[1/1] SPI S3C64XX: SPI Controller driver for S3C64XX
diff mbox

Message ID 1259566782-31232-1-git-send-email-jassisinghbrar@gmail.com
State Accepted
Headers show

Commit Message

Jassi Brar Nov. 30, 2009, 7:39 a.m. UTC
None

Patch
diff mbox

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 2c733c2..5c67e1e 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -204,6 +204,13 @@  config SPI_S3C24XX_GPIO
 	  the inbuilt hardware cannot provide the transfer mode, or
 	  where the board is using non hardware connected pins.
 
+config SPI_S3C64XX
+	tristate "Samsung S3C64XX series type SPI"
+	depends on ARCH_S3C64XX && EXPERIMENTAL
+	select S3C64XX_DMA
+	help
+	  SPI driver for Samsung S3C64XX and newer SoCs.
+
 config SPI_SH_SCI
 	tristate "SuperH SCI SPI controller"
 	depends on SUPERH
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 3de408d..53452b2 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -31,6 +31,7 @@  obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx.o
 obj-$(CONFIG_SPI_TXX9)			+= spi_txx9.o
 obj-$(CONFIG_SPI_XILINX)		+= xilinx_spi.o
 obj-$(CONFIG_SPI_SH_SCI)		+= spi_sh_sci.o
+obj-$(CONFIG_SPI_S3C64XX)		+= spi_s3c64xx.o
 # 	... add above this line ...
 
 # SPI protocol drivers (device/link on bus)
diff --git a/drivers/spi/spi_s3c64xx.c b/drivers/spi/spi_s3c64xx.c
new file mode 100644
index 0000000..88a456d
--- /dev/null
+++ b/drivers/spi/spi_s3c64xx.c
@@ -0,0 +1,1196 @@ 
+/* linux/drivers/spi/spi_s3c64xx.c
+ *
+ * Copyright (C) 2009 Samsung Electronics Ltd.
+ *	Jaswinder Singh <jassi.brar@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/workqueue.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include <mach/dma.h>
+#include <plat/spi.h>
+
+/* Registers and bit-fields */
+
+#define S3C64XX_SPI_CH_CFG		0x00
+#define S3C64XX_SPI_CLK_CFG		0x04
+#define S3C64XX_SPI_MODE_CFG	0x08
+#define S3C64XX_SPI_SLAVE_SEL	0x0C
+#define S3C64XX_SPI_INT_EN		0x10
+#define S3C64XX_SPI_STATUS		0x14
+#define S3C64XX_SPI_TX_DATA		0x18
+#define S3C64XX_SPI_RX_DATA		0x1C
+#define S3C64XX_SPI_PACKET_CNT	0x20
+#define S3C64XX_SPI_PENDING_CLR	0x24
+#define S3C64XX_SPI_SWAP_CFG	0x28
+#define S3C64XX_SPI_FB_CLK		0x2C
+
+#define S3C64XX_SPI_CH_HS_EN		(1<<6)	/* High Speed Enable */
+#define S3C64XX_SPI_CH_SW_RST		(1<<5)
+#define S3C64XX_SPI_CH_SLAVE		(1<<4)
+#define S3C64XX_SPI_CPOL_L		(1<<3)
+#define S3C64XX_SPI_CPHA_B		(1<<2)
+#define S3C64XX_SPI_CH_RXCH_ON		(1<<1)
+#define S3C64XX_SPI_CH_TXCH_ON		(1<<0)
+
+#define S3C64XX_SPI_CLKSEL_SRCMSK	(3<<9)
+#define S3C64XX_SPI_CLKSEL_SRCSHFT	9
+#define S3C64XX_SPI_ENCLK_ENABLE	(1<<8)
+#define S3C64XX_SPI_PSR_MASK 		0xff
+
+#define S3C64XX_SPI_MODE_CH_TSZ_BYTE		(0<<29)
+#define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD	(1<<29)
+#define S3C64XX_SPI_MODE_CH_TSZ_WORD		(2<<29)
+#define S3C64XX_SPI_MODE_CH_TSZ_MASK		(3<<29)
+#define S3C64XX_SPI_MODE_BUS_TSZ_BYTE		(0<<17)
+#define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD	(1<<17)
+#define S3C64XX_SPI_MODE_BUS_TSZ_WORD		(2<<17)
+#define S3C64XX_SPI_MODE_BUS_TSZ_MASK		(3<<17)
+#define S3C64XX_SPI_MODE_RXDMA_ON		(1<<2)
+#define S3C64XX_SPI_MODE_TXDMA_ON		(1<<1)
+#define S3C64XX_SPI_MODE_4BURST			(1<<0)
+
+#define S3C64XX_SPI_SLAVE_AUTO			(1<<1)
+#define S3C64XX_SPI_SLAVE_SIG_INACT		(1<<0)
+
+#define S3C64XX_SPI_ACT(c) writel(0, (c)->regs + S3C64XX_SPI_SLAVE_SEL)
+
+#define S3C64XX_SPI_DEACT(c) writel(S3C64XX_SPI_SLAVE_SIG_INACT, \
+					(c)->regs + S3C64XX_SPI_SLAVE_SEL)
+
+#define S3C64XX_SPI_INT_TRAILING_EN		(1<<6)
+#define S3C64XX_SPI_INT_RX_OVERRUN_EN		(1<<5)
+#define S3C64XX_SPI_INT_RX_UNDERRUN_EN		(1<<4)
+#define S3C64XX_SPI_INT_TX_OVERRUN_EN		(1<<3)
+#define S3C64XX_SPI_INT_TX_UNDERRUN_EN		(1<<2)
+#define S3C64XX_SPI_INT_RX_FIFORDY_EN		(1<<1)
+#define S3C64XX_SPI_INT_TX_FIFORDY_EN		(1<<0)
+
+#define S3C64XX_SPI_ST_RX_OVERRUN_ERR		(1<<5)
+#define S3C64XX_SPI_ST_RX_UNDERRUN_ERR	(1<<4)
+#define S3C64XX_SPI_ST_TX_OVERRUN_ERR		(1<<3)
+#define S3C64XX_SPI_ST_TX_UNDERRUN_ERR	(1<<2)
+#define S3C64XX_SPI_ST_RX_FIFORDY		(1<<1)
+#define S3C64XX_SPI_ST_TX_FIFORDY		(1<<0)
+
+#define S3C64XX_SPI_PACKET_CNT_EN		(1<<16)
+
+#define S3C64XX_SPI_PND_TX_UNDERRUN_CLR		(1<<4)
+#define S3C64XX_SPI_PND_TX_OVERRUN_CLR		(1<<3)
+#define S3C64XX_SPI_PND_RX_UNDERRUN_CLR		(1<<2)
+#define S3C64XX_SPI_PND_RX_OVERRUN_CLR		(1<<1)
+#define S3C64XX_SPI_PND_TRAILING_CLR		(1<<0)
+
+#define S3C64XX_SPI_SWAP_RX_HALF_WORD		(1<<7)
+#define S3C64XX_SPI_SWAP_RX_BYTE		(1<<6)
+#define S3C64XX_SPI_SWAP_RX_BIT			(1<<5)
+#define S3C64XX_SPI_SWAP_RX_EN			(1<<4)
+#define S3C64XX_SPI_SWAP_TX_HALF_WORD		(1<<3)
+#define S3C64XX_SPI_SWAP_TX_BYTE		(1<<2)
+#define S3C64XX_SPI_SWAP_TX_BIT			(1<<1)
+#define S3C64XX_SPI_SWAP_TX_EN			(1<<0)
+
+#define S3C64XX_SPI_FBCLK_MSK		(3<<0)
+
+#define S3C64XX_SPI_ST_TRLCNTZ(v, i) ((((v) >> (i)->rx_lvl_offset) & \
+					(((i)->fifo_lvl_mask + 1))) \
+					? 1 : 0)
+
+#define S3C64XX_SPI_ST_TX_DONE(v, i) ((((v) >> (i)->rx_lvl_offset) & \
+					(((i)->fifo_lvl_mask + 1) << 1)) \
+					? 1 : 0)
+#define TX_FIFO_LVL(v, i) (((v) >> 6) & (i)->fifo_lvl_mask)
+#define RX_FIFO_LVL(v, i) (((v) >> (i)->rx_lvl_offset) & (i)->fifo_lvl_mask)
+
+#define S3C64XX_SPI_MAX_TRAILCNT	0x3ff
+#define S3C64XX_SPI_TRAILCNT_OFF	19
+
+#define S3C64XX_SPI_TRAILCNT		S3C64XX_SPI_MAX_TRAILCNT
+
+#define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t)
+
+#define SUSPND    (1<<0)
+#define SPIBUSY   (1<<1)
+#define RXBUSY    (1<<2)
+#define TXBUSY    (1<<3)
+
+/**
+ * struct s3c64xx_spi_driver_data - Runtime info holder for SPI driver.
+ * @clk: Pointer to the spi clock.
+ * @master: Pointer to the SPI Protocol master.
+ * @workqueue: Work queue for the SPI xfer requests.
+ * @cntrlr_info: Platform specific data for the controller this driver manages.
+ * @tgl_spi: Pointer to the last CS left untoggled by the cs_change hint.
+ * @work: Work
+ * @queue: To log SPI xfer requests.
+ * @lock: Controller specific lock.
+ * @state: Set of FLAGS to indicate status.
+ * @rx_dmach: Controller's DMA channel for Rx.
+ * @tx_dmach: Controller's DMA channel for Tx.
+ * @sfr_start: BUS address of SPI controller regs.
+ * @regs: Pointer to ioremap'ed controller registers.
+ * @xfer_completion: To indicate completion of xfer task.
+ * @cur_mode: Stores the active configuration of the controller.
+ * @cur_bpw: Stores the active bits per word settings.
+ * @cur_speed: Stores the active xfer clock speed.
+ */
+struct s3c64xx_spi_driver_data {
+	void __iomem                    *regs;
+	struct clk                      *clk;
+	struct platform_device          *pdev;
+	struct spi_master               *master;
+	struct workqueue_struct	        *workqueue;
+	struct s3c64xx_spi_cntrlr_info  *cntrlr_info;
+	struct spi_device               *tgl_spi;
+	struct work_struct              work;
+	struct list_head                queue;
+	spinlock_t                      lock;
+	enum dma_ch                     rx_dmach;
+	enum dma_ch                     tx_dmach;
+	unsigned long                   sfr_start;
+	struct completion               xfer_completion;
+	unsigned                        state;
+	unsigned                        cur_mode, cur_bpw;
+	unsigned                        cur_speed;
+};
+
+static struct s3c2410_dma_client s3c64xx_spi_dma_client = {
+	.name = "samsung-spi-dma",
+};
+
+static void flush_fifo(struct s3c64xx_spi_driver_data *sdd)
+{
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	void __iomem *regs = sdd->regs;
+	unsigned long loops;
+	u32 val;
+
+	writel(0, regs + S3C64XX_SPI_PACKET_CNT);
+
+	val = readl(regs + S3C64XX_SPI_CH_CFG);
+	val |= S3C64XX_SPI_CH_SW_RST;
+	val &= ~S3C64XX_SPI_CH_HS_EN;
+	writel(val, regs + S3C64XX_SPI_CH_CFG);
+
+	/* Flush TxFIFO*/
+	loops = msecs_to_loops(1);
+	do {
+		val = readl(regs + S3C64XX_SPI_STATUS);
+	} while (TX_FIFO_LVL(val, sci) && loops--);
+
+	/* Flush RxFIFO*/
+	loops = msecs_to_loops(1);
+	do {
+		val = readl(regs + S3C64XX_SPI_STATUS);
+		if (RX_FIFO_LVL(val, sci))
+			readl(regs + S3C64XX_SPI_RX_DATA);
+		else
+			break;
+	} while (loops--);
+
+	val = readl(regs + S3C64XX_SPI_CH_CFG);
+	val &= ~S3C64XX_SPI_CH_SW_RST;
+	writel(val, regs + S3C64XX_SPI_CH_CFG);
+
+	val = readl(regs + S3C64XX_SPI_MODE_CFG);
+	val &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
+	writel(val, regs + S3C64XX_SPI_MODE_CFG);
+
+	val = readl(regs + S3C64XX_SPI_CH_CFG);
+	val &= ~(S3C64XX_SPI_CH_RXCH_ON | S3C64XX_SPI_CH_TXCH_ON);
+	writel(val, regs + S3C64XX_SPI_CH_CFG);
+}
+
+static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
+				struct spi_device *spi,
+				struct spi_transfer *xfer, int dma_mode)
+{
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	void __iomem *regs = sdd->regs;
+	u32 modecfg, chcfg;
+
+	modecfg = readl(regs + S3C64XX_SPI_MODE_CFG);
+	modecfg &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
+
+	chcfg = readl(regs + S3C64XX_SPI_CH_CFG);
+	chcfg &= ~S3C64XX_SPI_CH_TXCH_ON;
+
+	if (dma_mode) {
+		chcfg &= ~S3C64XX_SPI_CH_RXCH_ON;
+	} else {
+		/* Always shift in data in FIFO, even if xfer is Tx only,
+		 * this helps setting PCKT_CNT value for generating clocks
+		 * as exactly needed.
+		 */
+		chcfg |= S3C64XX_SPI_CH_RXCH_ON;
+		writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
+					| S3C64XX_SPI_PACKET_CNT_EN,
+					regs + S3C64XX_SPI_PACKET_CNT);
+	}
+
+	if (xfer->tx_buf != NULL) {
+		sdd->state |= TXBUSY;
+		chcfg |= S3C64XX_SPI_CH_TXCH_ON;
+		if (dma_mode) {
+			modecfg |= S3C64XX_SPI_MODE_TXDMA_ON;
+			s3c2410_dma_config(sdd->tx_dmach, 1);
+			s3c2410_dma_enqueue(sdd->tx_dmach, (void *)sdd,
+						xfer->tx_dma, xfer->len);
+			s3c2410_dma_ctrl(sdd->tx_dmach, S3C2410_DMAOP_START);
+		} else {
+			unsigned char *buf = (unsigned char *) xfer->tx_buf;
+			int i = 0;
+			while (i < xfer->len)
+				writeb(buf[i++], regs + S3C64XX_SPI_TX_DATA);
+		}
+	}
+
+	if (xfer->rx_buf != NULL) {
+		sdd->state |= RXBUSY;
+
+		if (sci->high_speed && sdd->cur_speed >= 30000000UL
+					&& !(sdd->cur_mode & SPI_CPHA))
+			chcfg |= S3C64XX_SPI_CH_HS_EN;
+
+		if (dma_mode) {
+			modecfg |= S3C64XX_SPI_MODE_RXDMA_ON;
+			chcfg |= S3C64XX_SPI_CH_RXCH_ON;
+			writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
+					| S3C64XX_SPI_PACKET_CNT_EN,
+					regs + S3C64XX_SPI_PACKET_CNT);
+			s3c2410_dma_config(sdd->rx_dmach, 1);
+			s3c2410_dma_enqueue(sdd->rx_dmach, (void *)sdd,
+						xfer->rx_dma, xfer->len);
+			s3c2410_dma_ctrl(sdd->rx_dmach, S3C2410_DMAOP_START);
+		}
+	}
+
+	writel(modecfg, regs + S3C64XX_SPI_MODE_CFG);
+	writel(chcfg, regs + S3C64XX_SPI_CH_CFG);
+}
+
+static inline void enable_cs(struct s3c64xx_spi_driver_data *sdd,
+						struct spi_device *spi)
+{
+	struct s3c64xx_spi_csinfo *cs;
+
+	if (sdd->tgl_spi != NULL) { /* If last device toggled after mssg */
+		if (sdd->tgl_spi != spi) { /* if last mssg on diff device */
+			/* Deselect the last toggled device */
+			cs = sdd->tgl_spi->controller_data;
+			cs->set_level(spi->mode & SPI_CS_HIGH ? 0 : 1);
+		}
+		sdd->tgl_spi = NULL;
+	}
+
+	cs = spi->controller_data;
+	cs->set_level(spi->mode & SPI_CS_HIGH ? 1 : 0);
+}
+
+static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
+				struct spi_transfer *xfer, int dma_mode)
+{
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	void __iomem *regs = sdd->regs;
+	unsigned long val;
+	int ms;
+
+	/* millisecs to xfer 'len' bytes @ 'cur_speed' */
+	ms = xfer->len * 8 * 1000 / sdd->cur_speed;
+	ms += 5; /* some tolerance */
+
+	if (dma_mode) {
+		val = msecs_to_jiffies(ms) + 10;
+		val = wait_for_completion_timeout(&sdd->xfer_completion, val);
+	} else {
+		val = msecs_to_loops(ms);
+		do {
+			val = readl(regs + S3C64XX_SPI_STATUS);
+		} while (RX_FIFO_LVL(val, sci) < xfer->len && --val);
+	}
+
+	if (!val)
+		return -EIO;
+
+	if (dma_mode) {
+		u32 status;
+
+		/*
+		 * DmaTx returns after simply writing data in the FIFO,
+		 * w/o waiting for real transmission on the bus to finish.
+		 * DmaRx returns only after Dma read data from FIFO which
+		 * needs bus transmission to finish, so we don't worry if
+		 * Xfer involved Rx(with or without Tx).
+		 */
+		if (xfer->rx_buf == NULL) {
+			val = msecs_to_loops(10);
+			status = readl(regs + S3C64XX_SPI_STATUS);
+			while ((TX_FIFO_LVL(status, sci)
+				|| !S3C64XX_SPI_ST_TX_DONE(status, sci))
+					&& --val) {
+				cpu_relax();
+				status = readl(regs + S3C64XX_SPI_STATUS);
+			}
+
+			if (!val)
+				return -EIO;
+		}
+	} else {
+		unsigned char *buf;
+		int i;
+
+		/* If it was only Tx */
+		if (xfer->rx_buf == NULL) {
+			sdd->state &= ~TXBUSY;
+			return 0;
+		}
+
+		i = 0;
+		buf = xfer->rx_buf;
+		while (i < xfer->len)
+			buf[i++] = readb(regs + S3C64XX_SPI_RX_DATA);
+
+		sdd->state &= ~RXBUSY;
+	}
+
+	return 0;
+}
+
+static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd,
+						struct spi_device *spi)
+{
+	struct s3c64xx_spi_csinfo *cs = spi->controller_data;
+
+	if (sdd->tgl_spi == spi)
+		sdd->tgl_spi = NULL;
+
+	cs->set_level(spi->mode & SPI_CS_HIGH ? 0 : 1);
+}
+
+static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
+{
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	void __iomem *regs = sdd->regs;
+	u32 val;
+
+	/* Disable Clock */
+	val = readl(regs + S3C64XX_SPI_CLK_CFG);
+	val &= ~S3C64XX_SPI_ENCLK_ENABLE;
+	writel(val, regs + S3C64XX_SPI_CLK_CFG);
+
+	/* Set Polarity and Phase */
+	val = readl(regs + S3C64XX_SPI_CH_CFG);
+	val &= ~(S3C64XX_SPI_CH_SLAVE |
+			S3C64XX_SPI_CPOL_L |
+			S3C64XX_SPI_CPHA_B);
+
+	if (sdd->cur_mode & SPI_CPOL)
+		val |= S3C64XX_SPI_CPOL_L;
+
+	if (sdd->cur_mode & SPI_CPHA)
+		val |= S3C64XX_SPI_CPHA_B;
+
+	writel(val, regs + S3C64XX_SPI_CH_CFG);
+
+	/* Set Channel & DMA Mode */
+	val = readl(regs + S3C64XX_SPI_MODE_CFG);
+	val &= ~(S3C64XX_SPI_MODE_BUS_TSZ_MASK
+			| S3C64XX_SPI_MODE_CH_TSZ_MASK);
+
+	switch (sdd->cur_bpw) {
+	case 32:
+		val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD;
+		break;
+	case 16:
+		val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD;
+		break;
+	default:
+		val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE;
+		break;
+	}
+	val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE; /* Always 8bits wide */
+
+	writel(val, regs + S3C64XX_SPI_MODE_CFG);
+
+	/* Configure Clock */
+	val = readl(regs + S3C64XX_SPI_CLK_CFG);
+	val &= ~S3C64XX_SPI_PSR_MASK;
+	val |= ((clk_get_rate(sci->src_clk) / sdd->cur_speed / 2 - 1)
+			& S3C64XX_SPI_PSR_MASK);
+	writel(val, regs + S3C64XX_SPI_CLK_CFG);
+
+	/* Enable Clock */
+	val = readl(regs + S3C64XX_SPI_CLK_CFG);
+	val |= S3C64XX_SPI_ENCLK_ENABLE;
+	writel(val, regs + S3C64XX_SPI_CLK_CFG);
+}
+
+void s3c64xx_spi_dma_rxcb(struct s3c2410_dma_chan *chan, void *buf_id,
+				int size, enum s3c2410_dma_buffresult res)
+{
+	struct s3c64xx_spi_driver_data *sdd = buf_id;
+	unsigned long flags;
+
+	spin_lock_irqsave(&sdd->lock, flags);
+
+	if (res == S3C2410_RES_OK)
+		sdd->state &= ~RXBUSY;
+	else
+		dev_err(&sdd->pdev->dev, "DmaAbrtRx-%d\n", size);
+
+	/* If the other done */
+	if (!(sdd->state & TXBUSY))
+		complete(&sdd->xfer_completion);
+
+	spin_unlock_irqrestore(&sdd->lock, flags);
+}
+
+void s3c64xx_spi_dma_txcb(struct s3c2410_dma_chan *chan, void *buf_id,
+				int size, enum s3c2410_dma_buffresult res)
+{
+	struct s3c64xx_spi_driver_data *sdd = buf_id;
+	unsigned long flags;
+
+	spin_lock_irqsave(&sdd->lock, flags);
+
+	if (res == S3C2410_RES_OK)
+		sdd->state &= ~TXBUSY;
+	else
+		dev_err(&sdd->pdev->dev, "DmaAbrtTx-%d \n", size);
+
+	/* If the other done */
+	if (!(sdd->state & RXBUSY))
+		complete(&sdd->xfer_completion);
+
+	spin_unlock_irqrestore(&sdd->lock, flags);
+}
+
+#define XFER_DMAADDR_INVALID DMA_BIT_MASK(32)
+
+static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd,
+						struct spi_message *msg)
+{
+	struct device *dev = &sdd->pdev->dev;
+	struct spi_transfer *xfer;
+
+	if (msg->is_dma_mapped)
+		return 0;
+
+	/* First mark all xfer unmapped */
+	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+		xfer->rx_dma = XFER_DMAADDR_INVALID;
+		xfer->tx_dma = XFER_DMAADDR_INVALID;
+	}
+
+	/* Map until end or first fail */
+	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+
+		if (xfer->tx_buf != NULL) {
+			xfer->tx_dma = dma_map_single(dev, xfer->tx_buf,
+						xfer->len, DMA_TO_DEVICE);
+			if (dma_mapping_error(dev, xfer->tx_dma)) {
+				dev_err(dev, "dma_map_single Tx failed\n");
+				xfer->tx_dma = XFER_DMAADDR_INVALID;
+				return -ENOMEM;
+			}
+		}
+
+		if (xfer->rx_buf != NULL) {
+			xfer->rx_dma = dma_map_single(dev, xfer->rx_buf,
+						xfer->len, DMA_FROM_DEVICE);
+			if (dma_mapping_error(dev, xfer->rx_dma)) {
+				dev_err(dev, "dma_map_single Rx failed\n");
+				dma_unmap_single(dev, xfer->tx_dma,
+						xfer->len, DMA_TO_DEVICE);
+				xfer->tx_dma = XFER_DMAADDR_INVALID;
+				xfer->rx_dma = XFER_DMAADDR_INVALID;
+				return -ENOMEM;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd,
+						struct spi_message *msg)
+{
+	struct device *dev = &sdd->pdev->dev;
+	struct spi_transfer *xfer;
+
+	if (msg->is_dma_mapped)
+		return;
+
+	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+
+		if (xfer->rx_buf != NULL
+				&& xfer->rx_dma != XFER_DMAADDR_INVALID)
+			dma_unmap_single(dev, xfer->rx_dma,
+						xfer->len, DMA_FROM_DEVICE);
+
+		if (xfer->tx_buf != NULL
+				&& xfer->tx_dma != XFER_DMAADDR_INVALID)
+			dma_unmap_single(dev, xfer->tx_dma,
+						xfer->len, DMA_TO_DEVICE);
+	}
+}
+
+static void handle_msg(struct s3c64xx_spi_driver_data *sdd,
+					struct spi_message *msg)
+{
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	struct spi_device *spi = msg->spi;
+	struct s3c64xx_spi_csinfo *cs = spi->controller_data;
+	struct spi_transfer *xfer;
+	int status = 0, cs_toggle = 0;
+	u32 speed;
+	u8 bpw;
+
+	/* If Master's(controller) state differs from that needed by Slave */
+	if (sdd->cur_speed != spi->max_speed_hz
+			|| sdd->cur_mode != spi->mode
+			|| sdd->cur_bpw != spi->bits_per_word) {
+		sdd->cur_bpw = spi->bits_per_word;
+		sdd->cur_speed = spi->max_speed_hz;
+		sdd->cur_mode = spi->mode;
+		s3c64xx_spi_config(sdd);
+	}
+
+	/* Map all the transfers if needed */
+	if (s3c64xx_spi_map_mssg(sdd, msg)) {
+		dev_err(&spi->dev,
+			"Xfer: Unable to map message buffers!\n");
+		status = -ENOMEM;
+		goto out;
+	}
+
+	/* Configure feedback delay */
+	writel(cs->fb_delay & 0x3, sdd->regs + S3C64XX_SPI_FB_CLK);
+
+	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+
+		unsigned long flags;
+		int use_dma;
+
+		INIT_COMPLETION(sdd->xfer_completion);
+
+		/* Only BPW and Speed may change across transfers */
+		bpw = xfer->bits_per_word ? : spi->bits_per_word;
+		speed = xfer->speed_hz ? : spi->max_speed_hz;
+
+		if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) {
+			sdd->cur_bpw = bpw;
+			sdd->cur_speed = speed;
+			s3c64xx_spi_config(sdd);
+		}
+
+		/* Polling method for xfers not bigger than FIFO capacity */
+		if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1))
+			use_dma = 0;
+		else
+			use_dma = 1;
+
+		spin_lock_irqsave(&sdd->lock, flags);
+
+		/* Pending only which is to be done */
+		sdd->state &= ~RXBUSY;
+		sdd->state &= ~TXBUSY;
+
+		enable_datapath(sdd, spi, xfer, use_dma);
+
+		/* Slave Select */
+		enable_cs(sdd, spi);
+
+		/* Start the signals */
+		S3C64XX_SPI_ACT(sdd);
+
+		spin_unlock_irqrestore(&sdd->lock, flags);
+
+		status = wait_for_xfer(sdd, xfer, use_dma);
+
+		/* Quiese the signals */
+		S3C64XX_SPI_DEACT(sdd);
+
+		if (status) {
+			dev_err(&spi->dev, "I/O Error: \
+				rx-%d tx-%d res:rx-%c tx-%c len-%d\n",
+				xfer->rx_buf ? 1 : 0, xfer->tx_buf ? 1 : 0,
+				(sdd->state & RXBUSY) ? 'f' : 'p',
+				(sdd->state & TXBUSY) ? 'f' : 'p',
+				xfer->len);
+
+			if (use_dma) {
+				if (xfer->tx_buf != NULL
+						&& (sdd->state & TXBUSY))
+					s3c2410_dma_ctrl(sdd->tx_dmach,
+							S3C2410_DMAOP_FLUSH);
+				if (xfer->rx_buf != NULL
+						&& (sdd->state & RXBUSY))
+					s3c2410_dma_ctrl(sdd->rx_dmach,
+							S3C2410_DMAOP_FLUSH);
+			}
+
+			goto out;
+		}
+
+		if (xfer->delay_usecs)
+			udelay(xfer->delay_usecs);
+
+		if (xfer->cs_change) {
+			/* Hint that the next mssg is gonna be
+			   for the same device */
+			if (list_is_last(&xfer->transfer_list,
+						&msg->transfers))
+				cs_toggle = 1;
+			else
+				disable_cs(sdd, spi);
+		}
+
+		msg->actual_length += xfer->len;
+
+		flush_fifo(sdd);
+	}
+
+out:
+	if (!cs_toggle || status)
+		disable_cs(sdd, spi);
+	else
+		sdd->tgl_spi = spi;
+
+	s3c64xx_spi_unmap_mssg(sdd, msg);
+
+	msg->status = status;
+
+	if (msg->complete)
+		msg->complete(msg->context);
+}
+
+static int acquire_dma(struct s3c64xx_spi_driver_data *sdd)
+{
+	if (s3c2410_dma_request(sdd->rx_dmach,
+					&s3c64xx_spi_dma_client, NULL) < 0) {
+		dev_err(&sdd->pdev->dev, "cannot get RxDMA\n");
+		return 0;
+	}
+	s3c2410_dma_set_buffdone_fn(sdd->rx_dmach, s3c64xx_spi_dma_rxcb);
+	s3c2410_dma_devconfig(sdd->rx_dmach, S3C2410_DMASRC_HW,
+					sdd->sfr_start + S3C64XX_SPI_RX_DATA);
+
+	if (s3c2410_dma_request(sdd->tx_dmach,
+					&s3c64xx_spi_dma_client, NULL) < 0) {
+		dev_err(&sdd->pdev->dev, "cannot get TxDMA\n");
+		s3c2410_dma_free(sdd->rx_dmach, &s3c64xx_spi_dma_client);
+		return 0;
+	}
+	s3c2410_dma_set_buffdone_fn(sdd->tx_dmach, s3c64xx_spi_dma_txcb);
+	s3c2410_dma_devconfig(sdd->tx_dmach, S3C2410_DMASRC_MEM,
+					sdd->sfr_start + S3C64XX_SPI_TX_DATA);
+
+	return 1;
+}
+
+static void s3c64xx_spi_work(struct work_struct *work)
+{
+	struct s3c64xx_spi_driver_data *sdd = container_of(work,
+					struct s3c64xx_spi_driver_data, work);
+	unsigned long flags;
+
+	/* Acquire DMA channels */
+	while (!acquire_dma(sdd))
+		msleep(10);
+
+	spin_lock_irqsave(&sdd->lock, flags);
+
+	while (!list_empty(&sdd->queue)
+				&& !(sdd->state & SUSPND)) {
+
+		struct spi_message *msg;
+
+		msg = container_of(sdd->queue.next, struct spi_message, queue);
+
+		list_del_init(&msg->queue);
+
+		/* Set Xfer busy flag */
+		sdd->state |= SPIBUSY;
+
+		spin_unlock_irqrestore(&sdd->lock, flags);
+
+		handle_msg(sdd, msg);
+
+		spin_lock_irqsave(&sdd->lock, flags);
+
+		sdd->state &= ~SPIBUSY;
+	}
+
+	spin_unlock_irqrestore(&sdd->lock, flags);
+
+	/* Free DMA channels */
+	s3c2410_dma_free(sdd->tx_dmach, &s3c64xx_spi_dma_client);
+	s3c2410_dma_free(sdd->rx_dmach, &s3c64xx_spi_dma_client);
+}
+
+static int s3c64xx_spi_transfer(struct spi_device *spi,
+						struct spi_message *msg)
+{
+	struct s3c64xx_spi_driver_data *sdd;
+	unsigned long flags;
+
+	sdd = spi_master_get_devdata(spi->master);
+
+	spin_lock_irqsave(&sdd->lock, flags);
+
+	if (sdd->state & SUSPND) {
+		spin_unlock_irqrestore(&sdd->lock, flags);
+		return -ESHUTDOWN;
+	}
+
+	msg->status = -EINPROGRESS;
+	msg->actual_length = 0;
+
+	list_add_tail(&msg->queue, &sdd->queue);
+
+	queue_work(sdd->workqueue, &sdd->work);
+
+	spin_unlock_irqrestore(&sdd->lock, flags);
+
+	return 0;
+}
+
+/*
+ * Here we only check the validity of requested configuration
+ * and save the configuration in a local data-structure.
+ * The controller is actually configured only just before we
+ * get a message to transfer.
+ */
+static int s3c64xx_spi_setup(struct spi_device *spi)
+{
+	struct s3c64xx_spi_csinfo *cs = spi->controller_data;
+	struct s3c64xx_spi_driver_data *sdd;
+	struct s3c64xx_spi_cntrlr_info *sci;
+	struct spi_message *msg;
+	u32 psr, speed;
+	unsigned long flags;
+	int err = 0;
+
+	if (cs == NULL || cs->set_level == NULL) {
+		dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select);
+		return -ENODEV;
+	}
+
+	sdd = spi_master_get_devdata(spi->master);
+	sci = sdd->cntrlr_info;
+
+	spin_lock_irqsave(&sdd->lock, flags);
+
+	list_for_each_entry(msg, &sdd->queue, queue) {
+		/* Is some mssg is already queued for this device */
+		if (msg->spi == spi) {
+			dev_err(&spi->dev,
+				"setup: attempt while mssg in queue!\n");
+			spin_unlock_irqrestore(&sdd->lock, flags);
+			return -EBUSY;
+		}
+	}
+
+	if (sdd->state & SUSPND) {
+		spin_unlock_irqrestore(&sdd->lock, flags);
+		dev_err(&spi->dev,
+			"setup: SPI-%d not active!\n", spi->master->bus_num);
+		return -ESHUTDOWN;
+	}
+
+	spin_unlock_irqrestore(&sdd->lock, flags);
+
+	if (spi->bits_per_word != 8
+			&& spi->bits_per_word != 16
+			&& spi->bits_per_word != 32) {
+		dev_err(&spi->dev, "setup: %dbits/wrd not supported!\n",
+							spi->bits_per_word);
+		err = -EINVAL;
+		goto setup_exit;
+	}
+
+	/* Check if we can provide the requested rate */
+	speed = clk_get_rate(sci->src_clk) / 2 / (0 + 1); /* Max possible */
+
+	if (spi->max_speed_hz > speed)
+		spi->max_speed_hz = speed;
+
+	psr = clk_get_rate(sci->src_clk) / 2 / spi->max_speed_hz - 1;
+	psr &= S3C64XX_SPI_PSR_MASK;
+	if (psr == S3C64XX_SPI_PSR_MASK)
+		psr--;
+
+	speed = clk_get_rate(sci->src_clk) / 2 / (psr + 1);
+	if (spi->max_speed_hz < speed) {
+		if (psr+1 < S3C64XX_SPI_PSR_MASK) {
+			psr++;
+		} else {
+			err = -EINVAL;
+			goto setup_exit;
+		}
+	}
+
+	speed = clk_get_rate(sci->src_clk) / 2 / (psr + 1);
+	if (spi->max_speed_hz >= speed)
+		spi->max_speed_hz = speed;
+	else
+		err = -EINVAL;
+
+setup_exit:
+
+	/* setup() returns with device de-selected */
+	disable_cs(sdd, spi);
+
+	return err;
+}
+
+static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel)
+{
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	void __iomem *regs = sdd->regs;
+	unsigned int val;
+
+	sdd->cur_speed = 0;
+
+	S3C64XX_SPI_DEACT(sdd);
+
+	/* Disable Interrupts - we use Polling if not DMA mode */
+	writel(0, regs + S3C64XX_SPI_INT_EN);
+
+	writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
+				regs + S3C64XX_SPI_CLK_CFG);
+	writel(0, regs + S3C64XX_SPI_MODE_CFG);
+	writel(0, regs + S3C64XX_SPI_PACKET_CNT);
+
+	/* Clear any irq pending bits */
+	writel(readl(regs + S3C64XX_SPI_PENDING_CLR),
+				regs + S3C64XX_SPI_PENDING_CLR);
+
+	writel(0, regs + S3C64XX_SPI_SWAP_CFG);
+
+	val = readl(regs + S3C64XX_SPI_MODE_CFG);
+	val &= ~S3C64XX_SPI_MODE_4BURST;
+	val &= ~(S3C64XX_SPI_MAX_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
+	val |= (S3C64XX_SPI_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
+	writel(val, regs + S3C64XX_SPI_MODE_CFG);
+
+	flush_fifo(sdd);
+}
+
+static int __init s3c64xx_spi_probe(struct platform_device *pdev)
+{
+	struct resource	*mem_res, *dmatx_res, *dmarx_res;
+	struct s3c64xx_spi_driver_data *sdd;
+	struct s3c64xx_spi_cntrlr_info *sci;
+	struct spi_master *master;
+	int ret;
+
+	if (pdev->id < 0) {
+		dev_err(&pdev->dev,
+				"Invalid platform device id-%d\n", pdev->id);
+		return -ENODEV;
+	}
+
+	if (pdev->dev.platform_data == NULL) {
+		dev_err(&pdev->dev, "platform_data missing!\n");
+		return -ENODEV;
+	}
+
+	/* Check for availability of necessary resource */
+
+	dmatx_res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+	if (dmatx_res == NULL) {
+		dev_err(&pdev->dev, "Unable to get SPI-Tx dma resource\n");
+		return -ENXIO;
+	}
+
+	dmarx_res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+	if (dmarx_res == NULL) {
+		dev_err(&pdev->dev, "Unable to get SPI-Rx dma resource\n");
+		return -ENXIO;
+	}
+
+	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (mem_res == NULL) {
+		dev_err(&pdev->dev, "Unable to get SPI MEM resource\n");
+		return -ENXIO;
+	}
+
+	master = spi_alloc_master(&pdev->dev,
+				sizeof(struct s3c64xx_spi_driver_data));
+	if (master == NULL) {
+		dev_err(&pdev->dev, "Unable to allocate SPI Master\n");
+		return -ENOMEM;
+	}
+
+	sci = pdev->dev.platform_data;
+
+	platform_set_drvdata(pdev, master);
+
+	sdd = spi_master_get_devdata(master);
+	sdd->master = master;
+	sdd->cntrlr_info = sci;
+	sdd->pdev = pdev;
+	sdd->sfr_start = mem_res->start;
+	sdd->tx_dmach = dmatx_res->start;
+	sdd->rx_dmach = dmarx_res->start;
+
+	sdd->cur_bpw = 8;
+
+	master->bus_num = pdev->id;
+	master->setup = s3c64xx_spi_setup;
+	master->transfer = s3c64xx_spi_transfer;
+	master->num_chipselect = sci->num_cs;
+	master->dma_alignment = 8;
+	/* the spi->mode bits understood by this driver: */
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+
+	if (request_mem_region(mem_res->start,
+			resource_size(mem_res), pdev->name) == NULL) {
+		dev_err(&pdev->dev, "Req mem region failed\n");
+		ret = -ENXIO;
+		goto err0;
+	}
+
+	sdd->regs = ioremap(mem_res->start, resource_size(mem_res));
+	if (sdd->regs == NULL) {
+		dev_err(&pdev->dev, "Unable to remap IO\n");
+		ret = -ENXIO;
+		goto err1;
+	}
+
+	if (sci->cfg_gpio == NULL || sci->cfg_gpio(pdev)) {
+		dev_err(&pdev->dev, "Unable to config gpio\n");
+		ret = -EBUSY;
+		goto err2;
+	}
+
+	/* Setup clocks */
+	sdd->clk = clk_get(&pdev->dev, "spi");
+	if (IS_ERR(sdd->clk)) {
+		dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n");
+		ret = PTR_ERR(sdd->clk);
+		goto err3;
+	}
+
+	if (clk_enable(sdd->clk)) {
+		dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n");
+		ret = -EBUSY;
+		goto err4;
+	}
+
+	if (sci->src_clk_nr == S3C64XX_SPI_SRCCLK_PCLK)
+		sci->src_clk = sdd->clk;
+	else
+		sci->src_clk = clk_get(&pdev->dev, sci->src_clk_name);
+	if (IS_ERR(sci->src_clk)) {
+		dev_err(&pdev->dev,
+			"Unable to acquire clock '%s'\n", sci->src_clk_name);
+		ret = PTR_ERR(sci->src_clk);
+		goto err5;
+	}
+
+	if (sci->src_clk != sdd->clk && clk_enable(sci->src_clk)) {
+		dev_err(&pdev->dev, "Couldn't enable clock '%s'\n",
+							sci->src_clk_name);
+		ret = -EBUSY;
+		goto err6;
+	}
+
+	sdd->workqueue = create_singlethread_workqueue(
+						dev_name(master->dev.parent));
+	if (sdd->workqueue == NULL) {
+		dev_err(&pdev->dev, "Unable to create workqueue\n");
+		ret = -ENOMEM;
+		goto err7;
+	}
+
+	/* Setup Deufult Mode */
+	s3c64xx_spi_hwinit(sdd, pdev->id);
+
+	spin_lock_init(&sdd->lock);
+	init_completion(&sdd->xfer_completion);
+	INIT_WORK(&sdd->work, s3c64xx_spi_work);
+	INIT_LIST_HEAD(&sdd->queue);
+
+	if (spi_register_master(master)) {
+		dev_err(&pdev->dev, "cannot register SPI master\n");
+		ret = -EBUSY;
+		goto err8;
+	}
+
+	dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d \
+					with %d Slaves attached\n",
+					pdev->id, master->num_chipselect);
+	dev_dbg(&pdev->dev, "\tIOmem=[0x%x-0x%x]\
+					\tDMA=[Rx-%d, Tx-%d]\n",
+					mem_res->end, mem_res->start,
+					sdd->rx_dmach, sdd->tx_dmach);
+
+	return 0;
+
+err8:
+	destroy_workqueue(sdd->workqueue);
+err7:
+	if (sci->src_clk != sdd->clk)
+		clk_disable(sci->src_clk);
+err6:
+	if (sci->src_clk != sdd->clk)
+		clk_put(sci->src_clk);
+err5:
+	clk_disable(sdd->clk);
+err4:
+	clk_put(sdd->clk);
+err3:
+err2:
+	iounmap((void *) sdd->regs);
+err1:
+	release_mem_region(mem_res->start, resource_size(mem_res));
+err0:
+	platform_set_drvdata(pdev, NULL);
+	spi_master_put(master);
+
+	return ret;
+}
+
+static int s3c64xx_spi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
+	struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	struct resource	*mem_res;
+	unsigned long flags;
+
+	spin_lock_irqsave(&sdd->lock, flags);
+	sdd->state |= SUSPND;
+	spin_unlock_irqrestore(&sdd->lock, flags);
+
+	while (sdd->state & SPIBUSY)
+		msleep(10);
+
+	spi_unregister_master(master);
+
+	destroy_workqueue(sdd->workqueue);
+
+	if (sci->src_clk != sdd->clk)
+		clk_disable(sci->src_clk);
+
+	if (sci->src_clk != sdd->clk)
+		clk_put(sci->src_clk);
+
+	clk_disable(sdd->clk);
+	clk_put(sdd->clk);
+
+	iounmap((void *) sdd->regs);
+
+	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	release_mem_region(mem_res->start, resource_size(mem_res));
+
+	platform_set_drvdata(pdev, NULL);
+	spi_master_put(master);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int s3c64xx_spi_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
+	struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	struct s3c64xx_spi_csinfo *cs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&sdd->lock, flags);
+	sdd->state |= SUSPND;
+	spin_unlock_irqrestore(&sdd->lock, flags);
+
+	while (sdd->state & SPIBUSY)
+		msleep(10);
+
+	/* Disable the clock */
+	if (sci->src_clk != sdd->clk)
+		clk_disable(sci->src_clk);
+
+	clk_disable(sdd->clk);
+
+	sdd->cur_speed = 0; /* Output Clock is stopped */
+
+	return 0;
+}
+
+static int s3c64xx_spi_resume(struct platform_device *pdev)
+{
+	struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
+	struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
+	struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+	unsigned long flags;
+
+	sci->cfg_gpio(pdev);
+
+	/* Enable the clock */
+	if (sci->src_clk != sdd->clk)
+		clk_enable(sci->src_clk);
+
+	clk_enable(sdd->clk);
+
+	s3c64xx_spi_hwinit(sdd, pdev->id);
+
+	spin_lock_irqsave(&sdd->lock, flags);
+	sdd->state &= ~SUSPND;
+	spin_unlock_irqrestore(&sdd->lock, flags);
+
+	return 0;
+}
+#else
+#define s3c64xx_spi_suspend	NULL
+#define s3c64xx_spi_resume	NULL
+#endif /* CONFIG_PM */
+
+static struct platform_driver s3c64xx_spi_driver = {
+	.driver = {
+		.name	= "s3c64xx-spi",
+		.owner = THIS_MODULE,
+	},
+	.remove = s3c64xx_spi_remove,
+	.suspend = s3c64xx_spi_suspend,
+	.resume = s3c64xx_spi_resume,
+};
+MODULE_ALIAS("platform:s3c64xx-spi");
+
+static int __init s3c64xx_spi_init(void)
+{
+	return platform_driver_probe(&s3c64xx_spi_driver, s3c64xx_spi_probe);
+}
+module_init(s3c64xx_spi_init);
+
+static void __exit s3c64xx_spi_exit(void)
+{
+	platform_driver_unregister(&s3c64xx_spi_driver);
+}
+module_exit(s3c64xx_spi_exit);
+
+MODULE_AUTHOR("Jaswinder Singh <jassi.brar@samsung.com>");
+MODULE_DESCRIPTION("S3C64XX SPI Controller Driver");
+MODULE_LICENSE("GPL");