@@ -21,7 +21,6 @@
#include <linux/mutex.h>
#include <linux/mfd/pm8xxx/core.h>
-#include <linux/mfd/pm8xxx/gpio.h>
#include <linux/input/pmic8xxx-keypad.h>
#define PM8XXX_MAX_ROWS 18
@@ -447,27 +446,6 @@ static int pmic8xxx_kpd_init(struct pmic8xxx_kp *kp)
}
-static int pmic8xxx_kp_config_gpio(int gpio_start, int num_gpios,
- struct pmic8xxx_kp *kp, struct pm_gpio *gpio_config)
-{
- int rc, i;
-
- if (gpio_start < 0 || num_gpios < 0)
- return -EINVAL;
-
- for (i = 0; i < num_gpios; i++) {
- rc = pm8xxx_gpio_config(gpio_start + i, gpio_config);
- if (rc) {
- dev_err(kp->dev, "%s: FAIL pm8xxx_gpio_config():"
- "for PM GPIO [%d] rc=%d.\n",
- __func__, gpio_start + i, rc);
- return rc;
- }
- }
-
- return 0;
-}
-
static int pmic8xxx_kp_enable(struct pmic8xxx_kp *kp)
{
int rc;
@@ -527,27 +505,6 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
int rc;
u8 ctrl_val;
- struct pm_gpio kypd_drv = {
- .direction = PM_GPIO_DIR_OUT,
- .output_buffer = PM_GPIO_OUT_BUF_OPEN_DRAIN,
- .output_value = 0,
- .pull = PM_GPIO_PULL_NO,
- .vin_sel = PM_GPIO_VIN_S3,
- .out_strength = PM_GPIO_STRENGTH_LOW,
- .function = PM_GPIO_FUNC_1,
- .inv_int_pol = 1,
- };
-
- struct pm_gpio kypd_sns = {
- .direction = PM_GPIO_DIR_IN,
- .pull = PM_GPIO_PULL_UP_31P5,
- .vin_sel = PM_GPIO_VIN_S3,
- .out_strength = PM_GPIO_STRENGTH_NO,
- .function = PM_GPIO_FUNC_NORMAL,
- .inv_int_pol = 1,
- };
-
-
if (!pdata || !pdata->num_cols || !pdata->num_rows ||
pdata->num_cols > PM8XXX_MAX_COLS ||
pdata->num_rows > PM8XXX_MAX_ROWS ||
@@ -653,20 +610,6 @@ static int pmic8xxx_kp_probe(struct platform_device *pdev)
goto err_get_irq;
}
- rc = pmic8xxx_kp_config_gpio(pdata->cols_gpio_start,
- pdata->num_cols, kp, &kypd_sns);
- if (rc < 0) {
- dev_err(&pdev->dev, "unable to configure keypad sense lines\n");
- goto err_gpio_config;
- }
-
- rc = pmic8xxx_kp_config_gpio(pdata->rows_gpio_start,
- pdata->num_rows, kp, &kypd_drv);
- if (rc < 0) {
- dev_err(&pdev->dev, "unable to configure keypad drive lines\n");
- goto err_gpio_config;
- }
-
rc = request_any_context_irq(kp->key_sense_irq, pmic8xxx_kp_irq,
IRQF_TRIGGER_RISING, "pmic-keypad", kp);
if (rc < 0) {
@@ -703,7 +646,6 @@ err_pmic_reg_read:
free_irq(kp->key_stuck_irq, kp);
err_req_stuck_irq:
free_irq(kp->key_sense_irq, kp);
-err_gpio_config:
err_get_irq:
input_free_device(kp->input);
err_alloc_device:
The gpio configuration in this driver doesn't work because the gpio.h include doesn't exist. Remove the configuration as it isn't strictly necessary, allowing us to actually compile this driver. If it's needed in the future, it should be done via a pinctrl driver. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> --- drivers/input/keyboard/pmic8xxx-keypad.c | 58 -------------------------------- 1 file changed, 58 deletions(-)