new file mode 100644
@@ -0,0 +1,27 @@
+* SiRF SoC USP module
+
+Required properties:
+- compatible: "sirf,prima2-usp-pcm"
+- reg: Base address and size entries:
+- dmas: List of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: Identifier string for each DMA request line in the dmas property.
+ These strings correspond 1:1 with the ordered pairs in dmas.
+
+ One of the DMA channels will be responsible for transmission (should be
+ named "tx") and one for reception (should be named "rx").
+
+- clocks: USP controller clock source
+- pinctrl-names: Must contain a "default" entry.
+- pinctrl-NNN: One property must exist for each entry in pinctrl-names.
+
+Example:
+
+usp1: usp@b0090000 {
+ compatible = "sirf,prima2-usp-pcm";
+ reg = <0xb0090000 0x10000>;
+ clocks = <&clks 29>;
+ dmas = <&dmac0 14>, <&dmac0 15>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usp0_only_utfs_pins_a>;
+};
@@ -13,6 +13,10 @@ config SND_SOC_SIRF_AUDIO_PORT
select REGMAP_MMIO
tristate
+config SND_SOC_SIRF_I2S
+ select REGMAP_MMIO
+ tristate
+
config SND_SOC_SIRF_HDMI
tristate "SoC Audio support for SiRF HDMI"
depends on SND_SOC_SIRF
@@ -22,3 +26,7 @@ config SND_SOC_SIRF_HDMI
config SND_SOC_SIRF_I2S
select REGMAP_MMIO
tristate
+
+config SND_SOC_SIRF_USP
+ select REGMAP_MMIO
+ tristate
@@ -2,8 +2,10 @@ snd-soc-sirf-audio-objs := sirf-audio.o
snd-soc-sirf-audio-port-objs := sirf-audio-port.o
snd-soc-sirf-hdmi-objs := sirf-hdmi.o
snd-soc-sirf-i2s-objs := sirf-i2s.o
+snd-soc-sirf-usp-objs := sirf-usp.o
obj-$(CONFIG_SND_SOC_SIRF_AUDIO) += snd-soc-sirf-audio.o
obj-$(CONFIG_SND_SOC_SIRF_AUDIO_PORT) += snd-soc-sirf-audio-port.o
obj-$(CONFIG_SND_SOC_SIRF_HDMI) += snd-soc-sirf-hdmi.o
obj-$(CONFIG_SND_SOC_SIRF_I2S) += snd-soc-sirf-i2s.o
+obj-$(CONFIG_SND_SOC_SIRF_USP) += snd-soc-sirf-usp.o
new file mode 100644
@@ -0,0 +1,448 @@
+/*
+ * SiRF USP audio transfer interface like I2S
+ *
+ * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/pm_runtime.h>
+#include <sound/soc.h>
+#include <sound/dmaengine_pcm.h>
+
+#include "sirf-usp.h"
+
+#define FIFO_RESET 0
+#define FIFO_START 1
+#define FIFO_STOP 2
+
+#define AUDIO_WORD_SIZE 16
+
+struct sirf_usp {
+ struct regmap *regmap;
+ struct clk *clk;
+ u32 mode1_reg;
+ u32 mode2_reg;
+ int master;
+ struct snd_dmaengine_dai_dma_data playback_dma_data;
+ struct snd_dmaengine_dai_dma_data capture_dma_data;
+};
+
+static void sirf_usp_tx_enable(struct sirf_usp *usp)
+{
+ regmap_update_bits(usp->regmap, USP_TX_FIFO_OP,
+ USP_TX_FIFO_RESET, USP_TX_FIFO_RESET);
+ regmap_write(usp->regmap, USP_TX_FIFO_OP, 0);
+
+ regmap_update_bits(usp->regmap, USP_TX_FIFO_OP,
+ USP_TX_FIFO_START, USP_TX_FIFO_START);
+
+ regmap_update_bits(usp->regmap, USP_TX_RX_ENABLE,
+ USP_TX_ENA, USP_TX_ENA);
+}
+
+static void sirf_usp_tx_disable(struct sirf_usp *usp)
+{
+ regmap_update_bits(usp->regmap, USP_TX_RX_ENABLE,
+ USP_TX_ENA, ~USP_TX_ENA);
+ /* FIFO stop */
+ regmap_write(usp->regmap, USP_TX_FIFO_OP, 0);
+}
+
+static void sirf_usp_rx_enable(struct sirf_usp *usp)
+{
+ regmap_update_bits(usp->regmap, USP_RX_FIFO_OP,
+ USP_RX_FIFO_RESET, USP_RX_FIFO_RESET);
+ regmap_write(usp->regmap, USP_RX_FIFO_OP, 0);
+
+ regmap_update_bits(usp->regmap, USP_RX_FIFO_OP,
+ USP_RX_FIFO_START, USP_RX_FIFO_START);
+
+ regmap_update_bits(usp->regmap, USP_TX_RX_ENABLE,
+ USP_RX_ENA, USP_RX_ENA);
+}
+
+static void sirf_usp_rx_disable(struct sirf_usp *usp)
+{
+ regmap_update_bits(usp->regmap, USP_TX_RX_ENABLE,
+ USP_RX_ENA, ~USP_RX_ENA);
+ /* FIFO stop */
+ regmap_write(usp->regmap, USP_RX_FIFO_OP, 0);
+}
+
+static int sirf_usp_pcm_dai_probe(struct snd_soc_dai *dai)
+{
+ struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+ snd_soc_dai_init_dma_data(dai, &usp->playback_dma_data,
+ &usp->capture_dma_data);
+ return 0;
+}
+
+static int sirf_usp_pcm_set_dai_fmt(struct snd_soc_dai *dai,
+ unsigned int fmt)
+{
+ struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+
+ /* set master/slave audio interface */
+ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+ case SND_SOC_DAIFMT_CBS_CFS:
+ usp->master = 1;
+ break;
+ case SND_SOC_DAIFMT_CBM_CFM:
+ usp->master = 0;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int sirf_usp_pcm_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params, struct snd_soc_dai *dai)
+{
+ struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+ u32 mode1;
+ u32 mode2;
+ u32 rate = params_rate(params);
+ u32 clk_rate, clk_div, clk_div_hi, clk_div_lo;
+
+ regmap_read(usp->regmap, USP_MODE1, &mode1);
+ regmap_read(usp->regmap, USP_MODE2, &mode2);
+ if (usp->master) {
+ mode1 &= ~USP_CLOCK_MODE_SLAVE;
+ mode2 &= ~USP_TFS_CLK_SLAVE_MODE;
+ mode2 &= ~USP_RFS_CLK_SLAVE_MODE;
+ } else {
+ mode1 |= USP_CLOCK_MODE_SLAVE;
+ mode2 |= USP_TFS_CLK_SLAVE_MODE;
+ mode2 |= USP_RFS_CLK_SLAVE_MODE;
+ }
+ regmap_write(usp->regmap, USP_MODE1, mode1);
+ regmap_write(usp->regmap, USP_MODE2, mode2);
+
+ clk_rate = clk_get_rate(usp->clk);
+ if (clk_rate < rate * 2) {
+ dev_err(dai->dev, "Can't get rate(%d) by need.\n", rate);
+ return -EINVAL;
+ }
+
+ clk_div = (clk_rate / (2 * rate)) - 1;
+ clk_div_hi = (clk_div & 0xC00) >> 10;
+ clk_div_lo = (clk_div & 0x3FF);
+
+ regmap_update_bits(usp->regmap, USP_MODE2, USP_CLK_DIVISOR_MASK,
+ clk_div_lo << USP_CLK_DIVISOR_OFFSET);
+
+ regmap_update_bits(usp->regmap, USP_TX_FRAME_CTRL,
+ USP_TXC_CLK_DIVISOR_MASK,
+ clk_div_hi << USP_TXC_CLK_DIVISOR_OFFSET);
+
+ return 0;
+}
+
+static int sirf_usp_pcm_trigger(struct snd_pcm_substream *substream, int cmd,
+ struct snd_soc_dai *dai)
+{
+ int playback = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
+ struct sirf_usp *usp = snd_soc_dai_get_drvdata(dai);
+
+ switch (cmd) {
+ case SNDRV_PCM_TRIGGER_START:
+ case SNDRV_PCM_TRIGGER_RESUME:
+ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+ if (playback)
+ sirf_usp_tx_enable(usp);
+ else
+ sirf_usp_rx_enable(usp);
+ break;
+ case SNDRV_PCM_TRIGGER_STOP:
+ case SNDRV_PCM_TRIGGER_SUSPEND:
+ case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+ if (playback)
+ sirf_usp_tx_disable(usp);
+ else
+ sirf_usp_rx_disable(usp);
+ break;
+ }
+
+ return 0;
+}
+
+static const struct snd_soc_dai_ops sirf_usp_pcm_dai_ops = {
+ .trigger = sirf_usp_pcm_trigger,
+ .set_fmt = sirf_usp_pcm_set_dai_fmt,
+ .hw_params = sirf_usp_pcm_hw_params,
+};
+
+static struct snd_soc_dai_driver sirf_usp_pcm_dai = {
+ .probe = sirf_usp_pcm_dai_probe,
+ .name = "sirf-usp-pcm",
+ .id = 0,
+ .playback = {
+ .stream_name = "SiRF USP PCM Playback",
+ .channels_min = 1,
+ .channels_max = 1,
+ .rates = SNDRV_PCM_RATE_48000
+ | SNDRV_PCM_RATE_44100
+ | SNDRV_PCM_RATE_32000
+ | SNDRV_PCM_RATE_22050
+ | SNDRV_PCM_RATE_16000
+ | SNDRV_PCM_RATE_11025
+ | SNDRV_PCM_RATE_8000,
+ .formats = SNDRV_PCM_FMTBIT_S16_LE,
+ },
+ .capture = {
+ .stream_name = "SiRF USP PCM Capture",
+ .channels_min = 1,
+ .channels_max = 1,
+ .rates = SNDRV_PCM_RATE_48000
+ | SNDRV_PCM_RATE_44100
+ | SNDRV_PCM_RATE_32000
+ | SNDRV_PCM_RATE_22050
+ | SNDRV_PCM_RATE_16000
+ | SNDRV_PCM_RATE_11025
+ | SNDRV_PCM_RATE_8000,
+ .formats = SNDRV_PCM_FMTBIT_S16_LE,
+ },
+ .ops = &sirf_usp_pcm_dai_ops,
+};
+
+static void sirf_usp_controller_init(struct sirf_usp *usp)
+{
+ u32 val;
+
+ /* Configure RISC mode */
+ regmap_update_bits(usp->regmap, USP_RISC_DSP_MODE,
+ USP_RISC_DSP_SEL, ~USP_RISC_DSP_SEL);
+
+ /* Clear all interrupts status */
+ regmap_read(usp->regmap, USP_INT_STATUS, &val);
+ regmap_write(usp->regmap, USP_INT_STATUS, val);
+
+ /* Configure DMA IO Length register */
+ regmap_write(usp->regmap, USP_TX_DMA_IO_LEN, 0);
+ regmap_write(usp->regmap, USP_RX_DMA_IO_LEN, 0);
+
+ /* Configure RX Frame Control */
+ val = (AUDIO_WORD_SIZE * 2 - 1) << USP_RXC_DATA_LEN_OFFSET;
+ val |= (AUDIO_WORD_SIZE * 2 - 1) << USP_RXC_FRAME_LEN_OFFSET;
+ val |= (AUDIO_WORD_SIZE * 2 - 1) << USP_RXC_SHIFTER_LEN_OFFSET;
+ val |= USP_SINGLE_SYNC_MODE;
+ regmap_write(usp->regmap, USP_RX_FRAME_CTRL, val);
+
+ /* Configure TX Frame Control */
+ val = (AUDIO_WORD_SIZE * 2 - 1) << USP_TXC_DATA_LEN_OFFSET;
+ val |= 0 << USP_TXC_SYNC_LEN_OFFSET;
+ val |= (AUDIO_WORD_SIZE * 2 - 1) << USP_TXC_FRAME_LEN_OFFSET;
+ val |= (AUDIO_WORD_SIZE * 2 - 1) << USP_TXC_SHIFTER_LEN_OFFSET;
+ val |= USP_TXC_SLAVE_CLK_SAMPLE;
+ regmap_write(usp->regmap, USP_TX_FRAME_CTRL, val);
+
+ /* Configure Mode2 register */
+ val = (1 << USP_RXD_DELAY_LEN_OFFSET) | (0 << USP_TXD_DELAY_LEN_OFFSET);
+ val &= ~USP_ENA_CTRL_MODE;
+ val &= ~USP_FRAME_CTRL_MODE;
+ val &= ~USP_TFS_SOURCE_MODE;
+ regmap_write(usp->regmap, USP_MODE2, val);
+
+ /* Configure Mode1 register */
+ val = USP_SYNC_MODE;
+ val |= USP_ENDIAN_CTRL_LSBF;
+ val |= USP_EN;
+ val |= USP_RXD_ACT_EDGE_FALLING;
+ val &= ~USP_TXD_ACT_EDGE_FALLING;
+ val |= USP_RFS_ACT_LEVEL_LOGIC1;
+ val |= USP_TFS_ACT_LEVEL_LOGIC1;
+ val |= USP_SCLK_IDLE_MODE_TOGGLE;
+ val |= USP_SCLK_IDLE_LEVEL_LOGIC1;
+ val &= ~USP_SCLK_PIN_MODE_IO;
+ val &= ~USP_RFS_PIN_MODE_IO;
+ val &= ~USP_TFS_PIN_MODE_IO;
+ val &= ~USP_RXD_PIN_MODE_IO;
+ val &= ~USP_TXD_PIN_MODE_IO;
+ val |= USP_TX_UFLOW_REPEAT_ZERO;
+ regmap_write(usp->regmap, USP_MODE1, val);
+
+ /* Configure RX DMA IO Control register */
+ regmap_write(usp->regmap, USP_RX_DMA_IO_CTRL, 0);
+
+ /* Congiure RX FIFO Control register */
+ regmap_write(usp->regmap, USP_RX_FIFO_CTRL,
+ (USP_RX_FIFO_THRESHOLD << USP_RX_FIFO_THD_OFFSET) |
+ (USP_TX_RX_FIFO_WIDTH_DWORD << USP_RX_FIFO_WIDTH_OFFSET));
+
+ /* Congiure RX FIFO Level Check register */
+ regmap_write(usp->regmap, USP_RX_FIFO_LEVEL_CHK,
+ RX_FIFO_SC(0x04) | RX_FIFO_LC(0x0E) | RX_FIFO_HC(0x1B));
+
+ /* Configure TX DMA IO Control register*/
+ regmap_write(usp->regmap, USP_TX_DMA_IO_CTRL, 0);
+
+ /* Configure TX FIFO Control register */
+ regmap_write(usp->regmap, USP_TX_FIFO_CTRL,
+ (USP_TX_FIFO_THRESHOLD << USP_TX_FIFO_THD_OFFSET) |
+ (USP_TX_RX_FIFO_WIDTH_DWORD << USP_TX_FIFO_WIDTH_OFFSET));
+
+ /* Congiure TX FIFO Level Check register */
+ regmap_write(usp->regmap, USP_TX_FIFO_LEVEL_CHK,
+ TX_FIFO_SC(0x1B) | TX_FIFO_LC(0x0E) | TX_FIFO_HC(0x04));
+
+ /* Configure RX FIFO */
+ regmap_update_bits(usp->regmap, USP_RX_FIFO_OP,
+ USP_RX_FIFO_RESET, USP_RX_FIFO_RESET);
+ regmap_write(usp->regmap, USP_RX_FIFO_OP, 0);
+
+ /* Configure TX FIFO */
+ regmap_update_bits(usp->regmap, USP_TX_FIFO_OP,
+ USP_TX_FIFO_RESET, USP_TX_FIFO_RESET);
+ regmap_write(usp->regmap, USP_TX_FIFO_OP, 0);
+}
+
+static void sirf_usp_controller_uninit(struct sirf_usp *usp)
+{
+ /* Disable RX/TX */
+ regmap_write(usp->regmap, USP_INT_ENABLE, 0);
+ regmap_write(usp->regmap, USP_TX_RX_ENABLE, 0);
+}
+
+#ifdef CONFIG_PM_RUNTIME
+static int sirf_usp_pcm_runtime_suspend(struct device *dev)
+{
+ struct sirf_usp *usp = dev_get_drvdata(dev);
+ sirf_usp_controller_uninit(usp);
+ clk_disable_unprepare(usp->clk);
+ return 0;
+}
+
+static int sirf_usp_pcm_runtime_resume(struct device *dev)
+{
+ struct sirf_usp *usp = dev_get_drvdata(dev);
+ int ret;
+ ret = clk_prepare_enable(usp->clk);
+ if (ret)
+ return ret;
+ sirf_usp_controller_init(usp);
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_PM_SLEEP
+static int sirf_usp_pcm_suspend(struct device *dev)
+{
+ struct sirf_usp *usp = dev_get_drvdata(dev);
+
+ if (!pm_runtime_status_suspended(dev)) {
+ regmap_read(usp->regmap, USP_MODE1, &usp->mode1_reg);
+ regmap_read(usp->regmap, USP_MODE2, &usp->mode2_reg);
+ sirf_usp_pcm_runtime_suspend(dev);
+ }
+ return 0;
+}
+
+static int sirf_usp_pcm_resume(struct device *dev)
+{
+ struct sirf_usp *usp = dev_get_drvdata(dev);
+ int ret;
+
+ if (!pm_runtime_status_suspended(dev)) {
+ ret = sirf_usp_pcm_runtime_resume(dev);
+ if (ret)
+ return ret;
+ regmap_write(usp->regmap, USP_MODE1, usp->mode1_reg);
+ regmap_write(usp->regmap, USP_MODE2, usp->mode2_reg);
+ }
+ return 0;
+}
+#endif
+
+static const struct snd_soc_component_driver sirf_usp_component = {
+ .name = "sirf-usp",
+};
+
+static const struct regmap_config sirf_usp_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = USP_RX_FIFO_DATA,
+ .cache_type = REGCACHE_NONE,
+};
+
+static int sirf_usp_pcm_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct sirf_usp *usp;
+ void __iomem *base;
+ struct resource *mem_res;
+
+ usp = devm_kzalloc(&pdev->dev, sizeof(struct sirf_usp),
+ GFP_KERNEL);
+ if (!usp)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, usp);
+
+
+ mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap(&pdev->dev, mem_res->start,
+ resource_size(mem_res));
+ if (base == NULL)
+ return -ENOMEM;
+ usp->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+ &sirf_usp_regmap_config);
+ if (IS_ERR(usp->regmap))
+ return PTR_ERR(usp->regmap);
+
+ usp->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(usp->clk)) {
+ dev_err(&pdev->dev, "Get clock failed.\n");
+ return PTR_ERR(usp->clk);
+ }
+
+ pm_runtime_enable(&pdev->dev);
+
+ ret = devm_snd_soc_register_component(&pdev->dev, &sirf_usp_component,
+ &sirf_usp_pcm_dai, 1);
+ if (ret) {
+ dev_err(&pdev->dev, "Register Audio SoC dai failed.\n");
+ return ret;
+ }
+ return devm_snd_dmaengine_pcm_register(&pdev->dev, NULL, 0);
+}
+
+static int sirf_usp_pcm_remove(struct platform_device *pdev)
+{
+ pm_runtime_disable(&pdev->dev);
+ return 0;
+}
+
+static const struct of_device_id sirf_usp_pcm_of_match[] = {
+ { .compatible = "sirf,prima2-usp-pcm", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sirf_usp_pcm_of_match);
+
+static const struct dev_pm_ops sirf_usp_pcm_pm_ops = {
+ SET_RUNTIME_PM_OPS(sirf_usp_pcm_runtime_suspend, sirf_usp_pcm_runtime_resume, NULL)
+ SET_SYSTEM_SLEEP_PM_OPS(sirf_usp_pcm_suspend, sirf_usp_pcm_resume)
+};
+
+static struct platform_driver sirf_usp_pcm_driver = {
+ .driver = {
+ .name = "sirf-usp-pcm",
+ .owner = THIS_MODULE,
+ .of_match_table = sirf_usp_pcm_of_match,
+ .pm = &sirf_usp_pcm_pm_ops,
+ },
+ .probe = sirf_usp_pcm_probe,
+ .remove = sirf_usp_pcm_remove,
+};
+
+module_platform_driver(sirf_usp_pcm_driver);
+
+MODULE_DESCRIPTION("SiRF SoC USP PCM bus driver");
+MODULE_AUTHOR("RongJun Ying <Rongjun.Ying@csr.com>");
+MODULE_LICENSE("GPL v2");
new file mode 100644
@@ -0,0 +1,282 @@
+/*
+ * arch/arm/mach-prima2/include/mach/sirfsoc_usp.h
+ *
+ * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#ifndef _SIRF_USP_H
+#define _SIRF_USP_H
+
+/* USP Registers */
+#define USP_MODE1 0x00
+#define USP_MODE2 0x04
+#define USP_TX_FRAME_CTRL 0x08
+#define USP_RX_FRAME_CTRL 0x0C
+#define USP_TX_RX_ENABLE 0x10
+#define USP_INT_ENABLE 0x14
+#define USP_INT_STATUS 0x18
+#define USP_PIN_IO_DATA 0x1C
+#define USP_RISC_DSP_MODE 0x20
+#define USP_AYSNC_PARAM_REG 0x24
+#define USP_IRDA_X_MODE_DIV 0x28
+#define USP_SM_CFG 0x2C
+#define USP_TX_DMA_IO_CTRL 0x100
+#define USP_TX_DMA_IO_LEN 0x104
+#define USP_TX_FIFO_CTRL 0x108
+#define USP_TX_FIFO_LEVEL_CHK 0x10C
+#define USP_TX_FIFO_OP 0x110
+#define USP_TX_FIFO_STATUS 0x114
+#define USP_TX_FIFO_DATA 0x118
+#define USP_RX_DMA_IO_CTRL 0x120
+#define USP_RX_DMA_IO_LEN 0x124
+#define USP_RX_FIFO_CTRL 0x128
+#define USP_RX_FIFO_LEVEL_CHK 0x12C
+#define USP_RX_FIFO_OP 0x130
+#define USP_RX_FIFO_STATUS 0x134
+#define USP_RX_FIFO_DATA 0x138
+
+/* USP MODE register-1 */
+#define USP_SYNC_MODE 0x00000001
+#define USP_CLOCK_MODE_SLAVE 0x00000002
+#define USP_LOOP_BACK_EN 0x00000004
+#define USP_HPSIR_EN 0x00000008
+#define USP_ENDIAN_CTRL_LSBF 0x00000010
+#define USP_EN 0x00000020
+#define USP_RXD_ACT_EDGE_FALLING 0x00000040
+#define USP_TXD_ACT_EDGE_FALLING 0x00000080
+#define USP_RFS_ACT_LEVEL_LOGIC1 0x00000100
+#define USP_TFS_ACT_LEVEL_LOGIC1 0x00000200
+#define USP_SCLK_IDLE_MODE_TOGGLE 0x00000400
+#define USP_SCLK_IDLE_LEVEL_LOGIC1 0x00000800
+#define USP_SCLK_PIN_MODE_IO 0x00001000
+#define USP_RFS_PIN_MODE_IO 0x00002000
+#define USP_TFS_PIN_MODE_IO 0x00004000
+#define USP_RXD_PIN_MODE_IO 0x00008000
+#define USP_TXD_PIN_MODE_IO 0x00010000
+#define USP_SCLK_IO_MODE_INPUT 0x00020000
+#define USP_RFS_IO_MODE_INPUT 0x00040000
+#define USP_TFS_IO_MODE_INPUT 0x00080000
+#define USP_RXD_IO_MODE_INPUT 0x00100000
+#define USP_TXD_IO_MODE_INPUT 0x00200000
+#define USP_IRDA_WIDTH_DIV_MASK 0x3FC00000
+#define USP_IRDA_WIDTH_DIV_OFFSET 0
+#define USP_IRDA_IDLE_LEVEL_HIGH 0x40000000
+#define USP_TX_UFLOW_REPEAT_ZERO 0x80000000
+#define USP_TX_ENDIAN_MODE 0x00000020
+#define USP_RX_ENDIAN_MODE 0x00000020
+
+/* USP Mode Register-2 */
+#define USP_RXD_DELAY_LEN_MASK 0x000000FF
+#define USP_RXD_DELAY_LEN_OFFSET 0
+
+#define USP_TXD_DELAY_LEN_MASK 0x0000FF00
+#define USP_TXD_DELAY_LEN_OFFSET 8
+
+#define USP_ENA_CTRL_MODE 0x00010000
+#define USP_FRAME_CTRL_MODE 0x00020000
+#define USP_TFS_SOURCE_MODE 0x00040000
+#define USP_TFS_MS_MODE 0x00080000
+#define USP_CLK_DIVISOR_MASK 0x7FE00000
+#define USP_CLK_DIVISOR_OFFSET 21
+
+#define USP_TFS_CLK_SLAVE_MODE (1<<20)
+#define USP_RFS_CLK_SLAVE_MODE (1<<19)
+
+#define USP_IRDA_DATA_WIDTH 0x80000000
+
+/* USP Transmit Frame Control Register */
+
+#define USP_TXC_DATA_LEN_MASK 0x000000FF
+#define USP_TXC_DATA_LEN_OFFSET 0
+
+#define USP_TXC_SYNC_LEN_MASK 0x0000FF00
+#define USP_TXC_SYNC_LEN_OFFSET 8
+
+#define USP_TXC_FRAME_LEN_MASK 0x00FF0000
+#define USP_TXC_FRAME_LEN_OFFSET 16
+
+#define USP_TXC_SHIFTER_LEN_MASK 0x1F000000
+#define USP_TXC_SHIFTER_LEN_OFFSET 24
+
+#define USP_TXC_SLAVE_CLK_SAMPLE 0x20000000
+
+#define USP_TXC_CLK_DIVISOR_MASK 0xC0000000
+#define USP_TXC_CLK_DIVISOR_OFFSET 30
+
+/* USP Receive Frame Control Register */
+
+#define USP_RXC_DATA_LEN_MASK 0x000000FF
+#define USP_RXC_DATA_LEN_OFFSET 0
+
+#define USP_RXC_FRAME_LEN_MASK 0x0000FF00
+#define USP_RXC_FRAME_LEN_OFFSET 8
+
+#define USP_RXC_SHIFTER_LEN_MASK 0x001F0000
+#define USP_RXC_SHIFTER_LEN_OFFSET 16
+
+#define USP_I2S_SYNC_CHG 0x00200000
+
+#define USP_RXC_CLK_DIVISOR_MASK 0x0F000000
+#define USP_RXC_CLK_DIVISOR_OFFSET 24
+#define USP_SINGLE_SYNC_MODE 0x00400000
+
+/* Tx - RX Enable Register */
+
+#define USP_RX_ENA 0x00000001
+#define USP_TX_ENA 0x00000002
+
+/* USP Interrupt Enable and status Register */
+#define USP_RX_DONE_INT 0x00000001
+#define USP_TX_DONE_INT 0x00000002
+#define USP_RX_OFLOW_INT 0x00000004
+#define USP_TX_UFLOW_INT 0x00000008
+#define USP_RX_IO_DMA_INT 0x00000010
+#define USP_TX_IO_DMA_INT 0x00000020
+#define USP_RXFIFO_FULL_INT 0x00000040
+#define USP_TXFIFO_EMPTY_INT 0x00000080
+#define USP_RXFIFO_THD_INT 0x00000100
+#define USP_TXFIFO_THD_INT 0x00000200
+#define USP_UART_FRM_ERR_INT 0x00000400
+#define USP_RX_TIMEOUT_INT 0x00000800
+#define USP_TX_ALLOUT_INT 0x00001000
+#define USP_RXD_BREAK_INT 0x00008000
+
+/* All possible TX interruots */
+#define USP_TX_INTERRUPT (USP_TX_DONE_INT|USP_TX_UFLOW_INT|\
+ USP_TX_IO_DMA_INT|\
+ USP_TXFIFO_EMPTY_INT|\
+ USP_TXFIFO_THD_INT)
+/* All possible RX interruots */
+#define USP_RX_INTERRUPT (USP_RX_DONE_INT|USP_RX_OFLOW_INT|\
+ USP_RX_IO_DMA_INT|\
+ USP_RXFIFO_FULL_INT|\
+ USP_RXFIFO_THD_INT|\
+ USP_RXFIFO_THD_INT|USP_RX_TIMEOUT_INT)
+
+#define USP_INT_ALL 0x1FFF
+
+/* USP Pin I/O Data Register */
+
+#define USP_RFS_PIN_VALUE_MASK 0x00000001
+#define USP_TFS_PIN_VALUE_MASK 0x00000002
+#define USP_RXD_PIN_VALUE_MASK 0x00000004
+#define USP_TXD_PIN_VALUE_MASK 0x00000008
+#define USP_SCLK_PIN_VALUE_MASK 0x00000010
+
+/* USP RISC/DSP Mode Register */
+#define USP_RISC_DSP_SEL 0x00000001
+
+/* USP ASYNC PARAMETER Register*/
+
+#define USP_ASYNC_TIMEOUT_MASK 0x0000FFFF
+#define USP_ASYNC_TIMEOUT_OFFSET 0
+#define USP_ASYNC_TIMEOUT(x) (((x)&USP_ASYNC_TIMEOUT_MASK)<<USP_ASYNC_TIMEOUT_OFFSET)
+
+#define USP_ASYNC_DIV2_MASK 0x003F0000
+#define USP_ASYNC_DIV2_OFFSET 16
+
+/* USP TX DMA I/O MODE Register */
+#define USP_TX_MODE_IO 0x00000001
+
+/* USP TX DMA I/O Length Register */
+#define USP_TX_DATA_LEN_MASK 0xFFFFFFFF
+#define USP_TX_DATA_LEN_OFFSET 0
+
+/* USP TX FIFO Control Register */
+#define USP_TX_FIFO_WIDTH_MASK 0x00000003
+#define USP_TX_FIFO_WIDTH_OFFSET 0
+
+#define USP_TX_FIFO_THD_MASK 0x000001FC
+#define USP_TX_FIFO_THD_OFFSET 2
+
+/* USP TX FIFO Level Check Register */
+#define USP_TX_FIFO_LEVEL_CHECK_MASK 0x1F
+#define USP_TX_FIFO_SC_OFFSET 0
+#define USP_TX_FIFO_LC_OFFSET 10
+#define USP_TX_FIFO_HC_OFFSET 20
+
+#define TX_FIFO_SC(x) (((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) << USP_TX_FIFO_SC_OFFSET)
+#define TX_FIFO_LC(x) (((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) << USP_TX_FIFO_LC_OFFSET)
+#define TX_FIFO_HC(x) (((x) & USP_TX_FIFO_LEVEL_CHECK_MASK) << USP_TX_FIFO_HC_OFFSET)
+
+/* USP TX FIFO Operation Register */
+#define USP_TX_FIFO_RESET 0x00000001
+#define USP_TX_FIFO_START 0x00000002
+
+/* USP TX FIFO Status Register */
+#define USP_TX_FIFO_LEVEL_MASK 0x0000007F
+#define USP_TX_FIFO_LEVEL_OFFSET 0
+
+#define USP_TX_FIFO_FULL 0x00000080
+#define USP_TX_FIFO_EMPTY 0x00000100
+
+/* USP TX FIFO Data Register */
+#define USP_TX_FIFO_DATA_MASK 0xFFFFFFFF
+#define USP_TX_FIFO_DATA_OFFSET 0
+
+/* USP RX DMA I/O MODE Register */
+#define USP_RX_MODE_IO 0x00000001
+#define USP_RX_DMA_FLUSH 0x00000004
+
+/* USP RX DMA I/O Length Register */
+#define USP_RX_DATA_LEN_MASK 0xFFFFFFFF
+#define USP_RX_DATA_LEN_OFFSET 0
+
+/* USP RX FIFO Control Register */
+#define USP_RX_FIFO_WIDTH_MASK 0x00000003
+#define USP_RX_FIFO_WIDTH_OFFSET 0
+
+#define USP_RX_FIFO_THD_MASK 0x000001FC
+#define USP_RX_FIFO_THD_OFFSET 2
+
+/* USP RX FIFO Level Check Register */
+
+#define USP_RX_FIFO_LEVEL_CHECK_MASK 0x1F
+#define USP_RX_FIFO_SC_OFFSET 0
+#define USP_RX_FIFO_LC_OFFSET 10
+#define USP_RX_FIFO_HC_OFFSET 20
+
+#define RX_FIFO_SC(x) (((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) << USP_RX_FIFO_SC_OFFSET)
+#define RX_FIFO_LC(x) (((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) << USP_RX_FIFO_LC_OFFSET)
+#define RX_FIFO_HC(x) (((x) & USP_RX_FIFO_LEVEL_CHECK_MASK) << USP_RX_FIFO_HC_OFFSET)
+
+/* USP RX FIFO Operation Register */
+#define USP_RX_FIFO_RESET 0x00000001
+#define USP_RX_FIFO_START 0x00000002
+
+/* USP RX FIFO Status Register */
+
+#define USP_RX_FIFO_LEVEL_MASK 0x0000007F
+#define USP_RX_FIFO_LEVEL_OFFSET 0
+
+#define USP_RX_FIFO_FULL 0x00000080
+#define USP_RX_FIFO_EMPTY 0x00000100
+
+/* USP RX FIFO Data Register */
+
+#define USP_RX_FIFO_DATA_MASK 0xFFFFFFFF
+#define USP_RX_FIFO_DATA_OFFSET 0
+
+/*
+ * When rx thd irq occur, sender just disable tx empty irq,
+ * Remaining data in tx fifo wil also be sent out.
+ */
+#define USP_FIFO_SIZE 128
+#define USP_TX_FIFO_THRESHOLD (USP_FIFO_SIZE/2)
+#define USP_RX_FIFO_THRESHOLD (USP_FIFO_SIZE/2)
+
+/* FIFO_WIDTH for the USP_TX_FIFO_CTRL and USP_RX_FIFO_CTRL registers */
+#define USP_FIFO_WIDTH_BYTE 0x00
+#define USP_FIFO_WIDTH_WORD 0x01
+#define USP_FIFO_WIDTH_DWORD 0x02
+
+#define USP_ASYNC_DIV2 16
+
+#define USP_PLUGOUT_RETRY_CNT 2
+
+#define USP_TX_RX_FIFO_WIDTH_DWORD 2
+
+#define SIRF_USP_DIV_MCLK 0
+#endif