diff mbox series

[v1] dt-bindings: spi: Add schema for Cadence QSPI Controller driver

Message ID 20200512004919.40685-1-vadivel.muruganx.ramuthevar@linux.intel.com (mailing list archive)
State Superseded
Headers show
Series [v1] dt-bindings: spi: Add schema for Cadence QSPI Controller driver | expand

Commit Message

Ramuthevar,Vadivel MuruganX May 12, 2020, 12:49 a.m. UTC
From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>

Add dt-bindings documentation for Cadence-QSPI controller to support
spi based flash memories.

Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
---
 .../devicetree/bindings/mtd/cadence-quadspi.txt    |  67 -----------
 .../devicetree/bindings/spi/cdns,qspi-nor.yaml     | 127 +++++++++++++++++++++
 2 files changed, 127 insertions(+), 67 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
 create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml

Comments

Rob Herring (Arm) May 19, 2020, 6:44 p.m. UTC | #1
On Tue, May 12, 2020 at 08:49:19AM +0800, Ramuthevar,Vadivel MuruganX wrote:
> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> 
> Add dt-bindings documentation for Cadence-QSPI controller to support
> spi based flash memories.
> 
> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> ---
>  .../devicetree/bindings/mtd/cadence-quadspi.txt    |  67 -----------
>  .../devicetree/bindings/spi/cdns,qspi-nor.yaml     | 127 +++++++++++++++++++++
>  2 files changed, 127 insertions(+), 67 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>  create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
> 
> diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
> deleted file mode 100644
> index 945be7d5b236..000000000000
> --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
> +++ /dev/null
> @@ -1,67 +0,0 @@
> -* Cadence Quad SPI controller
> -
> -Required properties:
> -- compatible : should be one of the following:
> -	Generic default - "cdns,qspi-nor".
> -	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> -	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
> -- reg : Contains two entries, each of which is a tuple consisting of a
> -	physical address and length. The first entry is the address and
> -	length of the controller register set. The second entry is the
> -	address and length of the QSPI Controller data area.
> -- interrupts : Unit interrupt specifier for the controller interrupt.
> -- clocks : phandle to the Quad SPI clock.
> -- cdns,fifo-depth : Size of the data FIFO in words.
> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
> -
> -Optional properties:
> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
> -  the read data rather than the QSPI clock. Make sure that QSPI return
> -  clock is populated on the board before using this property.
> -
> -Optional subnodes:
> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
> -custom properties:
> -- cdns,read-delay : Delay for read capture logic, in clock cycles
> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
> -                  mode chip select outputs are de-asserted between
> -		  transactions.
> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
> -                  de-activated and the activation of another.
> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
> -                  transaction and deasserting the device chip select
> -		  (qspi_n_ss_out).
> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
> -                  and first bit transfer.
> -- resets	: Must contain an entry for each entry in reset-names.
> -		  See ../reset/reset.txt for details.
> -- reset-names	: Must include either "qspi" and/or "qspi-ocp".
> -
> -Example:
> -
> -	qspi: spi@ff705000 {
> -		compatible = "cdns,qspi-nor";
> -		#address-cells = <1>;
> -		#size-cells = <0>;
> -		reg = <0xff705000 0x1000>,
> -		      <0xffa00000 0x1000>;
> -		interrupts = <0 151 4>;
> -		clocks = <&qspi_clk>;
> -		cdns,is-decoded-cs;
> -		cdns,fifo-depth = <128>;
> -		cdns,fifo-width = <4>;
> -		cdns,trigger-address = <0x00000000>;
> -		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
> -		reset-names = "qspi", "qspi-ocp";
> -
> -		flash0: n25q00@0 {
> -			...
> -			cdns,read-delay = <4>;
> -			cdns,tshsl-ns = <50>;
> -			cdns,tsd2d-ns = <50>;
> -			cdns,tchsh-ns = <4>;
> -			cdns,tslch-ns = <4>;
> -		};
> -	};
> diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
> new file mode 100644
> index 000000000000..28112b38e6a9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
> @@ -0,0 +1,127 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Cadence QSPI Flash Controller support
> +
> +maintainers:
> +  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> +
> +allOf:
> +  - $ref: "spi-controller.yaml#"
> +
> +description: |
> +  Binding Documentation for Cadence QSPI controller,This controller is
> +  present in the Intel LGM, Altera SoCFPGA and TI SoCs and this driver
> +  has been tested On Intel's LGM SoC.
> +
> +properties:
> +  compatible:
> +     enum:
> +       - cdns,qspi-nor
> +       - ti,k2g-qspi
> +       - ti,am654-ospi
> +       - intel,lgm-qspi
> +
> +  reg:
> +    maxItems: 2

Need to define what each entry is.

> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  cdns,fifo-depth:
> +    description:
> +     Depth of hardware FIFOs.

...FIFO in words.

> +    allOf:
> +      - $ref: "/schemas/types.yaml#/definitions/uint32"
> +      - enum: [ 128, 256 ]
> +      - default: 128
> +
> +  cdns,fifo-width:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      4 byte bus width of the data FIFO in bytes.

Constraints? Perhaps:

multipleOf: 4

if an enum doesn't work here.

> +
> +  cdns,trigger-address:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      32-bit indirect AHB trigger address.
> +
> +  cdns,rclk-en:
> +    type: boolean
> +    description: |
> +      Flag to indicate that QSPI return clock is used to latch the read data
> +      rather than the QSPI clock. Make sure that QSPI return clock is populated
> +      on the board before using this property.
> +
> +# subnode's properties
> +patternProperties:
> +  "^.*@[0-9a-fa-f]+$":

'a-f' is twice. What's the max number of chip selects? If less than 10, 
then '@[0-9]$' is enough. '^.*' can be dropped too.

> +    type: object
> +    description:
> +      flash device uses the subnodes below defined properties.
> +
> +  cdns,read-delay:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Delay for read capture logic, in clock cycles.
> +
> +  cdns,tshsl-ns:
> +    description: |
> +      Delay in nanoseconds for the length that the master mode chip select
> +      outputs are de-asserted between transactions.
> +
> +  cdns,tsd2d-ns:
> +    description: |
> +      Delay in nanoseconds between one chip select being de-activated
> +      and the activation of another.
> +
> +  cdns,tchsh-ns:
> +    description: |
> +      Delay in nanoseconds between last bit of current transaction and
> +      deasserting the device chip select (qspi_n_ss_out).
> +
> +  cdns,tslch-ns:
> +    description: |
> +      Delay in nanoseconds between setting qspi_n_ss_out low and
> +      first bit transfer.
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - cdns,fifo-depth
> +  - cdns,fifo-width
> +  - cdns,trigger-address
> +
> +examples:
> +  - |
> +    spi@ff705000 {
> +          compatible = "cdns,qspi-nor";
> +          #address-cells = <1>;
> +          #size-cells = <0>;
> +          reg = <0xff705000 0x1000>,
> +                <0xffa00000 0x1000>;

Seems kind of small for a data area if this is like most SPI flash 
controllers.

> +          interrupts = <0 151 4>;
> +          clocks = <&qspi_clk>;
> +          cdns,fifo-depth = <128>;
> +          cdns,fifo-width = <4>;
> +          cdns,trigger-address = <0x00000000>;
> +
> +          flash@0 {
> +              compatible = "jedec,spi-nor";
> +              reg = <0x0>;
> +              cdns,read-delay = <4>;
> +              cdns,tshsl-ns = <50>;
> +              cdns,tsd2d-ns = <50>;
> +              cdns,tchsh-ns = <4>;
> +              cdns,tslch-ns = <4>;
> +          };
> +    };
> +
> -- 
> 2.11.0
>
Ramuthevar,Vadivel MuruganX May 20, 2020, 10:05 a.m. UTC | #2
Hi Rob,

   Thank you very much for the review comments...

On 20/5/2020 2:44 am, Rob Herring wrote:
> On Tue, May 12, 2020 at 08:49:19AM +0800, Ramuthevar,Vadivel MuruganX wrote:
>> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>>
>> Add dt-bindings documentation for Cadence-QSPI controller to support
>> spi based flash memories.
>>
>> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>> ---
>>   .../devicetree/bindings/mtd/cadence-quadspi.txt    |  67 -----------
>>   .../devicetree/bindings/spi/cdns,qspi-nor.yaml     | 127 +++++++++++++++++++++
>>   2 files changed, 127 insertions(+), 67 deletions(-)
>>   delete mode 100644 Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>>   create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>> deleted file mode 100644
>> index 945be7d5b236..000000000000
>> --- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
>> +++ /dev/null
>> @@ -1,67 +0,0 @@
>> -* Cadence Quad SPI controller
>> -
>> -Required properties:
>> -- compatible : should be one of the following:
>> -	Generic default - "cdns,qspi-nor".
>> -	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
>> -	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
>> -- reg : Contains two entries, each of which is a tuple consisting of a
>> -	physical address and length. The first entry is the address and
>> -	length of the controller register set. The second entry is the
>> -	address and length of the QSPI Controller data area.
>> -- interrupts : Unit interrupt specifier for the controller interrupt.
>> -- clocks : phandle to the Quad SPI clock.
>> -- cdns,fifo-depth : Size of the data FIFO in words.
>> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
>> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
>> -
>> -Optional properties:
>> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
>> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
>> -  the read data rather than the QSPI clock. Make sure that QSPI return
>> -  clock is populated on the board before using this property.
>> -
>> -Optional subnodes:
>> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
>> -custom properties:
>> -- cdns,read-delay : Delay for read capture logic, in clock cycles
>> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
>> -                  mode chip select outputs are de-asserted between
>> -		  transactions.
>> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
>> -                  de-activated and the activation of another.
>> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
>> -                  transaction and deasserting the device chip select
>> -		  (qspi_n_ss_out).
>> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
>> -                  and first bit transfer.
>> -- resets	: Must contain an entry for each entry in reset-names.
>> -		  See ../reset/reset.txt for details.
>> -- reset-names	: Must include either "qspi" and/or "qspi-ocp".
>> -
>> -Example:
>> -
>> -	qspi: spi@ff705000 {
>> -		compatible = "cdns,qspi-nor";
>> -		#address-cells = <1>;
>> -		#size-cells = <0>;
>> -		reg = <0xff705000 0x1000>,
>> -		      <0xffa00000 0x1000>;
>> -		interrupts = <0 151 4>;
>> -		clocks = <&qspi_clk>;
>> -		cdns,is-decoded-cs;
>> -		cdns,fifo-depth = <128>;
>> -		cdns,fifo-width = <4>;
>> -		cdns,trigger-address = <0x00000000>;
>> -		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
>> -		reset-names = "qspi", "qspi-ocp";
>> -
>> -		flash0: n25q00@0 {
>> -			...
>> -			cdns,read-delay = <4>;
>> -			cdns,tshsl-ns = <50>;
>> -			cdns,tsd2d-ns = <50>;
>> -			cdns,tchsh-ns = <4>;
>> -			cdns,tslch-ns = <4>;
>> -		};
>> -	};
>> diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
>> new file mode 100644
>> index 000000000000..28112b38e6a9
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
>> @@ -0,0 +1,127 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: "http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#"
>> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
>> +
>> +title: Cadence QSPI Flash Controller support
>> +
>> +maintainers:
>> +  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>> +
>> +allOf:
>> +  - $ref: "spi-controller.yaml#"
>> +
>> +description: |
>> +  Binding Documentation for Cadence QSPI controller,This controller is
>> +  present in the Intel LGM, Altera SoCFPGA and TI SoCs and this driver
>> +  has been tested On Intel's LGM SoC.
>> +
>> +properties:
>> +  compatible:
>> +     enum:
>> +       - cdns,qspi-nor
>> +       - ti,k2g-qspi
>> +       - ti,am654-ospi
>> +       - intel,lgm-qspi
>> +
>> +  reg:
>> +    maxItems: 2
> 
> Need to define what each entry is.
Noted.
> 
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  cdns,fifo-depth:
>> +    description:
>> +     Depth of hardware FIFOs.
> 
> ...FIFO in words.
Good catch.
> 
>> +    allOf:
>> +      - $ref: "/schemas/types.yaml#/definitions/uint32"
>> +      - enum: [ 128, 256 ]
>> +      - default: 128
>> +
>> +  cdns,fifo-width:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      4 byte bus width of the data FIFO in bytes.
> 
> Constraints? Perhaps:
> 
> multipleOf: 4
Noted, will update.
> 
> if an enum doesn't work here.
> 
>> +
>> +  cdns,trigger-address:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      32-bit indirect AHB trigger address.
>> +
>> +  cdns,rclk-en:
>> +    type: boolean
>> +    description: |
>> +      Flag to indicate that QSPI return clock is used to latch the read data
>> +      rather than the QSPI clock. Make sure that QSPI return clock is populated
>> +      on the board before using this property.
>> +
>> +# subnode's properties
>> +patternProperties:
>> +  "^.*@[0-9a-fa-f]+$":
> 
> 'a-f' is twice. What's the max number of chip selects? If less than 10,
> then '@[0-9]$' is enough. '^.*' can be dropped too.
16 chip select supports.
> 
>> +    type: object
>> +    description:
>> +      flash device uses the subnodes below defined properties.
>> +
>> +  cdns,read-delay:
>> +    $ref: /schemas/types.yaml#/definitions/uint32
>> +    description:
>> +      Delay for read capture logic, in clock cycles.
>> +
>> +  cdns,tshsl-ns:
>> +    description: |
>> +      Delay in nanoseconds for the length that the master mode chip select
>> +      outputs are de-asserted between transactions.
>> +
>> +  cdns,tsd2d-ns:
>> +    description: |
>> +      Delay in nanoseconds between one chip select being de-activated
>> +      and the activation of another.
>> +
>> +  cdns,tchsh-ns:
>> +    description: |
>> +      Delay in nanoseconds between last bit of current transaction and
>> +      deasserting the device chip select (qspi_n_ss_out).
>> +
>> +  cdns,tslch-ns:
>> +    description: |
>> +      Delay in nanoseconds between setting qspi_n_ss_out low and
>> +      first bit transfer.
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - interrupts
>> +  - clocks
>> +  - cdns,fifo-depth
>> +  - cdns,fifo-width
>> +  - cdns,trigger-address
>> +
>> +examples:
>> +  - |
>> +    spi@ff705000 {
>> +          compatible = "cdns,qspi-nor";
>> +          #address-cells = <1>;
>> +          #size-cells = <0>;
>> +          reg = <0xff705000 0x1000>,
>> +                <0xffa00000 0x1000>;
> 
> Seems kind of small for a data area if this is like most SPI flash
> controllers.yes you are right, following the existing example as it is.

Regards
Vadivel

> 
>> +          interrupts = <0 151 4>;
>> +          clocks = <&qspi_clk>;
>> +          cdns,fifo-depth = <128>;
>> +          cdns,fifo-width = <4>;
>> +          cdns,trigger-address = <0x00000000>;
>> +
>> +          flash@0 {
>> +              compatible = "jedec,spi-nor";
>> +              reg = <0x0>;
>> +              cdns,read-delay = <4>;
>> +              cdns,tshsl-ns = <50>;
>> +              cdns,tsd2d-ns = <50>;
>> +              cdns,tchsh-ns = <4>;
>> +              cdns,tslch-ns = <4>;
>> +          };
>> +    };
>> +
>> -- 
>> 2.11.0
>>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt b/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
deleted file mode 100644
index 945be7d5b236..000000000000
--- a/Documentation/devicetree/bindings/mtd/cadence-quadspi.txt
+++ /dev/null
@@ -1,67 +0,0 @@ 
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
-	Generic default - "cdns,qspi-nor".
-	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
-	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
-	physical address and length. The first entry is the address and
-	length of the controller register set. The second entry is the
-	address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
-  the read data rather than the QSPI clock. Make sure that QSPI return
-  clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
-                  mode chip select outputs are de-asserted between
-		  transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
-                  de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
-                  transaction and deasserting the device chip select
-		  (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
-                  and first bit transfer.
-- resets	: Must contain an entry for each entry in reset-names.
-		  See ../reset/reset.txt for details.
-- reset-names	: Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
-	qspi: spi@ff705000 {
-		compatible = "cdns,qspi-nor";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0xff705000 0x1000>,
-		      <0xffa00000 0x1000>;
-		interrupts = <0 151 4>;
-		clocks = <&qspi_clk>;
-		cdns,is-decoded-cs;
-		cdns,fifo-depth = <128>;
-		cdns,fifo-width = <4>;
-		cdns,trigger-address = <0x00000000>;
-		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
-		reset-names = "qspi", "qspi-ocp";
-
-		flash0: n25q00@0 {
-			...
-			cdns,read-delay = <4>;
-			cdns,tshsl-ns = <50>;
-			cdns,tsd2d-ns = <50>;
-			cdns,tchsh-ns = <4>;
-			cdns,tslch-ns = <4>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
new file mode 100644
index 000000000000..28112b38e6a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml
@@ -0,0 +1,127 @@ 
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/spi/cdns,qspi-nor.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Cadence QSPI Flash Controller support
+
+maintainers:
+  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+description: |
+  Binding Documentation for Cadence QSPI controller,This controller is
+  present in the Intel LGM, Altera SoCFPGA and TI SoCs and this driver
+  has been tested On Intel's LGM SoC.
+
+properties:
+  compatible:
+     enum:
+       - cdns,qspi-nor
+       - ti,k2g-qspi
+       - ti,am654-ospi
+       - intel,lgm-qspi
+
+  reg:
+    maxItems: 2
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  cdns,fifo-depth:
+    description:
+     Depth of hardware FIFOs.
+    allOf:
+      - $ref: "/schemas/types.yaml#/definitions/uint32"
+      - enum: [ 128, 256 ]
+      - default: 128
+
+  cdns,fifo-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      4 byte bus width of the data FIFO in bytes.
+
+  cdns,trigger-address:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      32-bit indirect AHB trigger address.
+
+  cdns,rclk-en:
+    type: boolean
+    description: |
+      Flag to indicate that QSPI return clock is used to latch the read data
+      rather than the QSPI clock. Make sure that QSPI return clock is populated
+      on the board before using this property.
+
+# subnode's properties
+patternProperties:
+  "^.*@[0-9a-fa-f]+$":
+    type: object
+    description:
+      flash device uses the subnodes below defined properties.
+
+  cdns,read-delay:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Delay for read capture logic, in clock cycles.
+
+  cdns,tshsl-ns:
+    description: |
+      Delay in nanoseconds for the length that the master mode chip select
+      outputs are de-asserted between transactions.
+
+  cdns,tsd2d-ns:
+    description: |
+      Delay in nanoseconds between one chip select being de-activated
+      and the activation of another.
+
+  cdns,tchsh-ns:
+    description: |
+      Delay in nanoseconds between last bit of current transaction and
+      deasserting the device chip select (qspi_n_ss_out).
+
+  cdns,tslch-ns:
+    description: |
+      Delay in nanoseconds between setting qspi_n_ss_out low and
+      first bit transfer.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - cdns,fifo-depth
+  - cdns,fifo-width
+  - cdns,trigger-address
+
+examples:
+  - |
+    spi@ff705000 {
+          compatible = "cdns,qspi-nor";
+          #address-cells = <1>;
+          #size-cells = <0>;
+          reg = <0xff705000 0x1000>,
+                <0xffa00000 0x1000>;
+          interrupts = <0 151 4>;
+          clocks = <&qspi_clk>;
+          cdns,fifo-depth = <128>;
+          cdns,fifo-width = <4>;
+          cdns,trigger-address = <0x00000000>;
+
+          flash@0 {
+              compatible = "jedec,spi-nor";
+              reg = <0x0>;
+              cdns,read-delay = <4>;
+              cdns,tshsl-ns = <50>;
+              cdns,tsd2d-ns = <50>;
+              cdns,tchsh-ns = <4>;
+              cdns,tslch-ns = <4>;
+          };
+    };
+