[105/131] mm: allow swappiness that prefers reclaiming anon over the file workingset

Commit Message

Andrew Morton June 3, 2020, 11:02 p.m. UTC

From: Johannes Weiner <[e-mail]>
Subject: mm: allow swappiness that prefers reclaiming anon over the file workingset

With the advent of fast random IO devices (SSDs, PMEM) and in-memory swap
devices such as zswap, it's possible for swap to be much faster than
filesystems, and for swapping to be preferable over thrashing filesystem
caches.

Allow setting swappiness - which defines the rough relative IO cost of
cache misses between page cache and swap-backed pages - to reflect such
situations by making the swap-preferred range configurable.

Link: http://lkml.kernel.org/r/[e-mail]
Signed-off-by: Johannes Weiner <[e-mail]>
Cc: Joonsoo Kim <[e-mail]>
Cc: Michal Hocko <[e-mail]>
Cc: Minchan Kim <[e-mail]>
Cc: Rik van Riel <[e-mail]>
Signed-off-by: Andrew Morton <[e-mail]>
---

 Documentation/admin-guide/sysctl/vm.rst |   23 +++++++++++++++++-----
 kernel/sysctl.c                         |    3 +-
 mm/vmscan.c                             |    2 -
 3 files changed, 21 insertions(+), 7 deletions(-)

Patch

--- a/Documentation/admin-guide/sysctl/vm.rst~mm-allow-swappiness-that-prefers-reclaiming-anon-over-the-file-workingset
+++ a/Documentation/admin-guide/sysctl/vm.rst
@@ -831,14 +831,27 @@  tooling to work, you can do::
 swappiness
 ==========
 
-This control is used to define how aggressive the kernel will swap
-memory pages.  Higher values will increase aggressiveness, lower values
-decrease the amount of swap.  A value of 0 instructs the kernel not to
-initiate swap until the amount of free and file-backed pages is less
-than the high water mark in a zone.
+This control is used to define the rough relative IO cost of swapping
+and filesystem paging, as a value between 0 and 200. At 100, the VM
+assumes equal IO cost and will thus apply memory pressure to the page
+cache and swap-backed pages equally; lower values signify more
+expensive swap IO, higher values indicates cheaper.
+
+Keep in mind that filesystem IO patterns under memory pressure tend to
+be more efficient than swap's random IO. An optimal value will require
+experimentation and will also be workload-dependent.
 
 The default value is 60.
 
+For in-memory swap, like zram or zswap, as well as hybrid setups that
+have swap on faster devices than the filesystem, values beyond 100 can
+be considered. For example, if the random IO against the swap device
+is on average 2x faster than IO from the filesystem, swappiness should
+be 133 (x + 2x = 200, 2x = 133.33).
+
+At 0, the kernel will not initiate swap until the amount of free and
+file-backed pages is less than the high watermark in a zone.
+
 
 unprivileged_userfaultfd
 ========================
--- a/kernel/sysctl.c~mm-allow-swappiness-that-prefers-reclaiming-anon-over-the-file-workingset
+++ a/kernel/sysctl.c
@@ -131,6 +131,7 @@  static unsigned long zero_ul;
 static unsigned long one_ul = 1;
 static unsigned long long_max = LONG_MAX;
 static int one_hundred = 100;
+static int two_hundred = 200;
 static int one_thousand = 1000;
 #ifdef CONFIG_PRINTK
 static int ten_thousand = 10000;
@@ -1391,7 +1392,7 @@  static struct ctl_table vm_table[] = {
 		.mode		= 0644,
 		.proc_handler	= proc_dointvec_minmax,
 		.extra1		= SYSCTL_ZERO,
-		.extra2		= &one_hundred,
+		.extra2		= &two_hundred,
 	},
 #ifdef CONFIG_HUGETLB_PAGE
 	{
--- a/mm/vmscan.c~mm-allow-swappiness-that-prefers-reclaiming-anon-over-the-file-workingset
+++ a/mm/vmscan.c
@@ -161,7 +161,7 @@  struct scan_control {
 #endif
 
 /*
- * From 0 .. 100.  Higher means more swappy.
+ * From 0 .. 200.  Higher means more swappy.
  */
 int vm_swappiness = 60;
 /*