[2/5] input: touchscreen: ti_am335x_tsc: Remove udelay in interrupt handler
diff mbox

Message ID 1415339350-17679-3-git-send-email-vigneshr@ti.com
State New, archived
Headers show

Commit Message

Vignesh Raghavendra Nov. 7, 2014, 5:49 a.m. UTC
From: Brad Griffis <bgriffis@ti.com>

TSC interrupt handler had udelay to avoid reporting of false pen-up
interrupt to user space. This patch implements workaround suggesting in
Advisory 1.0.31 of silicon errata for am335x, thus eliminating udelay
and touchscreen lag. This also improves performance of touchscreen and
eliminates sudden jump of cursor at touch release.

IDLECONFIG and CHARGECONFIG registers are to be configured
with same values in order to eliminate false pen-up events. This
workaround may result in false pen-down to be detected, hence considerable
charge step delay needs to be added. The charge delay is set to 0xB000
(in terms of ADC clock cycles) by default.

TSC steps are disabled at the end of every sampling cycle and EOS bit is
set. Once the EOS bit is set, the TSC steps need to be re-enabled to begin
next sampling cycle.

Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.18rc2]

Signed-off-by: Vignesh R <vigneshr@ti.com>
---
 drivers/input/touchscreen/ti_am335x_tsc.c | 56 ++++++++++++-------------------
 include/linux/mfd/ti_am335x_tscadc.h      |  3 +-
 2 files changed, 24 insertions(+), 35 deletions(-)

Comments

Lee Jones Nov. 10, 2014, 9:11 a.m. UTC | #1
On Fri, 07 Nov 2014, Vignesh R wrote:

> From: Brad Griffis <bgriffis@ti.com>
> 
> TSC interrupt handler had udelay to avoid reporting of false pen-up
> interrupt to user space. This patch implements workaround suggesting in
> Advisory 1.0.31 of silicon errata for am335x, thus eliminating udelay
> and touchscreen lag. This also improves performance of touchscreen and
> eliminates sudden jump of cursor at touch release.
> 
> IDLECONFIG and CHARGECONFIG registers are to be configured
> with same values in order to eliminate false pen-up events. This
> workaround may result in false pen-down to be detected, hence considerable
> charge step delay needs to be added. The charge delay is set to 0xB000
> (in terms of ADC clock cycles) by default.
> 
> TSC steps are disabled at the end of every sampling cycle and EOS bit is
> set. Once the EOS bit is set, the TSC steps need to be re-enabled to begin
> next sampling cycle.
> 
> Signed-off-by: Brad Griffis <bgriffis@ti.com>
> [vigneshr@ti.com: Ported the patch from v3.12 to v3.18rc2]
> 
> Signed-off-by: Vignesh R <vigneshr@ti.com>
> ---
>  drivers/input/touchscreen/ti_am335x_tsc.c | 56 ++++++++++++-------------------
>  include/linux/mfd/ti_am335x_tscadc.h      |  3 +-

Acked-by: Lee Jones <lee.jones@linaro.org>

>  2 files changed, 24 insertions(+), 35 deletions(-)
> 
> diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
> index 1aeac9675fe7..483fd97c0e0c 100644
> --- a/drivers/input/touchscreen/ti_am335x_tsc.c
> +++ b/drivers/input/touchscreen/ti_am335x_tsc.c
> @@ -173,11 +173,9 @@ static void titsc_step_config(struct titsc *ts_dev)
>  		titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
>  	}
>  
> -	/* Charge step configuration */
> -	config = ts_dev->bit_xp | ts_dev->bit_yn |
> -			STEPCHARGE_RFP_XPUL | STEPCHARGE_RFM_XNUR |
> -			STEPCHARGE_INM_AN1 | STEPCHARGE_INP(ts_dev->inp_yp);
> +	/* Make CHARGECONFIG same as IDLECONFIG */
>  
> +	config = titsc_readl(ts_dev, REG_IDLECONFIG);
>  	titsc_writel(ts_dev, REG_CHARGECONFIG, config);
>  	titsc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
>  
> @@ -264,9 +262,26 @@ static irqreturn_t titsc_irq(int irq, void *dev)
>  	unsigned int status, irqclr = 0;
>  	unsigned int x = 0, y = 0;
>  	unsigned int z1, z2, z;
> -	unsigned int fsm;
>  
> -	status = titsc_readl(ts_dev, REG_IRQSTATUS);
> +	status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
> +	if (status & IRQENB_HW_PEN) {
> +		ts_dev->pen_down = true;
> +		titsc_writel(ts_dev, REG_IRQWAKEUP, 0x00);
> +		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
> +		irqclr |= IRQENB_HW_PEN;
> +	}
> +
> +	if (status & IRQENB_PENUP) {
> +		ts_dev->pen_down = false;
> +		input_report_key(input_dev, BTN_TOUCH, 0);
> +		input_report_abs(input_dev, ABS_PRESSURE, 0);
> +		input_sync(input_dev);
> +		irqclr |= IRQENB_PENUP;
> +	}
> +
> +	if (status & IRQENB_EOS)
> +		irqclr |= IRQENB_EOS;
> +
>  	/*
>  	 * ADC and touchscreen share the IRQ line.
>  	 * FIFO1 interrupts are used by ADC. Handle FIFO0 IRQs here only
> @@ -297,34 +312,6 @@ static irqreturn_t titsc_irq(int irq, void *dev)
>  		}
>  		irqclr |= IRQENB_FIFO0THRES;
>  	}
> -
> -	/*
> -	 * Time for sequencer to settle, to read
> -	 * correct state of the sequencer.
> -	 */
> -	udelay(SEQ_SETTLE);
> -
> -	status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
> -	if (status & IRQENB_PENUP) {
> -		/* Pen up event */
> -		fsm = titsc_readl(ts_dev, REG_ADCFSM);
> -		if (fsm == ADCFSM_STEPID) {
> -			ts_dev->pen_down = false;
> -			input_report_key(input_dev, BTN_TOUCH, 0);
> -			input_report_abs(input_dev, ABS_PRESSURE, 0);
> -			input_sync(input_dev);
> -		} else {
> -			ts_dev->pen_down = true;
> -		}
> -		irqclr |= IRQENB_PENUP;
> -	}
> -
> -	if (status & IRQENB_HW_PEN) {
> -
> -		titsc_writel(ts_dev, REG_IRQWAKEUP, 0x00);
> -		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
> -	}
> -
>  	if (irqclr) {
>  		titsc_writel(ts_dev, REG_IRQSTATUS, irqclr);
>  		am335x_tsc_se_set_cache(ts_dev->mfd_tscadc, ts_dev->step_mask);
> @@ -417,6 +404,7 @@ static int titsc_probe(struct platform_device *pdev)
>  	}
>  
>  	titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
> +	titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_EOS);
>  	err = titsc_config_wires(ts_dev);
>  	if (err) {
>  		dev_err(&pdev->dev, "wrong i/p wire configuration\n");
> diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
> index e2e70053470e..c99be5dc0f5c 100644
> --- a/include/linux/mfd/ti_am335x_tscadc.h
> +++ b/include/linux/mfd/ti_am335x_tscadc.h
> @@ -52,6 +52,7 @@
>  
>  /* IRQ enable */
>  #define IRQENB_HW_PEN		BIT(0)
> +#define IRQENB_EOS		BIT(1)
>  #define IRQENB_FIFO0THRES	BIT(2)
>  #define IRQENB_FIFO0OVRRUN	BIT(3)
>  #define IRQENB_FIFO0UNDRFLW	BIT(4)
> @@ -107,7 +108,7 @@
>  /* Charge delay */
>  #define CHARGEDLY_OPEN_MASK	(0x3FFFF << 0)
>  #define CHARGEDLY_OPEN(val)	((val) << 0)
> -#define CHARGEDLY_OPENDLY	CHARGEDLY_OPEN(1)
> +#define CHARGEDLY_OPENDLY	CHARGEDLY_OPEN(0xB000)
>  
>  /* Control register */
>  #define CNTRLREG_TSCSSENB	BIT(0)

Patch
diff mbox

diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index 1aeac9675fe7..483fd97c0e0c 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -173,11 +173,9 @@  static void titsc_step_config(struct titsc *ts_dev)
 		titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
 	}
 
-	/* Charge step configuration */
-	config = ts_dev->bit_xp | ts_dev->bit_yn |
-			STEPCHARGE_RFP_XPUL | STEPCHARGE_RFM_XNUR |
-			STEPCHARGE_INM_AN1 | STEPCHARGE_INP(ts_dev->inp_yp);
+	/* Make CHARGECONFIG same as IDLECONFIG */
 
+	config = titsc_readl(ts_dev, REG_IDLECONFIG);
 	titsc_writel(ts_dev, REG_CHARGECONFIG, config);
 	titsc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
 
@@ -264,9 +262,26 @@  static irqreturn_t titsc_irq(int irq, void *dev)
 	unsigned int status, irqclr = 0;
 	unsigned int x = 0, y = 0;
 	unsigned int z1, z2, z;
-	unsigned int fsm;
 
-	status = titsc_readl(ts_dev, REG_IRQSTATUS);
+	status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
+	if (status & IRQENB_HW_PEN) {
+		ts_dev->pen_down = true;
+		titsc_writel(ts_dev, REG_IRQWAKEUP, 0x00);
+		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
+		irqclr |= IRQENB_HW_PEN;
+	}
+
+	if (status & IRQENB_PENUP) {
+		ts_dev->pen_down = false;
+		input_report_key(input_dev, BTN_TOUCH, 0);
+		input_report_abs(input_dev, ABS_PRESSURE, 0);
+		input_sync(input_dev);
+		irqclr |= IRQENB_PENUP;
+	}
+
+	if (status & IRQENB_EOS)
+		irqclr |= IRQENB_EOS;
+
 	/*
 	 * ADC and touchscreen share the IRQ line.
 	 * FIFO1 interrupts are used by ADC. Handle FIFO0 IRQs here only
@@ -297,34 +312,6 @@  static irqreturn_t titsc_irq(int irq, void *dev)
 		}
 		irqclr |= IRQENB_FIFO0THRES;
 	}
-
-	/*
-	 * Time for sequencer to settle, to read
-	 * correct state of the sequencer.
-	 */
-	udelay(SEQ_SETTLE);
-
-	status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
-	if (status & IRQENB_PENUP) {
-		/* Pen up event */
-		fsm = titsc_readl(ts_dev, REG_ADCFSM);
-		if (fsm == ADCFSM_STEPID) {
-			ts_dev->pen_down = false;
-			input_report_key(input_dev, BTN_TOUCH, 0);
-			input_report_abs(input_dev, ABS_PRESSURE, 0);
-			input_sync(input_dev);
-		} else {
-			ts_dev->pen_down = true;
-		}
-		irqclr |= IRQENB_PENUP;
-	}
-
-	if (status & IRQENB_HW_PEN) {
-
-		titsc_writel(ts_dev, REG_IRQWAKEUP, 0x00);
-		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
-	}
-
 	if (irqclr) {
 		titsc_writel(ts_dev, REG_IRQSTATUS, irqclr);
 		am335x_tsc_se_set_cache(ts_dev->mfd_tscadc, ts_dev->step_mask);
@@ -417,6 +404,7 @@  static int titsc_probe(struct platform_device *pdev)
 	}
 
 	titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
+	titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_EOS);
 	err = titsc_config_wires(ts_dev);
 	if (err) {
 		dev_err(&pdev->dev, "wrong i/p wire configuration\n");
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
index e2e70053470e..c99be5dc0f5c 100644
--- a/include/linux/mfd/ti_am335x_tscadc.h
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -52,6 +52,7 @@ 
 
 /* IRQ enable */
 #define IRQENB_HW_PEN		BIT(0)
+#define IRQENB_EOS		BIT(1)
 #define IRQENB_FIFO0THRES	BIT(2)
 #define IRQENB_FIFO0OVRRUN	BIT(3)
 #define IRQENB_FIFO0UNDRFLW	BIT(4)
@@ -107,7 +108,7 @@ 
 /* Charge delay */
 #define CHARGEDLY_OPEN_MASK	(0x3FFFF << 0)
 #define CHARGEDLY_OPEN(val)	((val) << 0)
-#define CHARGEDLY_OPENDLY	CHARGEDLY_OPEN(1)
+#define CHARGEDLY_OPENDLY	CHARGEDLY_OPEN(0xB000)
 
 /* Control register */
 #define CNTRLREG_TSCSSENB	BIT(0)