[PULL,09/15] block: truncate: Don't make backing file data visible
diff mbox series

Message ID 20200430155231.473156-10-kwolf@redhat.com
State New
Headers show
Series
  • [PULL,01/15] qcow2: Add incompatibility note between backing files and raw external data files
Related show

Commit Message

Kevin Wolf April 30, 2020, 3:52 p.m. UTC
When extending the size of an image that has a backing file larger than
its old size, make sure that the backing file data doesn't become
visible in the guest, but the added area is properly zeroed out.

Consider the following scenario where the overlay is shorter than its
backing file:

    base.qcow2:     AAAAAAAA
    overlay.qcow2:  BBBB

When resizing (extending) overlay.qcow2, the new blocks should not stay
unallocated and make the additional As from base.qcow2 visible like
before this patch, but zeros should be read.

A similar case happens with the various variants of a commit job when an
intermediate file is short (- for unallocated):

    base.qcow2:     A-A-AAAA
    mid.qcow2:      BB-B
    top.qcow2:      C--C--C-

After commit top.qcow2 to mid.qcow2, the following happens:

    mid.qcow2:      CB-C00C0 (correct result)
    mid.qcow2:      CB-C--C- (before this fix)

Without the fix, blocks that previously read as zeros on top.qcow2
suddenly turn into A.

Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200424125448.63318-8-kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
---
 block/io.c | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)

Patch
diff mbox series

diff --git a/block/io.c b/block/io.c
index 795075954e..a4f9714230 100644
--- a/block/io.c
+++ b/block/io.c
@@ -3394,6 +3394,31 @@  int coroutine_fn bdrv_co_truncate(BdrvChild *child, int64_t offset, bool exact,
         goto out;
     }
 
+    /*
+     * If the image has a backing file that is large enough that it would
+     * provide data for the new area, we cannot leave it unallocated because
+     * then the backing file content would become visible. Instead, zero-fill
+     * the new area.
+     *
+     * Note that if the image has a backing file, but was opened without the
+     * backing file, taking care of keeping things consistent with that backing
+     * file is the user's responsibility.
+     */
+    if (new_bytes && bs->backing) {
+        int64_t backing_len;
+
+        backing_len = bdrv_getlength(backing_bs(bs));
+        if (backing_len < 0) {
+            ret = backing_len;
+            error_setg_errno(errp, -ret, "Could not get backing file size");
+            goto out;
+        }
+
+        if (backing_len > old_size) {
+            flags |= BDRV_REQ_ZERO_WRITE;
+        }
+    }
+
     if (drv->bdrv_co_truncate) {
         if (flags & ~bs->supported_truncate_flags) {
             error_setg(errp, "Block driver does not support requested flags");