Copyright (C) 2019 Remi Pommarel <repk@triplefau.lt>
> + */
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define HHI_MIPI_CNTL0 0x00
> +#define		HHI_MIPI_CNTL0_COMMON_BLOCK	GENMASK(31, 28)
> +#define		HHI_MIPI_CNTL0_ENABLE		BIT(29)
> +#define		HHI_MIPI_CNTL0_BANDGAP		BIT(26)
> +#define		HHI_MIPI_CNTL0_DECODE_TO_RTERM	GENMASK(15, 12)
> +#define		HHI_MIPI_CNTL0_OUTPUT_EN	BIT(3)
> +
> +#define HHI_MIPI_CNTL1 0x01
> +#define		HHI_MIPI_CNTL1_CH0_CML_PDR_EN	BIT(12)
> +#define		HHI_MIPI_CNTL1_LP_ABILITY	GENMASK(5, 4)
> +#define		HHI_MIPI_CNTL1_LP_RESISTER	BIT(3)
> +#define		HHI_MIPI_CNTL1_INPUT_SETTING	BIT(2)
> +#define		HHI_MIPI_CNTL1_INPUT_SEL	BIT(1)
> +#define		HHI_MIPI_CNTL1_PRBS7_EN		BIT(0)
> +
> +#define HHI_MIPI_CNTL2 0x02
> +#define		HHI_MIPI_CNTL2_CH_PU		GENMASK(31, 25)
> +#define		HHI_MIPI_CNTL2_CH_CTL		GENMASK(24, 19)
> +#define		HHI_MIPI_CNTL2_CH0_DIGDR_EN	BIT(18)
> +#define		HHI_MIPI_CNTL2_CH_DIGDR_EN	BIT(17)
> +#define		HHI_MIPI_CNTL2_LPULPS_EN	BIT(16)
> +#define		HHI_MIPI_CNTL2_CH_EN(n)		BIT(15 - (n))
> +#define		HHI_MIPI_CNTL2_CH0_LP_CTL	GENMASK(10, 1)
> +
> +struct phy_axg_mipi_pcie_analog_priv {
> +	struct phy *phy;
> +	unsigned int mode;
> +	struct regmap *regmap;
> +};
> +
> +static const struct regmap_config phy_axg_mipi_pcie_analog_regmap_conf = {
> +	.reg_bits = 8,
> +	.val_bits = 32,
> +	.reg_stride = 4,
> +	.max_register = HHI_MIPI_CNTL2,
> +};
> +
> +static int phy_axg_mipi_pcie_analog_power_on(struct phy *phy)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> +
> +	/* MIPI not supported yet */
> +	if (priv->mode != PHY_TYPE_PCIE)
> +		return -EINVAL;
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_power_off(struct phy *phy)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> +
> +	/* MIPI not supported yet */
> +	if (priv->mode != PHY_TYPE_PCIE)
> +		return -EINVAL;
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_BANDGAP, 0);
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_ENABLE, 0);
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_init(struct phy *phy)
> +{
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_exit(struct phy *phy)
> +{
> +	return 0;
> +}
> +
> +static const struct phy_ops phy_axg_mipi_pcie_analog_ops = {
> +	.init = phy_axg_mipi_pcie_analog_init,
> +	.exit = phy_axg_mipi_pcie_analog_exit,
> +	.power_on = phy_axg_mipi_pcie_analog_power_on,
> +	.power_off = phy_axg_mipi_pcie_analog_power_off,
> +	.owner = THIS_MODULE,
> +};
> +
> +static struct phy *phy_axg_mipi_pcie_analog_xlate(struct device *dev,
> +						  struct of_phandle_args *args)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = dev_get_drvdata(dev);
> +	unsigned int mode;
> +
> +	if (args->args_count != 1) {
> +		dev_err(dev, "invalid number of arguments\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	mode = args->args[0];
> +
> +	/* MIPI mode is not supported yet */
> +	if (mode != PHY_TYPE_PCIE) {
> +		dev_err(dev, "invalid phy mode select argument\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	priv->mode = mode;
> +	return priv->phy;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_probe(struct platform_device *pdev)
> +{
> +	struct phy_provider *phy;
> +	struct device *dev = &pdev->dev;
> +	struct phy_axg_mipi_pcie_analog_priv *priv;
> +	struct device_node *np = dev->of_node;
> +	struct regmap *map;
> +	struct resource *res;
> +	void __iomem *base;
> +	int ret;
> +
> +	priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(base)) {
> +		dev_err(dev, "failed to get regmap base\n");
> +		return PTR_ERR(base);
> +	}
> +
> +	map = devm_regmap_init_mmio(dev, base,
> +				    &phy_axg_mipi_pcie_analog_regmap_conf);
> +	if (IS_ERR(map)) {
> +		dev_err(dev, "failed to get HHI regmap\n");
> +		return PTR_ERR(map);
> +	}
> +	priv->regmap = map;
> +
> +	priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_analog_ops);
> +	if (IS_ERR(priv->phy)) {
> +		ret = PTR_ERR(priv->phy);
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(dev, "failed to create PHY\n");
> +		return ret;
> +	}
> +
> +	phy_set_drvdata(priv->phy, priv);
> +	dev_set_drvdata(dev, priv);
> +
> +	phy = devm_of_phy_provider_register(dev,
> +					    phy_axg_mipi_pcie_analog_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy);
> +}
> +
> +static const struct of_device_id phy_axg_mipi_pcie_analog_of_match[] = {
> +	{
> +		.compatible = "amlogic,axg-mipi-pcie-analog-phy",
> +	},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_analog_of_match);
> +
> +static struct platform_driver phy_axg_mipi_pcie_analog_driver = {
> +	.probe = phy_axg_mipi_pcie_analog_probe,
> +	.driver = {
> +		.name = "phy-axg-mipi-pcie-analog",
> +		.of_match_table = phy_axg_mipi_pcie_analog_of_match,
> +	},
> +};
> +module_platform_driver(phy_axg_mipi_pcie_analog_driver);
> +
> +MODULE_AUTHOR("Remi Pommarel <repk@triplefau.lt>");
> +MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE analog PHY driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.24.1
>
Neil Armstrong March 4, 2020, 9:08 a.m. UTC | #3
Hi Lorenzo,


On 03/03/2020 18:19, Lorenzo Pieralisi wrote:
> On Fri, Jan 24, 2020 at 12:29:41AM +0100, Remi Pommarel wrote:
>> This adds support for the MIPI analog PHY which is also used for PCIE
>> found in the Amlogic AXG SoC Family.
>>
>> MIPI or PCIE selection is done by the #phy-cells, making the mode
>> static and exclusive.
>>
>> For now only PCIE fonctionality is supported.
>>
>> This PHY will be used to replace the mipi_enable clock gating logic
>> which was mistakenly added in the clock subsystem. This also activate
>> a non documented band gap bit in those registers that allows reliable
>> PCIE clock signal generation on AXG platforms.
>>
>> Signed-off-by: Remi Pommarel <repk@triplefau.lt>
>> ---
>>  drivers/phy/amlogic/Kconfig                   |  11 +
>>  drivers/phy/amlogic/Makefile                  |  11 +-
>>  .../amlogic/phy-meson-axg-mipi-pcie-analog.c  | 188 ++++++++++++++++++
>>  3 files changed, 205 insertions(+), 5 deletions(-)
>>  create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> 
> Kishon, Neil,
> 
> can you please review/ack this patch and patch 6 ?

Sure, it was already acked by jerome, but it's also ok for me:

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

Neil
> 
> I would like to queue the series shortly, thanks.
> 
> Lorenzo
> 
>> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
>> index af774ac2b934..8c9cf2403591 100644
>> --- a/drivers/phy/amlogic/Kconfig
>> +++ b/drivers/phy/amlogic/Kconfig
>> @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
>>  	  Enable this to support the Meson USB3 + PCIE Combo PHY found
>>  	  in Meson G12A SoCs.
>>  	  If unsure, say N.
>> +
>> +config PHY_MESON_AXG_MIPI_PCIE_ANALOG
>> +	tristate "Meson AXG MIPI + PCIE analog PHY driver"
>> +	default ARCH_MESON
>> +	depends on OF && (ARCH_MESON || COMPILE_TEST)
>> +	select GENERIC_PHY
>> +	select REGMAP_MMIO
>> +	help
>> +	  Enable this to support the Meson MIPI + PCIE analog PHY
>> +	  found in Meson AXG SoCs.
>> +	  If unsure, say N.
>> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
>> index 11d1c42ac2be..0aecf92d796a 100644
>> --- a/drivers/phy/amlogic/Makefile
>> +++ b/drivers/phy/amlogic/Makefile
>> @@ -1,6 +1,7 @@
>>  # SPDX-License-Identifier: GPL-2.0-only
>> -obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
>> -obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
>> -obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
>> -obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
>> -obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
>> +obj-$(CONFIG_PHY_MESON8B_USB2)			+= phy-meson8b-usb2.o
>> +obj-$(CONFIG_PHY_MESON_GXL_USB2)		+= phy-meson-gxl-usb2.o
>> +obj-$(CONFIG_PHY_MESON_G12A_USB2)		+= phy-meson-g12a-usb2.o
>> +obj-$(CONFIG_PHY_MESON_GXL_USB3)		+= phy-meson-gxl-usb3.o
>> +obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)		+= phy-meson-g12a-usb3-pcie.o
>> +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG)	+= phy-meson-axg-mipi-pcie-analog.o
>> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
>> new file mode 100644
>> index 000000000000..1431cbf885e1
>> --- /dev/null
>> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
>> @@ -0,0 +1,188 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Amlogic AXG MIPI + PCIE analog PHY driver
>> + *
>> + * Copyright (C) 2019 Remi Pommarel <repk@triplefau.lt>
>> + */
>> +#include <linux/module.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/regmap.h>
>> +#include <linux/platform_device.h>
>> +#include <dt-bindings/phy/phy.h>
>> +
>> +#define HHI_MIPI_CNTL0 0x00
>> +#define		HHI_MIPI_CNTL0_COMMON_BLOCK	GENMASK(31, 28)
>> +#define		HHI_MIPI_CNTL0_ENABLE		BIT(29)
>> +#define		HHI_MIPI_CNTL0_BANDGAP		BIT(26)
>> +#define		HHI_MIPI_CNTL0_DECODE_TO_RTERM	GENMASK(15, 12)
>> +#define		HHI_MIPI_CNTL0_OUTPUT_EN	BIT(3)
>> +
>> +#define HHI_MIPI_CNTL1 0x01
>> +#define		HHI_MIPI_CNTL1_CH0_CML_PDR_EN	BIT(12)
>> +#define		HHI_MIPI_CNTL1_LP_ABILITY	GENMASK(5, 4)
>> +#define		HHI_MIPI_CNTL1_LP_RESISTER	BIT(3)
>> +#define		HHI_MIPI_CNTL1_INPUT_SETTING	BIT(2)
>> +#define		HHI_MIPI_CNTL1_INPUT_SEL	BIT(1)
>> +#define		HHI_MIPI_CNTL1_PRBS7_EN		BIT(0)
>> +
>> +#define HHI_MIPI_CNTL2 0x02
>> +#define		HHI_MIPI_CNTL2_CH_PU		GENMASK(31, 25)
>> +#define		HHI_MIPI_CNTL2_CH_CTL		GENMASK(24, 19)
>> +#define		HHI_MIPI_CNTL2_CH0_DIGDR_EN	BIT(18)
>> +#define		HHI_MIPI_CNTL2_CH_DIGDR_EN	BIT(17)
>> +#define		HHI_MIPI_CNTL2_LPULPS_EN	BIT(16)
>> +#define		HHI_MIPI_CNTL2_CH_EN(n)		BIT(15 - (n))
>> +#define		HHI_MIPI_CNTL2_CH0_LP_CTL	GENMASK(10, 1)
>> +
>> +struct phy_axg_mipi_pcie_analog_priv {
>> +	struct phy *phy;
>> +	unsigned int mode;
>> +	struct regmap *regmap;
>> +};
>> +
>> +static const struct regmap_config phy_axg_mipi_pcie_analog_regmap_conf = {
>> +	.reg_bits = 8,
>> +	.val_bits = 32,
>> +	.reg_stride = 4,
>> +	.max_register = HHI_MIPI_CNTL2,
>> +};
>> +
>> +static int phy_axg_mipi_pcie_analog_power_on(struct phy *phy)
>> +{
>> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
>> +
>> +	/* MIPI not supported yet */
>> +	if (priv->mode != PHY_TYPE_PCIE)
>> +		return -EINVAL;
>> +
>> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
>> +			   HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
>> +
>> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
>> +			   HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
>> +	return 0;
>> +}
>> +
>> +static int phy_axg_mipi_pcie_analog_power_off(struct phy *phy)
>> +{
>> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
>> +
>> +	/* MIPI not supported yet */
>> +	if (priv->mode != PHY_TYPE_PCIE)
>> +		return -EINVAL;
>> +
>> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
>> +			   HHI_MIPI_CNTL0_BANDGAP, 0);
>> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
>> +			   HHI_MIPI_CNTL0_ENABLE, 0);
>> +	return 0;
>> +}
>> +
>> +static int phy_axg_mipi_pcie_analog_init(struct phy *phy)
>> +{
>> +	return 0;
>> +}
>> +
>> +static int phy_axg_mipi_pcie_analog_exit(struct phy *phy)
>> +{
>> +	return 0;
>> +}
>> +
>> +static const struct phy_ops phy_axg_mipi_pcie_analog_ops = {
>> +	.init = phy_axg_mipi_pcie_analog_init,
>> +	.exit = phy_axg_mipi_pcie_analog_exit,
>> +	.power_on = phy_axg_mipi_pcie_analog_power_on,
>> +	.power_off = phy_axg_mipi_pcie_analog_power_off,
>> +	.owner = THIS_MODULE,
>> +};
>> +
>> +static struct phy *phy_axg_mipi_pcie_analog_xlate(struct device *dev,
>> +						  struct of_phandle_args *args)
>> +{
>> +	struct phy_axg_mipi_pcie_analog_priv *priv = dev_get_drvdata(dev);
>> +	unsigned int mode;
>> +
>> +	if (args->args_count != 1) {
>> +		dev_err(dev, "invalid number of arguments\n");
>> +		return ERR_PTR(-EINVAL);
>> +	}
>> +
>> +	mode = args->args[0];
>> +
>> +	/* MIPI mode is not supported yet */
>> +	if (mode != PHY_TYPE_PCIE) {
>> +		dev_err(dev, "invalid phy mode select argument\n");
>> +		return ERR_PTR(-EINVAL);
>> +	}
>> +
>> +	priv->mode = mode;
>> +	return priv->phy;
>> +}
>> +
>> +static int phy_axg_mipi_pcie_analog_probe(struct platform_device *pdev)
>> +{
>> +	struct phy_provider *phy;
>> +	struct device *dev = &pdev->dev;
>> +	struct phy_axg_mipi_pcie_analog_priv *priv;
>> +	struct device_node *np = dev->of_node;
>> +	struct regmap *map;
>> +	struct resource *res;
>> +	void __iomem *base;
>> +	int ret;
>> +
>> +	priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
>> +	if (!priv)
>> +		return -ENOMEM;
>> +
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	base = devm_ioremap_resource(dev, res);
>> +	if (IS_ERR(base)) {
>> +		dev_err(dev, "failed to get regmap base\n");
>> +		return PTR_ERR(base);
>> +	}
>> +
>> +	map = devm_regmap_init_mmio(dev, base,
>> +				    &phy_axg_mipi_pcie_analog_regmap_conf);
>> +	if (IS_ERR(map)) {
>> +		dev_err(dev, "failed to get HHI regmap\n");
>> +		return PTR_ERR(map);
>> +	}
>> +	priv->regmap = map;
>> +
>> +	priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_analog_ops);
>> +	if (IS_ERR(priv->phy)) {
>> +		ret = PTR_ERR(priv->phy);
>> +		if (ret != -EPROBE_DEFER)
>> +			dev_err(dev, "failed to create PHY\n");
>> +		return ret;
>> +	}
>> +
>> +	phy_set_drvdata(priv->phy, priv);
>> +	dev_set_drvdata(dev, priv);
>> +
>> +	phy = devm_of_phy_provider_register(dev,
>> +					    phy_axg_mipi_pcie_analog_xlate);
>> +
>> +	return PTR_ERR_OR_ZERO(phy);
>> +}
>> +
>> +static const struct of_device_id phy_axg_mipi_pcie_analog_of_match[] = {
>> +	{
>> +		.compatible = "amlogic,axg-mipi-pcie-analog-phy",
>> +	},
>> +	{ },
>> +};
>> +MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_analog_of_match);
>> +
>> +static struct platform_driver phy_axg_mipi_pcie_analog_driver = {
>> +	.probe = phy_axg_mipi_pcie_analog_probe,
>> +	.driver = {
>> +		.name = "phy-axg-mipi-pcie-analog",
>> +		.of_match_table = phy_axg_mipi_pcie_analog_of_match,
>> +	},
>> +};
>> +module_platform_driver(phy_axg_mipi_pcie_analog_driver);
>> +
>> +MODULE_AUTHOR("Remi Pommarel <repk@triplefau.lt>");
>> +MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE analog PHY driver");
>> +MODULE_LICENSE("GPL v2");
>> -- 
>> 2.24.1
>>
Lorenzo Pieralisi March 4, 2020, 10:44 a.m. UTC | #4
On Wed, Mar 04, 2020 at 10:08:55AM +0100, Neil Armstrong wrote:
> Hi Lorenzo,
> 
> 
> On 03/03/2020 18:19, Lorenzo Pieralisi wrote:
> > On Fri, Jan 24, 2020 at 12:29:41AM +0100, Remi Pommarel wrote:
> >> This adds support for the MIPI analog PHY which is also used for PCIE
> >> found in the Amlogic AXG SoC Family.
> >>
> >> MIPI or PCIE selection is done by the #phy-cells, making the mode
> >> static and exclusive.
> >>
> >> For now only PCIE fonctionality is supported.
> >>
> >> This PHY will be used to replace the mipi_enable clock gating logic
> >> which was mistakenly added in the clock subsystem. This also activate
> >> a non documented band gap bit in those registers that allows reliable
> >> PCIE clock signal generation on AXG platforms.
> >>
> >> Signed-off-by: Remi Pommarel <repk@triplefau.lt>
> >> ---
> >>  drivers/phy/amlogic/Kconfig                   |  11 +
> >>  drivers/phy/amlogic/Makefile                  |  11 +-
> >>  .../amlogic/phy-meson-axg-mipi-pcie-analog.c  | 188 ++++++++++++++++++
> >>  3 files changed, 205 insertions(+), 5 deletions(-)
> >>  create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> > 
> > Kishon, Neil,
> > 
> > can you please review/ack this patch and patch 6 ?
> 
> Sure, it was already acked by jerome, but it's also ok for me:
> 
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

Thanks. Sorry for the pedantry but on patch (6) too.

Lorenzo

> Neil
> > 
> > I would like to queue the series shortly, thanks.
> > 
> > Lorenzo
> > 
> >> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> >> index af774ac2b934..8c9cf2403591 100644
> >> --- a/drivers/phy/amlogic/Kconfig
> >> +++ b/drivers/phy/amlogic/Kconfig
> >> @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
> >>  	  Enable this to support the Meson USB3 + PCIE Combo PHY found
> >>  	  in Meson G12A SoCs.
> >>  	  If unsure, say N.
> >> +
> >> +config PHY_MESON_AXG_MIPI_PCIE_ANALOG
> >> +	tristate "Meson AXG MIPI + PCIE analog PHY driver"
> >> +	default ARCH_MESON
> >> +	depends on OF && (ARCH_MESON || COMPILE_TEST)
> >> +	select GENERIC_PHY
> >> +	select REGMAP_MMIO
> >> +	help
> >> +	  Enable this to support the Meson MIPI + PCIE analog PHY
> >> +	  found in Meson AXG SoCs.
> >> +	  If unsure, say N.
> >> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> >> index 11d1c42ac2be..0aecf92d796a 100644
> >> --- a/drivers/phy/amlogic/Makefile
> >> +++ b/drivers/phy/amlogic/Makefile
> >> @@ -1,6 +1,7 @@
> >>  # SPDX-License-Identifier: GPL-2.0-only
> >> -obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
> >> -obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
> >> -obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
> >> -obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
> >> -obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
> >> +obj-$(CONFIG_PHY_MESON8B_USB2)			+= phy-meson8b-usb2.o
> >> +obj-$(CONFIG_PHY_MESON_GXL_USB2)		+= phy-meson-gxl-usb2.o
> >> +obj-$(CONFIG_PHY_MESON_G12A_USB2)		+= phy-meson-g12a-usb2.o
> >> +obj-$(CONFIG_PHY_MESON_GXL_USB3)		+= phy-meson-gxl-usb3.o
> >> +obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)		+= phy-meson-g12a-usb3-pcie.o
> >> +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG)	+= phy-meson-axg-mipi-pcie-analog.o
> >> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> >> new file mode 100644
> >> index 000000000000..1431cbf885e1
> >> --- /dev/null
> >> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> >> @@ -0,0 +1,188 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Amlogic AXG MIPI + PCIE analog PHY driver
> >> + *
> >> + * Copyright (C) 2019 Remi Pommarel <repk@triplefau.lt>
> >> + */
> >> +#include <linux/module.h>
> >> +#include <linux/phy/phy.h>
> >> +#include <linux/regmap.h>
> >> +#include <linux/platform_device.h>
> >> +#include <dt-bindings/phy/phy.h>
> >> +
> >> +#define HHI_MIPI_CNTL0 0x00
> >> +#define		HHI_MIPI_CNTL0_COMMON_BLOCK	GENMASK(31, 28)
> >> +#define		HHI_MIPI_CNTL0_ENABLE		BIT(29)
> >> +#define		HHI_MIPI_CNTL0_BANDGAP		BIT(26)
> >> +#define		HHI_MIPI_CNTL0_DECODE_TO_RTERM	GENMASK(15, 12)
> >> +#define		HHI_MIPI_CNTL0_OUTPUT_EN	BIT(3)
> >> +
> >> +#define HHI_MIPI_CNTL1 0x01
> >> +#define		HHI_MIPI_CNTL1_CH0_CML_PDR_EN	BIT(12)
> >> +#define		HHI_MIPI_CNTL1_LP_ABILITY	GENMASK(5, 4)
> >> +#define		HHI_MIPI_CNTL1_LP_RESISTER	BIT(3)
> >> +#define		HHI_MIPI_CNTL1_INPUT_SETTING	BIT(2)
> >> +#define		HHI_MIPI_CNTL1_INPUT_SEL	BIT(1)
> >> +#define		HHI_MIPI_CNTL1_PRBS7_EN		BIT(0)
> >> +
> >> +#define HHI_MIPI_CNTL2 0x02
> >> +#define		HHI_MIPI_CNTL2_CH_PU		GENMASK(31, 25)
> >> +#define		HHI_MIPI_CNTL2_CH_CTL		GENMASK(24, 19)
> >> +#define		HHI_MIPI_CNTL2_CH0_DIGDR_EN	BIT(18)
> >> +#define		HHI_MIPI_CNTL2_CH_DIGDR_EN	BIT(17)
> >> +#define		HHI_MIPI_CNTL2_LPULPS_EN	BIT(16)
> >> +#define		HHI_MIPI_CNTL2_CH_EN(n)		BIT(15 - (n))
> >> +#define		HHI_MIPI_CNTL2_CH0_LP_CTL	GENMASK(10, 1)
> >> +
> >> +struct phy_axg_mipi_pcie_analog_priv {
> >> +	struct phy *phy;
> >> +	unsigned int mode;
> >> +	struct regmap *regmap;
> >> +};
> >> +
> >> +static const struct regmap_config phy_axg_mipi_pcie_analog_regmap_conf = {
> >> +	.reg_bits = 8,
> >> +	.val_bits = 32,
> >> +	.reg_stride = 4,
> >> +	.max_register = HHI_MIPI_CNTL2,
> >> +};
> >> +
> >> +static int phy_axg_mipi_pcie_analog_power_on(struct phy *phy)
> >> +{
> >> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> >> +
> >> +	/* MIPI not supported yet */
> >> +	if (priv->mode != PHY_TYPE_PCIE)
> >> +		return -EINVAL;
> >> +
> >> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> >> +			   HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
> >> +
> >> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> >> +			   HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
> >> +	return 0;
> >> +}
> >> +
> >> +static int phy_axg_mipi_pcie_analog_power_off(struct phy *phy)
> >> +{
> >> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> >> +
> >> +	/* MIPI not supported yet */
> >> +	if (priv->mode != PHY_TYPE_PCIE)
> >> +		return -EINVAL;
> >> +
> >> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> >> +			   HHI_MIPI_CNTL0_BANDGAP, 0);
> >> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> >> +			   HHI_MIPI_CNTL0_ENABLE, 0);
> >> +	return 0;
> >> +}
> >> +
> >> +static int phy_axg_mipi_pcie_analog_init(struct phy *phy)
> >> +{
> >> +	return 0;
> >> +}
> >> +
> >> +static int phy_axg_mipi_pcie_analog_exit(struct phy *phy)
> >> +{
> >> +	return 0;
> >> +}
> >> +
> >> +static const struct phy_ops phy_axg_mipi_pcie_analog_ops = {
> >> +	.init = phy_axg_mipi_pcie_analog_init,
> >> +	.exit = phy_axg_mipi_pcie_analog_exit,
> >> +	.power_on = phy_axg_mipi_pcie_analog_power_on,
> >> +	.power_off = phy_axg_mipi_pcie_analog_power_off,
> >> +	.owner = THIS_MODULE,
> >> +};
> >> +
> >> +static struct phy *phy_axg_mipi_pcie_analog_xlate(struct device *dev,
> >> +						  struct of_phandle_args *args)
> >> +{
> >> +	struct phy_axg_mipi_pcie_analog_priv *priv = dev_get_drvdata(dev);
> >> +	unsigned int mode;
> >> +
> >> +	if (args->args_count != 1) {
> >> +		dev_err(dev, "invalid number of arguments\n");
> >> +		return ERR_PTR(-EINVAL);
> >> +	}
> >> +
> >> +	mode = args->args[0];
> >> +
> >> +	/* MIPI mode is not supported yet */
> >> +	if (mode != PHY_TYPE_PCIE) {
> >> +		dev_err(dev, "invalid phy mode select argument\n");
> >> +		return ERR_PTR(-EINVAL);
> >> +	}
> >> +
> >> +	priv->mode = mode;
> >> +	return priv->phy;
> >> +}
> >> +
> >> +static int phy_axg_mipi_pcie_analog_probe(struct platform_device *pdev)
> >> +{
> >> +	struct phy_provider *phy;
> >> +	struct device *dev = &pdev->dev;
> >> +	struct phy_axg_mipi_pcie_analog_priv *priv;
> >> +	struct device_node *np = dev->of_node;
> >> +	struct regmap *map;
> >> +	struct resource *res;
> >> +	void __iomem *base;
> >> +	int ret;
> >> +
> >> +	priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
> >> +	if (!priv)
> >> +		return -ENOMEM;
> >> +
> >> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> >> +	base = devm_ioremap_resource(dev, res);
> >> +	if (IS_ERR(base)) {
> >> +		dev_err(dev, "failed to get regmap base\n");
> >> +		return PTR_ERR(base);
> >> +	}
> >> +
> >> +	map = devm_regmap_init_mmio(dev, base,
> >> +				    &phy_axg_mipi_pcie_analog_regmap_conf);
> >> +	if (IS_ERR(map)) {
> >> +		dev_err(dev, "failed to get HHI regmap\n");
> >> +		return PTR_ERR(map);
> >> +	}
> >> +	priv->regmap = map;
> >> +
> >> +	priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_analog_ops);
> >> +	if (IS_ERR(priv->phy)) {
> >> +		ret = PTR_ERR(priv->phy);
> >> +		if (ret != -EPROBE_DEFER)
> >> +			dev_err(dev, "failed to create PHY\n");
> >> +		return ret;
> >> +	}
> >> +
> >> +	phy_set_drvdata(priv->phy, priv);
> >> +	dev_set_drvdata(dev, priv);
> >> +
> >> +	phy = devm_of_phy_provider_register(dev,
> >> +					    phy_axg_mipi_pcie_analog_xlate);
> >> +
> >> +	return PTR_ERR_OR_ZERO(phy);
> >> +}
> >> +
> >> +static const struct of_device_id phy_axg_mipi_pcie_analog_of_match[] = {
> >> +	{
> >> +		.compatible = "amlogic,axg-mipi-pcie-analog-phy",
> >> +	},
> >> +	{ },
> >> +};
> >> +MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_analog_of_match);
> >> +
> >> +static struct platform_driver phy_axg_mipi_pcie_analog_driver = {
> >> +	.probe = phy_axg_mipi_pcie_analog_probe,
> >> +	.driver = {
> >> +		.name = "phy-axg-mipi-pcie-analog",
> >> +		.of_match_table = phy_axg_mipi_pcie_analog_of_match,
> >> +	},
> >> +};
> >> +module_platform_driver(phy_axg_mipi_pcie_analog_driver);
> >> +
> >> +MODULE_AUTHOR("Remi Pommarel <repk@triplefau.lt>");
> >> +MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE analog PHY driver");
> >> +MODULE_LICENSE("GPL v2");
> >> -- 
> >> 2.24.1
> >>
>

Patch
diff mbox series

diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
index af774ac2b934..8c9cf2403591 100644
--- a/drivers/phy/amlogic/Kconfig
+++ b/drivers/phy/amlogic/Kconfig
@@ -59,3 +59,14 @@  config PHY_MESON_G12A_USB3_PCIE
 	  Enable this to support the Meson USB3 + PCIE Combo PHY found
 	  in Meson G12A SoCs.
 	  If unsure, say N.
+
+config PHY_MESON_AXG_MIPI_PCIE_ANALOG
+	tristate "Meson AXG MIPI + PCIE analog PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  Enable this to support the Meson MIPI + PCIE analog PHY
+	  found in Meson AXG SoCs.
+	  If unsure, say N.
diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
index 11d1c42ac2be..0aecf92d796a 100644
--- a/drivers/phy/amlogic/Makefile
+++ b/drivers/phy/amlogic/Makefile
@@ -1,6 +1,7 @@ 
 # SPDX-License-Identifier: GPL-2.0-only
-obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
-obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
-obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
-obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
-obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
+obj-$(CONFIG_PHY_MESON8B_USB2)			+= phy-meson8b-usb2.o
+obj-$(CONFIG_PHY_MESON_GXL_USB2)		+= phy-meson-gxl-usb2.o
+obj-$(CONFIG_PHY_MESON_G12A_USB2)		+= phy-meson-g12a-usb2.o
+obj-$(CONFIG_PHY_MESON_GXL_USB3)		+= phy-meson-gxl-usb3.o
+obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)		+= phy-meson-g12a-usb3-pcie.o
+obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG)	+= phy-meson-axg-mipi-pcie-analog.o
diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
new file mode 100644
index 000000000000..1431cbf885e1
--- /dev/null
+++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
@@ -0,0 +1,188 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Amlogic AXG MIPI + PCIE analog PHY driver
+ *
+ * Copyright (C) 2019 Remi Pommarel <repk@triplefau.lt>
+ */
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/platform_device.h>
+#include <dt-bindings/phy/phy.h>
+
+#define HHI_MIPI_CNTL0 0x00
+#define		HHI_MIPI_CNTL0_COMMON_BLOCK	GENMASK(31, 28)
+#define		HHI_MIPI_CNTL0_ENABLE		BIT(29)
+#define		HHI_MIPI_CNTL0_BANDGAP		BIT(26)
+#define		HHI_MIPI_CNTL0_DECODE_TO_RTERM	GENMASK(15, 12)
+#define		HHI_MIPI_CNTL0_OUTPUT_EN	BIT(3)
+
+#define HHI_MIPI_CNTL1 0x01
+#define		HHI_MIPI_CNTL1_CH0_CML_PDR_EN	BIT(12)
+#define		HHI_MIPI_CNTL1_LP_ABILITY	GENMASK(5, 4)
+#define		HHI_MIPI_CNTL1_LP_RESISTER	BIT(3)
+#define		HHI_MIPI_CNTL1_INPUT_SETTING	BIT(2)
+#define		HHI_MIPI_CNTL1_INPUT_SEL	BIT(1)
+#define		HHI_MIPI_CNTL1_PRBS7_EN		BIT(0)
+
+#define HHI_MIPI_CNTL2 0x02
+#define		HHI_MIPI_CNTL2_CH_PU		GENMASK(31, 25)
+#define		HHI_MIPI_CNTL2_CH_CTL		GENMASK(24, 19)
+#define		HHI_MIPI_CNTL2_CH0_DIGDR_EN	BIT(18)
+#define		HHI_MIPI_CNTL2_CH_DIGDR_EN	BIT(17)
+#define		HHI_MIPI_CNTL2_LPULPS_EN	BIT(16)
+#define		HHI_MIPI_CNTL2_CH_EN(n)		BIT(15 - (n))
+#define		HHI_MIPI_CNTL2_CH0_LP_CTL	GENMASK(10, 1)
+
+struct phy_axg_mipi_pcie_analog_priv {
+	struct phy *phy;
+	unsigned int mode;
+	struct regmap *regmap;
+};
+
+static const struct regmap_config phy_axg_mipi_pcie_analog_regmap_conf = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = HHI_MIPI_CNTL2,
+};
+
+static int phy_axg_mipi_pcie_analog_power_on(struct phy *phy)
+{
+	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
+
+	/* MIPI not supported yet */
+	if (priv->mode != PHY_TYPE_PCIE)
+		return -EINVAL;
+
+	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
+			   HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
+
+	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
+			   HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
+	return 0;
+}
+
+static int phy_axg_mipi_pcie_analog_power_off(struct phy *phy)
+{
+	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
+
+	/* MIPI not supported yet */
+	if (priv->mode != PHY_TYPE_PCIE)
+		return -EINVAL;
+
+	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
+			   HHI_MIPI_CNTL0_BANDGAP, 0);
+	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
+			   HHI_MIPI_CNTL0_ENABLE, 0);
+	return 0;
+}
+
+static int phy_axg_mipi_pcie_analog_init(struct phy *phy)
+{
+	return 0;
+}
+
+static int phy_axg_mipi_pcie_analog_exit(struct phy *phy)
+{
+	return 0;
+}
+
+static const struct phy_ops phy_axg_mipi_pcie_analog_ops = {
+	.init = phy_axg_mipi_pcie_analog_init,
+	.exit = phy_axg_mipi_pcie_analog_exit,
+	.power_on = phy_axg_mipi_pcie_analog_power_on,
+	.power_off = phy_axg_mipi_pcie_analog_power_off,
+	.owner = THIS_MODULE,
+};
+
+static struct phy *phy_axg_mipi_pcie_analog_xlate(struct device *dev,
+						  struct of_phandle_args *args)
+{
+	struct phy_axg_mipi_pcie_analog_priv *priv = dev_get_drvdata(dev);
+	unsigned int mode;
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of arguments\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	mode = args->args[0];
+
+	/* MIPI mode is not supported yet */
+	if (mode != PHY_TYPE_PCIE) {
+		dev_err(dev, "invalid phy mode select argument\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	priv->mode = mode;
+	return priv->phy;
+}
+
+static int phy_axg_mipi_pcie_analog_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy;
+	struct device *dev = &pdev->dev;
+	struct phy_axg_mipi_pcie_analog_priv *priv;
+	struct device_node *np = dev->of_node;
+	struct regmap *map;
+	struct resource *res;
+	void __iomem *base;
+	int ret;
+
+	priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base)) {
+		dev_err(dev, "failed to get regmap base\n");
+		return PTR_ERR(base);
+	}
+
+	map = devm_regmap_init_mmio(dev, base,
+				    &phy_axg_mipi_pcie_analog_regmap_conf);
+	if (IS_ERR(map)) {
+		dev_err(dev, "failed to get HHI regmap\n");
+		return PTR_ERR(map);
+	}
+	priv->regmap = map;
+
+	priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_analog_ops);
+	if (IS_ERR(priv->phy)) {
+		ret = PTR_ERR(priv->phy);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "failed to create PHY\n");
+		return ret;
+	}
+
+	phy_set_drvdata(priv->phy, priv);
+	dev_set_drvdata(dev, priv);
+
+	phy = devm_of_phy_provider_register(dev,
+					    phy_axg_mipi_pcie_analog_xlate);
+
+	return PTR_ERR_OR_ZERO(phy);
+}
+
+static const struct of_device_id phy_axg_mipi_pcie_analog_of_match[] = {
+	{
+		.compatible = "amlogic,axg-mipi-pcie-analog-phy",
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_analog_of_match);
+
+static struct platform_driver phy_axg_mipi_pcie_analog_driver = {
+	.probe = phy_axg_mipi_pcie_analog_probe,
+	.driver = {
+		.name = "phy-axg-mipi-pcie-analog",
+		.of_match_table = phy_axg_mipi_pcie_analog_of_match,
+	},
+};
+module_platform_driver(phy_axg_mipi_pcie_analog_driver);
+
+MODULE_AUTHOR("Remi Pommarel <repk@triplefau.lt>");
+MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE analog PHY driver");
+MODULE_LICENSE("GPL v2");