deleted file mode 100644
@@ -1,44 +0,0 @@
-Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface.
-
-Required properties:
-- compatible : "snps,dw-apb-ssi" or "mscc,<soc>-spi", where soc is "ocelot" or
- "jaguar2", or "amazon,alpine-dw-apb-ssi", or "snps,dwc-ssi-1.01a" or
- "intel,keembay-ssi"
-- reg : The register base for the controller. For "mscc,<soc>-spi", a second
- register set is required (named ICPU_CFG:SPI_MST)
-- interrupts : One interrupt, used by the controller.
-- #address-cells : <1>, as required by generic SPI binding.
-- #size-cells : <0>, also as required by generic SPI binding.
-- clocks : phandles for the clocks, see the description of clock-names below.
- The phandle for the "ssi_clk" is required. The phandle for the "pclk" clock
- is optional. If a single clock is specified but no clock-name, it is the
- "ssi_clk" clock. If both clocks are listed, the "ssi_clk" must be first.
-
-Optional properties:
-- clock-names : Contains the names of the clocks:
- "ssi_clk", for the core clock used to generate the external SPI clock.
- "pclk", the interface clock, required for register access. If a clock domain
- used to enable this clock then it should be named "pclk_clkdomain".
-- cs-gpios : Specifies the gpio pins to be used for chipselects.
-- num-cs : The number of chipselects. If omitted, this will default to 4.
-- reg-io-width : The I/O register width (in bytes) implemented by this
- device. Supported values are 2 or 4 (the default).
-- dmas : Phandle + identifiers of Tx and Rx DMA channels.
-- dma-names : Contains the names of the DMA channels. Must be "tx" and "rx".
-
-Child nodes as per the generic SPI binding.
-
-Example:
-
- spi@fff00000 {
- compatible = "snps,dw-apb-ssi";
- reg = <0xfff00000 0x1000>;
- interrupts = <0 154 4>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&spi_m_clk>;
- num-cs = <2>;
- cs-gpios = <&gpio0 13 0>,
- <&gpio0 14 0>;
- };
-
new file mode 100644
@@ -0,0 +1,127 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/snps,dw-apb-ssi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface
+
+maintainers:
+ - Mark Brown <broonie@kernel.org>
+
+allOf:
+ - $ref: "spi-controller.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - mscc,ocelot-spi
+ - mscc,jaguar2-spi
+ then:
+ properties:
+ reg:
+ minItems: 2
+
+properties:
+ compatible:
+ oneOf:
+ - description: Generic DW SPI Controller
+ enum:
+ - snps,dw-apb-ssi
+ - snps,dwc-ssi-1.01a
+ - description: Microsemi Ocelot/Jaguar2 SoC SPI Controller
+ items:
+ - enum:
+ - mscc,ocelot-spi
+ - mscc,jaguar2-spi
+ - const: snps,dw-apb-ssi
+ - description: Amazon Alpine SPI Controller
+ const: amazon,alpine-dw-apb-ssi
+ - description: Renesas RZ/N1 SPI Controller
+ items:
+ - const: renesas,rzn1-spi
+ - const: snps,dw-apb-ssi
+ - description: Intel Keem Bay SPI Controller
+ const: intel,keembay-ssi
+
+ reg:
+ minItems: 1
+ items:
+ - description: DW APB SSI controller memory mapped registers
+ - description: SPI MST region map
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 1
+ items:
+ - description: SPI Controller reference clock source
+ - description: APB interface clock source
+
+ clock-names:
+ minItems: 1
+ items:
+ - const: ssi_clk
+ - const: pclk
+
+ reg-io-width:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: I/O register width (in bytes) implemented by this device
+ default: 4
+ enum: [ 2, 4 ]
+
+ num-cs:
+ default: 4
+ minimum: 1
+ maximum: 4
+
+ dmas:
+ items:
+ - description: TX DMA Channel
+ - description: RX DMA Channel
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+
+patternProperties:
+ "^.*@[0-9a-f]+$":
+ type: object
+ properties:
+ reg:
+ minimum: 0
+ maximum: 3
+
+ spi-rx-bus-width:
+ const: 1
+
+ spi-tx-bus-width:
+ const: 1
+
+unevaluatedProperties: false
+
+required:
+ - compatible
+ - reg
+ - "#address-cells"
+ - "#size-cells"
+ - interrupts
+ - clocks
+
+examples:
+ - |
+ spi@fff00000 {
+ compatible = "snps,dw-apb-ssi";
+ reg = <0xfff00000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 154 4>;
+ clocks = <&spi_m_clk>;
+ num-cs = <2>;
+ cs-gpios = <&gpio0 13 0>,
+ <&gpio0 14 0>;
+ };
+...
deleted file mode 100644
@@ -1,24 +0,0 @@
-Synopsys DesignWare SPI master
-
-Required properties:
-- compatible: should be "snps,designware-spi"
-- #address-cells: see spi-bus.txt
-- #size-cells: see spi-bus.txt
-- reg: address and length of the spi master registers
-- interrupts: should contain one interrupt
-- clocks: spi clock phandle
-- num-cs: see spi-bus.txt
-
-Optional properties:
-- cs-gpios: see spi-bus.txt
-
-Example:
-
-spi: spi@4020a000 {
- compatible = "snps,designware-spi";
- interrupts = <11 1>;
- reg = <0x4020a000 0x1000>;
- clocks = <&pclk>;
- num-cs = <2>;
- cs-gpios = <&banka 0 0>;
-};