diff mbox series

[2/2] display/drm/bridge: tc358775 DSI/LVDS driver

Message ID 1583920112-2680-2-git-send-email-simhavcs@gmail.com (mailing list archive)
State New, archived
Headers show
Series [1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings | expand

Commit Message

Vinay Simha B N March 11, 2020, 9:48 a.m. UTC
dsi2lvds tc358775 bridge driver added
Tested in apq8016, ifc6309 board and panel
auo,b101xtn01

Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
---
v1:
 Initial version

v2:
* Andrzej Hajda review comments incorporated
  SPDX identifier
  development debug removed
  alphabetic order headers
  u32 instead of unit32_t
  magic numbers to macros for CLRSI and mux registers
  ignored return value

* Laurent Pinchart review comments incorporated
  mdelay to usleep_range
  bus_formats added
---
 drivers/gpu/drm/bridge/Kconfig    |  10 +
 drivers/gpu/drm/bridge/Makefile   |   1 +
 drivers/gpu/drm/bridge/tc358775.c | 688 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 699 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/tc358775.c

Comments

Andrzej Hajda March 12, 2020, 10:50 a.m. UTC | #1
On 11.03.2020 10:48, Vinay Simha BN wrote:
> dsi2lvds tc358775 bridge driver added
> Tested in apq8016, ifc6309 board and panel
> auo,b101xtn01
>
> Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
> ---
> v1:
>  Initial version
>
> v2:
> * Andrzej Hajda review comments incorporated
>   SPDX identifier
>   development debug removed
>   alphabetic order headers
>   u32 instead of unit32_t
>   magic numbers to macros for CLRSI and mux registers
>   ignored return value
>
> * Laurent Pinchart review comments incorporated
>   mdelay to usleep_range
>   bus_formats added
> ---
>  drivers/gpu/drm/bridge/Kconfig    |  10 +
>  drivers/gpu/drm/bridge/Makefile   |   1 +
>  drivers/gpu/drm/bridge/tc358775.c | 688 ++++++++++++++++++++++++++++++++++++++
>  3 files changed, 699 insertions(+)
>  create mode 100644 drivers/gpu/drm/bridge/tc358775.c
>
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index 8397bf7..d5528fa 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -133,6 +133,16 @@ config DRM_TOSHIBA_TC358767
>  	---help---
>  	  Toshiba TC358767 eDP bridge chip driver.
>  
> +config DRM_TOSHIBA_TC358775
> +        tristate "Toshiba TC358775 LVDS bridge"
> +        depends on OF
> +        select DRM_KMS_HELPER
> +        select REGMAP_I2C
> +        select DRM_PANEL
> +	select DRM_MIPI_DSI
> +        ---help---
> +          Toshiba TC358775 LVDS bridge chip driver.
> +
>  config DRM_TI_TFP410
>  	tristate "TI TFP410 DVI/HDMI bridge"
>  	depends on OF
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index 1eb5376..9b2c512 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -12,6 +12,7 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o
>  obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
>  obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
>  obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
> +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o
>  obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
>  obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
>  obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
> diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c
> new file mode 100644
> index 0000000..28b828e
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/tc358775.c
> @@ -0,0 +1,688 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * tc358775 DSI to LVDS bridge driver
> + *
> + * Copyright (C) 2020 InforceComputing
> + * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com>
> + *
> + */
> +#define DEBUG
> +#include <linux/clk.h>
> +#include <linux/device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/slab.h>
> +
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_bridge.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_dp_helper.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_of.h>
> +#include <drm/drm_panel.h>
> +#include <drm/drm_probe_helper.h>
> +
> +#define FLD_MASK(start, end)    (((1 << ((start) - (end) + 1)) - 1) << (end))
> +#define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end))
> +
> +/* Registers */
> +
> +/* DSI D-PHY Layer Registers */
> +#define D0W_DPHYCONTTX  0x0004  /* Data Lane 0 DPHY Tx Control */
> +#define CLW_DPHYCONTRX  0x0020  /* Clock Lane DPHY Rx Control */
> +#define D0W_DPHYCONTRX  0x0024  /* Data Lane 0 DPHY Rx Control */
> +#define D1W_DPHYCONTRX  0x0028  /* Data Lane 1 DPHY Rx Control */
> +#define D2W_DPHYCONTRX  0x002C  /* Data Lane 2 DPHY Rx Control */
> +#define D3W_DPHYCONTRX  0x0030  /* Data Lane 3 DPHY Rx Control */
> +#define COM_DPHYCONTRX  0x0038  /* DPHY Rx Common Control */
> +#define CLW_CNTRL       0x0040  /* Clock Lane Control */
> +#define D0W_CNTRL       0x0044  /* Data Lane 0 Control */
> +#define D1W_CNTRL       0x0048  /* Data Lane 1 Control */
> +#define D2W_CNTRL       0x004C  /* Data Lane 2 Control */
> +#define D3W_CNTRL       0x0050  /* Data Lane 3 Control */
> +#define DFTMODE_CNTRL   0x0054  /* DFT Mode Control */
> +
> +/* DSI PPI Layer Registers */
> +#define PPI_STARTPPI    0x0104  /* START control bit of PPI-TX function. */
> +#define PPI_BUSYPPI     0x0108
> +#define PPI_LINEINITCNT 0x0110  /* Line Initialization Wait Counter  */
> +#define PPI_LPTXTIMECNT 0x0114
> +#define PPI_LANEENABLE  0x0134  /* Enables each lane at the PPI layer. */
> +#define PPI_TX_RX_TA    0x013C  /* DSI Bus Turn Around timing parameters */
> +
> +/* Analog timer function enable */
> +#define PPI_CLS_ATMR    0x0140  /* Delay for Clock Lane in LPRX  */
> +#define PPI_D0S_ATMR    0x0144  /* Delay for Data Lane 0 in LPRX */
> +#define PPI_D1S_ATMR    0x0148  /* Delay for Data Lane 1 in LPRX */
> +#define PPI_D2S_ATMR    0x014C  /* Delay for Data Lane 2 in LPRX */
> +#define PPI_D3S_ATMR    0x0150  /* Delay for Data Lane 3 in LPRX */
> +
> +#define PPI_D0S_CLRSIPOCOUNT    0x0164  /* For lane 0 */
> +#define PPI_D1S_CLRSIPOCOUNT    0x0168  /* For lane 1 */
> +#define PPI_D2S_CLRSIPOCOUNT    0x016C  /* For lane 2 */
> +#define PPI_D3S_CLRSIPOCOUNT    0x0170  /* For lane 3 */
> +
> +#define CLS_PRE         0x0180  /* Digital Counter inside of PHY IO */
> +#define D0S_PRE         0x0184  /* Digital Counter inside of PHY IO */
> +#define D1S_PRE         0x0188  /* Digital Counter inside of PHY IO */
> +#define D2S_PRE         0x018C  /* Digital Counter inside of PHY IO */
> +#define D3S_PRE         0x0190  /* Digital Counter inside of PHY IO */
> +#define CLS_PREP        0x01A0  /* Digital Counter inside of PHY IO */
> +#define D0S_PREP        0x01A4  /* Digital Counter inside of PHY IO */
> +#define D1S_PREP        0x01A8  /* Digital Counter inside of PHY IO */
> +#define D2S_PREP        0x01AC  /* Digital Counter inside of PHY IO */
> +#define D3S_PREP        0x01B0  /* Digital Counter inside of PHY IO */
> +#define CLS_ZERO        0x01C0  /* Digital Counter inside of PHY IO */
> +#define D0S_ZERO        0x01C4  /* Digital Counter inside of PHY IO */
> +#define D1S_ZERO        0x01C8  /* Digital Counter inside of PHY IO */
> +#define D2S_ZERO        0x01CC  /* Digital Counter inside of PHY IO */
> +#define D3S_ZERO        0x01D0  /* Digital Counter inside of PHY IO */
> +
> +#define PPI_CLRFLG      0x01E0  /* PRE Counters has reached set values */
> +#define PPI_CLRSIPO     0x01E4  /* Clear SIPO values, Slave mode use only. */
> +#define HSTIMEOUT       0x01F0  /* HS Rx Time Out Counter */
> +#define HSTIMEOUTENABLE 0x01F4  /* Enable HS Rx Time Out Counter */
> +#define DSI_STARTDSI    0x0204  /* START control bit of DSI-TX function */
> +#define DSI_BUSYDSI     0x0208
> +#define DSI_LANEENABLE  0x0210  /* Enables each lane at the Protocol layer. */
> +#define DSI_LANESTATUS0 0x0214  /* Displays lane is in HS RX mode. */
> +#define DSI_LANESTATUS1 0x0218  /* Displays lane is in ULPS or STOP state */
> +
> +#define DSI_INTSTATUS   0x0220  /* Interrupt Status */
> +#define DSI_INTMASK     0x0224  /* Interrupt Mask */
> +#define DSI_INTCLR      0x0228  /* Interrupt Clear */
> +#define DSI_LPTXTO      0x0230  /* Low Power Tx Time Out Counter */
> +
> +#define DSIERRCNT       0x0300  /* DSI Error Count */
> +#define APLCTRL         0x0400  /* Application Layer Control */
> +#define RDPKTLN         0x0404  /* Command Read Packet Length */
> +
> +#define VPCTRL          0x0450  /* Video Path Control */
> +#define HTIM1           0x0454  /* Horizontal Timing Control 1 */
> +#define HTIM2           0x0458  /* Horizontal Timing Control 2 */
> +#define VTIM1           0x045C  /* Vertical Timing Control 1 */
> +#define VTIM2           0x0460  /* Vertical Timing Control 2 */
> +#define VFUEN           0x0464  /* Video Frame Timing Update Enable */
> +
> +/* Mux Input Select for LVDS LINK Input */
> +#define LV_MX0003        0x0480  /* Bit 0 to 3 */
> +#define LV_MX0407        0x0484  /* Bit 4 to 7 */
> +#define LV_MX0811        0x0488  /* Bit 8 to 11 */
> +#define LV_MX1215        0x048C  /* Bit 12 to 15 */
> +#define LV_MX1619        0x0490  /* Bit 16 to 19 */
> +#define LV_MX2023        0x0494  /* Bit 20 to 23 */
> +#define LV_MX2427        0x0498  /* Bit 24 to 27 */
> +#define LV_MX(b0, b1, b2, b3)	(FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \
> +				FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24))
> +
> +/* Input bit numbers used in mux registers */
> +enum {
> +	LVI_R0,
> +	LVI_R1,
> +	LVI_R2,
> +	LVI_R3,
> +	LVI_R4,
> +	LVI_R5,
> +	LVI_R6,
> +	LVI_R7,
> +	LVI_G0,
> +	LVI_G1,
> +	LVI_G2,
> +	LVI_G3,
> +	LVI_G4,
> +	LVI_G5,
> +	LVI_G6,
> +	LVI_G7,
> +	LVI_B0,
> +	LVI_B1,
> +	LVI_B2,
> +	LVI_B3,
> +	LVI_B4,
> +	LVI_B5,
> +	LVI_B6,
> +	LVI_B7,
> +	LVI_HS,
> +	LVI_VS,
> +	LVI_DE,
> +	LVI_L0
> +};
> +
> +#define LVCFG           0x049C  /* LVDS Configuration  */
> +#define LVPHY0          0x04A0  /* LVDS PHY 0 */
> +#define LVPHY1          0x04A4  /* LVDS PHY 1 */
> +#define SYSSTAT         0x0500  /* System Status  */
> +#define SYSRST          0x0504  /* System Reset  */
> +/* GPIO Registers */
> +#define GPIOC           0x0520  /* GPIO Control  */
> +#define GPIOO           0x0524  /* GPIO Output  */
> +#define GPIOI           0x0528  /* GPIO Input  */
> +
> +/* I2C Registers */
> +#define I2CTIMCTRL      0x0540  /* I2C IF Timing and Enable Control */
> +#define I2CMADDR        0x0544  /* I2C Master Addressing */
> +#define WDATAQ          0x0548  /* Write Data Queue */
> +#define RDATAQ          0x054C  /* Read Data Queue */
> +
> +/* Chip ID and Revision ID Register */
> +#define IDREG           0x0580
> +
> +#define LPX_PERIOD		4
> +#define TTA_GET			0x40000
> +#define TTA_SURE		6
> +
> +#define TC358775XBG_ID  0x00007500
> +
> +/* Debug Registers */
> +#define DEBUG00         0x05A0  /* Debug */
> +#define DEBUG01         0x05A4  /* LVDS Data */
> +
> +#define DSI_CLEN_BIT		BIT(0)
> +#define DIVIDE_BY_3		3 /* PCLK=DCLK/3 */
> +#define LVCFG_LVEN_BIT		BIT(0)
> +
> +#define L0EN BIT(1)
> +
> +
> +#define TC358775_VPCTRL_VSDELAY__MASK	0x3FF00000
> +#define TC358775_VPCTRL_VSDELAY__SHIFT	20
> +static inline u32 TC358775_VPCTRL_VSDELAY(uint32_t val)
> +{
> +	return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) &
> +			TC358775_VPCTRL_VSDELAY__MASK;
> +}
> +
> +#define TC358775_VPCTRL_OPXLFMT__MASK	0x00000100
> +#define TC358775_VPCTRL_OPXLFMT__SHIFT	8
> +static inline u32 TC358775_VPCTRL_OPXLFMT(uint32_t val)
> +{
> +	return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) &
> +			TC358775_VPCTRL_OPXLFMT__MASK;
> +}
> +
> +#define TC358775_VPCTRL_MSF__MASK	0x00000001
> +#define TC358775_VPCTRL_MSF__SHIFT	0
> +static inline u32 TC358775_VPCTRL_MSF(uint32_t val)
> +{
> +	return ((val) << TC358775_VPCTRL_MSF__SHIFT) &
> +			TC358775_VPCTRL_MSF__MASK;
> +}
> +
> +#define TC358775_LVCFG_PCLKDIV__MASK	0x000000f0
> +#define TC358775_LVCFG_PCLKDIV__SHIFT	4
> +static inline u32 TC358775_LVCFG_PCLKDIV(uint32_t val)
> +{
> +	return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) &
> +			TC358775_LVCFG_PCLKDIV__MASK;
> +}
> +
> +#define TC358775_LVCFG_LVDLINK__MASK                         0x00000002
> +#define TC358775_LVCFG_LVDLINK__SHIFT                        0
> +static inline u32 TC358775_LVCFG_LVDLINK(uint32_t val)
> +{
> +	return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) &
> +			TC358775_LVCFG_LVDLINK__MASK;
> +}
> +
> +static const char * const regulator_names[] = {
> +	"vdd",
> +	"vddio"
> +};
> +
> +struct tc_data {
> +	struct i2c_client	*i2c;
> +
> +	struct device		*dev;
> +	struct regmap		*regmap;
> +
> +	struct drm_bridge	bridge;
> +	struct drm_connector	connector;
> +	struct drm_panel	*panel;
> +
> +	enum drm_connector_status status;


As I commented this field is unused, writing to it once, does not make
it 'used'.


> +	struct device_node *host_node;
> +	struct mipi_dsi_device *dsi;
> +	u8 num_dsi_lanes;
> +
> +	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
> +	struct gpio_desc	*reset_gpio;
> +	struct gpio_desc	*stby_gpio;
> +	u32                     rev;


This field is also not needed, you can use local variable instead.


> +	u8                      dual_link; /* single-link or dual-link */
> +};
> +
> +static inline struct tc_data *bridge_to_tc(struct drm_bridge *b)
> +{
> +	return container_of(b, struct tc_data, bridge);
> +}
> +
> +static inline struct tc_data *connector_to_tc(struct drm_connector *c)
> +{
> +	return container_of(c, struct tc_data, connector);
> +}
> +
> +static void tc_bridge_pre_enable(struct drm_bridge *bridge)
> +{
> +	struct tc_data *tc = bridge_to_tc(bridge);
> +	struct device *dev = &tc->dsi->dev;
> +	int ret;
> +
> +	ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies);


Specs says regulator enabling should be ordered with proper delays.


> +	if (ret < 0) {
> +		dev_err(dev, "regulator enable failed, %d\n", ret);
> +		return;
> +	}
> +	usleep_range(10000, 20000);
> +
> +	gpiod_set_value(tc->stby_gpio, 0);
> +	usleep_range(10, 20);
> +
> +	gpiod_set_value(tc->reset_gpio, 0);
> +	usleep_range(10000, 20000);
> +
> +	drm_panel_prepare(tc->panel);
> +}
> +
> +static void tc_bridge_disable(struct drm_bridge *bridge)
> +{
> +	struct tc_data *tc = bridge_to_tc(bridge);
> +	struct device *dev = &tc->dsi->dev;
> +	int ret;
> +
> +	ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies);


Disabling regulators here does not make sense, and is against specs you
pointed in earlier email, see chapter 8.4.5.

In bridge disable you should only stop data transmission, power-off
sequence should be moved to post-disable and reordered according to docs.


> +	if (ret < 0)
> +		dev_err(dev, "regulator disable failed, %d\n", ret);
> +	usleep_range(30000, 40000);
> +
> +	drm_panel_disable(tc->panel);
> +}
> +
> +static void tc_bridge_post_disable(struct drm_bridge *bridge)
> +{
> +	struct tc_data *tc = bridge_to_tc(bridge);
> +
> +	gpiod_set_value(tc->stby_gpio, 1);
> +	usleep_range(10, 20);
> +
> +	gpiod_set_value(tc->reset_gpio, 1);
> +	usleep_range(10000, 20000);
> +
> +	drm_panel_unprepare(tc->panel);
> +}
> +
> +static int d2l_write(struct tc_data *tc, u16 reg, u32 data)
> +{
> +	int ret = 0;
> +
> +	ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1);
> +
> +	return ret;
> +}
> +
> +static void tc_bridge_enable(struct drm_bridge *bridge)
> +{
> +	struct tc_data *tc = bridge_to_tc(bridge);
> +	int ret;
> +	u32 hbpr, hpw, htime1, hfpr, hsize, htime2;
> +	u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2;
> +	u32 val = 0;
> +	u16 bus_formats;
> +	struct drm_display_mode *mode;
> +
> +	mode = &bridge->encoder->crtc->state->adjusted_mode;
> +
> +	hbpr = 0;
> +	hpw  = mode->hsync_end - mode->hsync_start;
> +	vbpr = 0;
> +	vpw  = mode->vsync_end - mode->vsync_start;
> +
> +	htime1 = (hbpr << 16) + hpw;
> +	vtime1 = (vbpr << 16) + vpw;
> +
> +	hfpr = mode->hsync_start - mode->hdisplay;
> +	hsize = mode->hdisplay;
> +	vfpr = mode->vsync_start - mode->vdisplay;
> +	vsize = mode->vdisplay;
> +
> +	htime2 = (hfpr << 16) + hsize;
> +	vtime2 = (vfpr << 16) + vsize;
> +
> +	ret = regmap_read(tc->regmap, IDREG, &tc->rev);
> +	if (ret) {
> +		dev_err(tc->dev, "can not read device ID: %d\n", ret);
> +		return;
> +	}
> +	dev_info(tc->dev, "DSI2LVDS Chip ID.%02x Revision ID. %02x\n",
> +			(tc->rev>>8)&0xFF, (tc->rev)&0xFF);
> +
> +	d2l_write(tc, SYSRST, 0x000000FF);
> +	usleep_range(30000, 40000);
> +
> +	d2l_write(tc, PPI_TX_RX_TA, TTA_GET | TTA_SURE);
> +	d2l_write(tc, PPI_LPTXTIMECNT, LPX_PERIOD);
> +	d2l_write(tc, PPI_D0S_CLRSIPOCOUNT, 3);
> +	d2l_write(tc, PPI_D1S_CLRSIPOCOUNT, 3);
> +	d2l_write(tc, PPI_D2S_CLRSIPOCOUNT, 3);
> +	d2l_write(tc, PPI_D3S_CLRSIPOCOUNT, 3);
> +
> +	val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT;
> +	d2l_write(tc, PPI_LANEENABLE, val);
> +	d2l_write(tc, DSI_LANEENABLE, val);
> +
> +	d2l_write(tc, PPI_STARTPPI, 0x00000001);
> +	d2l_write(tc, DSI_STARTDSI, 0x00000001);
> +
> +	val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value
> +
> +	bus_formats = tc->connector.display_info.bus_formats[0];
> +
> +	if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG
> +		|| bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA) {
> +		/* RGB888 */
> +		val |= TC358775_VPCTRL_OPXLFMT(1);
> +		d2l_write(tc, VPCTRL, val);
> +	} else {
> +		/* RGB666 */
> +		val |= TC358775_VPCTRL_MSF(1);
> +		d2l_write(tc, VPCTRL, val);
> +	}
> +
> +	d2l_write(tc, HTIM1, htime1);
> +	d2l_write(tc, VTIM1, vtime1);
> +	d2l_write(tc, HTIM2, htime2);
> +	d2l_write(tc, VTIM2, vtime2);
> +
> +	d2l_write(tc, VFUEN, 0x00000001);
> +	d2l_write(tc, SYSRST, 0x00000004);
> +	d2l_write(tc, LVPHY0, 0x00040006);
> +
> +	/* default jeida-24 */
> +	if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG) {
> +		/* vesa-24, TODO jeida-18*/
> +		d2l_write(tc, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3));
> +		d2l_write(tc, LV_MX0407, LV_MX(LVI_R4, LVI_R7, LVI_R5, LVI_G0));
> +		d2l_write(tc, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_G6, LVI_G7));
> +		d2l_write(tc, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0));
> +		d2l_write(tc, LV_MX1619, LV_MX(LVI_B6, LVI_B7, LVI_B1, LVI_B2));
> +		d2l_write(tc, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0));
> +		d2l_write(tc, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R6));
> +	}
> +
> +	d2l_write(tc, VFUEN, 0x00000001);
> +
> +	val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT;
> +	if (tc->dual_link)
> +		val |= TC358775_LVCFG_LVDLINK(1);
> +
> +	d2l_write(tc, LVCFG, val);
> +
> +	drm_panel_enable(tc->panel);
> +}
> +
> +static int tc_connector_get_modes(struct drm_connector *connector)
> +{
> +	struct tc_data *tc = connector_to_tc(connector);
> +	struct edid *edid;
> +	unsigned int count;
> +
> +	if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) {
> +		count = tc->panel->funcs->get_modes(tc->panel, connector);
> +		if (count > 0)
> +			return count;
> +	}
> +
> +	edid = drm_get_edid(connector, tc->i2c->adapter);
> +	if (!edid)
> +		return 0;
> +
> +	drm_connector_update_edid_property(connector, edid);
> +	count = drm_add_edid_modes(connector, edid);
> +	kfree(edid);
> +
> +	return count;
> +}
> +
> +static int tc_connector_mode_valid(struct drm_connector *connector,
> +				   struct drm_display_mode *mode)
> +{
> +	struct tc_data *tc = connector_to_tc(connector);
> +
> +	/* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */
> +	if ((mode->clock > 135000 && tc->dual_link == 0) ||
> +	    (mode->clock > 270000 && tc->dual_link == 1))
> +		return MODE_CLOCK_HIGH;
> +
> +	return MODE_OK;
> +}


As Laurent pointed out earlier this should be bridge.mode_valid.


Regards

Andrzej



> +
> +static struct drm_encoder *
> +tc_connector_best_encoder(struct drm_connector *connector)
> +{
> +	struct tc_data *tc = connector_to_tc(connector);
> +
> +	return tc->bridge.encoder;
> +}
> +
> +static const struct drm_connector_helper_funcs tc_connector_helper_funcs = {
> +	.get_modes = tc_connector_get_modes,
> +	.mode_valid = tc_connector_mode_valid,
> +	.best_encoder = tc_connector_best_encoder,
> +};
> +
> +static const struct drm_connector_funcs tc_connector_funcs = {
> +	.fill_modes = drm_helper_probe_single_connector_modes,
> +	.destroy = drm_connector_cleanup,
> +	.reset = drm_atomic_helper_connector_reset,
> +	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> +	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +int tc358775_parse_dt(struct device_node *np, struct tc_data *tc)
> +{
> +	u32 num_lanes;
> +	u8 dual_link;
> +
> +	of_property_read_u8(np, "tc,dual-link", &dual_link);
> +	of_property_read_u32(np, "tc,dsi-lanes", &num_lanes);
> +
> +	if (num_lanes < 1 || num_lanes > 4)
> +		return -EINVAL;
> +
> +	tc->num_dsi_lanes = num_lanes;
> +	tc->dual_link = dual_link;
> +
> +	tc->host_node = of_graph_get_remote_node(np, 0, 0);
> +	if (!tc->host_node)
> +		return -ENODEV;
> +
> +	of_node_put(tc->host_node);
> +
> +	return 0;
> +}
> +
> +int tc358775_attach_dsi(struct tc_data *tc)
> +{
> +	struct device *dev = &tc->i2c->dev;
> +	struct mipi_dsi_host *host;
> +	struct mipi_dsi_device *dsi;
> +	int ret = 0;
> +	const struct mipi_dsi_device_info info = { .type = "tc358775",
> +							.channel = 0,
> +							.node = NULL,
> +						};
> +
> +	host = of_find_mipi_dsi_host_by_node(tc->host_node);
> +	if (!host) {
> +		dev_err(dev, "failed to find dsi host\n");
> +		return -EPROBE_DEFER;
> +	}
> +
> +	dsi = mipi_dsi_device_register_full(host, &info);
> +	if (IS_ERR(dsi)) {
> +		dev_err(dev, "failed to create dsi device\n");
> +		ret = PTR_ERR(dsi);
> +		goto err_dsi_device;
> +	}
> +
> +	tc->dsi = dsi;
> +
> +	dsi->lanes = tc->num_dsi_lanes;
> +	dsi->format = MIPI_DSI_FMT_RGB888;
> +	dsi->mode_flags = MIPI_DSI_MODE_VIDEO;
> +
> +	ret = mipi_dsi_attach(dsi);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to attach dsi to host\n");
> +		goto err_dsi_attach;
> +	}
> +
> +	return 0;
> +
> +err_dsi_attach:
> +	mipi_dsi_device_unregister(dsi);
> +err_dsi_device:
> +	return ret;
> +}
> +
> +static int tc_bridge_attach(struct drm_bridge *bridge)
> +{
> +	struct tc_data *tc = bridge_to_tc(bridge);
> +	struct drm_device *drm = bridge->dev;
> +	int ret;
> +
> +	/* Create LVDS connector */
> +	drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs);
> +	ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs,
> +				 DRM_MODE_CONNECTOR_LVDS);
> +	if (ret)
> +		return ret;
> +
> +	if (tc->panel)
> +		drm_panel_attach(tc->panel, &tc->connector);
> +
> +	drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder);
> +
> +	ret = tc358775_attach_dsi(tc);
> +
> +	return ret;
> +}
> +
> +static const struct drm_bridge_funcs tc_bridge_funcs = {
> +	.attach = tc_bridge_attach,
> +	.pre_enable = tc_bridge_pre_enable,
> +	.enable = tc_bridge_enable,
> +	.disable = tc_bridge_disable,
> +	.post_disable = tc_bridge_post_disable,
> +};
> +
> +static const struct regmap_config tc_regmap_config = {
> +	.name = "tc358775",
> +	.reg_bits = 16,
> +	.val_bits = 32,
> +	.reg_stride = 4,
> +	.max_register = 0x05A8,
> +	.cache_type = REGCACHE_RBTREE,
> +	.reg_format_endian = REGMAP_ENDIAN_BIG,
> +	.val_format_endian = REGMAP_ENDIAN_LITTLE,
> +};
> +
> +static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
> +{
> +	struct device *dev = &client->dev;
> +	struct tc_data *tc;
> +	int ret;
> +	unsigned int i;
> +
> +	tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL);
> +	if (!tc)
> +		return -ENOMEM;
> +
> +	tc->dev = dev;
> +	tc->i2c = client;
> +	tc->status = connector_status_connected;
> +
> +	/* port@1 is the output port */
> +	ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL);
> +	if (ret && ret != -ENODEV)
> +		return ret;
> +
> +	ret = tc358775_parse_dt(dev->of_node, tc);
> +	if (ret)
> +		return ret;
> +
> +	for (i = 0; i < ARRAY_SIZE(tc->supplies); i++)
> +		tc->supplies[i].supply = regulator_names[i];
> +
> +	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies),
> +				      tc->supplies);
> +	if (ret < 0)
> +		dev_err(dev, "failed to init regulator, ret=%d\n", ret);
> +
> +	tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH);
> +	if (IS_ERR(tc->stby_gpio)) {
> +		ret = PTR_ERR(tc->stby_gpio);
> +		dev_err(dev, "cannot get stby-gpio %d\n", ret);
> +		return ret;
> +	}
> +
> +	tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> +	if (IS_ERR(tc->reset_gpio)) {
> +		ret = PTR_ERR(tc->reset_gpio);
> +		dev_err(dev, "cannot get reset-gpios %d\n", ret);
> +		return ret;
> +	}
> +
> +	tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config);
> +	if (IS_ERR(tc->regmap)) {
> +		ret = PTR_ERR(tc->regmap);
> +		dev_err(dev, "Failed to initialize regmap: %d\n", ret);
> +		return ret;
> +	}
> +
> +	tc->bridge.funcs = &tc_bridge_funcs;
> +	tc->bridge.of_node = dev->of_node;
> +	drm_bridge_add(&tc->bridge);
> +
> +	i2c_set_clientdata(client, tc);
> +
> +	return 0;
> +}
> +
> +static int tc_remove(struct i2c_client *client)
> +{
> +	struct tc_data *tc = i2c_get_clientdata(client);
> +
> +	drm_bridge_remove(&tc->bridge);
> +
> +	return 0;
> +}
> +
> +static const struct i2c_device_id tc358775_i2c_ids[] = {
> +	{ "tc358775", 0 },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids);
> +
> +static const struct of_device_id tc358775_of_ids[] = {
> +	{ .compatible = "toshiba,tc358775", },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, tc358775_of_ids);
> +
> +static struct i2c_driver tc358775_driver = {
> +	.driver = {
> +		.name = "tc358775",
> +		.of_match_table = tc358775_of_ids,
> +	},
> +	.id_table = tc358775_i2c_ids,
> +	.probe = tc_probe,
> +	.remove	= tc_remove,
> +};
> +module_i2c_driver(tc358775_driver);
> +
> +MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>");
> +MODULE_DESCRIPTION("tc358775 LVDS encoder driver");


Please fix the description, for example: TC... DSI/LVDS bridge driver


Regards

Andrzej


> +MODULE_LICENSE("GPL v2");
diff mbox series

Patch

diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index 8397bf7..d5528fa 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -133,6 +133,16 @@  config DRM_TOSHIBA_TC358767
 	---help---
 	  Toshiba TC358767 eDP bridge chip driver.
 
+config DRM_TOSHIBA_TC358775
+        tristate "Toshiba TC358775 LVDS bridge"
+        depends on OF
+        select DRM_KMS_HELPER
+        select REGMAP_I2C
+        select DRM_PANEL
+	select DRM_MIPI_DSI
+        ---help---
+          Toshiba TC358775 LVDS bridge chip driver.
+
 config DRM_TI_TFP410
 	tristate "TI TFP410 DVI/HDMI bridge"
 	depends on OF
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 1eb5376..9b2c512 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -12,6 +12,7 @@  obj-$(CONFIG_DRM_SII9234) += sii9234.o
 obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
 obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
 obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
+obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o
 obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
 obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
 obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c
new file mode 100644
index 0000000..28b828e
--- /dev/null
+++ b/drivers/gpu/drm/bridge/tc358775.c
@@ -0,0 +1,688 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * tc358775 DSI to LVDS bridge driver
+ *
+ * Copyright (C) 2020 InforceComputing
+ * Author: Vinay Simha BN <vinaysimha@inforcecomputing.com>
+ *
+ */
+#define DEBUG
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_dp_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_of.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_probe_helper.h>
+
+#define FLD_MASK(start, end)    (((1 << ((start) - (end) + 1)) - 1) << (end))
+#define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end))
+
+/* Registers */
+
+/* DSI D-PHY Layer Registers */
+#define D0W_DPHYCONTTX  0x0004  /* Data Lane 0 DPHY Tx Control */
+#define CLW_DPHYCONTRX  0x0020  /* Clock Lane DPHY Rx Control */
+#define D0W_DPHYCONTRX  0x0024  /* Data Lane 0 DPHY Rx Control */
+#define D1W_DPHYCONTRX  0x0028  /* Data Lane 1 DPHY Rx Control */
+#define D2W_DPHYCONTRX  0x002C  /* Data Lane 2 DPHY Rx Control */
+#define D3W_DPHYCONTRX  0x0030  /* Data Lane 3 DPHY Rx Control */
+#define COM_DPHYCONTRX  0x0038  /* DPHY Rx Common Control */
+#define CLW_CNTRL       0x0040  /* Clock Lane Control */
+#define D0W_CNTRL       0x0044  /* Data Lane 0 Control */
+#define D1W_CNTRL       0x0048  /* Data Lane 1 Control */
+#define D2W_CNTRL       0x004C  /* Data Lane 2 Control */
+#define D3W_CNTRL       0x0050  /* Data Lane 3 Control */
+#define DFTMODE_CNTRL   0x0054  /* DFT Mode Control */
+
+/* DSI PPI Layer Registers */
+#define PPI_STARTPPI    0x0104  /* START control bit of PPI-TX function. */
+#define PPI_BUSYPPI     0x0108
+#define PPI_LINEINITCNT 0x0110  /* Line Initialization Wait Counter  */
+#define PPI_LPTXTIMECNT 0x0114
+#define PPI_LANEENABLE  0x0134  /* Enables each lane at the PPI layer. */
+#define PPI_TX_RX_TA    0x013C  /* DSI Bus Turn Around timing parameters */
+
+/* Analog timer function enable */
+#define PPI_CLS_ATMR    0x0140  /* Delay for Clock Lane in LPRX  */
+#define PPI_D0S_ATMR    0x0144  /* Delay for Data Lane 0 in LPRX */
+#define PPI_D1S_ATMR    0x0148  /* Delay for Data Lane 1 in LPRX */
+#define PPI_D2S_ATMR    0x014C  /* Delay for Data Lane 2 in LPRX */
+#define PPI_D3S_ATMR    0x0150  /* Delay for Data Lane 3 in LPRX */
+
+#define PPI_D0S_CLRSIPOCOUNT    0x0164  /* For lane 0 */
+#define PPI_D1S_CLRSIPOCOUNT    0x0168  /* For lane 1 */
+#define PPI_D2S_CLRSIPOCOUNT    0x016C  /* For lane 2 */
+#define PPI_D3S_CLRSIPOCOUNT    0x0170  /* For lane 3 */
+
+#define CLS_PRE         0x0180  /* Digital Counter inside of PHY IO */
+#define D0S_PRE         0x0184  /* Digital Counter inside of PHY IO */
+#define D1S_PRE         0x0188  /* Digital Counter inside of PHY IO */
+#define D2S_PRE         0x018C  /* Digital Counter inside of PHY IO */
+#define D3S_PRE         0x0190  /* Digital Counter inside of PHY IO */
+#define CLS_PREP        0x01A0  /* Digital Counter inside of PHY IO */
+#define D0S_PREP        0x01A4  /* Digital Counter inside of PHY IO */
+#define D1S_PREP        0x01A8  /* Digital Counter inside of PHY IO */
+#define D2S_PREP        0x01AC  /* Digital Counter inside of PHY IO */
+#define D3S_PREP        0x01B0  /* Digital Counter inside of PHY IO */
+#define CLS_ZERO        0x01C0  /* Digital Counter inside of PHY IO */
+#define D0S_ZERO        0x01C4  /* Digital Counter inside of PHY IO */
+#define D1S_ZERO        0x01C8  /* Digital Counter inside of PHY IO */
+#define D2S_ZERO        0x01CC  /* Digital Counter inside of PHY IO */
+#define D3S_ZERO        0x01D0  /* Digital Counter inside of PHY IO */
+
+#define PPI_CLRFLG      0x01E0  /* PRE Counters has reached set values */
+#define PPI_CLRSIPO     0x01E4  /* Clear SIPO values, Slave mode use only. */
+#define HSTIMEOUT       0x01F0  /* HS Rx Time Out Counter */
+#define HSTIMEOUTENABLE 0x01F4  /* Enable HS Rx Time Out Counter */
+#define DSI_STARTDSI    0x0204  /* START control bit of DSI-TX function */
+#define DSI_BUSYDSI     0x0208
+#define DSI_LANEENABLE  0x0210  /* Enables each lane at the Protocol layer. */
+#define DSI_LANESTATUS0 0x0214  /* Displays lane is in HS RX mode. */
+#define DSI_LANESTATUS1 0x0218  /* Displays lane is in ULPS or STOP state */
+
+#define DSI_INTSTATUS   0x0220  /* Interrupt Status */
+#define DSI_INTMASK     0x0224  /* Interrupt Mask */
+#define DSI_INTCLR      0x0228  /* Interrupt Clear */
+#define DSI_LPTXTO      0x0230  /* Low Power Tx Time Out Counter */
+
+#define DSIERRCNT       0x0300  /* DSI Error Count */
+#define APLCTRL         0x0400  /* Application Layer Control */
+#define RDPKTLN         0x0404  /* Command Read Packet Length */
+
+#define VPCTRL          0x0450  /* Video Path Control */
+#define HTIM1           0x0454  /* Horizontal Timing Control 1 */
+#define HTIM2           0x0458  /* Horizontal Timing Control 2 */
+#define VTIM1           0x045C  /* Vertical Timing Control 1 */
+#define VTIM2           0x0460  /* Vertical Timing Control 2 */
+#define VFUEN           0x0464  /* Video Frame Timing Update Enable */
+
+/* Mux Input Select for LVDS LINK Input */
+#define LV_MX0003        0x0480  /* Bit 0 to 3 */
+#define LV_MX0407        0x0484  /* Bit 4 to 7 */
+#define LV_MX0811        0x0488  /* Bit 8 to 11 */
+#define LV_MX1215        0x048C  /* Bit 12 to 15 */
+#define LV_MX1619        0x0490  /* Bit 16 to 19 */
+#define LV_MX2023        0x0494  /* Bit 20 to 23 */
+#define LV_MX2427        0x0498  /* Bit 24 to 27 */
+#define LV_MX(b0, b1, b2, b3)	(FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \
+				FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24))
+
+/* Input bit numbers used in mux registers */
+enum {
+	LVI_R0,
+	LVI_R1,
+	LVI_R2,
+	LVI_R3,
+	LVI_R4,
+	LVI_R5,
+	LVI_R6,
+	LVI_R7,
+	LVI_G0,
+	LVI_G1,
+	LVI_G2,
+	LVI_G3,
+	LVI_G4,
+	LVI_G5,
+	LVI_G6,
+	LVI_G7,
+	LVI_B0,
+	LVI_B1,
+	LVI_B2,
+	LVI_B3,
+	LVI_B4,
+	LVI_B5,
+	LVI_B6,
+	LVI_B7,
+	LVI_HS,
+	LVI_VS,
+	LVI_DE,
+	LVI_L0
+};
+
+#define LVCFG           0x049C  /* LVDS Configuration  */
+#define LVPHY0          0x04A0  /* LVDS PHY 0 */
+#define LVPHY1          0x04A4  /* LVDS PHY 1 */
+#define SYSSTAT         0x0500  /* System Status  */
+#define SYSRST          0x0504  /* System Reset  */
+/* GPIO Registers */
+#define GPIOC           0x0520  /* GPIO Control  */
+#define GPIOO           0x0524  /* GPIO Output  */
+#define GPIOI           0x0528  /* GPIO Input  */
+
+/* I2C Registers */
+#define I2CTIMCTRL      0x0540  /* I2C IF Timing and Enable Control */
+#define I2CMADDR        0x0544  /* I2C Master Addressing */
+#define WDATAQ          0x0548  /* Write Data Queue */
+#define RDATAQ          0x054C  /* Read Data Queue */
+
+/* Chip ID and Revision ID Register */
+#define IDREG           0x0580
+
+#define LPX_PERIOD		4
+#define TTA_GET			0x40000
+#define TTA_SURE		6
+
+#define TC358775XBG_ID  0x00007500
+
+/* Debug Registers */
+#define DEBUG00         0x05A0  /* Debug */
+#define DEBUG01         0x05A4  /* LVDS Data */
+
+#define DSI_CLEN_BIT		BIT(0)
+#define DIVIDE_BY_3		3 /* PCLK=DCLK/3 */
+#define LVCFG_LVEN_BIT		BIT(0)
+
+#define L0EN BIT(1)
+
+
+#define TC358775_VPCTRL_VSDELAY__MASK	0x3FF00000
+#define TC358775_VPCTRL_VSDELAY__SHIFT	20
+static inline u32 TC358775_VPCTRL_VSDELAY(uint32_t val)
+{
+	return ((val) << TC358775_VPCTRL_VSDELAY__SHIFT) &
+			TC358775_VPCTRL_VSDELAY__MASK;
+}
+
+#define TC358775_VPCTRL_OPXLFMT__MASK	0x00000100
+#define TC358775_VPCTRL_OPXLFMT__SHIFT	8
+static inline u32 TC358775_VPCTRL_OPXLFMT(uint32_t val)
+{
+	return ((val) << TC358775_VPCTRL_OPXLFMT__SHIFT) &
+			TC358775_VPCTRL_OPXLFMT__MASK;
+}
+
+#define TC358775_VPCTRL_MSF__MASK	0x00000001
+#define TC358775_VPCTRL_MSF__SHIFT	0
+static inline u32 TC358775_VPCTRL_MSF(uint32_t val)
+{
+	return ((val) << TC358775_VPCTRL_MSF__SHIFT) &
+			TC358775_VPCTRL_MSF__MASK;
+}
+
+#define TC358775_LVCFG_PCLKDIV__MASK	0x000000f0
+#define TC358775_LVCFG_PCLKDIV__SHIFT	4
+static inline u32 TC358775_LVCFG_PCLKDIV(uint32_t val)
+{
+	return ((val) << TC358775_LVCFG_PCLKDIV__SHIFT) &
+			TC358775_LVCFG_PCLKDIV__MASK;
+}
+
+#define TC358775_LVCFG_LVDLINK__MASK                         0x00000002
+#define TC358775_LVCFG_LVDLINK__SHIFT                        0
+static inline u32 TC358775_LVCFG_LVDLINK(uint32_t val)
+{
+	return ((val) << TC358775_LVCFG_LVDLINK__SHIFT) &
+			TC358775_LVCFG_LVDLINK__MASK;
+}
+
+static const char * const regulator_names[] = {
+	"vdd",
+	"vddio"
+};
+
+struct tc_data {
+	struct i2c_client	*i2c;
+
+	struct device		*dev;
+	struct regmap		*regmap;
+
+	struct drm_bridge	bridge;
+	struct drm_connector	connector;
+	struct drm_panel	*panel;
+
+	enum drm_connector_status status;
+	struct device_node *host_node;
+	struct mipi_dsi_device *dsi;
+	u8 num_dsi_lanes;
+
+	struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)];
+	struct gpio_desc	*reset_gpio;
+	struct gpio_desc	*stby_gpio;
+	u32                     rev;
+	u8                      dual_link; /* single-link or dual-link */
+};
+
+static inline struct tc_data *bridge_to_tc(struct drm_bridge *b)
+{
+	return container_of(b, struct tc_data, bridge);
+}
+
+static inline struct tc_data *connector_to_tc(struct drm_connector *c)
+{
+	return container_of(c, struct tc_data, connector);
+}
+
+static void tc_bridge_pre_enable(struct drm_bridge *bridge)
+{
+	struct tc_data *tc = bridge_to_tc(bridge);
+	struct device *dev = &tc->dsi->dev;
+	int ret;
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(tc->supplies), tc->supplies);
+	if (ret < 0) {
+		dev_err(dev, "regulator enable failed, %d\n", ret);
+		return;
+	}
+	usleep_range(10000, 20000);
+
+	gpiod_set_value(tc->stby_gpio, 0);
+	usleep_range(10, 20);
+
+	gpiod_set_value(tc->reset_gpio, 0);
+	usleep_range(10000, 20000);
+
+	drm_panel_prepare(tc->panel);
+}
+
+static void tc_bridge_disable(struct drm_bridge *bridge)
+{
+	struct tc_data *tc = bridge_to_tc(bridge);
+	struct device *dev = &tc->dsi->dev;
+	int ret;
+
+	ret = regulator_bulk_disable(ARRAY_SIZE(tc->supplies), tc->supplies);
+	if (ret < 0)
+		dev_err(dev, "regulator disable failed, %d\n", ret);
+	usleep_range(30000, 40000);
+
+	drm_panel_disable(tc->panel);
+}
+
+static void tc_bridge_post_disable(struct drm_bridge *bridge)
+{
+	struct tc_data *tc = bridge_to_tc(bridge);
+
+	gpiod_set_value(tc->stby_gpio, 1);
+	usleep_range(10, 20);
+
+	gpiod_set_value(tc->reset_gpio, 1);
+	usleep_range(10000, 20000);
+
+	drm_panel_unprepare(tc->panel);
+}
+
+static int d2l_write(struct tc_data *tc, u16 reg, u32 data)
+{
+	int ret = 0;
+
+	ret = regmap_bulk_write(tc->regmap, reg, (u32[]) {data}, 1);
+
+	return ret;
+}
+
+static void tc_bridge_enable(struct drm_bridge *bridge)
+{
+	struct tc_data *tc = bridge_to_tc(bridge);
+	int ret;
+	u32 hbpr, hpw, htime1, hfpr, hsize, htime2;
+	u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2;
+	u32 val = 0;
+	u16 bus_formats;
+	struct drm_display_mode *mode;
+
+	mode = &bridge->encoder->crtc->state->adjusted_mode;
+
+	hbpr = 0;
+	hpw  = mode->hsync_end - mode->hsync_start;
+	vbpr = 0;
+	vpw  = mode->vsync_end - mode->vsync_start;
+
+	htime1 = (hbpr << 16) + hpw;
+	vtime1 = (vbpr << 16) + vpw;
+
+	hfpr = mode->hsync_start - mode->hdisplay;
+	hsize = mode->hdisplay;
+	vfpr = mode->vsync_start - mode->vdisplay;
+	vsize = mode->vdisplay;
+
+	htime2 = (hfpr << 16) + hsize;
+	vtime2 = (vfpr << 16) + vsize;
+
+	ret = regmap_read(tc->regmap, IDREG, &tc->rev);
+	if (ret) {
+		dev_err(tc->dev, "can not read device ID: %d\n", ret);
+		return;
+	}
+	dev_info(tc->dev, "DSI2LVDS Chip ID.%02x Revision ID. %02x\n",
+			(tc->rev>>8)&0xFF, (tc->rev)&0xFF);
+
+	d2l_write(tc, SYSRST, 0x000000FF);
+	usleep_range(30000, 40000);
+
+	d2l_write(tc, PPI_TX_RX_TA, TTA_GET | TTA_SURE);
+	d2l_write(tc, PPI_LPTXTIMECNT, LPX_PERIOD);
+	d2l_write(tc, PPI_D0S_CLRSIPOCOUNT, 3);
+	d2l_write(tc, PPI_D1S_CLRSIPOCOUNT, 3);
+	d2l_write(tc, PPI_D2S_CLRSIPOCOUNT, 3);
+	d2l_write(tc, PPI_D3S_CLRSIPOCOUNT, 3);
+
+	val = ((L0EN << tc->num_dsi_lanes) - L0EN) | DSI_CLEN_BIT;
+	d2l_write(tc, PPI_LANEENABLE, val);
+	d2l_write(tc, DSI_LANEENABLE, val);
+
+	d2l_write(tc, PPI_STARTPPI, 0x00000001);
+	d2l_write(tc, DSI_STARTDSI, 0x00000001);
+
+	val = TC358775_VPCTRL_VSDELAY(21); //TODO : to set the dynamic value
+
+	bus_formats = tc->connector.display_info.bus_formats[0];
+
+	if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG
+		|| bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA) {
+		/* RGB888 */
+		val |= TC358775_VPCTRL_OPXLFMT(1);
+		d2l_write(tc, VPCTRL, val);
+	} else {
+		/* RGB666 */
+		val |= TC358775_VPCTRL_MSF(1);
+		d2l_write(tc, VPCTRL, val);
+	}
+
+	d2l_write(tc, HTIM1, htime1);
+	d2l_write(tc, VTIM1, vtime1);
+	d2l_write(tc, HTIM2, htime2);
+	d2l_write(tc, VTIM2, vtime2);
+
+	d2l_write(tc, VFUEN, 0x00000001);
+	d2l_write(tc, SYSRST, 0x00000004);
+	d2l_write(tc, LVPHY0, 0x00040006);
+
+	/* default jeida-24 */
+	if (bus_formats == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG) {
+		/* vesa-24, TODO jeida-18*/
+		d2l_write(tc, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3));
+		d2l_write(tc, LV_MX0407, LV_MX(LVI_R4, LVI_R7, LVI_R5, LVI_G0));
+		d2l_write(tc, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_G6, LVI_G7));
+		d2l_write(tc, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0));
+		d2l_write(tc, LV_MX1619, LV_MX(LVI_B6, LVI_B7, LVI_B1, LVI_B2));
+		d2l_write(tc, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0));
+		d2l_write(tc, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R6));
+	}
+
+	d2l_write(tc, VFUEN, 0x00000001);
+
+	val = TC358775_LVCFG_PCLKDIV(DIVIDE_BY_3) | LVCFG_LVEN_BIT;
+	if (tc->dual_link)
+		val |= TC358775_LVCFG_LVDLINK(1);
+
+	d2l_write(tc, LVCFG, val);
+
+	drm_panel_enable(tc->panel);
+}
+
+static int tc_connector_get_modes(struct drm_connector *connector)
+{
+	struct tc_data *tc = connector_to_tc(connector);
+	struct edid *edid;
+	unsigned int count;
+
+	if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) {
+		count = tc->panel->funcs->get_modes(tc->panel, connector);
+		if (count > 0)
+			return count;
+	}
+
+	edid = drm_get_edid(connector, tc->i2c->adapter);
+	if (!edid)
+		return 0;
+
+	drm_connector_update_edid_property(connector, edid);
+	count = drm_add_edid_modes(connector, edid);
+	kfree(edid);
+
+	return count;
+}
+
+static int tc_connector_mode_valid(struct drm_connector *connector,
+				   struct drm_display_mode *mode)
+{
+	struct tc_data *tc = connector_to_tc(connector);
+
+	/* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */
+	if ((mode->clock > 135000 && tc->dual_link == 0) ||
+	    (mode->clock > 270000 && tc->dual_link == 1))
+		return MODE_CLOCK_HIGH;
+
+	return MODE_OK;
+}
+
+static struct drm_encoder *
+tc_connector_best_encoder(struct drm_connector *connector)
+{
+	struct tc_data *tc = connector_to_tc(connector);
+
+	return tc->bridge.encoder;
+}
+
+static const struct drm_connector_helper_funcs tc_connector_helper_funcs = {
+	.get_modes = tc_connector_get_modes,
+	.mode_valid = tc_connector_mode_valid,
+	.best_encoder = tc_connector_best_encoder,
+};
+
+static const struct drm_connector_funcs tc_connector_funcs = {
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.destroy = drm_connector_cleanup,
+	.reset = drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+int tc358775_parse_dt(struct device_node *np, struct tc_data *tc)
+{
+	u32 num_lanes;
+	u8 dual_link;
+
+	of_property_read_u8(np, "tc,dual-link", &dual_link);
+	of_property_read_u32(np, "tc,dsi-lanes", &num_lanes);
+
+	if (num_lanes < 1 || num_lanes > 4)
+		return -EINVAL;
+
+	tc->num_dsi_lanes = num_lanes;
+	tc->dual_link = dual_link;
+
+	tc->host_node = of_graph_get_remote_node(np, 0, 0);
+	if (!tc->host_node)
+		return -ENODEV;
+
+	of_node_put(tc->host_node);
+
+	return 0;
+}
+
+int tc358775_attach_dsi(struct tc_data *tc)
+{
+	struct device *dev = &tc->i2c->dev;
+	struct mipi_dsi_host *host;
+	struct mipi_dsi_device *dsi;
+	int ret = 0;
+	const struct mipi_dsi_device_info info = { .type = "tc358775",
+							.channel = 0,
+							.node = NULL,
+						};
+
+	host = of_find_mipi_dsi_host_by_node(tc->host_node);
+	if (!host) {
+		dev_err(dev, "failed to find dsi host\n");
+		return -EPROBE_DEFER;
+	}
+
+	dsi = mipi_dsi_device_register_full(host, &info);
+	if (IS_ERR(dsi)) {
+		dev_err(dev, "failed to create dsi device\n");
+		ret = PTR_ERR(dsi);
+		goto err_dsi_device;
+	}
+
+	tc->dsi = dsi;
+
+	dsi->lanes = tc->num_dsi_lanes;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO;
+
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0) {
+		dev_err(dev, "failed to attach dsi to host\n");
+		goto err_dsi_attach;
+	}
+
+	return 0;
+
+err_dsi_attach:
+	mipi_dsi_device_unregister(dsi);
+err_dsi_device:
+	return ret;
+}
+
+static int tc_bridge_attach(struct drm_bridge *bridge)
+{
+	struct tc_data *tc = bridge_to_tc(bridge);
+	struct drm_device *drm = bridge->dev;
+	int ret;
+
+	/* Create LVDS connector */
+	drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs);
+	ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs,
+				 DRM_MODE_CONNECTOR_LVDS);
+	if (ret)
+		return ret;
+
+	if (tc->panel)
+		drm_panel_attach(tc->panel, &tc->connector);
+
+	drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder);
+
+	ret = tc358775_attach_dsi(tc);
+
+	return ret;
+}
+
+static const struct drm_bridge_funcs tc_bridge_funcs = {
+	.attach = tc_bridge_attach,
+	.pre_enable = tc_bridge_pre_enable,
+	.enable = tc_bridge_enable,
+	.disable = tc_bridge_disable,
+	.post_disable = tc_bridge_post_disable,
+};
+
+static const struct regmap_config tc_regmap_config = {
+	.name = "tc358775",
+	.reg_bits = 16,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = 0x05A8,
+	.cache_type = REGCACHE_RBTREE,
+	.reg_format_endian = REGMAP_ENDIAN_BIG,
+	.val_format_endian = REGMAP_ENDIAN_LITTLE,
+};
+
+static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct tc_data *tc;
+	int ret;
+	unsigned int i;
+
+	tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL);
+	if (!tc)
+		return -ENOMEM;
+
+	tc->dev = dev;
+	tc->i2c = client;
+	tc->status = connector_status_connected;
+
+	/* port@1 is the output port */
+	ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &tc->panel, NULL);
+	if (ret && ret != -ENODEV)
+		return ret;
+
+	ret = tc358775_parse_dt(dev->of_node, tc);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < ARRAY_SIZE(tc->supplies); i++)
+		tc->supplies[i].supply = regulator_names[i];
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(tc->supplies),
+				      tc->supplies);
+	if (ret < 0)
+		dev_err(dev, "failed to init regulator, ret=%d\n", ret);
+
+	tc->stby_gpio = devm_gpiod_get(dev, "stby", GPIOD_OUT_HIGH);
+	if (IS_ERR(tc->stby_gpio)) {
+		ret = PTR_ERR(tc->stby_gpio);
+		dev_err(dev, "cannot get stby-gpio %d\n", ret);
+		return ret;
+	}
+
+	tc->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(tc->reset_gpio)) {
+		ret = PTR_ERR(tc->reset_gpio);
+		dev_err(dev, "cannot get reset-gpios %d\n", ret);
+		return ret;
+	}
+
+	tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config);
+	if (IS_ERR(tc->regmap)) {
+		ret = PTR_ERR(tc->regmap);
+		dev_err(dev, "Failed to initialize regmap: %d\n", ret);
+		return ret;
+	}
+
+	tc->bridge.funcs = &tc_bridge_funcs;
+	tc->bridge.of_node = dev->of_node;
+	drm_bridge_add(&tc->bridge);
+
+	i2c_set_clientdata(client, tc);
+
+	return 0;
+}
+
+static int tc_remove(struct i2c_client *client)
+{
+	struct tc_data *tc = i2c_get_clientdata(client);
+
+	drm_bridge_remove(&tc->bridge);
+
+	return 0;
+}
+
+static const struct i2c_device_id tc358775_i2c_ids[] = {
+	{ "tc358775", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, tc358775_i2c_ids);
+
+static const struct of_device_id tc358775_of_ids[] = {
+	{ .compatible = "toshiba,tc358775", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, tc358775_of_ids);
+
+static struct i2c_driver tc358775_driver = {
+	.driver = {
+		.name = "tc358775",
+		.of_match_table = tc358775_of_ids,
+	},
+	.id_table = tc358775_i2c_ids,
+	.probe = tc_probe,
+	.remove	= tc_remove,
+};
+module_i2c_driver(tc358775_driver);
+
+MODULE_AUTHOR("Vinay Simha BN <vinaysimha@inforcecomputing.com>");
+MODULE_DESCRIPTION("tc358775 LVDS encoder driver");
+MODULE_LICENSE("GPL v2");