diff mbox series

[v5,6/8] drm/panel: Add ilitek ili9341 panel driver

Message ID 1590378348-8115-7-git-send-email-dillon.minfei@gmail.com (mailing list archive)
State Superseded
Headers show
Series Enable ili9341 and l3gd20 on stm32f429-disco | expand

Commit Message

Dillon Min May 25, 2020, 3:45 a.m. UTC
From: dillon min <dillon.minfei@gmail.com>

    This driver combine tiny/ili9341.c mipi_dbi_interface driver
    with mipi_dpi_interface driver, can support ili9341 with serial
    mode or parallel rgb interface mode by register configuration.

Changes since V3:

    accoding to Linus Walleij's suggestion.
    1 add more comments to driver.
    2 reduce magic number usage in the driver.
    3 move panel configuration from common place to system configuration.
    4 reuse MIPI_DCS_* as more as possible.

Signed-off-by: dillon min <dillon.minfei@gmail.com>
---
 drivers/gpu/drm/panel/Kconfig                |   12 +
 drivers/gpu/drm/panel/Makefile               |    1 +
 drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 1301 ++++++++++++++++++++++++++
 3 files changed, 1314 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c

Comments

Linus Walleij May 25, 2020, 12:23 p.m. UTC | #1
On Mon, May 25, 2020 at 5:46 AM <dillon.minfei@gmail.com> wrote:

> From: dillon min <dillon.minfei@gmail.com>
>
>     This driver combine tiny/ili9341.c mipi_dbi_interface driver
>     with mipi_dpi_interface driver, can support ili9341 with serial
>     mode or parallel rgb interface mode by register configuration.
>
> Changes since V3:
>
>     accoding to Linus Walleij's suggestion.
>     1 add more comments to driver.
>     2 reduce magic number usage in the driver.
>     3 move panel configuration from common place to system configuration.
>     4 reuse MIPI_DCS_* as more as possible.
>
> Signed-off-by: dillon min <dillon.minfei@gmail.com>

This looks good to me!
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij
Andy Shevchenko May 26, 2020, 7:46 a.m. UTC | #2
On Mon, May 25, 2020 at 6:46 AM <dillon.minfei@gmail.com> wrote:
>
> From: dillon min <dillon.minfei@gmail.com>
>
>     This driver combine tiny/ili9341.c mipi_dbi_interface driver
>     with mipi_dpi_interface driver, can support ili9341 with serial
>     mode or parallel rgb interface mode by register configuration.

Noralf told once that this driver should be unified with mi0283qt.c.

So, what should we do here?
Dillon Min May 26, 2020, 9:08 a.m. UTC | #3
Hi Andy,

Thanks for input.

On Tue, May 26, 2020 at 3:46 PM Andy Shevchenko
<andy.shevchenko@gmail.com> wrote:
>
> On Mon, May 25, 2020 at 6:46 AM <dillon.minfei@gmail.com> wrote:
> >
> > From: dillon min <dillon.minfei@gmail.com>
> >
> >     This driver combine tiny/ili9341.c mipi_dbi_interface driver
> >     with mipi_dpi_interface driver, can support ili9341 with serial
> >     mode or parallel rgb interface mode by register configuration.
>
> Noralf told once that this driver should be unified with mi0283qt.c.
>
> So, what should we do here?
>
> --
> With Best Regards,
> Andy Shevchenko

from sam's suggestion, we can't setup two drivers to support one panel
in the tree. so, i copy the mipi dbi part from tiny/ili9341.c. to this driver
from register settings and dts binding is keep the same to tiny/ili9341.c.

so, in my opinion if tiny/ili9341.c is unified with mi0283qt.c, this
driver should be
too.

thanks.

best regards,

Dillon,
Noralf Trønnes May 26, 2020, 10:38 a.m. UTC | #4
Den 26.05.2020 11.08, skrev dillon min:
> Hi Andy,
> 
> Thanks for input.
> 
> On Tue, May 26, 2020 at 3:46 PM Andy Shevchenko
> <andy.shevchenko@gmail.com> wrote:
>>
>> On Mon, May 25, 2020 at 6:46 AM <dillon.minfei@gmail.com> wrote:
>>>
>>> From: dillon min <dillon.minfei@gmail.com>
>>>
>>>     This driver combine tiny/ili9341.c mipi_dbi_interface driver
>>>     with mipi_dpi_interface driver, can support ili9341 with serial
>>>     mode or parallel rgb interface mode by register configuration.
>>
>> Noralf told once that this driver should be unified with mi0283qt.c.
>>
>> So, what should we do here?
>>
>> --
>> With Best Regards,
>> Andy Shevchenko
> 
> from sam's suggestion, we can't setup two drivers to support one panel
> in the tree. so, i copy the mipi dbi part from tiny/ili9341.c. to this driver
> from register settings and dts binding is keep the same to tiny/ili9341.c.
> 
> so, in my opinion if tiny/ili9341.c is unified with mi0283qt.c, this
> driver should be
> too.
> 

There's a discussion about MIPI DBI panels here:

MIPI DSI, DBI, and tinydrm drivers
https://lists.freedesktop.org/archives/dri-devel/2020-May/267031.html

Noralf.

> thanks.
> 
> best regards,
> 
> Dillon,
>
Dillon Min June 30, 2020, 3:32 p.m. UTC | #5
Hi Andy, Noralf,

gentle ping for this patch set,
do we have any new structure, or idea to support both dpi and dbi
interface by one drm panel driver?
from this thread
https://lists.freedesktop.org/archives/dri-devel/2020-May/267031.html
, it's seems
discussing was stopped at may 25.

if there are any new information about this topic, please feel free to
let me know. hope i can make some
progress on it.

thanks,

Dillon,

best regards

On Tue, May 26, 2020 at 6:38 PM Noralf Trønnes <noralf@tronnes.org> wrote:
>
>
>
> Den 26.05.2020 11.08, skrev dillon min:
> > Hi Andy,
> >
> > Thanks for input.
> >
> > On Tue, May 26, 2020 at 3:46 PM Andy Shevchenko
> > <andy.shevchenko@gmail.com> wrote:
> >>
> >> On Mon, May 25, 2020 at 6:46 AM <dillon.minfei@gmail.com> wrote:
> >>>
> >>> From: dillon min <dillon.minfei@gmail.com>
> >>>
> >>>     This driver combine tiny/ili9341.c mipi_dbi_interface driver
> >>>     with mipi_dpi_interface driver, can support ili9341 with serial
> >>>     mode or parallel rgb interface mode by register configuration.
> >>
> >> Noralf told once that this driver should be unified with mi0283qt.c.
> >>
> >> So, what should we do here?
> >>
> >> --
> >> With Best Regards,
> >> Andy Shevchenko
> >
> > from sam's suggestion, we can't setup two drivers to support one panel
> > in the tree. so, i copy the mipi dbi part from tiny/ili9341.c. to this driver
> > from register settings and dts binding is keep the same to tiny/ili9341.c.
> >
> > so, in my opinion if tiny/ili9341.c is unified with mi0283qt.c, this
> > driver should be
> > too.
> >
>
> There's a discussion about MIPI DBI panels here:
>
> MIPI DSI, DBI, and tinydrm drivers
> https://lists.freedesktop.org/archives/dri-devel/2020-May/267031.html
>
> Noralf.
>
> > thanks.
> >
> > best regards,
> >
> > Dillon,
> >
diff mbox series

Patch

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index a1723c1..c938bee 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -95,6 +95,18 @@  config DRM_PANEL_ILITEK_IL9322
 	  Say Y here if you want to enable support for Ilitek IL9322
 	  QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
 
+config DRM_PANEL_ILITEK_ILI9341
+	tristate "Ilitek ILI9341 240x320 QVGA panels"
+	depends on OF && SPI
+	depends on DRM_KMS_HELPER
+	depends on DRM_KMS_CMA_HELPER
+	depends on BACKLIGHT_CLASS_DEVICE
+	select DRM_MIPI_DBI
+	help
+	  Say Y here if you want to enable support for Ilitek IL9341
+	  QVGA (240x320) RGB panels. support serial & parallel rgb
+	  interface.
+
 config DRM_PANEL_ILITEK_ILI9881C
 	tristate "Ilitek ILI9881C-based panels"
 	depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 96a883c..16947d7 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -8,6 +8,7 @@  obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
 obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
 obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
+obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
 obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
 obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
new file mode 100644
index 0000000..dd6f860
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
@@ -0,0 +1,1301 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Ilitek ILI9341 TFT LCD drm_panel driver.
+ *
+ * This panel can be configured to support:
+ * - 16-bit parallel RGB interface
+ * - 18-bit parallel RGB interface
+ * - 4-line serial spi interface
+ *
+ * Copyright (C) 2020 Dillon Min <dillon.minfei@gmail.com>
+ * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+#include <linux/delay.h>
+#include <video/mipi_display.h>
+#include <drm/drm_mipi_dbi.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_atomic_helper.h>
+
+#include <drm/drm_drv.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+
+#define ILI9341_RGB_INTERFACE  0xb0   /* RGB Interface Signal Control */
+#define ILI9341_FRC            0xb1   /* Frame Rate Control register */
+#define ILI9341_DFC            0xb6   /* Display Function Control register */
+#define ILI9341_POWER1         0xc0   /* Power Control 1 register */
+#define ILI9341_POWER2         0xc1   /* Power Control 2 register */
+#define ILI9341_VCOM1          0xc5   /* VCOM Control 1 register */
+#define ILI9341_VCOM2          0xc7   /* VCOM Control 2 register */
+#define ILI9341_POWERA         0xcb   /* Power control A register */
+#define ILI9341_POWERB         0xcf   /* Power control B register */
+#define ILI9341_PGAMMA         0xe0   /* Positive Gamma Correction register */
+#define ILI9341_NGAMMA         0xe1   /* Negative Gamma Correction register */
+#define ILI9341_DTCA           0xe8   /* Driver timing control A */
+#define ILI9341_DTCB           0xea   /* Driver timing control B */
+#define ILI9341_POWER_SEQ      0xed   /* Power on sequence register */
+#define ILI9341_3GAMMA_EN      0xf2   /* 3 Gamma enable register */
+#define ILI9341_INTERFACE      0xf6   /* Interface control register */
+#define ILI9341_PRC            0xf7   /* Pump ratio control register */
+#define ILI9341_ETMOD	       0xb7   /* Entry mode set */
+
+#define ILI9341_MADCTL_BGR	BIT(3)
+#define ILI9341_MADCTL_MV	BIT(5)
+#define ILI9341_MADCTL_MX	BIT(6)
+#define ILI9341_MADCTL_MY	BIT(7)
+
+
+#define ILI9341_POWER_B_LEN	3
+#define ILI9341_POWER_SEQ_LEN	4
+#define ILI9341_DTCA_LEN	3
+#define ILI9341_DTCB_LEN	2
+#define ILI9341_POWER_A_LEN	5
+#define ILI9341_DFC_1_LEN	2
+#define ILI9341_FRC_LEN		2
+#define ILI9341_VCOM_1_LEN	2
+#define ILI9341_DFC_2_LEN	4
+#define ILI9341_COLUMN_ADDR_LEN	4
+#define ILI9341_PAGE_ADDR_LEN	4
+#define ILI9341_INTERFACE_LEN	3
+#define ILI9341_PGAMMA_LEN	15
+#define ILI9341_NGAMMA_LEN	15
+#define ILI9341_CA_LEN		3
+
+#define ILI9341_PIXEL_DPI_16_BITS	(BIT(6)|BIT(4))
+#define ILI9341_PIXEL_DPI_18_BITS	(BIT(6)|BIT(5))
+#define ILI9341_GAMMA_CURVE_1		BIT(0)
+#define ILI9341_IF_WE_MODE		BIT(0)
+#define ILI9341_IF_BIG_ENDIAN		0x00
+#define ILI9341_IF_DM_RGB		BIT(2)
+#define ILI9341_IF_DM_INTERNAL		0x00
+#define ILI9341_IF_DM_VSYNC		BIT(3)
+#define ILI9341_IF_RM_RGB		BIT(1)
+#define ILI9341_IF_RIM_RGB		0x00
+
+#define ILI9341_COLUMN_ADDR		0x00ef
+#define ILI9341_PAGE_ADDR		0x013f
+
+#define ILI9341_RGB_EPL			BIT(0)
+#define ILI9341_RGB_DPL			BIT(1)
+#define ILI9341_RGB_HSPL		BIT(2)
+#define ILI9341_RGB_VSPL		BIT(3)
+#define ILI9341_RGB_DE_MODE		BIT(6)
+#define ILI9341_RGB_DISP_PATH_MEM	BIT(7)
+
+#define ILI9341_DBI_VCOMH_4P6V		0x23
+#define ILI9341_DBI_PWR_2_DEFAULT	0x10
+#define ILI9341_DBI_PRC_NORMAL		0x20
+#define ILI9341_DBI_VCOM_1_VMH_4P25V	0x3e
+#define ILI9341_DBI_VCOM_1_VML_1P5V	0x28
+#define ILI9341_DBI_VCOM_2_DEC_58	0x86
+#define ILI9341_DBI_FRC_DIVA		0x00
+#define ILI9341_DBI_FRC_RTNA		0x1b
+#define ILI9341_DBI_EMS_GAS		BIT(0)
+#define ILI9341_DBI_EMS_DTS		BIT(1)
+#define ILI9341_DBI_EMS_GON		BIT(2)
+/**
+ * ili9341_command - ili9341 command with optional parameter(s)
+ * @ili: struct ili9341
+ * @cmd: Command
+ * @seq...: Optional parameter(s)
+ *
+ * Send command to the controller.
+ *
+ * Returns:
+ * Zero on success, negative error code on failure.
+ */
+#define ili9341_command(ili, cmd, seq...) \
+({ \
+	u8 d[] = { seq }; \
+	_ili9341_command(ili, cmd, d, ARRAY_SIZE(d)); \
+})
+
+/**
+ * struct ili9341_config - the system specific ILI9341 configuration
+ * @max_spi_speed: 10000000
+ */
+struct ili9341_config {
+	u32 max_spi_speed;
+
+	const struct drm_display_mode mode;
+	/* TODO: need comments for this register */
+	u8 ca[ILI9341_CA_LEN];
+	/* TODO: need comments for this register */
+	u8 power_b[ILI9341_POWER_B_LEN];
+	/* TODO: need comments for this register */
+	u8 power_seq[ILI9341_POWER_SEQ_LEN];
+	/* TODO: need comments for this register */
+	u8 dtca[ILI9341_DTCA_LEN];
+	/* TODO: need comments for this register */
+	u8 dtcb[ILI9341_DTCB_LEN];
+	/* TODO: need comments for this register */
+	u8 power_a[ILI9341_POWER_A_LEN];
+	/*
+	 * Frame Rate Control (In Normal Mode/Full Colors) (B1h)
+	 *
+	 * Formula to calculate frame frequency:
+	 * Frame Rate=fosc/(Clocks per line x Division ratio x
+	 * (Lines+VBP+VFP))
+	 *
+	 * Sets the division ratio for internal clocks of Normal mode at MCU
+	 * interface.
+	 *
+	 * fosc : internal oscillator frequency
+	 * Clocks per line : RTNA setting
+	 * Division ratio : DIVA setting
+	 * Lines : total driving line number
+	 * VBP : back porch line number
+	 * VFP : front porch line number
+	 *
+	 * RTNA [4:0] Frame Rate (Hz)   RTNA [4:0] Frame Rate (Hz)
+	 * 1 0 0 0 0  119		1 1 0 0 0  79
+	 * 1 0 0 0 1  112		1 1 0 0 1  76
+	 * 1 0 0 1 0  106		1 1 0 1 0  73
+	 * 1 0 0 1 1  100		1 1 0 1 1  70(default)
+	 * 1 0 1 0 0  95		1 1 1 0 0  68
+	 * 1 0 1 0 1  90		1 1 1 0 1  65
+	 * 1 0 1 1 0  86		1 1 1 0 1  63
+	 * 1 0 1 1 1  83		1 1 1 1 1  61
+	 *
+	 * DIVA [1:0] : division ratio for internal clocks when Normal mode.
+	 *
+	 * DIVA [1:0] Division Ratio
+	 * 0 0 fosc
+	 * 0 1 fosc / 2
+	 * 1 0 fosc / 4
+	 * 1 1 fosc / 8
+	 *
+	 */
+	u8 frc[ILI9341_FRC_LEN];
+	/* TODO: need comments for this register */
+	u8 prc;
+	/*
+	 * B6h DISCTRL (Display Function Control)
+	 *               D/CX RDX WRX D17-8 D7  D6 D5 D4 D3   D2  D1  D0  HEX
+	 * Command       0    1   M   XX    1   0  1  1  0    1   1   0   B6h
+	 * 1st Parameter 1    1   M   XX    0   0  0  0  PTG[1:0] PT[1:0] 0A
+	 * 2nd Parameter 1    1   M   XX    REV GS SS SM ISC[3:0]         82
+	 * 3rd Parameter 1    1   M   XX    0   0  NL[5:0]                27
+	 * 4th Parameter 1    1   M   XX    0   0  PCDIV[5:0]             XX
+	 *
+	 * PTG [1:0]: Set the scan mode in non-display area.
+	 * PTG1 | PTG0 | Gate outputs in   | Source outputs in  | VCOM output
+	 *               non-display area  | non-display area   |
+	 * 1      0      Interval scan       Set with the PT[2:0] bits
+	 *
+	 * PT [1:0]: Determine source/VCOM output in a non-display area in the
+	 * partial display mode.
+	 * 1    0    AGND       AGND       AGND         AGND
+	 *
+	 * REV: Select whether the liquid crystal type is normally white type
+	 * or normally black type.
+	 * REV   Liquid crystal type
+	 * 0     Normally black
+	 * 1     Normally white
+	 *
+	 * SS: Select the shift direction of outputs from the source driver.
+	 * SS    Source Output Scan Direction
+	 * 0     S1 -> S720
+	 * 1     S720 -> S1
+	 *
+	 * GS: Sets the direction of scan by the gate driver in the range
+	 * determined by SCN [4:0] and NL [4:0]. The scan direction
+	 * determined by GS = 0 can be reversed by setting GS = 1.
+	 *
+	 * GS     Gate Output Scan Direction
+	 * 0      G1 -> G320
+	 * 1      G320 -> G1
+	 */
+	u8 dfc_1[ILI9341_DFC_1_LEN];
+	/*
+	 * Power Control 1 (C0h)
+	 * VRH [5:0]: Set the GVDD level, which is a reference level for the
+	 * VCOM level and the grayscale voltage level.
+	 *
+	 * VRH[5:0]    GVDD			VRH[5:0]	GVDD
+	 * 0 0 0 0 0 0 Setting prohibited	1 0 0 0 0 0	4.45 V
+	 * 0 0 0 0 0 1 Setting prohibited	1 0 0 0 0 1	4.50 V
+	 * 0 0 0 0 1 0 Setting prohibited	1 0 0 0 1 0	4.55 V
+	 * 0 0 0 0 1 1 3.00 V			1 0 0 0 1 1	4.60 V
+	 * 0 0 0 1 0 0 3.05 V			1 0 0 1 0 0	4.65 V
+	 * 0 0 0 1 0 1 3.10 V			1 0 0 1 0 1	4.70 V
+	 * 0 0 0 1 1 0 3.15 V			1 0 0 1 1 0	4.75 V
+	 * 0 0 0 1 1 1 3.20 V			1 0 0 1 1 1	4.80 V
+	 * 0 0 1 0 0 0 3.25 V			1 0 1 0 0 0	4.85 V
+	 * 0 0 1 0 0 1 3.30 V			1 0 1 0 0 1	4.90 V
+	 * 0 0 1 0 1 0 3.35 V			1 0 1 0 1 0	4.95 V
+	 * 0 0 1 0 1 1 3.40 V			1 0 1 0 1 1	5.00 V
+	 * 0 0 1 1 0 0 3.45 V			1 0 1 1 0 0	5.05 V
+	 * 0 0 1 1 0 1 3.50 V			1 0 1 1 0 1	5.10 V
+	 * 0 0 1 1 1 0 3.55 V			1 0 1 1 1 0	5.15 V
+	 * 0 0 1 1 1 1 3.60 V			1 0 1 1 1 1	5.20 V
+	 * 0 1 0 0 0 0 3.65 V			1 1 0 0 0 0	5.25 V
+	 * 0 1 0 0 0 1 3.70 V			1 1 0 0 0 1	5.30 V
+	 * 0 1 0 0 1 0 3.75 V			1 1 0 0 1 0	5.35 V
+	 * 0 1 0 0 1 1 3.80 V			1 1 0 0 1 1	5.40 V
+	 * 0 1 0 1 0 0 3.85 V			1 1 0 1 0 0	5.45 V
+	 * 0 1 0 1 0 1 3.90 V			1 1 0 1 0 1	5.50 V
+	 * 0 1 0 1 1 0 3.95 V			1 1 0 1 1 0	5.55 V
+	 * 0 1 0 1 1 1 4.00 V			1 1 0 1 1 1	5.60 V
+	 * 0 1 1 0 0 0 4.05 V			1 1 1 0 0 0	5.65 V
+	 * 0 1 1 0 0 1 4.10 V			1 1 1 0 0 1	5.70 V
+	 * 0 1 1 0 1 0 4.15 V			1 1 1 0 1 0	5.75 V
+	 * 0 1 1 0 1 1 4.20 V			1 1 1 0 1 1	5.80 V
+	 * 0 1 1 1 0 0 4.25 V			1 1 1 1 0 0	5.85 V
+	 * 0 1 1 1 0 1 4.30 V			1 1 1 1 0 1	5.90 V
+	 * 0 1 1 1 1 0 4.35 V			1 1 1 1 1 0	5.95 V
+	 * 0 1 1 1 1 1 4.40 V			1 1 1 1 1 1	6.00 V
+	 */
+	u8 power_1;
+	/*
+	 * Power Control 2 (C1h)
+	 *
+	 * BT [2:0]: Sets the factor used in the step-up circuits.
+	 * Select the optimal step-up factor for the operating voltage. To
+	 * reduce power consumption, set a smaller factor.
+	 *
+	 * BT[2:0]   AVDD     VGH      VGL
+	 * 0 0 0     VCI x 2  VCI x 7  VCI x 4
+	 * 0 0 1                       VCI x 3
+	 * 0 1 0              VCI x 6  VCI x 4
+	 * 0 1 1		       VCI x 3
+	 *
+	 */
+	u8 power_2;
+	/*
+	 * VCOM Control 1(C5h)
+	 *
+	 * VMH [6:0] : Set the VCOMH voltage
+	 *
+	 * VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH
+	 * 0000000  2.700    0100000  3.500    1000000  4.300    1100000  5.100
+	 * 0000001  2.725    0100001  3.525    1000001  4.325    1100001  5.125
+	 * 0000010  2.750    0100010  3.550    1000010  4.350    1100010  5.150
+	 * 0000011  2.775    0100011  3.575    1000011  4.375    1100011  5.175
+	 * 0000100  2.800    0100100  3.600    1000100  4.400    1100100  5.200
+	 * 0000101  2.825    0100101  3.625    1000101  4.425    1100101  5.225
+	 * 0000110  2.850    0100110  3.650    1000110  4.450    1100110  5.250
+	 * 0000111  2.875    0100111  3.675    1000111  4.475 	 1100111  5.275
+	 * 0001000  2.900    0101000  3.700    1001000  4.500 	 1101000  5.300
+	 * 0001001  2.925    0101001  3.725    1001001  4.525 	 1101001  5.325
+	 * 0001010  2.950    0101010  3.750    1001010  4.550 	 1101010  5.350
+	 * 0001011  2.975    0101011  3.775    1001011  4.575 	 1101011  5.375
+	 * 0001100  3.000    0101100  3.800    1001100  4.600 	 1101100  5.400
+	 * 0001101  3.025    0101101  3.825    1001101  4.625 	 1101101  5.425
+	 * 0001110  3.050    0101110  3.850    1001110  4.650 	 1101110  5.450
+	 * 0001111  3.075    0101111  3.875    1001111  4.675 	 1101111  5.475
+	 * 0010000  3.100    0110000  3.900    1010000  4.700 	 1110000  5.500
+	 * 0010001  3.125    0110001  3.925    1010001  4.725 	 1110001  5.525
+	 * 0010010  3.150    0110010  3.950    1010010  4.750 	 1110010  5.550
+	 * 0010011  3.175    0110011  3.975    1010011  4.775 	 1110011  5.575
+	 * 0010100  3.200    0110100  4.000    1010100  4.800 	 1110100  5.600
+	 * 0010101  3.225    0110101  4.025    1010101  4.825 	 1110101  5.625
+	 * 0010110  3.250    0110110  4.050    1010110  4.850 	 1110110  5.650
+	 * 0010111  3.275    0110111  4.075    1010111  4.875 	 1110111  5.675
+	 * 0011000  3.300    0111000  4.100    1011000  4.900 	 1111000  5.700
+	 * 0011001  3.325    0111001  4.125    1011001  4.925 	 1111001  5.725
+	 * 0011010  3.350    0111010  4.150    1011010  4.950 	 1111010  5.750
+	 * 0011011  3.375    0111011  4.175    1011011  4.975 	 1111011  5.775
+	 * 0011100  3.400    0111100  4.200    1011100  5.000 	 1111100  5.800
+	 * 0011101  3.425    0111101  4.225    1011101  5.025 	 1111101  5.825
+	 * 0011110  3.450    0111110  4.250    1011110  5.050 	 1111110  5.850
+	 * 0011111  3.475    0111111  4.275    1011111  5.075    1111111  5.875
+	 *
+	 * VML[6:0] : Set the VCOML voltage
+	 *
+	 * VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML
+	 * 0000000 -2.500 0100000 -1.700 1000000 -0.900 1100000 -0.100
+	 * 0000001 -2.475 0100001 -1.675 1000001 -0.875 1100001 -0.075
+	 * 0000010 -2.450 0100010 -1.650 1000010 -0.850 1100010 -0.050
+	 * 0000011 -2.425 0100011 -1.625 1000011 -0.825 1100011 -0.025
+	 * 0000100 -2.400 0100100 -1.600 1000100 -0.800 1100100 0
+	 * 0000101 -2.375 0100101 -1.575 1000101 -0.775 1100101 Reserved
+	 * 0000110 -2.350 0100110 -1.550 1000110 -0.750 1100110 Reserved
+	 * 0000111 -2.325 0100111 -1.525 1000111 -0.725 1100111 Reserved
+	 * 0001000 -2.300 0101000 -1.500 1001000 -0.700 1101000 Reserved
+	 * 0001001 -2.275 0101001 -1.475 1001001 -0.675 1101001 Reserved
+	 * 0001010 -2.250 0101010 -1.450 1001010 -0.650 1101010 Reserved
+	 * 0001011 -2.225 0101011 -1.425 1001011 -0.625 1101011 Reserved
+	 * 0001100 -2.200 0101100 -1.400 1001100 -0.600 1101100 Reserved
+	 * 0001101 -2.175 0101101 -1.375 1001101 -0.575 1101101 Reserved
+	 * 0001110 -2.150 0101110 -1.350 1001110 -0.550 1101110 Reserved
+	 * 0001111 -2.125 0101111 -1.325 1001111 -0.525 1101111 Reserved
+	 * 0010000 -2.100 0110000 -1.300 1010000 -0.500 1110000 Reserved
+	 * 0010001 -2.075 0110001 -1.275 1010001 -0.475 1110001 Reserved
+	 * 0010010 -2.050 0110010 -1.250 1010010 -0.450 1110010 Reserved
+	 * 0010011 -2.025 0110011 -1.225 1010011 -0.425 1110011 Reserved
+	 * 0010100 -2.000 0110100 -1.200 1010100 -0.400 1110100 Reserved
+	 * 0010101 -1.975 0110101 -1.175 1010101 -0.375 1110101 Reserved
+	 * 0010110 -1.950 0110110 -1.150 1010110 -0.350 1110110 Reserved
+	 * 0010111 -1.925 0110111 -1.125 1010111 -0.325 1110111 Reserved
+	 * 0011000 -1.900 0111000 -1.100 1011000 -0.300 1111000 Reserved
+	 * 0011001 -1.875 0111001 -1.075 1011001 -0.275 1111001 Reserved
+	 * 0011010 -1.850 0111010 -1.050 1011010 -0.250 1111010 Reserved
+	 * 0011011 -1.825 0111011 -1.025 1011011 -0.225 1111011 Reserved
+	 * 0011100 -1.800 0111100 -1.000 1011100 -0.200 1111100 Reserved
+	 * 0011101 -1.775 0111101 -0.975 1011101 -0.175 1111101 Reserved
+	 * 0011110 -1.750 0111110 -0.950 1011110 -0.150 1111110 Reserved
+	 * 0011111 -1.725 0111111 -0.925 1011111 -0.125 1111111 Reserved
+	 */
+	u8 vcom_1[ILI9341_VCOM_1_LEN];
+	/*
+	 * VCOM Control 2(C7h)
+	 *
+	 * C7h		VMCTRL1 (VCOM Control 1)
+	 *		D/CX RDX WRX D17-8 D7  D6  D5 D4 D3 D2 D1 D0 HEX
+	 * Command 	0    1   M   XX    1   1   0  0  0  1  1  1  C7h
+	 * Parameter 	1    1   M   XX    nVM VMF[6:0]              C0
+	 *
+	 * nVM: nVM equals to “0” after power on reset and VCOM offset
+	 * equals to program MTP value. When nVM set to “1”, setting
+	 * of VMF [6:0] becomes valid and VCOMH/VCOML can be adjusted.
+	 *
+	 * VMF [6:0]: Set the VCOM offset voltage.
+	 */
+	u8 vcom_2;
+	/*
+	 * Memory Access Control (36h)
+	 *
+	 * 36h 		MADCTL (Memory Access Control)
+	 * 		D/CX RDX WRX D17-8 D7 D6 D5 D4 D3  D2 D1 D0 HEX
+	 * Command 	0    1   M   XX    0  0  1  1  0   1  1  0  36h
+	 * Parameter 	1    1   M   XX    MY MX MV ML BGR MH 0  0  00
+	 *
+	 * This command defines read/write scanning direction of frame memory.
+	 * This command makes no change on the other driver status.
+	 *
+	 * Bit  Name 			 Description
+	 * MY   Row Address Order
+	 * MX   Column Address Order
+	 * MV 	Row / Column Exchange 	 These 3 bits control MCU to memory
+	 * 				 write/read direction.
+	 * ML 	Vertical Refresh Order 	 LCD vertical refresh direction control.
+	 * BGR 	RGB-BGR Order		 Color selector switch control
+	 *                               (0=RGB color filter panel, 1=BGR
+	 *                               color filter panel)
+	 * MH 	Horizontal Refresh ORDER LCD horizontal refreshing
+	 * direction control.
+	 *
+	 * Note: When BGR bit is changed, the new setting is active
+	 * immediately without update the content in Frame Memory again.
+	 *
+	 */
+	u8 address_mode;
+	/* TODO: need comments for this register */
+	u8 g3amma_en;
+	/* RGB Interface Signal Control (B0h)
+	 *
+	 * B0h 		IFMODE (Interface Mode Control)
+	 * 		D/CX RDX WRX D17-8 D7 	       D6     D5     D4 D3   D2   D1  D0  HEX
+	 * Command 	0    1   M   XX    1 	       0      1      1  0    0    0   0   B0h
+	 * Parameter 	1    1   M   XX    ByPass_MODE RCM[1] RCM[0] 0  VSPL HSPL DPL EPL 40
+	 *
+	 * Sets the operation status of the display interface. The setting
+	 * becomes effective as soon as the command is received.
+	 * EPL: DE polarity (“0”= High enable for RGB interface, “1”= Low
+	 * enable for RGB interface)
+	 *
+	 * DPL: DOTCLK polarity set (“0”= data fetched at the rising time,
+	 * “1”= data fetched at the falling time)
+	 *
+	 * HSPL: HSYNC polarity (“0”= Low level sync clock, “1”= High
+	 * level sync clock)
+	 *
+	 * VSPL: VSYNC polarity (“0”= Low level sync clock, “1”= High
+	 * level sync clock)
+	 *
+	 * RCM [1:0]: RGB interface selection (refer to the RGB interface
+	 * section).
+	 *
+	 * ByPass_MODE: Select display data path whether Memory or Direct to
+	 * Shift register when RGB Interface is used.
+	 *
+	 * ByPass_MODE 	Display Data Path
+	 * 0 		Direct to Shift Register (default)
+	 * 1 		Memory
+	 */
+	u8 rgb_interface;
+	/* refer to dfc_1 */
+	u8 dfc_2[ILI9341_DFC_2_LEN];
+	/*
+	 * Column Address Set (2Ah)
+	 * This command is used to define area of frame memory where MCU can
+	 * access. This command makes no change on the
+	 * other driver status. The values of SC [15:0] and EC [15:0] are
+	 * referred when RAMWR command comes. Each value
+	 * represents one column line in the Frame Memory.
+	 */
+	u8 column_addr[ILI9341_COLUMN_ADDR_LEN];
+	/*
+	 * Page Address Set (2Bh)
+	 * This command is used to define area of frame memory where MCU can
+	 * access. This command makes no change on the
+	 * other driver status. The values of SP [15:0] and EP [15:0] are
+	 * referred when RAMWR command comes. Each value
+	 * represents one Page line in the Frame Memory.
+	 */
+	u8 page_addr[ILI9341_PAGE_ADDR_LEN];
+	/*
+	 * Interface Control (F6h)
+	 *
+	 * F6h 		IFCTL (16bits Data Format Selection)
+	 * 	        D/CX RDX WRX D17-8 D7   D6   D5     D4     D3      D2     D1     D0      HEX
+	 * Command      0    1   M   XX    1    1    1      1      0       1      1      0       F6h
+	 * 1stParameter 1    1   M   XX    MY   MX   MV
+	 * 				   _EOR _EOR _EOR   0      BGR_EOR 0      0      WE MODE 01
+	 * 2ndParameter 1    1   M   XX    0    0    EPF[1] EPF[0] 0       0      MDT[1] MDT[0]  00
+	 * 3rdParameter 1    1   M   XX    0    0    ENDIAN 0      DM[1]   DM[0]  RM     RIM     00
+	 *
+	 */
+	u8 interface[ILI9341_INTERFACE_LEN];
+	/*
+	 * This command sets the pixel format for the RGB image data used by
+	 * the interface. DPI [2:0] is the pixel format select of RGB
+	 * interface and DBI [2:0] is the pixel format of MCU interface. If a
+	 * particular interface, either RGB interface or MCU interface, is
+	 * not used then the corresponding bits in the parameter are ignored.
+	 * The pixel format is shown in the table below.
+	 *
+	 * DPI[2:0] 	RGB Interface Format 	DBI[2:0] MCU Interface Format
+	 * 0 0 0 	Reserved 		0 0 0 	 Reserved
+	 * 0 0 1 	Reserved 		0 0 1 	 Reserved
+	 * 0 1 0 	Reserved 		0 1 0 	 Reserved
+	 * 0 1 1 	Reserved 		0 1 1 	 Reserved
+	 * 1 0 0 	Reserved 		1 0 0  	 Reserved
+	 * 1 0 1 	16 bits / pixel 	1 0 1    16 bits / pixel
+	 * 1 1 0 	18 bits / pixel 	1 1 0 	 18 bits / pixel
+	 * 1 1 1 	Reserved 		1 1 1 	 Reserved
+	 *
+	 */
+	u8 pixel_format;
+	/*
+	 * This command is used to select the desired Gamma curve for the
+	 * current display. A maximum of 4 fixed gamma curves can
+	 * be selected. The curve is selected by setting the appropriate bit
+	 * in the parameter as described in the Table:
+	 *
+	 * GC [7:0] 	Curve Selected
+	 * 01h 		Gamma curve 1 (G2.2)
+	 * 02h 		---
+	 * 04h 		---
+	 * 08h 		---
+	 */
+	u8 gamma_curve;
+	/*
+	 * Positive Gamma Correction (E0h)
+	 *
+	 * Set the gray scale voltage to adjust the gamma characteristics of
+	 * the TFT panel.
+	 */
+	u8 pgamma[ILI9341_PGAMMA_LEN];
+	/*
+	 * Negative Gamma Correction (E1h)
+	 *
+	 * Set the gray scale voltage to adjust the gamma characteristics of
+	 * the TFT panel.
+	 */
+	u8 ngamma[ILI9341_NGAMMA_LEN];
+};
+
+struct ili9341 {
+	struct device *dev;
+	const struct ili9341_config *conf;
+	struct drm_panel panel;
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *dc_gpio;
+	u32 max_spi_speed;
+	struct regulator *vcc;
+};
+
+/*
+ * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller
+ */
+static const struct ili9341_config ili9341_stm32f429_disco_data = {
+	.max_spi_speed = 10000000,
+	.mode = {
+		.clock = 6100,
+		.hdisplay = 240,
+		.hsync_start = 240 + 10,/* hfp 10 */
+		.hsync_end = 240 + 10 + 10,/* hsync 10 */
+		.htotal = 240 + 10 + 10 + 20,/* hbp 20 */
+		.vdisplay = 320,
+		.vsync_start = 320 + 4,/* vfp 4 */
+		.vsync_end = 320 + 4 + 2,/* vsync 2 */
+		.vtotal = 320 + 4 + 2 + 2,/* vbp 2 */
+		.vrefresh = 60,
+		.flags = 0,
+		.width_mm = 65,
+		.height_mm = 50,
+		.type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+	},
+	/* TODO: need comments for this register */
+	.ca = {0xc3, 0x08, 0x50},
+	/* TODO: need comments for this register */
+	.power_b = {0x00, 0xc1, 0x30},
+	/* TODO: need comments for this register */
+	.power_seq = {0x64, 0x03, 0x12, 0x81},
+	/* TODO: need comments for this register */
+	.dtca = {0x85, 0x00, 0x78},
+	/* TODO: need comments for this register */
+	.power_a = {0x39, 0x2c, 0x00, 0x34, 0x02},
+	/* TODO: need comments for this register */
+	.prc = 0x20,
+	/* TODO: need comments for this register */
+	.dtcb = {0x00, 0x00},
+	/* 0x00 fosc, 0x1b 70hz */
+	.frc = {0x00, 0x1b},
+	/* 0x0a Interval scan, AGND AGND AGND AGND
+	 * 0xa2 Normally white, G1 -> G320, S720 -> S1,
+	 *	Scan Cycle 5 frames,85ms
+	 */
+	.dfc_1 = {0x0a, 0xa2},
+	/* 0x10 3.65v */
+	.power_1 = 0x10,
+	/* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */
+	.power_2 = 0x10,
+	/* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/
+	.vcom_1 = {0x45, 0x15},
+	/* 0x90 offset voltage, VMH-48, VML-48 */
+	.vcom_2 = 0x90,
+	/* 0xc8 Row Address Order, Column Address Order
+	 * 	BGR 1
+	 */
+	.address_mode = 0xc8,
+	.g3amma_en = 0x00,
+	/* 0xc2
+	 * Display Data Path: Memory
+	 * RGB: DE mode
+	 * DOTCLK polarity set (data fetched at the falling time)
+	 */
+	.rgb_interface = ILI9341_RGB_DISP_PATH_MEM |
+			ILI9341_RGB_DE_MODE |
+			ILI9341_RGB_DPL,
+	/*
+	 * 0x0a
+	 * Gate outputs in non-display area: Interval scan
+	 * Determine source/VCOM output in a non-display area in the partial
+	 * display mode: AGND AGND AGND AGND
+	 *
+	 * 0xa7
+	 * Scan Cycle: 15 frames
+	 * fFLM = 60Hz: 255ms
+	 * Liquid crystal type: Normally white
+	 * Gate Output Scan Direction: G1 -> G320
+	 * Source Output Scan Direction: S720 -> S1
+	 *
+	 * 0x27
+	 * LCD Driver Line: 320 lines
+	 *
+	 * 0x04
+	 * PCDIV: 4
+	 */
+	.dfc_2 = {0x0a, 0xa7, 0x27, 0x04},
+	/* column address: 240 */
+	.column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff,
+				ILI9341_COLUMN_ADDR & 0xff},
+	/* page address: 320 */
+	.page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff,
+				ILI9341_PAGE_ADDR & 0xff},
+	/* Memory write control: When the transfer number of data exceeds
+	 * (EC-SC+1)*(EP-SP+1), the column and page number will be
+	 * reset, and the exceeding data will be written into the following
+	 * column and page.
+	 * Display Operation Mode: RGB Interface Mode
+	 * Interface for RAM Access: RGB interface
+	 * 16- bit RGB interface (1 transfer/pixel)
+	 */
+	.interface = {ILI9341_IF_WE_MODE, 0x00,
+			ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB},
+	/* DPI: 16 bits / pixel */
+	.pixel_format = ILI9341_PIXEL_DPI_16_BITS,
+	/* Curve Selected: Gamma curve 1 (G2.2) */
+	.gamma_curve = ILI9341_GAMMA_CURVE_1,
+	.pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e,
+			0x09, 0x4e, 0x78, 0x3c, 0x09,
+			0x13, 0x05, 0x17, 0x11, 0x00},
+	.ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11,
+			0x07, 0x31, 0x33, 0x42, 0x05,
+			0x0c, 0x0a, 0x28, 0x2f, 0x0f},
+};
+static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel)
+{
+	return container_of(panel, struct ili9341, panel);
+}
+
+int ili9341_spi_transfer(struct spi_device *spi, u32 speed_hz,
+			  u8 bpw, const void *buf, size_t len)
+{
+	size_t max_chunk = spi_max_transfer_size(spi);
+	struct spi_transfer tr = {
+		.bits_per_word = bpw,
+		.speed_hz = speed_hz,
+		.len = len,
+	};
+	struct spi_message m;
+	size_t chunk;
+	int ret;
+
+	spi_message_init_with_transfers(&m, &tr, 1);
+
+	while (len) {
+		chunk = min(len, max_chunk);
+
+		tr.tx_buf = buf;
+		tr.len = chunk;
+		buf += chunk;
+		len -= chunk;
+
+		ret = spi_sync(spi, &m);
+		if (ret) {
+			dev_err(&spi->dev, "spi_sync error: %d\n", ret);
+			return ret;
+		}
+	}
+	return 0;
+}
+
+static int _ili9341_command(struct ili9341 *ili, u8 cmd, const void *data,
+				    size_t count)
+{
+	struct spi_device *spi = to_spi_device(ili->dev);
+	int ret = 0;
+
+	gpiod_set_value_cansleep(ili->dc_gpio, 0);
+
+	ret = ili9341_spi_transfer(spi, ili->max_spi_speed, 8,
+					(const void *)&cmd, 1);
+	if (ret || data == NULL || count == 0)
+		return ret;
+
+	gpiod_set_value_cansleep(ili->dc_gpio, 1);
+
+	return ili9341_spi_transfer(spi, ili->max_spi_speed, 8,
+		data, count);
+}
+
+static int ili9341_dpi_init(struct ili9341 *ili)
+{
+	int ret;
+	ret = _ili9341_command(ili, 0xca,
+			ili->conf->ca,
+			ILI9341_CA_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_POWERB,
+			ili->conf->power_b,
+			ILI9341_POWER_B_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_POWER_SEQ,
+			ili->conf->power_seq,
+			ILI9341_POWER_SEQ_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_DTCA,
+			ili->conf->dtca,
+			ILI9341_DTCA_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_POWERA,
+			ili->conf->power_a,
+			ILI9341_POWER_A_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_PRC,
+			&ili->conf->prc,
+			1);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_DTCB,
+			ili->conf->dtcb,
+			ILI9341_DTCB_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_FRC,
+			ili->conf->frc,
+			ILI9341_FRC_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_DFC,
+			ili->conf->dfc_1,
+			ILI9341_DFC_1_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_POWER1,
+			&ili->conf->power_1,
+			1);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_POWER2,
+			&ili->conf->power_2,
+			1);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_VCOM1,
+			ili->conf->vcom_1,
+			ILI9341_VCOM_1_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_VCOM2,
+			&ili->conf->vcom_2,
+			1);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, MIPI_DCS_SET_ADDRESS_MODE,
+			&ili->conf->address_mode,
+			1);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_3GAMMA_EN,
+			&ili->conf->g3amma_en,
+			1);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_RGB_INTERFACE,
+			&ili->conf->rgb_interface,
+			1);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_DFC,
+			ili->conf->dfc_2,
+			ILI9341_DFC_2_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, MIPI_DCS_SET_COLUMN_ADDRESS,
+			ili->conf->column_addr,
+			ILI9341_COLUMN_ADDR_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, MIPI_DCS_SET_PAGE_ADDRESS,
+			ili->conf->page_addr,
+			ILI9341_PAGE_ADDR_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_INTERFACE,
+			ili->conf->interface,
+			ILI9341_INTERFACE_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, MIPI_DCS_SET_PIXEL_FORMAT,
+			&ili->conf->pixel_format,
+			1);
+	if (ret)
+		return ret;
+
+	ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START);
+	if (ret)
+		return ret;
+
+	msleep(200);
+	ret = _ili9341_command(ili, MIPI_DCS_SET_GAMMA_CURVE,
+			&ili->conf->gamma_curve,
+			1);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_PGAMMA,
+			ili->conf->pgamma,
+			ILI9341_PGAMMA_LEN);
+	if (ret)
+		return ret;
+
+	ret = _ili9341_command(ili, ILI9341_NGAMMA,
+			ili->conf->ngamma,
+			ILI9341_NGAMMA_LEN);
+	if (ret)
+		return ret;
+
+	ret = ili9341_command(ili, MIPI_DCS_EXIT_SLEEP_MODE);
+	if (ret)
+		return ret;
+
+	msleep(200);
+	ret = ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON);
+	if (ret)
+		return ret;
+
+	ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START);
+	if (ret)
+		return ret;
+
+
+	dev_info(ili->dev, "initialized display rgb interface\n");
+
+	return 0;
+}
+
+static int ili9341_dpi_power_on(struct ili9341 *ili)
+{
+	int ret = 0;
+
+	/* Assert RESET */
+	gpiod_set_value(ili->reset_gpio, 1);
+
+	/* Enable power */
+	if (!IS_ERR(ili->vcc)) {
+		ret = regulator_enable(ili->vcc);
+		if (ret < 0) {
+			dev_err(ili->dev, "unable to enable vcc\n");
+			return ret;
+		}
+	}
+	msleep(20);
+
+	/* De-assert RESET */
+	gpiod_set_value(ili->reset_gpio, 0);
+	msleep(10);
+
+	return 0;
+}
+
+static int ili9341_dpi_power_off(struct ili9341 *ili)
+{
+	/* Assert RESET */
+	gpiod_set_value(ili->reset_gpio, 1);
+
+	/* Disable power */
+	if (!IS_ERR(ili->vcc))
+		return regulator_disable(ili->vcc);
+
+	return 0;
+}
+
+static int ili9341_dpi_disable(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	ili9341_command(ili, MIPI_DCS_SET_DISPLAY_OFF);
+
+	return 0;
+}
+
+static int ili9341_dpi_unprepare(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	return ili9341_dpi_power_off(ili);
+}
+
+static int ili9341_dpi_prepare(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+	int ret;
+
+	ret = ili9341_dpi_power_on(ili);
+	if (ret < 0)
+		return ret;
+
+	ret = ili9341_dpi_init(ili);
+	if (ret < 0)
+		ili9341_dpi_unprepare(panel);
+
+	return ret;
+}
+
+static int ili9341_dpi_enable(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON);
+
+	return 0;
+}
+
+static int ili9341_dpi_get_modes(struct drm_panel *panel,
+				struct drm_connector *connector)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+	struct drm_device *drm = connector->dev;
+	struct drm_display_mode *mode;
+	struct drm_display_info *info;
+
+	info = &connector->display_info;
+	info->width_mm = ili->conf->mode.width_mm;
+	info->height_mm = ili->conf->mode.height_mm;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_DPL)
+		info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE;
+	else
+		info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_EPL)
+		info->bus_flags |= DRM_BUS_FLAG_DE_HIGH;
+	else
+		info->bus_flags |= DRM_BUS_FLAG_DE_LOW;
+
+	mode = drm_mode_duplicate(drm, &ili->conf->mode);
+	if (!mode) {
+		DRM_ERROR("bad mode or failed to add mode\n");
+		return -EINVAL;
+	}
+	drm_mode_set_name(mode);
+
+	/* Set up the polarity */
+	if (ili->conf->rgb_interface & ILI9341_RGB_HSPL)
+		mode->flags |= DRM_MODE_FLAG_PHSYNC;
+	else
+		mode->flags |= DRM_MODE_FLAG_NHSYNC;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_VSPL)
+		mode->flags |= DRM_MODE_FLAG_PVSYNC;
+	else
+		mode->flags |= DRM_MODE_FLAG_NVSYNC;
+
+	drm_mode_probed_add(connector, mode);
+
+	return 1; /* Number of modes */
+}
+
+static const struct drm_panel_funcs ili9341_dpi_funcs = {
+	.disable = ili9341_dpi_disable,
+	.unprepare = ili9341_dpi_unprepare,
+	.prepare = ili9341_dpi_prepare,
+	.enable = ili9341_dpi_enable,
+	.get_modes = ili9341_dpi_get_modes,
+};
+
+static int ili9341_dpi_probe(struct spi_device *spi)
+{
+	int ret;
+	struct device *dev = &spi->dev;
+	struct ili9341 *ili;
+
+	ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL);
+	if (!ili)
+		return -ENOMEM;
+
+	spi_set_drvdata(spi, ili);
+
+	ili->dev = dev;
+	/*
+	 * Every new incarnation of this display must have a unique
+	 * data entry for the system in this driver.
+	 */
+	ili->conf = of_device_get_match_data(dev);
+	if (!ili->conf) {
+		dev_err(dev, "missing device configuration\n");
+		return -ENODEV;
+	}
+
+	ili->vcc = devm_regulator_get_optional(dev, "vcc");
+	if (IS_ERR(ili->vcc))
+		dev_err(dev, "get optional vcc failed\n");
+
+	ili->reset_gpio = devm_gpiod_get_optional(dev, "reset",
+		GPIOD_OUT_HIGH);
+	if (IS_ERR(ili->reset_gpio)) {
+		dev_err(dev, "failed to get RESET GPIO\n");
+		return PTR_ERR(ili->reset_gpio);
+	}
+
+	ili->dc_gpio = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW);
+	if (IS_ERR(ili->dc_gpio)) {
+		dev_err(dev, "failed to get DC GPIO\n");
+		return PTR_ERR(ili->dc_gpio);
+	}
+
+	spi->bits_per_word = 8;
+	ret = spi_setup(spi);
+	if (ret < 0) {
+		dev_err(dev, "spi setup failed.\n");
+		return ret;
+	}
+
+	ili->max_spi_speed = ili->conf->max_spi_speed;
+
+	drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs,
+		       DRM_MODE_CONNECTOR_DPI);
+
+	return drm_panel_add(&ili->panel);
+}
+
+
+
+static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe,
+			     struct drm_crtc_state *crtc_state,
+			     struct drm_plane_state *plane_state)
+{
+	struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev);
+	struct mipi_dbi *dbi = &dbidev->dbi;
+	u8 addr_mode;
+	int ret, idx;
+
+	if (!drm_dev_enter(pipe->crtc.dev, &idx))
+		return;
+
+	DRM_DEBUG_KMS("\n");
+
+	ret = mipi_dbi_poweron_conditional_reset(dbidev);
+	if (ret < 0)
+		goto out_exit;
+	if (ret == 1)
+		goto out_enable;
+
+	mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
+
+	mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30);
+	mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81);
+	mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78);
+	mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02);
+	mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL);
+	mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00);
+
+	/* Power Control */
+	mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V);
+	mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT);
+	/* VCOM */
+	mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V,
+						ILI9341_DBI_VCOM_1_VML_1P5V);
+	mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58);
+
+	/* Memory Access Control */
+	mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT,
+				MIPI_DCS_PIXEL_FMT_16BIT);
+
+	/* Frame Rate */
+	mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03,
+						ILI9341_DBI_FRC_RTNA & 0x1f);
+
+	/* Gamma */
+	mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1);
+	mipi_dbi_command(dbi, ILI9341_PGAMMA,
+			 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1,
+			 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00);
+	mipi_dbi_command(dbi, ILI9341_NGAMMA,
+			 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1,
+			 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f);
+
+	/* DDRAM */
+	mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS |
+						ILI9341_DBI_EMS_DTS |
+						ILI9341_DBI_EMS_GON);
+
+	/* Display */
+	mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00);
+	mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+	msleep(100);
+
+	mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
+	msleep(100);
+
+out_enable:
+	switch (dbidev->rotation) {
+	default:
+		addr_mode = ILI9341_MADCTL_MX;
+		break;
+	case 90:
+		addr_mode = ILI9341_MADCTL_MV;
+		break;
+	case 180:
+		addr_mode = ILI9341_MADCTL_MY;
+		break;
+	case 270:
+		addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY |
+			    ILI9341_MADCTL_MX;
+		break;
+	}
+	addr_mode |= ILI9341_MADCTL_BGR;
+	mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
+	mipi_dbi_enable_flush(dbidev, crtc_state, plane_state);
+	DRM_DEBUG_KMS("initialized display serial interface\n");
+out_exit:
+	drm_dev_exit(idx);
+}
+
+static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = {
+	.enable = ili9341_dbi_enable,
+	.disable = mipi_dbi_pipe_disable,
+	.update = mipi_dbi_pipe_update,
+	.prepare_fb = drm_gem_fb_simple_display_pipe_prepare_fb,
+};
+
+static const struct drm_display_mode ili9341_dbi_mode = {
+	DRM_SIMPLE_MODE(240, 320, 37, 49),
+};
+
+DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops);
+
+static struct drm_driver ili9341_dbi_driver = {
+	.driver_features	= DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
+	.fops			= &ili9341_dbi_fops,
+	.release		= mipi_dbi_release,
+	DRM_GEM_CMA_VMAP_DRIVER_OPS,
+	.debugfs_init		= mipi_dbi_debugfs_init,
+	.name			= "ili9341",
+	.desc			= "Ilitek ILI9341",
+	.date			= "20180514",
+	.major			= 1,
+	.minor			= 0,
+};
+static int ili9341_dbi_probe(struct spi_device *spi)
+{
+	struct mipi_dbi_dev *dbidev;
+	struct drm_device *drm;
+	struct mipi_dbi *dbi;
+	struct gpio_desc *dc;
+	struct device *dev = &spi->dev;
+	u32 rotation = 0;
+	int ret;
+
+	dbidev = kzalloc(sizeof(*dbidev), GFP_KERNEL);
+	if (!dbidev)
+		return -ENOMEM;
+
+	dbi = &dbidev->dbi;
+	drm = &dbidev->drm;
+	ret = devm_drm_dev_init(dev, drm, &ili9341_dbi_driver);
+	if (ret) {
+		kfree(dbidev);
+		return ret;
+	}
+
+	drm_mode_config_init(drm);
+
+	dbi->reset = devm_gpiod_get_optional(dev, "reset",
+					GPIOD_OUT_HIGH);
+	if (IS_ERR(dbi->reset)) {
+		DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n");
+		return PTR_ERR(dbi->reset);
+	}
+
+	dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
+	if (IS_ERR(dc)) {
+		DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n");
+		return PTR_ERR(dc);
+	}
+
+	dbidev->regulator = devm_regulator_get_optional(dev, "vcc");
+	if (IS_ERR(dbidev->regulator))
+		dev_err(dev, "get optional vcc failed\n");
+
+	dbidev->backlight = devm_of_find_backlight(dev);
+	if (IS_ERR(dbidev->backlight))
+		return PTR_ERR(dbidev->backlight);
+
+	device_property_read_u32(dev, "rotation", &rotation);
+
+	ret = mipi_dbi_spi_init(spi, dbi, dc);
+	if (ret)
+		return ret;
+
+	ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs,
+					&ili9341_dbi_mode, rotation);
+	if (ret)
+		return ret;
+
+	drm_mode_config_reset(drm);
+
+	ret = drm_dev_register(drm, 0);
+	if (ret)
+		return ret;
+
+	spi_set_drvdata(spi, drm);
+
+	drm_fbdev_generic_setup(drm, 0);
+
+	return 0;
+}
+static int ili9341_probe(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+
+	if (!strcmp(id->name, "sf-tc240t-9370-t"))
+		return ili9341_dpi_probe(spi);
+	else if (!strcmp(id->name, "yx240qv29"))
+		return ili9341_dbi_probe(spi);
+
+	return -1;
+}
+
+static int ili9341_remove(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+	struct ili9341 *ili = spi_get_drvdata(spi);
+	struct drm_device *drm = spi_get_drvdata(spi);
+
+	if (!strcmp(id->name, "sf-tc240t-9370-t")) {
+		ili9341_dpi_power_off(ili);
+		drm_panel_remove(&ili->panel);
+	} else if (!strcmp(id->name, "yx240qv29")) {
+		drm_dev_unplug(drm);
+		drm_atomic_helper_shutdown(drm);
+	}
+	return 0;
+}
+
+static void ili9341_shutdown(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+
+	if (!strcmp(id->name, "yx240qv29"))
+		drm_atomic_helper_shutdown(spi_get_drvdata(spi));
+}
+
+static const struct of_device_id ili9341_of_match[] = {
+	{
+		.compatible = "st,sf-tc240t-9370-t",
+		.data = &ili9341_stm32f429_disco_data,
+	},
+	{
+		/* porting from tiny/ili9341.c
+		 * for original mipi dbi compitable
+		 */
+		.compatible = "adafruit,yx240qv29",
+		.data = NULL,
+	},
+};
+MODULE_DEVICE_TABLE(of, ili9341_of_match);
+
+static const struct spi_device_id ili9341_id[] = {
+	{ "yx240qv29", 0 },
+	{ "sf-tc240t-9370-t", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ili9341_id);
+
+static struct spi_driver ili9341_driver = {
+	.probe = ili9341_probe,
+	.remove = ili9341_remove,
+	.shutdown = ili9341_shutdown,
+	.id_table = ili9341_id,
+	.driver = {
+		.name = "panel-ilitek-ili9341",
+		.of_match_table = ili9341_of_match,
+	},
+};
+module_spi_driver(ili9341_driver);
+
+MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>");
+MODULE_DESCRIPTION("ILI9341 LCD panel driver");
+MODULE_LICENSE("GPL v2");