@@ -91,6 +91,7 @@ struct flexcop_device {
int feedcount;
int pid_filtering;
int fullts_streaming_state;
+ int skip_6_hw_pid_filter;
/* bus specific callbacks */
flexcop_ibi_value(*read_ibi_reg) (struct flexcop_device *,
@@ -651,6 +651,9 @@ static int skystarS2_rev33_attach(struct flexcop_device *fc,
}
info("ISL6421 successfully attached.");
+ if (fc->has_32_hw_pid_filter)
+ fc->skip_6_hw_pid_filter = 1;
+
return 1;
}
#else
@@ -117,6 +117,10 @@ static void flexcop_pid_control(struct flexcop_device *fc,
deb_ts("setting pid: %5d %04x at index %d '%s'\n",
pid, pid, index, onoff ? "on" : "off");
+ /* First 6 can be buggy - skip over them if option set */
+ if (fc->skip_6_hw_pid_filter)
+ index += 6;
+
/* We could use bit magic here to reduce source code size.
* I decided against it, but to use the real register names */
switch (index) {
@@ -170,7 +174,10 @@ static int flexcop_toggle_fullts_streaming(struct flexcop_device *fc, int onoff)
int flexcop_pid_feed_control(struct flexcop_device *fc,
struct dvb_demux_feed *dvbdmxfeed, int onoff)
{
- int max_pid_filter = 6 + fc->has_32_hw_pid_filter*32;
+ int max_pid_filter = 6;
+
+ max_pid_filter -= 6 * fc->skip_6_hw_pid_filter;
+ max_pid_filter += 32 * fc->has_32_hw_pid_filter;
fc->feedcount += onoff ? 1 : -1; /* the number of PIDs/Feed currently requested */
if (dvbdmxfeed->index >= max_pid_filter)
@@ -217,7 +224,12 @@ void flexcop_hw_filter_init(struct flexcop_device *fc)
{
int i;
flexcop_ibi_value v;
- for (i = 0; i < 6 + 32*fc->has_32_hw_pid_filter; i++)
+ int max_pid_filter = 6;
+
+ max_pid_filter -= 6 * fc->skip_6_hw_pid_filter;
+ max_pid_filter += 32 * fc->has_32_hw_pid_filter;
+
+ for (i = 0; i < max_pid_filter; i++)
flexcop_pid_control(fc, i, 0x1fff, 0);
flexcop_pid_group_filter(fc, 0, 0x1fe0);
The flexcop bridge chip has two banks of hardware pid filters - an initial 6, and on some chip revisions an additional bank of 32. A bug is present on the initial 6 - when changing transponders one of two PAT packets from the old transponder would be included in the initial packets from the new transponder. This usually transpired with userspace programs complaining about services missing, because they are seeing a PAT that they would not be expecting. Running in full TS mode does not exhibit this problem, neither does using just the additional 32. This patch adds in an option to not use the inital 6 and solely use just the additional 32, and enables this option for the SkystarS2 card. Other cards can be added as required if they also have this bug. Signed-off-by: Jemma Denson <jdenson@gmail.com> --- drivers/media/common/b2c2/flexcop-common.h | 1 + drivers/media/common/b2c2/flexcop-fe-tuner.c | 3 +++ drivers/media/common/b2c2/flexcop-hw-filter.c | 16 ++++++++++++++-- 3 files changed, 18 insertions(+), 2 deletions(-)