| Message ID | 1592300467-29196-1-git-send-email-krzk@kernel.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v3,1/2] spi: spi-fsl-dspi: Fix external abort on interrupt in resume or exit paths | expand |
Hi Krzysztof, On Tue, 16 Jun 2020 at 12:42, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > If shared interrupt comes late, during probe error path or device remove > (could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler > dspi_interrupt() will access registers with the clock being disabled. > This leads to external abort on non-linefetch on Toradex Colibri VF50 > module (with Vybrid VF5xx): > > $ echo 4002d000.spi > /sys/devices/platform/soc/40000000.bus/4002d000.spi/driver/unbind > > Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c > Internal error: : 1008 [#1] ARM > Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree) > Backtrace: > (regmap_mmio_read32le) > (regmap_mmio_read) > (_regmap_bus_reg_read) > (_regmap_read) > (regmap_read) > (dspi_interrupt) > (free_irq) > (devm_irq_release) > (release_nodes) > (devres_release_all) > (device_release_driver_internal) > > The resource-managed framework should not be used for shared interrupt > handling, because the interrupt handler might be called after releasing > other resources and disabling clocks. > > Similar bug could happen during suspend - the shared interrupt handler > could be invoked after suspending the device. Each device sharing this > interrupt line should disable the IRQ during suspend so handler will be > invoked only in following cases: > 1. None suspended, > 2. All devices resumed. > > Fixes: 349ad66c0ab0 ("spi:Add Freescale DSPI driver for Vybrid VF610 platform") > Cc: <stable@vger.kernel.org> > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > > --- > > Changes since v2: > 1. Go back to v1 and use non-devm interface, > 2. Fix also suspend/resume paths. > > Changes since v1: > 1. Disable the IRQ instead of using non-devm interface. > --- > drivers/spi/spi-fsl-dspi.c | 17 +++++++++++++---- > 1 file changed, 13 insertions(+), 4 deletions(-) > > diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c > index 58190c94561f..7ecc90ec8f2f 100644 > --- a/drivers/spi/spi-fsl-dspi.c > +++ b/drivers/spi/spi-fsl-dspi.c > @@ -1109,6 +1109,8 @@ static int dspi_suspend(struct device *dev) > struct spi_controller *ctlr = dev_get_drvdata(dev); > struct fsl_dspi *dspi = spi_controller_get_devdata(ctlr); > > + if (dspi->irq > 0) Since the line right above "goto poll_mode" is executing "dspi->irq = 0;" on error, all these checks could have been simplified as "if (dspi->irq)" which is slightly easier on the eye. > + disable_irq(dspi->irq); > spi_controller_suspend(ctlr); > clk_disable_unprepare(dspi->clk); > > @@ -1129,6 +1131,8 @@ static int dspi_resume(struct device *dev) > if (ret) > return ret; > spi_controller_resume(ctlr); > + if (dspi->irq > 0) > + enable_irq(dspi->irq); > > return 0; > } > @@ -1385,8 +1389,8 @@ static int dspi_probe(struct platform_device *pdev) > goto poll_mode; > } > > - ret = devm_request_irq(&pdev->dev, dspi->irq, dspi_interrupt, > - IRQF_SHARED, pdev->name, dspi); > + ret = request_threaded_irq(dspi->irq, dspi_interrupt, NULL, > + IRQF_SHARED, pdev->name, dspi); > if (ret < 0) { > dev_err(&pdev->dev, "Unable to attach DSPI interrupt\n"); > goto out_clk_put; > @@ -1400,7 +1404,7 @@ static int dspi_probe(struct platform_device *pdev) > ret = dspi_request_dma(dspi, res->start); > if (ret < 0) { > dev_err(&pdev->dev, "can't get dma channels\n"); > - goto out_clk_put; > + goto out_free_irq; > } > } > > @@ -1415,11 +1419,14 @@ static int dspi_probe(struct platform_device *pdev) > ret = spi_register_controller(ctlr); > if (ret != 0) { > dev_err(&pdev->dev, "Problem registering DSPI ctlr\n"); > - goto out_clk_put; > + goto out_free_irq; > } > > return ret; > > +out_free_irq: > + if (dspi->irq > 0) > + free_irq(dspi->irq, dspi); > out_clk_put: > clk_disable_unprepare(dspi->clk); > out_ctlr_put: > @@ -1435,6 +1442,8 @@ static int dspi_remove(struct platform_device *pdev) > > /* Disconnect from the SPI framework */ > dspi_release_dma(dspi); > + if (dspi->irq > 0) > + free_irq(dspi->irq, dspi); There is a subtle but important bug here: by waiting for the current interrupt to finish and removing the handler, you are effectively causing dspi_transfer_one_message to deadlock. The way this driver works (and I'm sure many others) is that it transmits a SPI buffer through a train of interrupts: each completion of a chunk triggers the transmission of the next one, which will eventually raise an IRQ and the process continues. But if you just disable the IRQ like that, you effectively chop the interrupt train in the middle, and dspi_transfer_one_message will remain stuck in wait_for_completion(&dspi->xfer_done). The reason why you don't do this (while I very much do) is that you seem to be on Vybrid which uses DMA mode, and for DMA, the DSPI interrupt line doesn't really do much of anything at all (which makes it a bit funny that you're spending so much time working on it). Instead, the completion events go from the DSPI controller directly to the DMA controller, requesting for more data, and that's where IRQs are raised to the CPU. So, to avoid this deadlock, I would suggest you move spi_unregister_controller as the first thing that gets called in the teardown process. And yes, this should be a bugfix patch in itself. And while I'm at it, let me add another one: this recent commit: commit dc234825997ec6ff05980ca9e2204f4ac3f8d695 Author: Peng Ma <peng.ma@nxp.com> Date: Fri Apr 24 14:12:16 2020 +0800 spi: spi-fsl-dspi: Adding shutdown hook We need to ensure dspi controller could be stopped in order for kexec to start the next kernel. So add the shutdown operation support. Signed-off-by: Peng Ma <peng.ma@nxp.com> Link: https://lore.kernel.org/r/20200424061216.27445-1-peng.ma@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> is causing some very similar issues: if you look at the code it adds, it disables the FIFOs and halts the module, which is bad for the same reason that it will hang an ongoing interrupt train in dspi_transfer_one_message: [17159.264026] INFO: task init:1870 blocked for more than 120 seconds. [17159.270385] Not tainted 5.8.0-rc1-00133-g923e4b5032dd-dirty #208 [17159.276953] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [17159.284828] init D 0 1870 1 0x00000008 [17159.290353] Call trace: [17159.292828] __switch_to+0x108/0x158 [17159.296433] __schedule+0x320/0x870 [17159.299933] schedule+0x50/0x110 [17159.303188] schedule_timeout+0x35c/0x438 [17159.307229] wait_for_completion+0xb0/0x148 [17159.311444] dspi_transfer_one_message+0x8c/0x4d0 [17159.316180] __spi_pump_messages+0x434/0x9a8 [17159.320480] __spi_sync+0x2ec/0x3a8 [17159.323994] spi_sync+0x3c/0x60 [17159.327149] spi_sync_transfer+0x94/0xb8 [17159.331101] sja1105_xfer.isra.0+0x26c/0x2f8 [17159.335402] sja1105_xfer_buf+0x20/0x30 [17159.339267] sja1105_dynamic_config_write+0x18c/0x1e0 [17159.344353] sja1105_bridge_stp_state_set+0x58/0xd0 [17159.349265] dsa_port_set_state+0x74/0xd0 [17159.353303] dsa_port_set_state_now+0x28/0x58 [17159.357690] dsa_port_disable_rt+0x74/0x78 [17159.361818] dsa_slave_close+0x2c/0xd0 [17159.365601] __dev_close_many+0xcc/0x150 [17159.369553] dev_close_many+0x8c/0x130 [17159.373330] rollback_registered_many+0x128/0x550 [17159.378066] unregister_netdevice_queue+0x98/0x120 [17159.382891] unregister_netdev+0x2c/0x40 [17159.386843] dsa_slave_destroy+0x4c/0x80 [17159.390795] dsa_port_teardown+0xa0/0xd0 [17159.394746] dsa_tree_teardown_switches+0x40/0x98 [17159.399481] dsa_unregister_switch+0xbc/0x170 [17159.403868] sja1105_remove+0x20/0x30 [17159.407557] spi_drv_remove+0x34/0x58 [17159.411247] device_release_driver_internal+0x104/0x1d8 [17159.416506] device_release_driver+0x20/0x30 [17159.420808] bus_remove_device+0xdc/0x168 [17159.424847] device_del+0x15c/0x3b0 [17159.428363] device_unregister+0x28/0x80 [17159.432313] spi_unregister_device+0x8c/0xb0 [17159.436613] __unregister+0x18/0x28 [17159.440130] device_for_each_child+0x64/0xb0 [17159.444430] spi_unregister_controller+0x44/0x140 [17159.449168] dspi_shutdown+0x88/0x98 [17159.452770] platform_drv_shutdown+0x28/0x38 [17159.457072] device_shutdown+0x168/0x340 [17159.461024] kernel_restart_prepare+0x40/0x50 [17159.465416] kernel_restart+0x20/0x70 [17159.469107] __do_sys_reboot+0x22c/0x258 [17159.473058] __arm64_sys_reboot+0x2c/0x38 [17159.477098] el0_svc_common.constprop.0+0x7c/0x180 [17159.481921] do_el0_svc+0x2c/0x98 [17159.485261] el0_sync_handler+0x9c/0x1b8 [17159.489213] el0_sync+0x158/0x180 [17159.492556] INFO: lockdep is turned off. [17159.496508] Kernel panic - not syncing: hung_task: blocked tasks [17159.502537] CPU: 1 PID: 25 Comm: khungtaskd Not tainted 5.8.0-rc1-00133-g923e4b5032dd-dirty #208 [17159.516767] Call trace: [17159.519218] dump_backtrace+0x0/0x1e0 [17159.522889] show_stack+0x20/0x30 [17159.526214] dump_stack+0xec/0x158 [17159.529624] panic+0x16c/0x37c [17159.532686] watchdog+0x3d8/0x7f8 [17159.536008] kthread+0x158/0x168 [17159.539245] ret_from_fork+0x10/0x1c [17159.542844] Kernel Offset: 0x5bd125880000 from 0xffff800010000000 [17159.548957] PHYS_OFFSET: 0xffffafdb00000000 [17159.553151] CPU features: 0x240022,21806008 [17159.557346] Memory Limit: none [17159.560414] Rebooting in 3 seconds.. So for this third issue, what I would suggest would be to merge dspi_shutdown with the reworked version of dspi_remove (i.e. to move "/* Disable RX and TX */" and "/* Stop Running */" to dspi_remove, right before clk_disable_unprepare, and then just call dspi_remove from dspi_shutdown. It would end up looking like this: static int dspi_remove(struct platform_device *pdev) { struct spi_controller *ctlr = platform_get_drvdata(pdev); struct fsl_dspi *dspi = spi_controller_get_devdata(ctlr); /* Disconnect from the SPI framework */ spi_unregister_controller(dspi->ctlr); dspi_release_dma(dspi); if (dspi->irq > 0) free_irq(dspi->irq, dspi); /* Disable RX and TX */ regmap_update_bits(dspi->regmap, SPI_MCR, SPI_MCR_DIS_TXF | SPI_MCR_DIS_RXF, SPI_MCR_DIS_TXF | SPI_MCR_DIS_RXF); /* Stop Running */ regmap_update_bits(dspi->regmap, SPI_MCR, SPI_MCR_HALT, SPI_MCR_HALT); clk_disable_unprepare(dspi->clk); return 0; } static void dspi_shutdown(struct platform_device *pdev) { dspi_remove(pdev); } If you think it's too complicated or that you can't test, let me know and I can take over the patch series. > clk_disable_unprepare(dspi->clk); > spi_unregister_controller(dspi->ctlr); > > -- > 2.7.4 > Thanks, -Vladimir
On Fri, Jun 19, 2020 at 12:24:56AM +0300, Vladimir Oltean wrote: > Hi Krzysztof, > > On Tue, 16 Jun 2020 at 12:42, Krzysztof Kozlowski <krzk@kernel.org> wrote: > > > > If shared interrupt comes late, during probe error path or device remove > > (could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler > > dspi_interrupt() will access registers with the clock being disabled. > > This leads to external abort on non-linefetch on Toradex Colibri VF50 > > module (with Vybrid VF5xx): > > > > $ echo 4002d000.spi > /sys/devices/platform/soc/40000000.bus/4002d000.spi/driver/unbind > > > > Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c > > Internal error: : 1008 [#1] ARM > > Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree) > > Backtrace: > > (regmap_mmio_read32le) > > (regmap_mmio_read) > > (_regmap_bus_reg_read) > > (_regmap_read) > > (regmap_read) > > (dspi_interrupt) > > (free_irq) > > (devm_irq_release) > > (release_nodes) > > (devres_release_all) > > (device_release_driver_internal) > > > > The resource-managed framework should not be used for shared interrupt > > handling, because the interrupt handler might be called after releasing > > other resources and disabling clocks. > > > > Similar bug could happen during suspend - the shared interrupt handler > > could be invoked after suspending the device. Each device sharing this > > interrupt line should disable the IRQ during suspend so handler will be > > invoked only in following cases: > > 1. None suspended, > > 2. All devices resumed. > > > > Fixes: 349ad66c0ab0 ("spi:Add Freescale DSPI driver for Vybrid VF610 platform") > > Cc: <stable@vger.kernel.org> > > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > > > > --- > > > > Changes since v2: > > 1. Go back to v1 and use non-devm interface, > > 2. Fix also suspend/resume paths. > > > > Changes since v1: > > 1. Disable the IRQ instead of using non-devm interface. > > --- > > drivers/spi/spi-fsl-dspi.c | 17 +++++++++++++---- > > 1 file changed, 13 insertions(+), 4 deletions(-) > > > > diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c > > index 58190c94561f..7ecc90ec8f2f 100644 > > --- a/drivers/spi/spi-fsl-dspi.c > > +++ b/drivers/spi/spi-fsl-dspi.c > > @@ -1109,6 +1109,8 @@ static int dspi_suspend(struct device *dev) > > struct spi_controller *ctlr = dev_get_drvdata(dev); > > struct fsl_dspi *dspi = spi_controller_get_devdata(ctlr); > > > > + if (dspi->irq > 0) > > Since the line right above "goto poll_mode" is executing "dspi->irq = > 0;" on error, all these checks could have been simplified as "if > (dspi->irq)" which is slightly easier on the eye. Indeed. > > > > + disable_irq(dspi->irq); > > spi_controller_suspend(ctlr); > > clk_disable_unprepare(dspi->clk); > > > > @@ -1129,6 +1131,8 @@ static int dspi_resume(struct device *dev) > > if (ret) > > return ret; > > spi_controller_resume(ctlr); > > + if (dspi->irq > 0) > > + enable_irq(dspi->irq); > > > > return 0; > > } > > @@ -1385,8 +1389,8 @@ static int dspi_probe(struct platform_device *pdev) > > goto poll_mode; > > } > > > > - ret = devm_request_irq(&pdev->dev, dspi->irq, dspi_interrupt, > > - IRQF_SHARED, pdev->name, dspi); > > + ret = request_threaded_irq(dspi->irq, dspi_interrupt, NULL, > > + IRQF_SHARED, pdev->name, dspi); > > if (ret < 0) { > > dev_err(&pdev->dev, "Unable to attach DSPI interrupt\n"); > > goto out_clk_put; > > @@ -1400,7 +1404,7 @@ static int dspi_probe(struct platform_device *pdev) > > ret = dspi_request_dma(dspi, res->start); > > if (ret < 0) { > > dev_err(&pdev->dev, "can't get dma channels\n"); > > - goto out_clk_put; > > + goto out_free_irq; > > } > > } > > > > @@ -1415,11 +1419,14 @@ static int dspi_probe(struct platform_device *pdev) > > ret = spi_register_controller(ctlr); > > if (ret != 0) { > > dev_err(&pdev->dev, "Problem registering DSPI ctlr\n"); > > - goto out_clk_put; > > + goto out_free_irq; > > } > > > > return ret; > > > > +out_free_irq: > > + if (dspi->irq > 0) > > + free_irq(dspi->irq, dspi); > > out_clk_put: > > clk_disable_unprepare(dspi->clk); > > out_ctlr_put: > > @@ -1435,6 +1442,8 @@ static int dspi_remove(struct platform_device *pdev) > > > > /* Disconnect from the SPI framework */ > > dspi_release_dma(dspi); > > + if (dspi->irq > 0) > > + free_irq(dspi->irq, dspi); > > There is a subtle but important bug here: by waiting for the current > interrupt to finish and removing the handler, you are effectively > causing dspi_transfer_one_message to deadlock. The way this driver > works (and I'm sure many others) is that it transmits a SPI buffer > through a train of interrupts: each completion of a chunk triggers the > transmission of the next one, which will eventually raise an IRQ and > the process continues. But if you just disable the IRQ like that, you > effectively chop the interrupt train in the middle, and > dspi_transfer_one_message will remain stuck in > wait_for_completion(&dspi->xfer_done). > The reason why you don't do this (while I very much do) is that you > seem to be on Vybrid which uses DMA mode, and for DMA, the DSPI > interrupt line doesn't really do much of anything at all (which makes > it a bit funny that you're spending so much time working on it). > Instead, the completion events go from the DSPI controller directly to > the DMA controller, requesting for more data, and that's where IRQs > are raised to the CPU. > So, to avoid this deadlock, I would suggest you move > spi_unregister_controller as the first thing that gets called in the > teardown process. And yes, this should be a bugfix patch in itself. You're right. It also makes sense from the reverse-probe-order point of view. > > And while I'm at it, let me add another one: this recent commit: > > commit dc234825997ec6ff05980ca9e2204f4ac3f8d695 > Author: Peng Ma <peng.ma@nxp.com> > Date: Fri Apr 24 14:12:16 2020 +0800 > > spi: spi-fsl-dspi: Adding shutdown hook > > We need to ensure dspi controller could be stopped in order for kexec > to start the next kernel. > So add the shutdown operation support. > > Signed-off-by: Peng Ma <peng.ma@nxp.com> > Link: https://lore.kernel.org/r/20200424061216.27445-1-peng.ma@nxp.com > Signed-off-by: Mark Brown <broonie@kernel.org> > > is causing some very similar issues: if you look at the code it adds, > it disables the FIFOs and halts the module, which is bad for the same > reason that it will hang an ongoing interrupt train in > dspi_transfer_one_message: > > [17159.264026] INFO: task init:1870 blocked for more than 120 seconds. > [17159.270385] Not tainted 5.8.0-rc1-00133-g923e4b5032dd-dirty #208 > [17159.276953] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" > disables this message. > [17159.284828] init D 0 1870 1 0x00000008 > [17159.290353] Call trace: > [17159.292828] __switch_to+0x108/0x158 > [17159.296433] __schedule+0x320/0x870 > [17159.299933] schedule+0x50/0x110 > [17159.303188] schedule_timeout+0x35c/0x438 > [17159.307229] wait_for_completion+0xb0/0x148 > [17159.311444] dspi_transfer_one_message+0x8c/0x4d0 > [17159.316180] __spi_pump_messages+0x434/0x9a8 > [17159.320480] __spi_sync+0x2ec/0x3a8 > [17159.323994] spi_sync+0x3c/0x60 > [17159.327149] spi_sync_transfer+0x94/0xb8 > [17159.331101] sja1105_xfer.isra.0+0x26c/0x2f8 > [17159.335402] sja1105_xfer_buf+0x20/0x30 > [17159.339267] sja1105_dynamic_config_write+0x18c/0x1e0 > [17159.344353] sja1105_bridge_stp_state_set+0x58/0xd0 > [17159.349265] dsa_port_set_state+0x74/0xd0 > [17159.353303] dsa_port_set_state_now+0x28/0x58 > [17159.357690] dsa_port_disable_rt+0x74/0x78 > [17159.361818] dsa_slave_close+0x2c/0xd0 > [17159.365601] __dev_close_many+0xcc/0x150 > [17159.369553] dev_close_many+0x8c/0x130 > [17159.373330] rollback_registered_many+0x128/0x550 > [17159.378066] unregister_netdevice_queue+0x98/0x120 > [17159.382891] unregister_netdev+0x2c/0x40 > [17159.386843] dsa_slave_destroy+0x4c/0x80 > [17159.390795] dsa_port_teardown+0xa0/0xd0 > [17159.394746] dsa_tree_teardown_switches+0x40/0x98 > [17159.399481] dsa_unregister_switch+0xbc/0x170 > [17159.403868] sja1105_remove+0x20/0x30 > [17159.407557] spi_drv_remove+0x34/0x58 > [17159.411247] device_release_driver_internal+0x104/0x1d8 > [17159.416506] device_release_driver+0x20/0x30 > [17159.420808] bus_remove_device+0xdc/0x168 > [17159.424847] device_del+0x15c/0x3b0 > [17159.428363] device_unregister+0x28/0x80 > [17159.432313] spi_unregister_device+0x8c/0xb0 > [17159.436613] __unregister+0x18/0x28 > [17159.440130] device_for_each_child+0x64/0xb0 > [17159.444430] spi_unregister_controller+0x44/0x140 > [17159.449168] dspi_shutdown+0x88/0x98 > [17159.452770] platform_drv_shutdown+0x28/0x38 > [17159.457072] device_shutdown+0x168/0x340 > [17159.461024] kernel_restart_prepare+0x40/0x50 > [17159.465416] kernel_restart+0x20/0x70 > [17159.469107] __do_sys_reboot+0x22c/0x258 > [17159.473058] __arm64_sys_reboot+0x2c/0x38 > [17159.477098] el0_svc_common.constprop.0+0x7c/0x180 > [17159.481921] do_el0_svc+0x2c/0x98 > [17159.485261] el0_sync_handler+0x9c/0x1b8 > [17159.489213] el0_sync+0x158/0x180 > [17159.492556] INFO: lockdep is turned off. > [17159.496508] Kernel panic - not syncing: hung_task: blocked tasks > [17159.502537] CPU: 1 PID: 25 Comm: khungtaskd Not tainted > 5.8.0-rc1-00133-g923e4b5032dd-dirty #208 > [17159.516767] Call trace: > [17159.519218] dump_backtrace+0x0/0x1e0 > [17159.522889] show_stack+0x20/0x30 > [17159.526214] dump_stack+0xec/0x158 > [17159.529624] panic+0x16c/0x37c > [17159.532686] watchdog+0x3d8/0x7f8 > [17159.536008] kthread+0x158/0x168 > [17159.539245] ret_from_fork+0x10/0x1c > [17159.542844] Kernel Offset: 0x5bd125880000 from 0xffff800010000000 > [17159.548957] PHYS_OFFSET: 0xffffafdb00000000 > [17159.553151] CPU features: 0x240022,21806008 > [17159.557346] Memory Limit: none > [17159.560414] Rebooting in 3 seconds.. > > So for this third issue, what I would suggest would be to merge > dspi_shutdown with the reworked version of dspi_remove (i.e. to move > "/* Disable RX and TX */" and "/* Stop Running */" to dspi_remove, > right before clk_disable_unprepare, and then just call dspi_remove > from dspi_shutdown. It would end up looking like this: > > static int dspi_remove(struct platform_device *pdev) > { > struct spi_controller *ctlr = platform_get_drvdata(pdev); > struct fsl_dspi *dspi = spi_controller_get_devdata(ctlr); > > /* Disconnect from the SPI framework */ > spi_unregister_controller(dspi->ctlr); > > dspi_release_dma(dspi); > if (dspi->irq > 0) > free_irq(dspi->irq, dspi); > > /* Disable RX and TX */ > regmap_update_bits(dspi->regmap, SPI_MCR, > SPI_MCR_DIS_TXF | SPI_MCR_DIS_RXF, > SPI_MCR_DIS_TXF | SPI_MCR_DIS_RXF); > > /* Stop Running */ > regmap_update_bits(dspi->regmap, SPI_MCR, SPI_MCR_HALT, SPI_MCR_HALT); > > clk_disable_unprepare(dspi->clk); > > return 0; > } > > static void dspi_shutdown(struct platform_device *pdev) > { > dspi_remove(pdev); > } Yes, good point. The shutdown also lacks the interrupt freeing in my patch. Best regards, Krzysztof > > If you think it's too complicated or that you can't test, let me know > and I can take over the patch series. > > > clk_disable_unprepare(dspi->clk); > > spi_unregister_controller(dspi->ctlr); > > > > -- > > 2.7.4 > > > > Thanks, > -Vladimir
diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c index 58190c94561f..7ecc90ec8f2f 100644 --- a/drivers/spi/spi-fsl-dspi.c +++ b/drivers/spi/spi-fsl-dspi.c @@ -1109,6 +1109,8 @@ static int dspi_suspend(struct device *dev) struct spi_controller *ctlr = dev_get_drvdata(dev); struct fsl_dspi *dspi = spi_controller_get_devdata(ctlr); + if (dspi->irq > 0) + disable_irq(dspi->irq); spi_controller_suspend(ctlr); clk_disable_unprepare(dspi->clk); @@ -1129,6 +1131,8 @@ static int dspi_resume(struct device *dev) if (ret) return ret; spi_controller_resume(ctlr); + if (dspi->irq > 0) + enable_irq(dspi->irq); return 0; } @@ -1385,8 +1389,8 @@ static int dspi_probe(struct platform_device *pdev) goto poll_mode; } - ret = devm_request_irq(&pdev->dev, dspi->irq, dspi_interrupt, - IRQF_SHARED, pdev->name, dspi); + ret = request_threaded_irq(dspi->irq, dspi_interrupt, NULL, + IRQF_SHARED, pdev->name, dspi); if (ret < 0) { dev_err(&pdev->dev, "Unable to attach DSPI interrupt\n"); goto out_clk_put; @@ -1400,7 +1404,7 @@ static int dspi_probe(struct platform_device *pdev) ret = dspi_request_dma(dspi, res->start); if (ret < 0) { dev_err(&pdev->dev, "can't get dma channels\n"); - goto out_clk_put; + goto out_free_irq; } } @@ -1415,11 +1419,14 @@ static int dspi_probe(struct platform_device *pdev) ret = spi_register_controller(ctlr); if (ret != 0) { dev_err(&pdev->dev, "Problem registering DSPI ctlr\n"); - goto out_clk_put; + goto out_free_irq; } return ret; +out_free_irq: + if (dspi->irq > 0) + free_irq(dspi->irq, dspi); out_clk_put: clk_disable_unprepare(dspi->clk); out_ctlr_put: @@ -1435,6 +1442,8 @@ static int dspi_remove(struct platform_device *pdev) /* Disconnect from the SPI framework */ dspi_release_dma(dspi); + if (dspi->irq > 0) + free_irq(dspi->irq, dspi); clk_disable_unprepare(dspi->clk); spi_unregister_controller(dspi->ctlr);
If shared interrupt comes late, during probe error path or device remove (could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler dspi_interrupt() will access registers with the clock being disabled. This leads to external abort on non-linefetch on Toradex Colibri VF50 module (with Vybrid VF5xx): $ echo 4002d000.spi > /sys/devices/platform/soc/40000000.bus/4002d000.spi/driver/unbind Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c Internal error: : 1008 [#1] ARM Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree) Backtrace: (regmap_mmio_read32le) (regmap_mmio_read) (_regmap_bus_reg_read) (_regmap_read) (regmap_read) (dspi_interrupt) (free_irq) (devm_irq_release) (release_nodes) (devres_release_all) (device_release_driver_internal) The resource-managed framework should not be used for shared interrupt handling, because the interrupt handler might be called after releasing other resources and disabling clocks. Similar bug could happen during suspend - the shared interrupt handler could be invoked after suspending the device. Each device sharing this interrupt line should disable the IRQ during suspend so handler will be invoked only in following cases: 1. None suspended, 2. All devices resumed. Fixes: 349ad66c0ab0 ("spi:Add Freescale DSPI driver for Vybrid VF610 platform") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> --- Changes since v2: 1. Go back to v1 and use non-devm interface, 2. Fix also suspend/resume paths. Changes since v1: 1. Disable the IRQ instead of using non-devm interface. --- drivers/spi/spi-fsl-dspi.c | 17 +++++++++++++---- 1 file changed, 13 insertions(+), 4 deletions(-)