@@ -2001,6 +2001,11 @@ static int cafe_pci_probe(struct pci_dev *pdev,
.min_width = 320,
.min_height = 240,
};
+ struct i2c_board_info ov7670_info = {
+ .type = "ov7670",
+ .addr = 0x42,
+ .platform_data = &sensor_cfg,
+ };
/*
* Start putting together one of our big camera structures.
@@ -2062,9 +2067,9 @@ static int cafe_pci_probe(struct pci_dev *pdev,
if (dmi_check_system(olpc_xo1_dmi))
sensor_cfg.clock_speed = 45;
- cam->sensor_addr = 0x42;
- cam->sensor = v4l2_i2c_new_subdev_cfg(&cam->v4l2_dev, &cam->i2c_adapter,
- "ov7670", 0, &sensor_cfg, cam->sensor_addr, NULL);
+ cam->sensor_addr = ov7670_info.addr;
+ cam->sensor = v4l2_i2c_new_subdev_board(&cam->v4l2_dev, &cam->i2c_adapter,
+ &ov7670_info, NULL);
if (cam->sensor == NULL) {
ret = -ENODEV;
goto out_smbus;
@@ -1682,20 +1682,6 @@ static int cx25840_log_status(struct v4l2_subdev *sd)
return 0;
}
-static int cx25840_s_config(struct v4l2_subdev *sd, int irq, void *platform_data)
-{
- struct cx25840_state *state = to_state(sd);
- struct i2c_client *client = v4l2_get_subdevdata(sd);
-
- if (platform_data) {
- struct cx25840_platform_data *pdata = platform_data;
-
- state->pvr150_workaround = pdata->pvr150_workaround;
- set_input(client, state->vid_input, state->aud_input);
- }
- return 0;
-}
-
static int cx23885_irq_handler(struct v4l2_subdev *sd, u32 status,
bool *handled)
{
@@ -1787,7 +1773,6 @@ static const struct v4l2_ctrl_ops cx25840_ctrl_ops = {
static const struct v4l2_subdev_core_ops cx25840_core_ops = {
.log_status = cx25840_log_status,
- .s_config = cx25840_s_config,
.g_chip_ident = cx25840_g_chip_ident,
.g_ctrl = v4l2_subdev_g_ctrl,
.s_ctrl = v4l2_subdev_s_ctrl,
@@ -1974,7 +1959,6 @@ static int cx25840_probe(struct i2c_client *client,
state->vid_input = CX25840_COMPOSITE7;
state->aud_input = CX25840_AUDIO8;
state->audclk_freq = 48000;
- state->pvr150_workaround = 0;
state->audmode = V4L2_TUNER_MODE_LANG1;
state->vbi_line_offset = 8;
state->id = id;
@@ -2019,6 +2003,12 @@ static int cx25840_probe(struct i2c_client *client,
v4l2_ctrl_cluster(2, &state->volume);
v4l2_ctrl_handler_setup(&state->hdl);
+ if (client->dev.platform_data) {
+ struct cx25840_platform_data *pdata = client->dev.platform_data;
+
+ state->pvr150_workaround = pdata->pvr150_workaround;
+ }
+
cx25840_ir_probe(sd);
return 0;
}
@@ -33,6 +33,7 @@
#include <media/saa7115.h>
#include <media/tvp5150.h>
#include <media/tvaudio.h>
+#include <media/mt9v011.h>
#include <media/i2c-addr.h>
#include <media/tveeprom.h>
#include <media/v4l2-common.h>
@@ -1917,11 +1918,6 @@ static unsigned short tvp5150_addrs[] = {
I2C_CLIENT_END
};
-static unsigned short mt9v011_addrs[] = {
- 0xba >> 1,
- I2C_CLIENT_END
-};
-
static unsigned short msp3400_addrs[] = {
0x80 >> 1,
0x88 >> 1,
@@ -2623,11 +2619,17 @@ void em28xx_card_setup(struct em28xx *dev)
"tvp5150", 0, tvp5150_addrs);
if (dev->em28xx_sensor == EM28XX_MT9V011) {
+ struct mt9v011_platform_data pdata;
+ struct i2c_board_info mt9v011_info = {
+ .type = "mt9v011",
+ .addr = 0xba >> 1,
+ .platform_data = &pdata,
+ };
struct v4l2_subdev *sd;
- sd = v4l2_i2c_new_subdev(&dev->v4l2_dev,
- &dev->i2c_adap, "mt9v011", 0, mt9v011_addrs);
- v4l2_subdev_call(sd, core, s_config, 0, &dev->sensor_xtal);
+ pdata.xtal = dev->sensor_xtal;
+ sd = v4l2_i2c_new_subdev_board(&dev->v4l2_dev, &dev->i2c_adap,
+ &mt9v011_info, NULL);
}
@@ -300,10 +300,15 @@ int ivtv_i2c_register(struct ivtv *itv, unsigned idx)
adap, type, 0, I2C_ADDRS(hw_addrs[idx]));
} else if (hw == IVTV_HW_CX25840) {
struct cx25840_platform_data pdata;
+ struct i2c_board_info cx25840_info = {
+ .type = "cx25840",
+ .addr = hw_addrs[idx],
+ .platform_data = &pdata,
+ };
pdata.pvr150_workaround = itv->pvr150_workaround;
- sd = v4l2_i2c_new_subdev_cfg(&itv->v4l2_dev,
- adap, type, 0, &pdata, hw_addrs[idx], NULL);
+ sd = v4l2_i2c_new_subdev_board(&itv->v4l2_dev, adap,
+ &cx25840_info, NULL);
} else {
sd = v4l2_i2c_new_subdev(&itv->v4l2_dev,
adap, type, hw_addrs[idx], NULL);
@@ -12,17 +12,41 @@
#include <asm/div64.h>
#include <media/v4l2-device.h>
#include <media/v4l2-chip-ident.h>
-#include "mt9v011.h"
+#include <media/mt9v011.h>
MODULE_DESCRIPTION("Micron mt9v011 sensor driver");
MODULE_AUTHOR("Mauro Carvalho Chehab <mchehab@redhat.com>");
MODULE_LICENSE("GPL");
-
static int debug;
module_param(debug, int, 0);
MODULE_PARM_DESC(debug, "Debug level (0-2)");
+#define R00_MT9V011_CHIP_VERSION 0x00
+#define R01_MT9V011_ROWSTART 0x01
+#define R02_MT9V011_COLSTART 0x02
+#define R03_MT9V011_HEIGHT 0x03
+#define R04_MT9V011_WIDTH 0x04
+#define R05_MT9V011_HBLANK 0x05
+#define R06_MT9V011_VBLANK 0x06
+#define R07_MT9V011_OUT_CTRL 0x07
+#define R09_MT9V011_SHUTTER_WIDTH 0x09
+#define R0A_MT9V011_CLK_SPEED 0x0a
+#define R0B_MT9V011_RESTART 0x0b
+#define R0C_MT9V011_SHUTTER_DELAY 0x0c
+#define R0D_MT9V011_RESET 0x0d
+#define R1E_MT9V011_DIGITAL_ZOOM 0x1e
+#define R20_MT9V011_READ_MODE 0x20
+#define R2B_MT9V011_GREEN_1_GAIN 0x2b
+#define R2C_MT9V011_BLUE_GAIN 0x2c
+#define R2D_MT9V011_RED_GAIN 0x2d
+#define R2E_MT9V011_GREEN_2_GAIN 0x2e
+#define R35_MT9V011_GLOBAL_GAIN 0x35
+#define RF1_MT9V011_CHIP_ENABLE 0xf1
+
+#define MT9V011_VERSION 0x8232
+#define MT9V011_REV_B_VERSION 0x8243
+
/* supported controls */
static struct v4l2_queryctrl mt9v011_qctrl[] = {
{
@@ -469,23 +493,6 @@ static int mt9v011_s_mbus_fmt(struct v4l2_subdev *sd, struct v4l2_mbus_framefmt
return 0;
}
-static int mt9v011_s_config(struct v4l2_subdev *sd, int dumb, void *data)
-{
- struct mt9v011 *core = to_mt9v011(sd);
- unsigned *xtal = data;
-
- v4l2_dbg(1, debug, sd, "s_config called\n");
-
- if (xtal) {
- core->xtal = *xtal;
- v4l2_dbg(1, debug, sd, "xtal set to %d.%03d MHz\n",
- *xtal / 1000000, (*xtal / 1000) % 1000);
- }
-
- return 0;
-}
-
-
#ifdef CONFIG_VIDEO_ADV_DEBUG
static int mt9v011_g_register(struct v4l2_subdev *sd,
struct v4l2_dbg_register *reg)
@@ -536,7 +543,6 @@ static const struct v4l2_subdev_core_ops mt9v011_core_ops = {
.g_ctrl = mt9v011_g_ctrl,
.s_ctrl = mt9v011_s_ctrl,
.reset = mt9v011_reset,
- .s_config = mt9v011_s_config,
.g_chip_ident = mt9v011_g_chip_ident,
#ifdef CONFIG_VIDEO_ADV_DEBUG
.g_register = mt9v011_g_register,
@@ -596,6 +602,14 @@ static int mt9v011_probe(struct i2c_client *c,
core->height = 480;
core->xtal = 27000000; /* Hz */
+ if (c->dev.platform_data) {
+ struct mt9v011_platform_data *pdata = c->dev.platform_data;
+
+ core->xtal = pdata->xtal;
+ v4l2_dbg(1, debug, sd, "xtal set to %d.%03d MHz\n",
+ core->xtal / 1000000, (core->xtal / 1000) % 1000);
+ }
+
v4l_info(c, "chip found @ 0x%02x (%s - chip version 0x%04x)\n",
c->addr << 1, c->adapter->name, version);
deleted file mode 100644
@@ -1,36 +0,0 @@
-/*
- * mt9v011 -Micron 1/4-Inch VGA Digital Image Sensor
- *
- * Copyright (c) 2009 Mauro Carvalho Chehab (mchehab@redhat.com)
- * This code is placed under the terms of the GNU General Public License v2
- */
-
-#ifndef MT9V011_H_
-#define MT9V011_H_
-
-#define R00_MT9V011_CHIP_VERSION 0x00
-#define R01_MT9V011_ROWSTART 0x01
-#define R02_MT9V011_COLSTART 0x02
-#define R03_MT9V011_HEIGHT 0x03
-#define R04_MT9V011_WIDTH 0x04
-#define R05_MT9V011_HBLANK 0x05
-#define R06_MT9V011_VBLANK 0x06
-#define R07_MT9V011_OUT_CTRL 0x07
-#define R09_MT9V011_SHUTTER_WIDTH 0x09
-#define R0A_MT9V011_CLK_SPEED 0x0a
-#define R0B_MT9V011_RESTART 0x0b
-#define R0C_MT9V011_SHUTTER_DELAY 0x0c
-#define R0D_MT9V011_RESET 0x0d
-#define R1E_MT9V011_DIGITAL_ZOOM 0x1e
-#define R20_MT9V011_READ_MODE 0x20
-#define R2B_MT9V011_GREEN_1_GAIN 0x2b
-#define R2C_MT9V011_BLUE_GAIN 0x2c
-#define R2D_MT9V011_RED_GAIN 0x2d
-#define R2E_MT9V011_GREEN_2_GAIN 0x2e
-#define R35_MT9V011_GLOBAL_GAIN 0x35
-#define RF1_MT9V011_CHIP_ENABLE 0xf1
-
-#define MT9V011_VERSION 0x8232
-#define MT9V011_REV_B_VERSION 0x8243
-
-#endif
@@ -1449,47 +1449,6 @@ static int ov7670_g_chip_ident(struct v4l2_subdev *sd,
return v4l2_chip_ident_i2c_client(client, chip, V4L2_IDENT_OV7670, 0);
}
-static int ov7670_s_config(struct v4l2_subdev *sd, int dumb, void *data)
-{
- struct i2c_client *client = v4l2_get_subdevdata(sd);
- struct ov7670_config *config = data;
- struct ov7670_info *info = to_state(sd);
- int ret;
-
- info->clock_speed = 30; /* default: a guess */
-
- /*
- * Must apply configuration before initializing device, because it
- * selects I/O method.
- */
- if (config) {
- info->min_width = config->min_width;
- info->min_height = config->min_height;
- info->use_smbus = config->use_smbus;
-
- if (config->clock_speed)
- info->clock_speed = config->clock_speed;
- }
-
- /* Make sure it's an ov7670 */
- ret = ov7670_detect(sd);
- if (ret) {
- v4l_dbg(1, debug, client,
- "chip found @ 0x%x (%s) is not an ov7670 chip.\n",
- client->addr << 1, client->adapter->name);
- kfree(info);
- return ret;
- }
- v4l_info(client, "chip found @ 0x%02x (%s)\n",
- client->addr << 1, client->adapter->name);
-
- info->fmt = &ov7670_formats[0];
- info->sat = 128; /* Review this */
- info->clkrc = info->clock_speed / 30;
-
- return 0;
-}
-
#ifdef CONFIG_VIDEO_ADV_DEBUG
static int ov7670_g_register(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg)
{
@@ -1528,7 +1487,6 @@ static const struct v4l2_subdev_core_ops ov7670_core_ops = {
.s_ctrl = ov7670_s_ctrl,
.queryctrl = ov7670_queryctrl,
.reset = ov7670_reset,
- .s_config = ov7670_s_config,
.init = ov7670_init,
#ifdef CONFIG_VIDEO_ADV_DEBUG
.g_register = ov7670_g_register,
@@ -1558,6 +1516,7 @@ static int ov7670_probe(struct i2c_client *client,
{
struct v4l2_subdev *sd;
struct ov7670_info *info;
+ int ret;
info = kzalloc(sizeof(struct ov7670_info), GFP_KERNEL);
if (info == NULL)
@@ -1565,6 +1524,37 @@ static int ov7670_probe(struct i2c_client *client,
sd = &info->sd;
v4l2_i2c_subdev_init(sd, client, &ov7670_ops);
+ info->clock_speed = 30; /* default: a guess */
+ if (client->dev.platform_data) {
+ struct ov7670_config *config = client->dev.platform_data;
+
+ /*
+ * Must apply configuration before initializing device, because it
+ * selects I/O method.
+ */
+ info->min_width = config->min_width;
+ info->min_height = config->min_height;
+ info->use_smbus = config->use_smbus;
+
+ if (config->clock_speed)
+ info->clock_speed = config->clock_speed;
+ }
+
+ /* Make sure it's an ov7670 */
+ ret = ov7670_detect(sd);
+ if (ret) {
+ v4l_dbg(1, debug, client,
+ "chip found @ 0x%x (%s) is not an ov7670 chip.\n",
+ client->addr << 1, client->adapter->name);
+ kfree(info);
+ return ret;
+ }
+ v4l_info(client, "chip found @ 0x%02x (%s)\n",
+ client->addr << 1, client->adapter->name);
+
+ info->fmt = &ov7670_formats[0];
+ info->sat = 128; /* Review this */
+ info->clkrc = info->clock_speed / 30;
return 0;
}
@@ -714,15 +714,6 @@ static int sr030pc30_base_config(struct v4l2_subdev *sd)
return ret;
}
-static int sr030pc30_s_config(struct v4l2_subdev *sd,
- int irq, void *platform_data)
-{
- struct sr030pc30_info *info = to_sr030pc30(sd);
-
- info->pdata = platform_data;
- return 0;
-}
-
static int sr030pc30_s_stream(struct v4l2_subdev *sd, int enable)
{
return 0;
@@ -763,7 +754,6 @@ static int sr030pc30_s_power(struct v4l2_subdev *sd, int on)
}
static const struct v4l2_subdev_core_ops sr030pc30_core_ops = {
- .s_config = sr030pc30_s_config,
.s_power = sr030pc30_s_power,
.queryctrl = sr030pc30_queryctrl,
.s_ctrl = sr030pc30_s_ctrl,
@@ -407,18 +407,6 @@ struct v4l2_subdev *v4l2_i2c_new_subdev_board(struct v4l2_device *v4l2_dev,
/* Decrease the module use count to match the first try_module_get. */
module_put(client->driver->driver.owner);
- if (sd) {
- /* We return errors from v4l2_subdev_call only if we have the
- callback as the .s_config is not mandatory */
- int err = v4l2_subdev_call(sd, core, s_config,
- info->irq, info->platform_data);
-
- if (err && err != -ENOIOCTLCMD) {
- v4l2_device_unregister_subdev(sd);
- sd = NULL;
- }
- }
-
error:
/* If we have a client but no subdev, then something went wrong and
we must unregister the client. */
@@ -428,9 +416,8 @@ error:
}
EXPORT_SYMBOL_GPL(v4l2_i2c_new_subdev_board);
-struct v4l2_subdev *v4l2_i2c_new_subdev_cfg(struct v4l2_device *v4l2_dev,
+struct v4l2_subdev *v4l2_i2c_new_subdev(struct v4l2_device *v4l2_dev,
struct i2c_adapter *adapter, const char *client_type,
- int irq, void *platform_data,
u8 addr, const unsigned short *probe_addrs)
{
struct i2c_board_info info;
@@ -440,12 +427,10 @@ struct v4l2_subdev *v4l2_i2c_new_subdev_cfg(struct v4l2_device *v4l2_dev,
memset(&info, 0, sizeof(info));
strlcpy(info.type, client_type, sizeof(info.type));
info.addr = addr;
- info.irq = irq;
- info.platform_data = platform_data;
return v4l2_i2c_new_subdev_board(v4l2_dev, adapter, &info, probe_addrs);
}
-EXPORT_SYMBOL_GPL(v4l2_i2c_new_subdev_cfg);
+EXPORT_SYMBOL_GPL(v4l2_i2c_new_subdev);
/* Return i2c client address of v4l2_subdev. */
unsigned short v4l2_i2c_subdev_addr(struct v4l2_subdev *sd)
new file mode 100644
@@ -0,0 +1,17 @@
+/* mt9v011 sensor
+ *
+ * Copyright (C) 2011 Hans Verkuil <hverkuil@xs4all.nl>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MT9V011_H__
+#define __MT9V011_H__
+
+struct mt9v011_platform_data {
+ unsigned xtal; /* Hz */
+};
+
+#endif
@@ -138,21 +138,10 @@ struct v4l2_subdev_ops;
/* Load an i2c module and return an initialized v4l2_subdev struct.
The client_type argument is the name of the chip that's on the adapter. */
-struct v4l2_subdev *v4l2_i2c_new_subdev_cfg(struct v4l2_device *v4l2_dev,
+struct v4l2_subdev *v4l2_i2c_new_subdev(struct v4l2_device *v4l2_dev,
struct i2c_adapter *adapter, const char *client_type,
- int irq, void *platform_data,
u8 addr, const unsigned short *probe_addrs);
-/* Load an i2c module and return an initialized v4l2_subdev struct.
- The client_type argument is the name of the chip that's on the adapter. */
-static inline struct v4l2_subdev *v4l2_i2c_new_subdev(struct v4l2_device *v4l2_dev,
- struct i2c_adapter *adapter, const char *client_type,
- u8 addr, const unsigned short *probe_addrs)
-{
- return v4l2_i2c_new_subdev_cfg(v4l2_dev, adapter, client_type, 0, NULL,
- addr, probe_addrs);
-}
-
struct i2c_board_info;
struct v4l2_subdev *v4l2_i2c_new_subdev_board(struct v4l2_device *v4l2_dev,
@@ -106,10 +106,7 @@ struct v4l2_subdev_io_pin_config {
u8 strength; /* Pin drive strength */
};
-/* s_config: if set, then it is always called by the v4l2_i2c_new_subdev*
- functions after the v4l2_subdev was registered. It is used to pass
- platform data to the subdev which can be used during initialization.
-
+/*
s_io_pin_config: configure one or more chip I/O pins for chips that
multiplex different internal signal pads out to IO pins. This function
takes a pointer to an array of 'n' pin configuration entries, one for
@@ -141,7 +138,6 @@ struct v4l2_subdev_io_pin_config {
struct v4l2_subdev_core_ops {
int (*g_chip_ident)(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip);
int (*log_status)(struct v4l2_subdev *sd);
- int (*s_config)(struct v4l2_subdev *sd, int irq, void *platform_data);
int (*s_io_pin_config)(struct v4l2_subdev *sd, size_t n,
struct v4l2_subdev_io_pin_config *pincfg);
int (*init)(struct v4l2_subdev *sd, u32 val);