@@ -929,7 +929,7 @@ M: Javier Martinez Canillas <javier@dowhile0.org>
L: linux-omap@vger.kernel.org
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
-F: arch/arm/mach-omap2/board-igep0020.c
+F: arch/arm/boot/dts/omap3-igep*
ARM/INCOME PXA270 SUPPORT
M: Marek Vasut <marek.vasut@gmail.com>
@@ -326,19 +326,6 @@ config MACH_CM_T3517
config MACH_CM_T3730
bool
-config MACH_IGEP0020
- bool "IGEP v2 board"
- depends on ARCH_OMAP3
- default y
- select OMAP_PACKAGE_CBB
-
-config MACH_IGEP0030
- bool "IGEP OMAP3 module"
- depends on ARCH_OMAP3
- default y
- select MACH_IGEP0020
- select OMAP_PACKAGE_CBB
-
config MACH_SBC3530
bool "OMAP3 SBC STALKER board"
depends on ARCH_OMAP3
@@ -250,7 +250,6 @@ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-peripherals.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
obj-$(CONFIG_MACH_CM_T3517) += board-cm-t3517.o
-obj-$(CONFIG_MACH_IGEP0020) += board-igep0020.o
obj-$(CONFIG_MACH_TOUCHBOOK) += board-omap3touchbook.o
obj-$(CONFIG_MACH_OMAP3517EVM) += board-am3517evm.o
deleted file mode 100644
@@ -1,683 +0,0 @@
-/*
- * Copyright (C) 2009 Integration Software and Electronic Engineering.
- *
- * Modified from mach-omap2/board-generic.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/input.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-
-#include <linux/mtd/nand.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/mtd-onenand-omap2.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "sdram-numonyx-m65kxxxxam.h"
-#include "common-board-devices.h"
-#include "board-flash.h"
-#include "control.h"
-#include "gpmc-onenand.h"
-#include "dss-common.h"
-
-#define IGEP2_SMSC911X_CS 5
-#define IGEP2_SMSC911X_GPIO 176
-#define IGEP2_GPIO_USBH_NRESET 24
-#define IGEP2_GPIO_LED0_GREEN 26
-#define IGEP2_GPIO_LED0_RED 27
-#define IGEP2_GPIO_LED1_RED 28
-
-#define IGEP2_RB_GPIO_WIFI_NPD 94
-#define IGEP2_RB_GPIO_WIFI_NRESET 95
-#define IGEP2_RB_GPIO_BT_NRESET 137
-#define IGEP2_RC_GPIO_WIFI_NPD 138
-#define IGEP2_RC_GPIO_WIFI_NRESET 139
-#define IGEP2_RC_GPIO_BT_NRESET 137
-
-#define IGEP3_GPIO_LED0_GREEN 54
-#define IGEP3_GPIO_LED0_RED 53
-#define IGEP3_GPIO_LED1_RED 16
-#define IGEP3_GPIO_USBH_NRESET 183
-
-#define IGEP_SYSBOOT_MASK 0x1f
-#define IGEP_SYSBOOT_NAND 0x0f
-#define IGEP_SYSBOOT_ONENAND 0x10
-
-/*
- * IGEP2 Hardware Revision Table
- *
- * --------------------------------------------------------------------------
- * | Id. | Hw Rev. | HW0 (28) | WIFI_NPD | WIFI_NRESET | BT_NRESET |
- * --------------------------------------------------------------------------
- * | 0 | B | high | gpio94 | gpio95 | - |
- * | 0 | B/C (B-compatible) | high | gpio94 | gpio95 | gpio137 |
- * | 1 | C | low | gpio138 | gpio139 | gpio137 |
- * --------------------------------------------------------------------------
- */
-
-#define IGEP2_BOARD_HWREV_B 0
-#define IGEP2_BOARD_HWREV_C 1
-#define IGEP3_BOARD_HWREV 2
-
-static u8 hwrev;
-
-static void __init igep2_get_revision(void)
-{
- u8 ret;
-
- if (machine_is_igep0030()) {
- hwrev = IGEP3_BOARD_HWREV;
- return;
- }
-
- omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT);
-
- if (gpio_request_one(IGEP2_GPIO_LED1_RED, GPIOF_IN, "GPIO_HW0_REV")) {
- pr_warning("IGEP2: Could not obtain gpio GPIO_HW0_REV\n");
- pr_err("IGEP2: Unknown Hardware Revision\n");
- return;
- }
-
- ret = gpio_get_value(IGEP2_GPIO_LED1_RED);
- if (ret == 0) {
- pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n");
- hwrev = IGEP2_BOARD_HWREV_C;
- } else if (ret == 1) {
- pr_info("IGEP2: Hardware Revision B/C (B compatible)\n");
- hwrev = IGEP2_BOARD_HWREV_B;
- } else {
- pr_err("IGEP2: Unknown Hardware Revision\n");
- hwrev = -1;
- }
-
- gpio_free(IGEP2_GPIO_LED1_RED);
-}
-
-#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
- defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) || \
- defined(CONFIG_MTD_NAND_OMAP2) || \
- defined(CONFIG_MTD_NAND_OMAP2_MODULE)
-
-#define ONENAND_MAP 0x20000000
-
-/* NAND04GR4E1A ( x2 Flash built-in COMBO POP MEMORY )
- * Since the device is equipped with two DataRAMs, and two-plane NAND
- * Flash memory array, these two component enables simultaneous program
- * of 4KiB. Plane1 has only even blocks such as block0, block2, block4
- * while Plane2 has only odd blocks such as block1, block3, block5.
- * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
- */
-
-static struct mtd_partition igep_flash_partitions[] = {
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 2 * (64*(2*2048))
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND,
- .size = 6 * (64*(2*2048)),
- },
- {
- .name = "Environment",
- .offset = MTDPART_OFS_APPEND,
- .size = 2 * (64*(2*2048)),
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 12 * (64*(2*2048)),
- },
- {
- .name = "File System",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static inline u32 igep_get_sysboot_value(void)
-{
- return omap_ctrl_readl(OMAP343X_CONTROL_STATUS) & IGEP_SYSBOOT_MASK;
-}
-
-static void __init igep_flash_init(void)
-{
- u32 mux;
- mux = igep_get_sysboot_value();
-
- if (mux == IGEP_SYSBOOT_NAND) {
- pr_info("IGEP: initializing NAND memory device\n");
- board_nand_init(igep_flash_partitions,
- ARRAY_SIZE(igep_flash_partitions),
- 0, NAND_BUSWIDTH_16, nand_default_timings);
- } else if (mux == IGEP_SYSBOOT_ONENAND) {
- pr_info("IGEP: initializing OneNAND memory device\n");
- board_onenand_init(igep_flash_partitions,
- ARRAY_SIZE(igep_flash_partitions), 0);
- } else {
- pr_err("IGEP: Flash: unsupported sysboot sequence found\n");
- }
-}
-
-#else
-static void __init igep_flash_init(void) {}
-#endif
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-
-#include <linux/smsc911x.h>
-#include "gpmc-smsc911x.h"
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
- .cs = IGEP2_SMSC911X_CS,
- .gpio_irq = IGEP2_SMSC911X_GPIO,
- .gpio_reset = -EINVAL,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static inline void __init igep2_init_smsc911x(void)
-{
- gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init igep2_init_smsc911x(void) { }
-#endif
-
-static struct regulator_consumer_supply igep_vmmc1_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data igep_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(igep_vmmc1_supply),
- .consumer_supplies = igep_vmmc1_supply,
-};
-
-static struct regulator_consumer_supply igep_vio_supply[] = {
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1"),
-};
-
-static struct regulator_init_data igep_vio = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = 1,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(igep_vio_supply),
- .consumer_supplies = igep_vio_supply,
-};
-
-static struct regulator_consumer_supply igep_vmmc2_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-static struct regulator_init_data igep_vmmc2 = {
- .constraints = {
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .always_on = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(igep_vmmc2_supply),
- .consumer_supplies = igep_vmmc2_supply,
-};
-
-static struct fixed_voltage_config igep_vwlan = {
- .supply_name = "vwlan",
- .microvolts = 3300000,
- .gpio = -EINVAL,
- .enabled_at_boot = 1,
- .init_data = &igep_vmmc2,
-};
-
-static struct platform_device igep_vwlan_device = {
- .name = "reg-fixed-voltage",
- .id = 0,
- .dev = {
- .platform_data = &igep_vwlan,
- },
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- .deferred = true,
- },
-#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
- {
- .mmc = 2,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
-#endif
- {} /* Terminator */
-};
-
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-#include <linux/leds.h>
-
-static struct gpio_led igep_gpio_leds[] = {
- [0] = {
- .name = "omap3:red:user0",
- .default_state = 0,
- },
- [1] = {
- .name = "omap3:green:boot",
- .default_state = 1,
- },
- [2] = {
- .name = "omap3:red:user1",
- .default_state = 0,
- },
- [3] = {
- .name = "omap3:green:user1",
- .default_state = 0,
- .gpio = -EINVAL, /* gets replaced */
- .active_low = 1,
- },
-};
-
-static struct gpio_led_platform_data igep_led_pdata = {
- .leds = igep_gpio_leds,
- .num_leds = ARRAY_SIZE(igep_gpio_leds),
-};
-
-static struct platform_device igep_led_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &igep_led_pdata,
- },
-};
-
-static void __init igep_leds_init(void)
-{
- if (machine_is_igep0020()) {
- igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
- } else {
- igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
- }
-
- platform_device_register(&igep_led_device);
-}
-
-#else
-static struct gpio igep_gpio_leds[] __initdata = {
- { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" },
- { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" },
- { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" },
-};
-
-static inline void igep_leds_init(void)
-{
- int i;
-
- if (machine_is_igep0020()) {
- igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
- } else {
- igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
- }
-
- if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) {
- pr_warning("IGEP v2: Could not obtain leds gpios\n");
- return;
- }
-
- for (i = 0; i < ARRAY_SIZE(igep_gpio_leds); i++)
- gpio_export(igep_gpio_leds[i].gpio, 0);
-}
-#endif
-
-static struct gpio igep2_twl_gpios[] = {
- { -EINVAL, GPIOF_IN, "GPIO_EHCI_NOC" },
- { -EINVAL, GPIOF_OUT_INIT_LOW, "GPIO_USBH_CPEN" },
-};
-
-static int igep_twl_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- int ret;
-
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap_hsmmc_late_init(mmc);
-
- /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
-#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
- ret = gpio_request_one(gpio + TWL4030_GPIO_MAX + 1, GPIOF_OUT_INIT_HIGH,
- "gpio-led:green:d1");
- if (ret == 0)
- gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
- else
- pr_warning("IGEP: Could not obtain gpio GPIO_LED1_GREEN\n");
-#else
- igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
-#endif
-
- if (machine_is_igep0030())
- return 0;
-
- /*
- * REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- igep2_twl_gpios[0].gpio = gpio + 1;
-
- /* TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN (out, active low) */
- igep2_twl_gpios[1].gpio = gpio + TWL4030_GPIO_MAX;
-
- ret = gpio_request_array(igep2_twl_gpios, ARRAY_SIZE(igep2_twl_gpios));
- if (ret < 0)
- pr_err("IGEP2: Could not obtain gpio for USBH_CPEN");
-
- return 0;
-};
-
-static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = {
- .use_leds = true,
- .setup = igep_twl_gpio_setup,
-};
-
-static int igep2_keymap[] = {
- KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_RIGHT),
- KEY(0, 2, KEY_A),
- KEY(0, 3, KEY_B),
- KEY(1, 0, KEY_DOWN),
- KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_E),
- KEY(1, 3, KEY_F),
- KEY(2, 0, KEY_ENTER),
- KEY(2, 1, KEY_I),
- KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_K),
- KEY(3, 0, KEY_M),
- KEY(3, 1, KEY_N),
- KEY(3, 2, KEY_O),
- KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data igep2_keymap_data = {
- .keymap = igep2_keymap,
- .keymap_size = ARRAY_SIZE(igep2_keymap),
-};
-
-static struct twl4030_keypad_data igep2_keypad_pdata = {
- .keymap_data = &igep2_keymap_data,
- .rows = 4,
- .cols = 4,
- .rep = 1,
-};
-
-static struct twl4030_platform_data igep_twldata = {
- /* platform_data for children goes here */
- .gpio = &igep_twl4030_gpio_pdata,
- .vmmc1 = &igep_vmmc1,
- .vio = &igep_vio,
-};
-
-static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = {
- {
- I2C_BOARD_INFO("eeprom", 0x50),
- },
-};
-
-static void __init igep_i2c_init(void)
-{
- int ret;
-
- omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_USB,
- TWL_COMMON_REGULATOR_VPLL2);
- igep_twldata.vpll2->constraints.apply_uV = true;
- igep_twldata.vpll2->constraints.name = "VDVI";
-
- if (machine_is_igep0020()) {
- /*
- * Bus 3 is attached to the DVI port where devices like the
- * pico DLP projector don't work reliably with 400kHz
- */
- ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
- ARRAY_SIZE(igep2_i2c3_boardinfo));
- if (ret)
- pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
-
- igep_twldata.keypad = &igep2_keypad_pdata;
- /* Get common pmic data */
- omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_AUDIO, 0);
- }
-
- omap3_pmic_init("twl4030", &igep_twldata);
-}
-
-static struct usbhs_phy_data igep2_phy_data[] __initdata = {
- {
- .port = 1,
- .reset_gpio = IGEP2_GPIO_USBH_NRESET,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_phy_data igep3_phy_data[] __initdata = {
- {
- .port = 2,
- .reset_gpio = IGEP3_GPIO_USBH_NRESET,
- .vcc_gpio = -EINVAL,
- },
-};
-
-static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = {
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- /* Display Sub System */
- OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
- /* TFP410 PanelBus DVI Transmitte (GPIO_170) */
- OMAP3_MUX(HDQ_SIO, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- /* SMSC9221 LAN Controller ETH IRQ (GPIO_176) */
- OMAP3_MUX(MCSPI1_CS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
-static struct gpio igep_wlan_bt_gpios[] __initdata = {
- { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NPD" },
- { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NRESET" },
- { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_BT_NRESET" },
-};
-
-static void __init igep_wlan_bt_init(void)
-{
- int err;
-
- /* GPIO's for WLAN-BT combo depends on hardware revision */
- if (hwrev == IGEP2_BOARD_HWREV_B) {
- igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD;
- igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET;
- igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET;
- } else if (hwrev == IGEP2_BOARD_HWREV_C || machine_is_igep0030()) {
- igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD;
- igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET;
- igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET;
- } else
- return;
-
- /* Make sure that the GPIO pins are muxed correctly */
- omap_mux_init_gpio(igep_wlan_bt_gpios[0].gpio, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(igep_wlan_bt_gpios[1].gpio, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(igep_wlan_bt_gpios[2].gpio, OMAP_PIN_OUTPUT);
-
- err = gpio_request_array(igep_wlan_bt_gpios,
- ARRAY_SIZE(igep_wlan_bt_gpios));
- if (err) {
- pr_warning("IGEP2: Could not obtain WIFI/BT gpios\n");
- return;
- }
-
- gpio_export(igep_wlan_bt_gpios[0].gpio, 0);
- gpio_export(igep_wlan_bt_gpios[1].gpio, 0);
- gpio_export(igep_wlan_bt_gpios[2].gpio, 0);
-
- gpio_set_value(igep_wlan_bt_gpios[1].gpio, 0);
- udelay(10);
- gpio_set_value(igep_wlan_bt_gpios[1].gpio, 1);
-
-}
-#else
-static inline void __init igep_wlan_bt_init(void) { }
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init igep_init(void)
-{
- regulator_register_fixed(1, dummy_supplies, ARRAY_SIZE(dummy_supplies));
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-
- /* Get IGEP2 hardware revision */
- igep2_get_revision();
-
- omap_hsmmc_init(mmc);
-
- /* Register I2C busses and drivers */
- igep_i2c_init();
- platform_device_register(&igep_vwlan_device);
- omap3_igep2_display_init_of();
- omap_serial_init();
- omap_sdrc_init(m65kxxxxam_sdrc_params,
- m65kxxxxam_sdrc_params);
- usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
- usb_musb_init(NULL);
-
- igep_flash_init();
- igep_leds_init();
- omap_twl4030_audio_init("igep2", NULL);
-
- /*
- * WLAN-BT combo module from MuRata which has a Marvell WLAN
- * (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
- */
- igep_wlan_bt_init();
-
- if (machine_is_igep0020()) {
- igep2_init_smsc911x();
- usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data));
- usbhs_init(&igep2_usbhs_bdata);
- } else {
- usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data));
- usbhs_init(&igep3_usbhs_bdata);
- }
-}
-
-MACHINE_START(IGEP0020, "IGEP v2 board")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = igep_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(IGEP0030, "IGEP OMAP3 module")
- .atag_offset = 0x100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = omap35xx_init_early,
- .init_irq = omap3_init_irq,
- .handle_irq = omap3_intc_handle_irq,
- .init_machine = igep_init,
- .init_late = omap35xx_init_late,
- .init_time = omap3_sync32k_timer_init,
- .restart = omap3xxx_restart,
-MACHINE_END
Device Tree support for IGEP boards in mainline is almost finished. The only remaining bits are support for the Marvell SD8686 wifi + BT and TFP410 DVI chips. Adding support for these should be straightforward so let's not block OMAP3 moving to Device Tree only boot and remove the board file for IGEP boards. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> --- Changes since v1: - Also remove the Kconfig and Makefile entries for IGEP boards. MAINTAINERS | 2 +- arch/arm/mach-omap2/Kconfig | 13 - arch/arm/mach-omap2/Makefile | 1 - arch/arm/mach-omap2/board-igep0020.c | 683 ----------------------------------- 4 files changed, 1 insertion(+), 698 deletions(-) delete mode 100644 arch/arm/mach-omap2/board-igep0020.c