@@ -15,37 +15,11 @@
#include <mach/map.h>
-/*
- * cannot use commonly <plat/uncompress.h>
- * because uart base of S5P6440 and S5P6450 is different
- */
-
-typedef unsigned int upf_t; /* cannot include linux/serial_core.h */
-
-/* uart setup */
-
-unsigned int fifo_mask;
-unsigned int fifo_max;
-
-/* forward declerations */
-
-static void arch_detect_cpu(void);
-
-/* defines for UART registers */
-
-#include <plat/regs-serial.h>
-#include <plat/regs-watchdog.h>
-
-/* working in physical space... */
-#undef S3C2410_WDOGREG
-#define S3C2410_WDOGREG(x) ((S3C24XX_PA_WATCHDOG + (x)))
-
-/* how many bytes we allow into the FIFO at a time in FIFO mode */
-#define FIFO_MAX (14)
-
unsigned long uart_base;
-static __inline__ void get_uart_base(void)
+#include <plat/uncompress.h>
+
+static void arch_detect_cpu(void)
{
unsigned int chipid;
@@ -57,128 +31,9 @@ static __inline__ void get_uart_base(void)
uart_base += 0xEC800000;
else
uart_base += 0xEC000000;
-}
-
-static __inline__ void uart_wr(unsigned int reg, unsigned int val)
-{
- volatile unsigned int *ptr;
- get_uart_base();
- ptr = (volatile unsigned int *)(reg + uart_base);
- *ptr = val;
-}
-
-static __inline__ unsigned int uart_rd(unsigned int reg)
-{
- volatile unsigned int *ptr;
-
- get_uart_base();
- ptr = (volatile unsigned int *)(reg + uart_base);
- return *ptr;
-}
-
-/*
- * we can deal with the case the UARTs are being run
- * in FIFO mode, so that we don't hold up our execution
- * waiting for tx to happen...
- */
-
-static void putc(int ch)
-{
- if (uart_rd(S3C2410_UFCON) & S3C2410_UFCON_FIFOMODE) {
- int level;
-
- while (1) {
- level = uart_rd(S3C2410_UFSTAT);
- level &= fifo_mask;
-
- if (level < fifo_max)
- break;
- }
-
- } else {
- /* not using fifos */
-
- while ((uart_rd(S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE) != S3C2410_UTRSTAT_TXE)
- barrier();
- }
-
- /* write byte to transmission register */
- uart_wr(S3C2410_UTXH, ch);
-}
-
-static inline void flush(void)
-{
-}
-
-#define __raw_writel(d, ad) \
- do { \
- *((volatile unsigned int __force *)(ad)) = (d); \
- } while (0)
-
-
-#ifdef CONFIG_S3C_BOOT_ERROR_RESET
-
-static void arch_decomp_error(const char *x)
-{
- putstr("\n\n");
- putstr(x);
- putstr("\n\n -- System resetting\n");
-
- __raw_writel(0x4000, S3C2410_WTDAT);
- __raw_writel(0x4000, S3C2410_WTCNT);
- __raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x40), S3C2410_WTCON);
-
- while(1);
-}
-
-#define arch_error arch_decomp_error
-#endif
-
-#ifdef CONFIG_S3C_BOOT_UART_FORCE_FIFO
-static inline void arch_enable_uart_fifo(void)
-{
- u32 fifocon = uart_rd(S3C2410_UFCON);
-
- if (!(fifocon & S3C2410_UFCON_FIFOMODE)) {
- fifocon |= S3C2410_UFCON_RESETBOTH;
- uart_wr(S3C2410_UFCON, fifocon);
-
- /* wait for fifo reset to complete */
- while (1) {
- fifocon = uart_rd(S3C2410_UFCON);
- if (!(fifocon & S3C2410_UFCON_RESETBOTH))
- break;
- }
- }
-}
-#else
-#define arch_enable_uart_fifo() do { } while(0)
-#endif
-
-static void arch_decomp_setup(void)
-{
- /*
- * we may need to setup the uart(s) here if we are not running
- * on an BAST... the BAST will have left the uarts configured
- * after calling linux.
- */
-
- arch_detect_cpu();
-
- /*
- * Enable the UART FIFOs if they where not enabled and our
- * configuration says we should turn them on.
- */
-
- arch_enable_uart_fifo();
-}
-
-
-
-static void arch_detect_cpu(void)
-{
- /* we do not need to do any cpu detection here at the moment. */
+ fifo_mask = S3C2440_UFSTAT_TXMASK;
+ fifo_max = 63 << S3C2440_UFSTAT_TXSHIFT;
}
#endif /* __ASM_ARCH_UNCOMPRESS_H */
Since uart_base can be set dynamically in arch_detect_cpu(), there is no need to have a copy of all code locally, just to override UART base address. This patch removes any duplicate code in uncompress.h variant of s5p64x0 and implements proper arch_detect_cpu() function to initialize UART with SoC-specific parameters. Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> --- arch/arm/mach-s5p64x0/include/mach/uncompress.h | 155 +----------------------- 1 file changed, 5 insertions(+), 150 deletions(-)