@@ -85,6 +85,7 @@ struct meson8b_dwmac {
phy_interface_t phy_mode;
struct clk *rgmii_tx_clk;
u32 tx_delay_ns;
+ u32 rx_delay_ns;
struct clk *timing_adj_clk;
};
@@ -284,25 +285,64 @@ static int meson8b_devm_clk_prepare_enable(struct meson8b_dwmac *dwmac,
static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
{
+ u32 tx_dly_config, rx_dly_config, delay_config;
int ret;
- u8 tx_dly_val = 0;
+
+ tx_dly_config = FIELD_PREP(PRG_ETH0_TXDLY_MASK,
+ dwmac->tx_delay_ns >> 1);
+
+ if (dwmac->rx_delay_ns == 2)
+ rx_dly_config = PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP;
+ else
+ rx_dly_config = 0;
switch (dwmac->phy_mode) {
case PHY_INTERFACE_MODE_RGMII:
+ delay_config = tx_dly_config | rx_dly_config;
+ break;
case PHY_INTERFACE_MODE_RGMII_RXID:
- tx_dly_val = dwmac->tx_delay_ns >> 1;
- /* fall through */
-
- case PHY_INTERFACE_MODE_RGMII_ID:
+ delay_config = tx_dly_config;
+ break;
case PHY_INTERFACE_MODE_RGMII_TXID:
+ delay_config = rx_dly_config;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RMII:
+ delay_config = 0;
+ break;
+ default:
+ dev_err(dwmac->dev, "unsupported phy-mode %s\n",
+ phy_modes(dwmac->phy_mode));
+ return -EINVAL;
+ };
+
+ if (rx_dly_config & PRG_ETH0_ADJ_ENABLE) {
+ if (!dwmac->timing_adj_clk) {
+ dev_err(dwmac->dev,
+ "The timing-adjustment clock is mandatory for the RX delay re-timing\n");
+ return -EINVAL;
+ }
+
+ /* The timing adjustment logic is driven by a separate clock */
+ ret = meson8b_devm_clk_prepare_enable(dwmac,
+ dwmac->timing_adj_clk);
+ if (ret) {
+ dev_err(dwmac->dev,
+ "Failed to enable the timing-adjustment clock\n");
+ return ret;
+ }
+ }
+
+ meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK |
+ PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP |
+ PRG_ETH0_ADJ_DELAY | PRG_ETH0_ADJ_SKEW,
+ delay_config);
+
+ if (phy_interface_mode_is_rgmii(dwmac->phy_mode)) {
/* only relevant for RMII mode -> disable in RGMII mode */
meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
PRG_ETH0_INVERTED_RMII_CLK, 0);
- meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
- FIELD_PREP(PRG_ETH0_TXDLY_MASK,
- tx_dly_val));
-
/* Configure the 125MHz RGMII TX clock, the IP block changes
* the output automatically (= without us having to configure
* a register) based on the line-speed (125MHz for Gbit speeds,
@@ -322,24 +362,11 @@ static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
"failed to enable the RGMII TX clock\n");
return ret;
}
- break;
-
- case PHY_INTERFACE_MODE_RMII:
+ } else {
/* invert internal clk_rmii_i to generate 25/2.5 tx_rx_clk */
meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
PRG_ETH0_INVERTED_RMII_CLK,
PRG_ETH0_INVERTED_RMII_CLK);
-
- /* TX clock delay cannot be configured in RMII mode */
- meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
- 0);
-
- break;
-
- default:
- dev_err(dwmac->dev, "unsupported phy-mode %s\n",
- phy_modes(dwmac->phy_mode));
- return -EINVAL;
}
/* enable TX_CLK and PHY_REF_CLK generator */
@@ -394,6 +421,18 @@ static int meson8b_dwmac_probe(struct platform_device *pdev)
&dwmac->tx_delay_ns))
dwmac->tx_delay_ns = 2;
+ /* use 0ns as fallback since this is what most boards actually use */
+ if (of_property_read_u32(pdev->dev.of_node, "amlogic,rx-delay-ns",
+ &dwmac->rx_delay_ns))
+ dwmac->rx_delay_ns = 0;
+
+ if (dwmac->rx_delay_ns != 0 && dwmac->rx_delay_ns != 2) {
+ dev_err(&pdev->dev,
+ "The only allowed RX delays values are: 0ns, 2ns");
+ ret = -EINVAL;
+ goto err_remove_config_dt;
+ }
+
dwmac->timing_adj_clk = devm_clk_get_optional(dwmac->dev,
"timing-adjustment");
if (IS_ERR(dwmac->timing_adj_clk)) {
Configure the PRG_ETH0_ADJ_* bits to enable or disable the RX delay based on the various RGMII PHY modes. For now the only supported RX delay settings are: - disabled, use for example for phy-mode "rgmii-id" - 0ns - this is treated identical to "disabled", used for example on boards where the PHY provides 2ns TX delay and the PCB trace length already adds 2ns RX delay - 2ns - for whenever the PHY cannot add the RX delay and the traces on the PCB don't add any RX delay Disabling the RX delay (in case u-boot enables it, which is the case for example on Meson8b Odroid-C1) simply means that PRG_ETH0_ADJ_ENABLE, PRG_ETH0_ADJ_SETUP, PRG_ETH0_ADJ_DELAY and PRG_ETH0_ADJ_SKEW should be disabled (just disabling PRG_ETH0_ADJ_ENABLE may be enough, since that disables the whole re-timing logic - but I find it makes more sense to clear the other bits as well since they depend on that setting). u-boot on Odroid-C1 uses the following steps to enable a 2ns RX delay: - enabling enabling the timing adjustment clock - enabling the timing adjustment logic by setting PRG_ETH0_ADJ_ENABLE - setting the PRG_ETH0_ADJ_SETUP bit The documentation for the PRG_ETH0_ADJ_DELAY and PRG_ETH0_ADJ_SKEW registers indicates that we can even set different RX delays. However, I could not find out how this works exactly, so for now we only support a 2ns RX delay using the exact same way that Odroid-C1's u-boot does. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> --- .../ethernet/stmicro/stmmac/dwmac-meson8b.c | 85 ++++++++++++++----- 1 file changed, 62 insertions(+), 23 deletions(-)